I 3 NOTICE! According to how you use your transmitter, the transmitting range might be much different.
TABLE OF CONTENTS Table of Contents ....... Introduction . . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . ............ Individual Model Features . . . . Package Contents Adjusting and Positioning Your Collar for Proper Fit . . . Parts and Functions 7 .... Turning ON and OFF 8 10 ... ............. Remote Training Buttons . . . . . . . . . Intensity Levels Switching Between Collars (Two Dog) .......... Batteries . . . . . . . . . . . . . . . . Testing . . . . . . . . . . . .
Congratulations and thank you for purchasing one of our SUPER PRO @LITETM dog training systems. The SPT series represents the absolute latest technological advancement in the Electronic Dog Training World. They offer compact, lightweight collar receivers which include completely internal antenna systems. The convenient, one-touch Digital Transmitters are lightweight and feature an LCD display which allows for extreme ease of use.
IMPORTANT NOTE Please read this owner's manual in its entirety before attempting to operate this unit. Should you have any questions about our collars or their operation please contact our Customer Service Department (see last page for contact information). Every SUPER PRO BLITETMElectronic Dog Training System Features: LCD display on transmitter One touch digital controls Lightweight, compact collars and transmitters (8 oz.
SPT 2420 and SPT 2422 The SPT 2420 features Momentary (Nick) Stimulation, Continuous Stimulation, Jump Stimulation (patent pending), Rise Stimulation (patent pending) and Positive Vibration. The SPT 2422 has the same features as the SPT 2420 and comes with two Collar Receiver units (orange and black) which are operated fiom the same transmitter. You can switch from one collar to the other by pressing the Collar Selection button on the transmitter.
ADJUSTING& POSlTlONlNG YOUR COLLAR FOR PROPER FIT position are very important to insure safety and correct functioning every time you All electronic collars need to be very snug to work properly. They must be just tight enough to allow the "prongs" or electrodes to make good skin contact. Lf your collar is too loose, the stimulation may not work properly because good skin contact is not being achieved.
PARTS & FUNCTIONS Antenna--+ RunlPoinP --1 Vibration ---1 I /1 ~ick Stimulation T I Stimulation Continuous Stimulation * 2-dog models only * SPT 243012432only \ Rise Stimulation - -- Charging Receptacle Transmitter (SPT 2430 shown, models may vary slightly)
PARTS & FUNCTIONS CONT.
I TURNING YOUR UNIT ON & OFF Turning the Unit On: Press and hold the Power button on the Collar Receiver. The red LED will flash for approximately 7 seconds. You may release the Power button at any time while the red LED is flashing. The unit is now ON. The LED indicator will now flash approximately every 2 seconds. (Note: You can turn on the Transmitter by pressing any button on the transmitter. When the transmitter is turned on, the backlight will light for 5 seconds and then go into power save mode.
The first and most important step in training your dog with your SPT Training System is the determination of the correct Intensity Level to provide the proper training stimulation without over stimulating your dog. To do this, place the collar ON and place it on the dog's neck. Press the Intensity Level Adjustment Down button until the LCD display shows that the system is set on level 1. Press either the "NICK"' or the "STIMU." button.
Using the Rise Stimulation The Rise function will gradually increase stimulation from your current intensity level to the maximum intensity level (level 50) while the "RISE button is being pressed. The intensity level will return to its original setting when the button is released. Setting the Jump Level 1. Press and hold both the "JUMP" button and one of the Intensity Level Buttons at the same time ("Intensity Up" button for increase, "Intensity Down" button for decrease). 2.
A REMOTE TRAINING BUTTONS Your SPT 2400 series collar has four control buttons on the front of the transmitter and up to three buttons on the left side of the transmitter (1 button on SPT 2420 and 2422 models, 3 buttons on SPT 2430 and 2432 models). Pressing the "NICK" button applies a very quick stimulation. Pressing the "STIMU." or constant stimulation button applies a continuous stimulation for up to 8 seconds. ressing the "JUMP" button causes the collar to apply a Jump stimulation.
