Ver 2.0.
Drive Partner for your Safety USER GUIDE Model: BX1000 / BX1000 Plus Ver 2.0.0 2nd Edition ● Thank you for purchasing this Drive Recorder. ● Please ensure that you read and understand this USER GUIDE and use it before connecting and installing this Recorder. ● Please store the USER GUIDE in an easily accessible location.
SAFETY ADVICE CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Please make sure you follow the safety advice/instructions given in the user guide. Caution RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Drive Partner for your Safety GPS Reception 1. Activate the product in an area without large buildings toimprove GPS reception. The commercial purpose GPS has the average rage error of more than 15 meters and the range error could be more than 100 meters due to environmental conditions like buildings, roadside trees etc. BX1000 / BX1000 Plus User Guide CONTENTS 1. Smarty BX1000 / BX1000 Plus unit 2. The temperature range for optimum operation of the GPS receiver in your car is -10 ~ 50°C. 3.
Drive Partner for your Safety BX1000 / BX1000 Plus User Guide INTRODUCTION Front INTRODUCTION Back Bracket Internal GPS Antenna [Adhere tape on bracket] Record LED (BLUE LED) Camera Lens Overwrite LED (RED LED) SD Card Format Button Record Button UNIT PARTS DC Power In (DC 12~24V) PWR - + [Main unit] [Bracket] [Holder] SD Memory Card Slot Left side Right Side NOTE Formatting [initializing] SD memory card can be done using SD Card Format Button.
Drive Partner for your Safety INSTALLATION Park your vehicle on a flat level surface. Turn off the engine before installing the BX1000 / BX1000 Plus. 1. Insert the SD memory card into the SD card slot. Please make sure to disconnect the power cable when inserting or ejecting the SD memory card. BX1000 / BX1000 Plus User Guide INSTALLATION 3. Adjust camera view. Make sure the lens has an unobstructed view. Check from outside the vehicle to check the camera angle.
Drive Partner for your Safety FUNCTION Automatic start Connect your vehicle’s power cable to the BX1000 / BX1000 Plus after starting the vehicle. Then BX1000 / BX1000 Plus will be automatically started. (Use the provided power cable.) NOTE The unit will not start recording immediately after power on. It takes around 1 minute for the built-in power backup system to charge. Thereafter, the internal flash memory will be ready to record.
Drive Partner for your Safety SOFTWARE USER GUIDE BX1000 / BX1000 Plus PC Viewer Guide BX1000 / BX1000 Plus User Guide SOFTWARE INSTALLATION PC Viewer Software is provided on the SD card. 1. Connect the SD card into your PC (if your computer does not have SD card slot use the USB SD card reader) and open the “My Computer” 2. Right-click the “DRIVEREC1” drive and select [Open] 3. Double click [SETUP.EXE] at [pcsw] folder. 4. Select the language and then follow the dialog box.
Drive Partner for your Safety BX1000 / BX1000 Plus User Guide Connect SD memory card 1. Connect SD memory card into the SD card reader. PC Viewer Software Setting This setting is for the PC Viewer itself. To set the Drive Recorder, refer to page 27. 2. Run “PC Viewer BX1000” 3. Select [File] and then click “Select Data Folder” or Click [OPEN] button [OPEN] button 14 The ‘date’ formats and ‘speed’ unit will be set automatically according to the PC windows setting.
Drive Partner for your Safety BX1000 / BX1000 Plus User Guide Select file for playback FILE LOADING When Record Method set as “Event record” Check the event “G-Senor” means recording was activated by impact 6.
Drive Partner for your Safety BX1000 / BX1000 Plus User Guide PLAYBACK SCREEN PLAYBACK When Record Method set as “Event record” 7. Click play button for playback.
Drive Partner for your Safety BX1000 / BX1000 Plus User Guide PLAYBACK Google map (Supported by the “BX1000 Plus” only) NOTE: PC Keyboard hot buttons Function 1024x768 mode Full screen mode Playback speed control Reverse playback speed control The route taken will be displayed on the Google map at lower right corner of the software. PC keyboard hot buttons To see the route & position on Google Maps, the GPS data should be recorded with video.
