D.T.S. Illuminazione srl Via Fagnano Selve 10/12/14 47843 Misano Adriatico (RN) ITALIA Tel +39 0541 611131 Fax +39 0541 611111 Made in Italy info@dts-lighting.it http://www.dts-lighting.
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso scritto della D.T.S . D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di design a ciascun proprio prodotto. D.T.
INDEX: 1- SYMBOLS 2- GENERAL WARNING 3- GENERAL WARRANTY CONDITION 4- TECHNICAL FEATURES 5- ACCESSORIES 6- IMPORTANT SAFETY INFORMATION 6.1 Fire prevention 6.2 Prevention of electric shock 6.3 Protection against ultraviolet radiation 6.4 Safety 6.5 Level of protection against the penetration of solid and liquid objects 7- MOUNTING / REPLACING THE LAMP AND LAMP ALIGNMENT 8- VOLTAGE AND FREQUENCY 9- INSTALLATION 9.1 Safety cable 9.2 Protection against liquids 9.3 Movement 9.4 Risk of fire 9.
1- SYMBOLS Graphic symbols used on this manual THIS SYMBOL INDICATES A HOT SURFACE THIS SYMBOL INDICATES ELECTRIC SHOCK RISK ! F THIS SYMBOL INDICATES GENERAL RISK THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON INFLAMMABLE SURFACES” UV THIS SYMBOL MEANS “RADIATION FROM THIS LAMP CAN CAUSE DAMAGE TO EYES AND SKIN” 2M THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT 2- GENERAL WARNING Read the instruction contained in this user manual carefully, as they giv
4- TECHNICAL FEATURES The JACK is a high-power, compact, lightweight moving head. JACK features a wide excursion motorized zoom allowing any application from long-throw projections to large wall washing. Beam opening is: 1° - 2,5° 'Beam' projection; 2,5° - 37° 'Spot' projection; 38° - 46° 'Wash' projection. JACK generates a huge luminosity and extremely uniform projection using only a 189 W lamp; power consumption is just 230W.
4- TECHNICAL FEATURES Interface / Control / Programming * LCD graphic display (control / management / monitoring of the main parameters) * 4 soft-keys (control / management / monitoring of the main parameters) * Controlled via DMX 512 standard digital communication protocol * RDM * ARTNET (available on request) * Wireless ready * Internal operating system updatable via D.T.S.
4- TECHNICAL FEATURES Dimensions Packaging Dimensions (LxWxH) Unit Dimensions (LxWxH) 532 x 430 x 414 mm 350x370x560mm Weight: 14,4 Kg Weight: 11,9 Kg 5- ACCESSORIES 370 mm 270° 470 mm 560 mm 350 mm 217 mm 300 mm As standard * 1 x MSD Platinum 5R 189W (cod. 0505S034) * 1 x powerCON male cable connector (cod. 0520P014) * 1 x XLR 5 Pins male cable connector (cod. 0508B028) * 1 x XLR 5 Pins female cable connector (cod.
6- IMPORTANT SAFETY INFORMATION 6.1 Fire prevention: JACK uses a MSD Platinum 5R 189W lamp. The use of any other alternative lamp is not recommended and will null and void the fixture's warranty. -Never locate the fixture on any flammable surface. -Minimum distance from flammable materials: 1 MT. F -Minimum distance from the closest illuminable surface: 2 MT. 2M -Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if there is any doubt.
7- MOUNTING / REPLACING THE LAMP AND LAMP ALIGNMENT Warning: Switch off the unit before replacing the lamp. MSD Platinum 5R Power 189W Luminous flux 7950 lm Colour temperature 8.000°K Type of connection: PINS 2,8 x 0,8 mm Rated life 2000 hours 1) Loosen the 2 “¼ turn” screws which fix the head covers (photo 1) . 2) Once loosen the screws, simply lift the covers to access the internal components (photo 2 and 3).
