SUPER TRAINERTM EZT SERIES D.T. Systems, Inc. 2872 Walnut Hill Lane Dallas, Texas 75229 Tel: (214) 350-9446, (888) LUV-U-DOG Fax: (214) 350-7847 Website: http://www.dtsystems.com E-mail: customerservice@dtsystems.com Electronic Dog Trainer Owner’s Manual • • • • • • • • EZT 1000 EZT 1002 EZT 1003 EZT 2000 EZT 2002 EZT 2003 EZT 3000 EZT 3002 D.T. SYSTEMS, INC.
Congratulations and Thank you for purchasing our EZT Super TrainerTM training collar. The EZT series represents the absolute latest technological advancement in the Electronic Dog Training World. It offers Maxx-Range™, the industry’s only internally woven antenna in the collar. With up to a 1,200 yard range, they are perfect for hunting, basic obedience and professional training. EZT series collars feature Sixteen levels of stimulation intensity, with an easy ‘no-look’ clicking stimulation dial.
TABLE OF CONTENTS WARRANTY How the Limited Lifetime Warranty works: • To qualify for the Warranty you must fill out the warranty registration card which came with your system and mail it (with your original sales receipt) to D.T. Systems within 30 days of purchase. • There is no charge for parts or labor for the first year on any of our lifetime warranted products.
FEATURES Every EZT Super TrainerTM Electronic Dog Training System Features: • Digital Technology • 1,200 Yard Range—(Over 2/3 mile) • Lightweight, Compact Collars (6.7 oz.) and • • • • • • • Transmitters (4.6 oz.) 16 Adjustable Intensity Levels Gentle Touch System™ Extra Mild Stimulation Maxx Range™ Invisible, Embedded Collar Antenna Built in Safety Shut-off Rechargeable Ni-MH Battery System.
IMPORTANT SAFETY NOTES CONT. • The electrodes on this collar are made with high grade stainless steel to help prevent any chemical or allergic reactions with your dog’s skin. • To prevent neck irritation, the collar should never be worn for more than 12 hours a day. Changing the collar location on the dog’s neck daily will also help prevent irritations. It is important to keep the collar clean. Clean the electrodes regularly with a mild anti-bacterial soap.
INDIVIDUAL MODEL FEATURES CONT. TESTING CONT. EZT 3000 and EZT 3002 To Test the Vibration: A) Follow the directions for testing the Electronic Stimulation, and press the button located on the west side of the transmitter. B) If you press the button on the East side of the transmitter, the unit should vibrate for .5 seconds and then the tester should light. If you press the button on the West, the unit should vibrate but the tester should not light.
ADJUSTING & POSITIONING YOUR COLLAR FOR PROPER FIT TESTING There are three methods you can use to test your EZT Super Trainer™ depending upon your model’s features. First, you should make sure that both units are fully charged. Then turn on the power to the collar receiver. Next, follow these steps: To Test the Electronic Stimulation: A) Place the tester firmly on the electrodes of the collar receiver.
PARTS & FUNCTIONS BATTERIES All EZT Super TrainerTM training collars are equipped with rechargeable Nickel Metal Hydride (NiMH) batteries. NiMH batteries are not memory sensitive and do not require depletion before recharging. The batteries come partially charged from the factory. It is, however, recommended that you give the battery a full charge before the first use. This takes about 12 hours. Remember - Always keep batteries away from flammable substances (especially when charging).
PARTS & FUNCTIONS CONT. PARTS & FUNCTIONS CONT. Remote Training EZT 2000 Series For the EZT 2000 Series, pressing the button located on the West side of the Transmitter causes the Collar Receiver to Vibrate. Pressing the button located on the East side of the Transmitter causes the Collar Receiver to Vibrate for .5 seconds. After .5 seconds, Continuous Stimulation will be applied simultaneously with the Positive Vibration.
INTENSITY LEVEL Intensity Selection Dial The intensity selection dial allows you to choose between sixteen different levels of stimulation, allowing for very precise control. TRAINING INTENSITY LEVEL PARTS & FUNCTIONS CONT. Transmitter Indicator Light When one of the push button switches on the transmitter are pushed, the RED light will turn on to indicate that the transmitter is being operated.