Drive Partner for your Safety BX1000 / BX1000 Plus User Guide Thumbnail Function 7. Click the button for 4x4 multi view (Thumbnail function) Save JPG file & AVI file 9. Pause the playback and click ‘Save Image’ icon to make a JPG file. ‘Save Image’ icon 22 23 Click the thumbnail image to change the playback position. Click right the mouse button to single image playback mode. 10. Click ‘Save AVI’ icon to make a AVI file. ‘Save AVI’ icon 8. Click [Close] button to quit the playback.
Drive Partner for your Safety BX1000 / BX1000 Plus User Guide Print image Make Report 11. Pause the playback and click ‘Print Image’ icon. Print image icon 24 12. Click [Print] button in the print preview windows for printing. The File Name [Print Title], Comment [Print Comment], G-sensor graph & map (for BX1000 Plus Model only) will be printed on the first page. 25 Type in the File Name [Print Title] & any comments [Print Comment] using the Keyboard.
Drive Partner for your Safety Backup Event/Log files 13. Click [Backup Event/Log files] icon to backup the files to the PC. BX1000 / BX1000 Plus User Guide Setting Drive Recorder 14. Click [Recorder Setting] icon for setup. [Backup Event/Log files] icon [Recorder Setting] icon Caution Backup the SD data first, before clicking initialize SDcard button. Once done, the old data cannot be recovered.
Drive Partner for your Safety Setting Drive Recorder Beep on record “Beep” sound ON/OFF when Event recording start G-sensor setting Check simple setting mode and then change the sensitivity. High sensitivity like 8 or 9 means recording will be started at very low impact. Date / Time Automatically synchronize with GPS time. However Manual time setting is also available.
Drive Partner for your Safety Product Information 15. Click [About] icon to check the product information. About icon BX1000 / BX1000 Plus User Guide LOG FILE PLAYBACK 16. Select [LOG] windows and then check the log from the log list using mouse or click [Check All] button. Then click [Load] button. Log data Log data will be recorded during driving even if there are no events. The total log data size is no more than 60MB. The log data overwrites the oldest data when 60MB is reached.
Drive Partner for your Safety BX1000 / BX1000 Plus User Guide GPS LOG TO KML CONVERTER (for Google Earth) To see the whole route on Google Earth, select the log file and click Google Earth button. (BX1000 Plus only) Image sensor 1/4" CMOS DSP Standard DSP Angle of View 170° Video resolution 640x480, 320x240 Recording Speed Up to 30 fps STEP3. Click Google Earth button Recording Modes The route will then be shown on Google Earth. Continuous By impact By emergency button.
Drive Partner for your Safety BX1000 / BX1000 Plus User Guide Recording time table Resolution Quality HIGH Size 40KB 640x480 LOW HIGH 34 20KB 15KB 320X240 LOW 10KB Technical Support & Warranty TECHNICAL SUPPORT FPS 2GB 4GB 8GB 16GB 1 555 min 1408 min 3115 min 109 hours For Technical Support, please contact your local distributor. 5 111 min 282 min 623 min 22 hours LIMITED WARRANTY 10 55 min 141 min 311 min 11 hours This product is supplied with 1 year warranty.
Drive Partner for your Safety BX1000 / BX1000 Plus User Guide Optional Accessory (Permanent Power Cable) Model name: DPWR-100 The permanent power supply cable will allow you to hard wire the BX1000 series to the fuse box of your vehicle. APPENDIX (Upgrade) 1) Upgrade the BX1000 / BX1000 Plus main unit first. 2) Install new PC viewer software on your PC. 3) Initialize the SD card using new PC viewer software. NOTE To get the upgrade firmware, please contact your local distributor. 1.
Drive Partner for your Safety APPENDIX (Upgrade BX1000 / BX1000 Plus) 3. Uninstall the old version PC Viewer Software from the PC PC Windows [Start] => [Control panel] And uninstall [PCViewer] 4. Install the new PC Viewer Run setup.exe and install the new PC Viewer X.X.X.X NOTE After installation the new PC Viewer, initialize the SD card. The new software will automatically be copied to [pcsw] folder at SD card. To initialise the SD card.
Drive Partner for your Safety 3F, Jungmin Bldg, 382-2, Yatap-dong, Bundang-gu, Seongnam, Gyeonggi-do 463-827, Korea Tel: 82-31-706-2514 , Fax: 82-31-706-2519 Email: dteg@d-teg.com Homepage: http://www.d-teg.com ©2009 D-TEG Security Co., Ltd.
