IMPORTANT NOTE: Please read this owner’s manual in its entirety before operating this unit. Should you have any questions about our collars or their operation please contact our Customer Service department (see back page for address and phone number information). NOTICE! According to how you use your transmitter, the transmitting range might be much different. You will have more range if you use your transmitter apart from your body as follows: FCC/IC/CE COMPLIANCE Your R.A.P.T.
WARRANTY • D.T. Systems Premium Lifetime Warranty is the best warranty offered in the industry. This warranty is free to participating U.S. customers (a completed warranty registration card must be returned within 30 days of original purchase). This changes our normal one year parts and labor warranty to a limited lifetime warranty against manufacturing defects on parts and a one year warranty on labor.
INTRODUCTION IMPORTANT SAFETY NOTES Thank you for purchasing our Rapid Access Pro Trainer (R.A.P.T.TM) series remote training collar, the latest in ecollar technology and ergonomic design. The highlight of the system is the unique "hands-free" design of the remote transmitter - the new patented “Rapid AccessTM" total control button is easily accessible for instantaneous correction of your dog and our patented "SureGripTM" strap securely holds the unit in place - freeing up your hands for other activities.
MAINTENANCE It is very important to periodically clean your R.A.P.T. SeriesTM system for maximum performance. Regular cleaning will also lengthen the life of your unit. • Clean the collar box, belt and buckle with lukewarm water and a mild anti-bacterial soap. • Thoroughly clean the space between the electrodes and the belt. • Always allow the entire unit to completely dry before charging/using.
PARTS & FUNCTIONS SETTING THE INTENSITY LEVEL Setting the Jump Stimulation Level (cont.): Antenna Intensity Level Dial Rapid Access Button (default Nick Stim.) LED Indicator Light Continuous Stimulation Button Collar Selector Dial with Lockout 1. Press and hold Button Jump button. 2. While holding the Jump button, turn the Intensity Dial to the desired Jump stimulation level. The LED will start flashing to indicate that you are programming the Jump stimulation level 3. Release the Jump button.
SETTING THE INTENSITY LEVEL It is very important to set the correct intensity level on your R.A.P.T. Training System before beginning your training sessions to provide the proper level of stimulation without over-stimulating your dog. 1. Place the Intensity Selection dial so that the system is set on Level 1. 2. Turn on the Collar Receiver and then fit it properly around your dog’s neck. 3. Press the ‘Cont.’ button and check for a reaction.
PARTS & FUNCTIONS Vibration and Jump Buttons - Pressing the Vibration Button makes the collar vibrate only. Pressing the Jump Button makes the collar give a ‘Jump’ Stimulation, making the intensity level instantly “jump” to a user-programmed intensity level (see page 18). Magnetic ON/OFF Switch - White dot on Transmitter indicating location of the magnet used to power ON/ OFF the Collar Unit. Lanyard Connection - Point of attachment for lanyard.
PARTS & FUNCTIONS PROGRAMMING THE COLLAR When adding an “Add-On” collar, the collar will need to be programmed to the transmitter. If your current collar unit is not responding to the transmitter, it may also need to be reprogrammed to the transmitter. 1. Select the desired Collar Selecting Switch position on the transmitter. 2. Hold the Transmitter Magnet Indicator (white dot) directly against the Magnetic Activation Switch (small bump) on the right side of the Collar Receiver. 3.
PARTS & FUNCTIONS Collar Belt with MAXX-Range™ 360 Antenna - The embedded MAXX-Range™ Antenna is woven into the collar belt and runs along the entire length of the belt, providing extended range without the drawback of an external antenna. Because it wraps around the neck along with the collar belt, the MAXX-Range Antenna provides 360˚ degrees of signal reception and is not blocked by your dog’s body, regardless of which direction your dog is facing. Re-Thread SureGrip Strap 1.
TESTING SmartLED NOTE: If the collar unit is not responding to any signals R.A.P.T. Series collar units are equipped with the SmartLED battery status system. The SmartLED system lets you know when the unit is charging and when the charging is complete. It also gives you a status on how much charge is remaining in the battery during use, when it needs charging, and when the batteries will need to be replaced. from the transmitter, the collar may need to be reprogrammed to the transmitter (see page 16).
CHARGING THE BATTERIES TURNING ON AND OFF All R.A.P.T. Series TM collar units are equipped with rechargeable Nickel Metal Hydride (NiMH) batteries, which are not memory sensitive and do not require depletion before recharging. Although batteries come partially charged from the factory, it is recommended that they are given a full charge (about 12 hours) before initial use. The Transmitter is always in a permanent sleep state.