SUPER TRAINER TM Micro-iDT™ SERIES Electronic Dog Trainer Owner’s Manual • Micro-iDT™ Z3000 (One Dog Trainer) • Micro-iDT™ Z3002 (Two Dog Trainer) • Micro-iDT™ Z3003 (Three Dog Trainer)
TABLE OF CONTENTS • Table of Contents......................................... 3 • Introduction.................................................. 4 • Package Contents ......................................... 5 • Model Features............................................. 6 • Adjusting and Positioning Your Collar for Proper Fit............................ 7 • Parts and Functions ...................................... 8 • Turning ON and OFF................................... 13 • Batteries ...
INTRODUCTION Congratulations and thank you for purchasing our Micro-iDT™ Training Collar. The Micro-iDT™ series represents the absolute latest technological advancement in the Electronic Dog Training World. It offers Maxx-Range™, the industry’s only internally woven antenna in the collar. With up to a 900 yard range, they are perfect for field or household use. Micro-iDT™ series collars feature Sixteen levels of stimulation intensity, with an easy ‘no-look’ clicking intensity selection dial.
PACKAGE CONTENTS • Transmitter • Collar Receiver (1-for Micro-iDT™ Z3000, 2-for Micro-iDT™ Z3002, 3-for Micro-iDT™ Z3003) • Rechargeable Batteries for the Collar (already installed in collar unit) • Battery Charger • Charging Cable • Test Light • Owner’s Manual • TX battery not included IMPORTANT NOTE: Please read this owner’s manual in its entirety before operating this unit.
MODEL FEATURES Every Micro-iDT™ Electronic Dog Training System Features: • • • • • • • • • • • • • Digital Technology Up to 900 yard range Lightweight, compact collar and transmitter 16 adjustable intensity levels of Momentary (‘Nick’) Stimulation and Constant Stimulation Positive Vibration Gentle Touch System™ Extra Mild Stimulation MAXX-Range™ Invisible, Embedded Collar Antenna Built in safety shut-off Rechargeable Ni-MH battery system in collar Completely waterproof collars Weather resistant transmitter
ADJUSTING & POSITIONING YOUR COLLAR FOR PROPER FIT Proper collar tightness and position are very important to insure safety and correct functioning every time you use the collar. • All electronic collars need to fit very snugly to work properly. They must be just tight enough to allow the “prongs” or electrodes to make good skin contact. In most cases, you should be able to fit no more than two fingers between the collar belt and your dog’s neck.
PARTS & FUNCTIONS Antenna Toggle Switch (multiple dog units only) Intensity Selection Dial LED Indicator Light Momentary “Nick” Stimulation Button Vibration Button Constant Stimulation Button Magnet Indicator (Red Mark) Model Number Transmitter (Micro-iDT Z3002 shown) 8
PARTS & FUNCTIONS CONT. Intensity Selection Dial The intensity selection dial allows you to choose between sixteen different levels of stimulation for very precise control. Selecting Proper Intensity Level The first and most important step in training your dog with your Micro-iDT™ Training System is determining the correct Intensity Level to provide the proper training stimulation without over-shocking your dog. To do this, turn the Collar Unit ON and properly place it on the dog’s neck.
PARTS & FUNCTIONS CONT. Magnet Indicator (Red Mark) The RED mark indicates the location of the magnet in the transmitter. The indicator is used to turn the receiver ON/OFF and for ID programming. Transmitter Indicator Light When any of the buttons on the transmitter is pushed, the RED light will turn on to indicate that the transmitter is being operated. When the battery is low, the RED light will flash rapidly.
PARTS & FUNCTIONS CONT. Collar Belt with Embedded Receiver Antenna Electrodes Red Mark (Magnetic Switch Indicator) Battery Charging Receptacle LED Indicator Light Collar Receiver Collar LED Indicator Light The red LED light on the collar unit will flash to indicate the unit is ON. When the battery in the collar unit has a sufficient charge, the red LED light will flash about once every two seconds while the unit is ON.
PARTS & FUNCTIONS CONT. Electrodes Electrodes should fit snugly on the dog’s neck to ensure good contact with the skin. For more information on the proper fit of the collar, see page 7. Collar Belt with Embedded Receiver Antenna The embedded collar antenna is woven into the collar belt, and runs the along the entire length of the belt. WARNING Do not cut the collar belt. Doing so will damage the antenna and may result in severely decreased receiver range.
TURNING THE UNIT ON AND OFF 1. 2. 3. 4. 1. 2. 3. 4. Turning the Collar Unit ON Hold the Red Mark (Magnet Indicator) on the left side of the transmitter directly against the Red Mark (Magnetic Switch Indicator) on the front of the collar receiver. A small red LED light inside the Collar Unit will light up solid for about 1 second, and then will begin to flash. You may remove the Transmitter away from the Collar Unit as soon as the LED light starts flashing The Collar Unit is now ON.
BATTERIES All Micro-iDT™ training collars are equipped with rechargeable Nickel Metal Hydride (NiMH) batteries. NiMH batteries are not memory sensitive and do not require depletion before recharging. The batteries come partially charged from the factory. It is, however, recommended that you give the battery a full charge before the first use. This takes about 12 hours. Remember - Always keep batteries away from flammable substances (especially when charging).
TESTING Before testing, make sure that the collar unit is fully charged and the power to the Collar Receiver is “ON”. To Test the Electronic Stimulation: 1. Place the tester firmly on the Collar Unit electrodes as shown. 2. Set the intensity level (a setting of 4 or less may not light the tester due to its low intensity level). 3. Push either the ‘NICK’ or ‘CONT’ button. 4.
REPROGRAMMING If you own a multiple dog unit, you must select the collar that is being programmed on the Collar Selecting Switch before starting this procedure. 1. Hold the Red Mark (Magnet Indicator) on the left side of the Transmitter directly against the Red Mark (Magnetic Switch Indicator) on the front of the Collar Receiver. 2. A small red light inside the Collar Receiver will light up solid for about 1 second, followed by 6 flashes.
IMPORTANT SAFETY NOTES • Before you start training, your dog should be examined by a veterinarian to assure that your dog is in good health. • Never leave your dog unattended with the unit on. Since no electronic device is perfect, there is a very slight possibility that your dog may receive an unintentional electric stimulation. Micro-iDT™ Trainer is a very valuable tool if used correctly.
MAINTENANCE • It is very important to periodically clean your Micro-iDT™ Trainer for maximum performance. Regular cleaning will also lengthen the life of your unit. • Clean the Micro-iDT™ Trainer collar box with lukewarm water and a mild anti-bacterial soap. • Take care to thoroughly clean the space between the electrodes and the belt. • The belt and buckle should be cleaned with water and a mild soap then allowed to dry completely.
WARRANTY All Micro-iDT™ Trainer collars have a one year parts and labor warranty, effective from the original date of purchase. A copy of the original sales receipt is required to validate the date of purchase. NOTE Micro-iDT™ Trainer batteries are not covered under the warranty. FCC COMPLIANCE Your Micro-iDT™ Trainer has been manufactured under complete compliance with the Federal Communication Commission (FCC).
2872 Walnut Hill Lane Dallas, Texas 75229 Tel: (214) 350-9446, (888) LUV-U-DOG Fax: (214) 350-7847 Website: http://www.dtsystems.com E-mail: customerservice@dtsystems.com 6-iDT-3000 2007.08.
