AUTO - SCANNING WITH DIGITAL CONTROL LCD COLOR MONITOR FS-L1903C User manual (Rev.01) SMITHS HEIMANN www.smithsdetection.
Table of Contents Safety Instructions ......................................................................................... 5 Accessories ................................................................................................... 8 Power Connections ........................................................................................ 8 Monitor Connections ...................................................................................... 9 Mechanical Drawings ..............................
FCC INFORMATION This LCD monitor unit has been tested and found to comply with the limits of a Class B digital Device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against interference. This monitor can radiate radio frequency energy and, if not installed and used in accordance with the instructions, it may interfere with other radio communications equipment. There is no guarantee that interference will not occur in a particular installation.
Which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. E NVIRONMENTAL INFORMATION 1.
Safety Instructions On safety 1. Before connecting the AC power cord to the monitor, make sure the voltage designation of the AC voltage corresponds to the local electrical supply. 2. Never insert anything metallic into the cabinet openings of the Liquid Crystal Display (LCD) monitor. Doing so may create the danger of electric shock. 3. To reduce the risk of electric shock, do not remove cover. No user-serviceable parts inside. Only a qualified technician should open the case of the LCD monitor. 4.
Operator Safety Instructions For your safety, please read these safety instructions completely before you connect the equipment to the power source. The information in this summary is intended for operators. Carefully observe all warnings, precautions and instructions both on the Apparatus and in these operating instructions. Retain this manual for future reference.
If the provided plug does not fit into your outlet, consult an electrician. Never install cables, or any peripherals, without first unplugging the device from its power source. Servicing Do not attempt to service the apparatus yourself as opening or removing covers may expose you to dangerous voltages or other hazards, and will void the warranty. Refer all servicing to qualified service personnel.
Accessories AC Power cord (EU) VGA Cable Power Connections To the AC inlet connector 1) 2) 3) 4) AC Inlet AC ON/OFF Switch Use 220V or 110V Connect monitor to VGA source using VGA connector. Power on the monitor Done.
Monitor Connections ● AC IN: AC Inlet. ● ON/OFF: AC on/off switch. ● DVI: DVI Connection for Digital TMDS. ● VGA: 15Pin D-Sub connector for Analog RGB. ● RS-232C: 9Pin D-Sub connector for firmware update.
OSD Buttons Power LED Green: Normal mode Blink Green: Standby mode Blink Green: Soft power-off ● On-Screen Display (OSD) Function Button 1. POWER: Turns ON/OFF the monitor. 2. MENU: With OSD deactivated, Activate the OSD menu. With OSD activated, Exit from main menu or sub menu. 3. AUTO: Release the button (Auto Adjust): Fit to the most appropriate screen on the DSUB Analog signal.
Power Managements Status Normal Operation Sleep Mode LED Sign Green Green blink Power Consumption Normal Power < 1 Watt NOTE: Sleep mode will be entered by two conditions as below. Sleep mode is only available when sleep enable function in service menu is enabled. For default disabled, ask your service or administrator. 1) Entered by “soft-power switch” Turn off. 2) Entered by “Input H/V sync lost”.
2. RED Red balance (Only works with USER mode) (Range: 0~100) 3. GREEN Green balance (Only works with USER mode) (Range: 0~100) 4. BLUE Blue balance (Only works with USER mode) (Range: 0~100) IMAGE 1. IMAGE SIZE Change the image size (Fill aspect, 1:1, Full) 2. H POSITION Adjust the horizontal position of the displayed source image. (Range: 0~100) 3. V POSITION Adjust the vertical position of the displayed source image. (Range: 0~100) 4. SHARPNESS Set the sharpness of image (0 ~ 9) SETUP 1.
Prefer to use of LUMINANCE adjustment. 2. CONTRAST Increase or decrease the contrast (Range: 0~100) 3. LUMINANCE Adjust backlight dimming level (Range: 0~100) COLOR TEMP 1. MODE Change the color temperature mode (Range: 0~100) (C1 (Reddish, 6500K), C2 (Bluish, 9300K), USER) 2. RED Red balance (Only works with USER mode) (Range: 0~100) 3. GREEN Green balance (Only works with USER mode) (Range: 0~100) 4. BLUE Blue balance (Only works with USER mode) (Range: 0~100) IMAGE 1.
Signal Connector Pin Assignments Page | 14
Supported Signal Formats Standard Timing Tables Horizontal Resolution Vertical Period (uSec) Total (Pixel) Data Start (Pixel) Total (line) Data Start (line) 640 x 480 @ 59.9Hz 31.78 800 144 525 35 640 x 480 @ 75Hz 26.67 840 184 500 19 640 x 480 @ 85Hz 23.11 832 136 509 28 800 x 600 @ 56.3Hz 28.44 1024 200 625 24 800 x 600 @ 60.3Hz 26.40 1056 216 628 27 800 x 600 @ 72.2Hz 20.80 1040 184 666 29 800 x 600 @ 75Hz 21.33 1056 240 625 24 800 x 600 @ 85.1Hz 18.
Special Timing Tables Horizontal Vertical Period (uSec) Total (Pixel) Data Start (Pixel) Total (line) Data Start (line) 512 x 512 @ 71.1Hz 26.24 656 30 536 4 624 x 658 @ 74.9Hz 19.57 824 188 682 23 760 x 908 @ 80.1Hz 13.15 1002 233 950 41 808 x 802 @ 75Hz 15.98 1034 214 834 31 808 x 802 @ 87.8Hz 13.66 1034 214 834 31 880 x 658 @ 75Hz 19.56 1160 263 682 23 880 x 730 @ 75.1Hz 17.48 1126 233 762 31 880 x 946 @ 75Hz 13.
Horizontal Vertical Period (uSec) Total (Pixel) Data Start (Pixel) Total (line) Data Start (line) 1280 x 768 @ 75Hz 16.56 1696 336 805 34 1280 x 768 @ 85Hz 14.55 1712 352 809 38 1280 x 960 @ 60Hz 16.73 1696 336 996 33 1280 x 960 @ 60Hz 16.86 1440 112 988 25 1280 x 960 @ 75Hz 13.27 1728 360 1005 42 1280 x 960 @ 85Hz 11.64 1728 360 1011 48 1280 x 1024 @ 60Hz 15.63 1688 360 1066 41 1280 x 1024 @ 75Hz 12.50 1688 392 1066 41 1280 x 1024 @ 85Hz 10.
Specifications Model FS-L1903C Type DLM190-A01(Original : LM190E08) Size 19” Diagonal Resolution 1280 x 1024 Pixel pitch 0.63(H)mmX0.63(V)mm Display colors 16.7M (RGB 8-bit data) Contrast Ratio(Typ.) 800:1 Viewing Angle(Typ.) R/L 170, U/D 160 degree Luminance(Typ.) 300 cd/m Typical 35 Watt Standby Mode Under 1 Watt LCD PANEL Power Consumption Control Key Power Approval Marks Dimension 2 Input, Minus, Plus, Down, Up, Auto, Menu, Power AC 100-230V(50-60Hz) 1.