Photo 6 4) Loose the four screws which fix the lamp (photo 7), unplug the two fast-on cable connectors (photo 8) and remove the old lamp. 5) Put in place the new lamp and push it toward the three mechanical ends D, E, F (photo 9) on the lamp support; this let you have the lamp properly aligned on the optical system. Photo 7 Photo 8 D E UV WARNING: Never look directly at the lamp when it‟s lit. Discharge lamps emits UV rays; radiation from this lamp can cause damage to eyes and skin.
8- VOLTAGE AND FREQUENCY The JACK with electronic ballast can operate at 90-260 VOLT 50 or 60 Hz. 9- INSTALLATION JACK may be either floor or ceiling mounted. For floor mounting installations, the JACK is supplied with four rubber mounting feet on the base. For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the mounting surface.
9.2 Protection against liquids The projector contains electric and electronic components which should under no circumstances come into contact with oil, water or any other liquid. The proper unit functioning would be compromised should this occur. 9.3- Movement JACK FPR (Cod. 03.MS012.EBLFP) Unlimited Pan rotation; Tilt 270° (1,5 sec.) JACK (Cod. 03.MS012.EB.L) Pan 540° (2,5 sec.), Tilt 270° (1,5 sec.) DO NOT place any obstructions in the path of the projector's movement.
10- MAINS CONNECTION JACK with electronic ballast operate at 90-260 VOLT 50-60 Hz. Prior to connecting the unit to your mains supply, ensure that the model in your possession correctly matches the mains supply available. For connection purposes, ensure that your plug is capable of supporting 1,5 amps at 230 VOLT, or 3 amps at 90 VOLT. Strict adherence to regulatory norms is strongly recommended. MAINS AC OUTPUT 90-260V 50/60 Hz (16A Max) MAX 12 JACK UNITS @ 230V MAX 6 JACK UNITS @ 120V (Cod. 03.
11- DMX SIGNAL CONNECTION The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector. Ensure that the conductors do not touch each other. Do not connect the cable ground to the XLR chassy. The plug housing must be isolated.
11.1-DMX Addresses JACK can be used in 2 different DMX modes: 25 DMX control channels (Default) or 17 DMX control channels. Here below is described the DMX channels addressing for the controller when JACK is set to 25 and 17 DMX control channels: 25 channels mode (Default) Projector 1 A001 Projector 2 A026 If you want to select the next projector, just add “25” Projector 3 ….. projector 6 A051 A…. A126 17 channels mode Projector 1 A001 Projector 2 A018 Projector 3 …..
13- DISPLAY FUNCTIONS 2dBi IP20 omnid. antenna DISPLAY WIRELESS DMX RECEIVER RETROFIT 03.LA.126 MENU UP DOWN ENTER DMX IN DMX OUT Available only for units with FPR on board DMX OUT MAINS AC OUTPUT 90-260V 50 / 60 Hz (16A Max) DMX IN 03.MS012.EBLFP 03.MS012.EB.L DMX IN DMX OUT MAINS AC INPUT 90-260V 50 / 60Hz DISPLAY FUNCTIONS The JACK display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions.
13- DISPLAY FUNCTIONS Software Version: 47.35 PS: on software version 47.35, has been added a new function called “ZERO SKIP”. “ZERO SKIP” function can be activated by pressing at the same time the “MENU” + “UP” buttons on unit display during initial reset. This function let you have the unit display ON and internal motors (Pan&Tilt + head motors) OFF. Usefull when the unit is still in the flight case and DMX address or internal unit parameters need to be set.
13- DISPLAY FUNCTIONS Menu Up-Down Display ENTER Up-Down DISPLAY Display Flip ON THE GROUND (Default) SUSPENDED DISPLAY FLIP / STAND BY / CONTRAST FLIP Display Flip: Reverses display's reading depending on the mounting position (On the ground or suspended). ON THE GROUND Display Standby: To turn off the display (after 5 seconds) or leave it always on.
