FS-L2401D( 24" ) MEDIC AL LCD MONITOR USER'S GUIDE
Table of Contents Symbol Definitions 2 Safety Instructions 4 Caution 7 FCC Information 10 Parts 12 Connector 13 Mechanical Product Drawing 14 Control 15 Power mangement 18 Adjust OSD Menu 19 Stansard Signal table 22 Signal connector Pin Assignments 23 Specification 26 English - 1
Symbol Definitions The following symbols appear on the product. its labeling, or the product packing. Each symbol carries a special definition, as defined below Dangerous : High Voltage. Consult accompanying documents. Maximum Stacking. Indicats proof of conformity to applicable European Econmic Community Council directives and to harmonzed standards published in the official journal of the European Communities. Medical Equipment is in accordance with UL 60601-1 and CAN/CSA C22.2 No.601.
Safety Instructions On Safety 1.Before connecting the AC power cord to the DC adapter outlet make sure the voltage designation of the DC adapter corresponds to the local electrical supply. 2.Never insert anything metallic into the cabinet openings of the Liquid Crystal Display(LCD) monitor. doing so may create the danger of electric shock. 3.To reduce the risk of electric shock, do not remove cover. No user-serviceable parts inside. Only a qualified technician should open the case of the LCD monitor. 4.
CAUTION Environmental Conditions for transport and Storage - Temperature range within -30°C to 85°C - Relative humidity range 5% to 95% Atrnospheric pressure range within 500 to 1060hPs. . This symbol alerts the user that important literature concerning the operation of this unit has been included. Therefore, it should be read carefully in order to avoid potential problems. This symbol warms user that un-insulated voltage within the unit the may have sufficient magnitude to cause electrical shock.
EEC Safety Compliance: This display unit meets the requirements of EN-60601-1 so as to conform to the Medical Device Directive 93/42/EEC (general safety information). This monitor complies to the above standards only when used with the supplied medical grade power supply. JWM1150KA2400F04(Ault korea corp.) The monitor should be powered from a center tapped circuit when used in the US at voltages over 120 volts. Monitor is intended for continuous operation.
FCC Information Quick Startup This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference. This monitor can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may interfere with other radio communications equipment. There is no guarantee that interference will not occur in a particular installation.
Connector Parts Back Panel Jacks 24" LCD Monitor Accessories User Manual DVI Cable D-SUB Cable AC Adapter BNC Cable AC Power code (Hospital Grade) S-Video (Y/C) Cable DC Cable Terminal male / female (Option) AC ON/OFF SWITCH S-VIDEO/Y AC Inlet S-VIDEO/C OPTICAL IN C-VIDEO DVI IN RED /Pr DVI OUT GREEN/Y VGA IN BLUE/Pb RS232C C-SYNC/H-SYNC SDI IN V-SYNC SDI OUT TOUCH(OPTION) SCREW FH M3X6 (Option) 12- English English - 13
Control Mechanical Product Drawing OSD Button Position 14 - English English - 15
OSD Button Function An 8 button keypad, located in button light corner on the front of the display, allows the user to make adjustments to various display parameters using the On Screen Display (OSD) system. Power Indicating LED Green : Normal mode Red : Standby mode OFF : Monitor Off On-Screen Display (OSD) Function Button 1 POWER : Turns ON/OFF the monitor. 2 MENU : With OSD deactivated, Activated to OSD menu. With OSD activated, Exit from main menu or sub menu.
Power management Adjusting OSD This monitor does not adhere to the VESA DPMS standard when no signal is present on the video inputs. ADJUST Status Normal Mode Standby Mode LED sign Green on Red Blinking Power Consumption <100W <20W BRIGHTNESS 49 CONTRAST 50 SHARPNESS 50 SATURATION 50 COLOR 0 BACK LIGHT 100 EXIT SELECT CVIDEO MOVE NTSC 60Hz/3.58MHz Adjust 1 BRIGHTNESS Increase or decrease the brightness. (Range : 0~100) 2 CONTRAST Increase or decrease the Contrast.
Setup Color temp 1 COLOR TEMP MODE LANGUAGE 50 GREEN 50 BLUE 50 2 2 OSD COLOR Adjust the OSD background from white opaque to half translucent. 3 OSD POSITION Change the osd position. (9 Positions) 4 DURATION Adjust time until the OSD Menu will disappear after adjusting the menu. (5, 10, 20, 30, 60, 90, 120, 180, 240 seconds) 5 RESET SETTINGS Changes the all OSD value to factory out going status. 6 AUTO SOURCE SELECT Disable of enable auto source select.
Standard Signal table Signal connector Pin Assignments PC Supported Mode VGA (15Pin D-Sub) Resolution Horizontal Frequency (KHz) Vertical Frequency (Hz) Clock Frequency (MHz) 640 X 350 @70Hz 31.469 70.087 25.175 720 X 400 @70Hz 31.469 70.082 28.324 640 X 480 @60Hz 31.469 59.940 25.175 640 X 480 @75Hz 37.500 75.000 31.500 800 X 600 @60Hz 37.879 60.317 40.000 800 X 600 @75Hz 46.875 75.000 49.500 1024 X 768 @60Hz 48.363 60.004 65.000 1024 X 768 @75Hz 60.023 75.029 78.
3 S-Video (BNC) RGBHV/RGBS/YPbPr (BNC) Pin No. 1 2 3 Assignment S-VIDEO/Y (Luma) S-VIDEO/C (Chroma) Ground 2 1 Pin No. 1 2 3 4 5 6 6 Assignment RGBS Y Pb Pr Red Pr Green Y Blue Pb H-Sync / C-Sync No Connection V-Sync No Connection Ground R/Pr 1 G/Y B/Pb 2 3 CS/HS 4 VS 5 RS232C (D-SUB 9Pin) Pin No. 1 2 3 4 5 6 Assignment No Connection TXD RXD No Connection Ground No Connection 7 8 No Connection No Connection 9 No Connection 1 OPTICAL 6 24 - English Pin No.
Specification Model LCD Panel Synchro nization FS-L2401D Type TFT-LCD Screen Size 24 linch Maximum Resolution 1920 X 1200 @ 60Hz Pixel pitch 0.270(H) mm X 0.270(V) mm Display Colors 16.