- ..-----., --- ..---, -------(TWO DOG MODELS) fl With SPT Two Dog Systems (2422 & 2432) you can control two dogs with one transmitter. The LCD display shows whether you are currently controlling the Orange Collar Receiver (ORG) or the Black Collar Receiver (BLK). To switch the currently active collar, simply press the Collar Selection button (marked "O/B"). The SPT 2430 and 2432 models also feature a beeper with Locate, R M o i n t , and Point Only modes. 1.
I with rechargeable Nickel-Metal Hydride (NiMH) batteries which are not memory sensitive and do not require depletion before recharging. When the battery is running low in the transmitter, the backlight will flash 15 times for 5 seconds to alert you of this status. The collar unit will flash its red LED 3 times every 2 seconds when its battery is low. The batteries come partially charged from the factory, but will require a full charge before the fnst use (12 hours).
There are two or three methods you can use to test your SUPER PRO @LITETRAINERTM depending upon your model's features. First, you should make sure that both the transmitter and receiver are hlly charged. Then, turn on the power to the Collar Receiver. Next, follow one of these three steps: To Test the Electronic Stimulation: A) Place the tester firmly on the electrodes of the Collar Receiver. B) Set the intensity (Note - An intensity level setting of 7 or less might not be enough to light the tester).
lo lest the Vibration: A) Press the VIBRATION button (bottom button on left side of transmitter). B) When you press the VIBRATION button the unit should vibrate but the tester should not light. To Test the Beeper: (SPT 2430 and 2432 only) A) Press the LOCATE button (top button on left side of transmitter). The collar should beep anytime this button is pressed B) Press the RunIPoint Mode button (middle button on left side of transmitter). The unit is now in the Run and Point Mode.
Press and hold the Power button on the Collar Receiver. The red LED light on the collar will flash 7 times and then stay on solid. You must hold down the power button until the LED light becomes solid. Simultaneously press and release the "NICK and "STIMU." buttons. In a few seconds, you will see the LED light blink 3 times. The collar ID is now programmed, and the collar receiver is now ON. It is very important to periodically clean your SUPER P R O @UTETRAINERTMfor maximum performance.
Before beginning training your dog should be examined by a veterinarian to assure that there are no physical reasons for your dog's excessive barking and to assure that your dog in good health. Your SUPER PRO @UTETRIUNERTMis a very valuable tool if used correctly. Therefore, it is extremely important that you completely understand all functions of the collar and how to properly train with it before placing it on your dog.
I WARRANTY D.T. Systems Premium Lifetime Warranty is the best warranty offered in the industry. This warranty is free to participating U.S. customers. (The warranty registration card must be returned within 30 days of original purchase). This changes our normal one year parts and labor warranty to a lifetime warranty against manufacturing defects on parts and a one year warranty on labor. What is covered: D.T.
I W A K K A N 1 Y (LVN I.) n u w me umlceu LlIwlme warranxy worm: ' I - To qualify for the Warranty you must fill out the warranty registration card which came with your system and mail it (with your original sales receipt) to D.T. Systems within 30 days of purchase. - There is no charge for parts or labor for the first year on any of our lifetime warranty products.
I FCC COMPLIANCE Your SUPER PRO @LITETRAINERm has been manufactured under complete compliance with the Federal Communication Commission (FCC). The complex internal structure of each product has been designed to operate within specific regulations of FCC specifications. Any unauthorized modifications to your product is a violation of these specifications. The SUPER PRO @UTETRAINERm has been made with State of the Art equipment. Any fine adjustment should be performed only by D.T. Systems' technicians.
2872 Walnut Hill Lane Dallas, Texas 75229 Tel: (2 14) 350-9446, (888) LUV-U-DOG Fax: (214) 350-7847 Website: http://www.dt~y~tern~.~~m E-mail: customerservice@dtsystems.
