User Manual English TFT-LCD Color Monitor FS-L4201C www.tandberg.net Printed in Korea Part No.
INFORMATION TO USER : This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Parts Connection to Signal Source Basic Connection 42 " LCD Monitor User's Manual This monitor do not provide any other accessaries and peripheral devices (ex,speaker and signal cable) because the Tandberg's reguest. LCD MONITOR 3 User s Manual AC Inlet.
O ut Drawing of product < Power source connection > < Signal cable connection> D-Sub Analog(Data in) DVI Digital Coaxial S/PDIF Input AC Inlet Audio amp Output AC on/off swith 1. Use 220 V or 110 V. (Free Voltage) 2. Connect monitor and Signal Source via Signal cable 3. Power on the monitor and computer. 4. Connection is finished.
Name and Function Front side Power Management Feature Rear side Power management system of this monitor can not be corresponded with VESA DPMS when the display video signal is none because the specific character of Tandberg system Status LED Sign Power Consumption Normal mode Green on Normal Power Stand by mode Red on 20W or Below Power indicating LED Remote signal window SOURCE BUTTON MENU BUTTON - BUTTON OK BUTTON + BUTTON BUTTON BUTTON LCD MONITOR 7 User s Manual LCD MONITOR 8 U
Adjusting OSD Functions Remote signal wirdow This window is for the receiving signal from remote controller Do not hide this window. Power Indicating LED Green : Normal mode RED : Standby mode On-Screen Display (OSD) Function Button PICTURE MENU : With OSD deactivated, Activated to OSD menu With OSD activated, Exit from main menu or sub menu. OK : With OSD deactivated, you can see the kind of displayed source on the right bottom side of the screen.
Standard Signal Table IMAGE PC Supported Mode 1. IMAGE SIZE Change the image size (Scaling mode) (Full,Fill aspect, 1:1) 2. SHARPNESS Set the sharpness of image (Softest,Softest,Normal,Sharp,Sharpest) 3. RESET SETTINGS Changes all OSD values to factory outgoing status. SETUP 1. LANGUAGE Change the OSD language orean,English,French,Spanish,German,Chinese,Japanese,Italian 2. OSD COLOR Adjust the OSD back ground from white opaque to half translucent. 3. OSD POSITION Change the OSD position (9 postions) 4.
Pin assignment table of signal connector Pin No. 1 2 3 4 5 6 7 8 Pin No. 1 2 3 4 5 Assignment Red Green Blue Ground DDC 5V Standby Cable Connection check Ground-Red Ground-Green Ground-Blue Assignment T.M.D.S. Data2T.M.D.S. Data2+ T.M.D.S. Data2 Shield No Connect No Connect Pin No. 9 10 11 12 13 14 15 Assignment NC Ground-Sync Ground DDC Data H.Sync V.Sync DDC Clock Pin No. Assignment 13 No Connect 14 No Connect 15 Cable Connection check 16 Hot Plug Detect 17 T.M.D.S.
Specification Model LCD Panel FS-L4201C Type a-si TFT Active matrix Screen Size 106.7cm (Diagonal) Maximum Resolution 1366 X 768@ 60 Hz Pixel Range 0.681(H) mm X 0.227(V) mm Display Colors 16.7M (RGB 8-bit data) Contrast Ratio 1000 : 1 Viewing Angle 89° / 89° / 89° / 89° Response Time 10 msec Luminance 500 cd/m Horizontal Frequency 91kHz (Max.) Synchro nization Vertical Frequency Maximum Power Consumption standby Mode Compati bility Safety Standard & EMI Dimension Power LED is dark.
Warning To prevent damage or loss, please read this warning carefully. Double images or 'ghosts'. Picture is dark. Check the resolution and frequency of computer and video card, and set up again in reference to the current monitor mode and standard signal mode table. (Refer to page 5) When connecting/disconnecting the plug, pull out the plug itself, and never pull the cord to prevent fire caused by short. Adjust COLOR at User Mode in OSD Color Temp Menu.
19 - English
