NOTICE! According to how you use your transmitter, the transmitting range might be much different. You will have more range if you use your transmitter apart from your body as follows: Maxi.
TABLE OF CONTENTS • Table of Contents "" • Introd ucti 0 n ." " • Package Contents "", • Model Features " .. " " " 3 " .. :." " . 4 " .. "." " "5 " .. """ .. 5 Parts & Functions """ 6 • Charging the Batteries """ 11 • Turning ON and OFF 12 • Testing 13 • Programming • Properly Fitti ng the Collar " ..
- INTRODUCTION Congratulations and thank you for purchasing our Micro-iDTTM PLUS Training Collar with Add-On capability. It offers the Maxx-Range ™ Internal Antenna System, the industry's only internally woven antenna in the collar. With up to a 900 yard range, they are perfect for use around the house and versatile enough to use out in the field. Micro-iDTTM PLUS series collars feature sixteen levels of intensity with an easy 'no-look' clicking intensity selection dial.
PACKAGE CONTENTS • Transmitter* • Collar Receiver • Rechargeable Batteries for the Collar (already installed in collar unit) • Battery Charger • Splitter/Adaptor Charging Cable • Test Light • Owner's Manual *9·volt transmitter battery not included MODEL FEATURES • Digital Technology • Up to 900 yard range • Expandable to 2- or 3~dog system with Micro-iOT Add-On coJlar units (sold separately) • Lightweight, compact collar and transmitter • 16 adjustable intensity levels of Momentary ('Nick') Stimulation and
· PARTS & FUNCTIONS Antenna _ LED Indicator Light Collar Selecting Switch I Intensity --Selection Dial Momentary "Nick" Stimulation Button Vibration Button- Continuous Stimulation Button Magnet Indicator.......
PARTS & FUNCTIONS Intensity Selection Dial The intensity selection dial can be set from level 1 to level 16 to find the exact stimulation level for your dog (see page 16). Transmitter Antenna Be sure to check that the antenna is securely fastened to the transmitter before each use. Handtightened only. Be careful when screwing the antenna into the transmitter. Over-tightening the antenna can cause damage to the antenna or the antenna mount.
- PARTS & FUNCTIONS Remote Training Buttons Pressing the "NICK" button will make the collar give a Momentary, or 'Nick' Stimulation. Pressing the "CONT" button gives a Continuous Stimulation. Pressing the red button on the left side will make the collar Vibrate only. Collar Selecting Switch Switching between collar units can be ~~-1 controlled by moving the toggle selection ~1fIiLIO;1DII switch to the desired unit.
PARTS & FUNCTIONS Collar Indicator Light When the Collar Receiver is turned on, the Red LED light will flash steadily once every two seconds to indicate that the unit is active. The Red LED light changes to a rapid flash when the battery is in need of charging. The Red LED light stays lit while plugged into the charger. Red Mark on the Collar Unit The Red Mark indicates the location of the Magnet Switch in the receiver. To l...-_:.:.....
- PARTS & FUNCTIONS Contacts Contacts should fit snugly against the dog's neck to ensure good contact with the skin. For more information on the proper fit of the collar, see page 15. Battery Charging Receptacles The battery charging receptacles are located on the side of the Collar Receiver. After charging, always close the jack with the rubber plug to prevent foreign particles from getting inside the unit. NOTE The unit is still waterproof even if water gets into the charging receptacle.
CHARGING THE BATTERIES Micro-iDTTM PLUS Series collars are equipped with rechargeable Nickel Metal Hydride (NiMH) batteries, which are not memory sensitive and do not require depletion before recharging. Although batteries come partially charged from the factory, it is recommended that tney are given a full charge (about 12 hours) before initial use. The transmitter uses a 9-volt replaceable battery (not included). Be sure to pay attention to the "+" and "-" charges when inserting the battery.
· TURNING ON AND OFF The Transmitter is always in a permanent sleep state. It is only ON when a button is being pressed and does not need to be turned off by the user. r----"Tl:I'l"I!~n Turning the Collar Unit On: Hold the Red Mark (Magnet Indicator) on the left side of the transmitter directly against the Red Mark (Magnetic Switch Indicator) on the front of the collar receiver. The Red LED Indicator will light solid for a second.
TESTING NOTE: Before testing, make sure that both units are fully charged and the power to the Collar Receiver is "ON". To Test the Electronic Stimulation: 1. Place the tester firmly on the contacts of the Collar Receiver. 2. Set the intensity (note - an intensity level setting of 4 or less might not be enough to light the tester). 3. Push the 'NICK' or 'CONT' button. 4.
· PROGRAMMING When adding an "Add-On" collar, the collar will need to be programmed to the transmitter. If your current collar unit is not responding to the transmitter, it may also need to be reprogrammed to the transmitter. 1. Select the desired Collar Selecting Switch position on the transmitter. 2. Hold the Red Mark (Magnet Indicator) on the Transmitter directly against the Red Mark (Magnetic Switch Indicator) on the front of the Coliar Receiver. 3.
PROPERLY FITTING TH E COLLAR NOTE: Proper collar tightness and position are very important to insure safe and consistent collar use. All electronic collars need to be very snug around the dog's neck to work properly. They must be just tight enough to allow the "contacts" or electrodes to make good contact on your dog's skin. If the collar is too loose, the stimulation may not work properly because good/consistent skin contact is not being achieved.
· SETTING THE INTENSITY LEVEL It is very important to set the correct intensity level on your Micro-iOT PLUS Training System before beginning your training sessions to provide the proper level of stimulation without over-stimulating your dog. 1. Place the Intensity Selection dial so that the system is set on Level 1. 2. Turn on the Collar and then fit it properly around your dog's neck. 3. Press either the 'NICK' or the 'CONT' Button and check for a reaction.
MAINTENANCE It is very important to periodically clean your MicroiDTTM PLUS Series systems for maximum performance. Regular cleaning will also lengthen the life of your unit. • Clean the Micro-iDTTM PLUS Series collar box with lukewarm water and a mild anti-bacterial soap. • Take care to thoroughly clean the space between the electrodes and the belt. • The belt and buckle should be cleaned with water and a mild soap then allowed to dry completely.
- IMPORTANT SAFETY NOTES • Before training, your dog should be examined by a veterinarian to assure that your dog is in good health. • Never leave your dog unattended with the unit on. Since no electronic device is perfect, there is a very slight possibility that your dog may receive an un intentional electric stimulation. • Your Micro-iDTTM PLUS Series training collar is a very valuable tool if used correctly.
WARRANTY All Micro-iDTTM PLUS Trainer systems have a one year parts and labor warranty, effective from the original date of purchase. A copy of the original sales receipt is required to validate the date of purchase. NOTE Warranty covers manufacturer's defects only. It does not cover damage caused by misuse or abuse. FCC COMPLIANCE Your Micro-iDTTM PLUS Trainer has been manufactured under complete compliance with the Federal Communication Commission (FCC).
D.T. Systems, Inc. 2872 Walnut Hill Lane Dallas, Texas 75229 Tel: (214) 350-9446, (888) 588-8364 Fax: (214) 350-7847 Website; www.dtsystems.com E-mail ;customerservice@dtsystems.com 1-iDT PLUS 2009.09.