13- DISPLAY FUNCTIONS Menu Up-Down Base Fans ENTER Up-Down BASE FANS Base Fans speed control BASE FANS 1=13V 4 12=24V MENU ENTER DOWN Menu Up-Down Lamp Fans ENTER Up-Down 12=24V Up-Down Gobo Rotation ENTER Up-Down GOBO ROTATION Auto Focus ENTER Up-Down AUTO FOCUS MENU ENTER DOWN Up-Down System info ENTER Up-Down Up-Down Reserved RESERVED (Code = 100) Pan lock-Tilt lock Pan free-Tilt free Lock Detector System Reboot Exit To Main ENTER STRIKE:045 MENU ENTER DOWN Up-Dow
LOCK DETECTOR OFF MENU ENTER DOWN UP REBOOT MENU ENTER DOWN UP EXIT TO MAIN Lock Detector OFF = Default Lock Detector ON : This function let the user to activate the Lock detector on Pan and Tilt.
14- ERROR MESSAGES ERROR ERROR ERROR COLOUR WHEEL PAN TILT MENU ENTER DOWN UP MENU ENTER DOWN UP PAN REPOSITIONING ENCODER ERROR COLOUR WHEEL POSITION ERROR MENU ENTER DOWN UP TILT REPOSITIONING ENCODER ERROR ERROR ERROR ERROR ERROR INTERNAL BUS DMX ADDRESS GOBO GOBO INDEX MENU ENTER DOWN UP COMMUNICATION PROBLEM BETWEEN 9 MOTORS CARD AND PAN&TILT CARD MENU ENTER DOWN UP DMX ADDRESS ERROR MENU ENTER DOWN UP GOBO WHEEL ERROR MENU ENTER DOWN GOBO POSITION ERROR ERROR ER
15- HIDDEN MENU For technical personnel only. To operate this menu: -Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED) -Reset the JACK (reset from the MENU, not from the DMX controller!). -While reset is running, press the MENU and ENTER keys at the same time. CALIBRATION DEFAULT CAL. MOTORS ALIGNMENT SET ALL MOTORS AT 128 PAN UP MIN SHUTT.POW.
15.
18- OPENING THE PROJECTOR HOUSING It is possible to inspect the inside of the projector by removing the cover as indicated below. ATTENTION REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR‟S INTERNAL COMPONENTS. 1) Loosen the 2 screws which fix the head covers (photo 1) . 2) Once unscrewed, simply lift the covers to access the internal components (photo 2 and 3).
Coated side When an object is held up the coated side of the glass gobo there is no space between the object and its reflection. Coated side Uncoated side When an object is held up the uncoated side of the glass gobo there is a space between the object and its reflection. Uncoated side Load with coated surface toward the light source. Replacing gobos on the rotating gobo wheel When replacing gobos, ensure that the projector is switched off. 1) Open the projector housing as described on page 23.
21- PERIODIC CONTROLS Attention ! Disconnect mains power prior to removing the projector housing. Lamp UV The lamp should be replaced if there is any visible damage or deformation due to heat. This will help to avoid the danger of the lamp exploding. JACK lamp lifespan is about 2000 hours, then it is necessary to replace it. Mechanical parts Periodically check all mechanical parts, gears, guides, belts, etc. for wear and tear, replacing them if necessary.
22- DMX PROTOCOL 25 CHANNELS MODE (DEFAULT) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 PAN msb PAN lsb TILT msb TILT lsb SPEED MOVEMENT PAN FAR (Active only on Jack FPR Cod. 03.MS012.
DMX CHANNEL DMX value 000-010 011-020 021-030 031-040 041-050 051-060 061-070 071-080 081-090 091-100 101-110 111-120 121-182 183-193 194-255 DMX CHANNEL DMX value 000-007 008-255 DMX CHANNEL DMX value 000-019 020-039 040-059 060-079 080-089 090-099 100-109 110-119 120-129 130-139 140-149 150-159 160-169 170-179 180-189 190-199 200-209 210-219 220-227 228-233 234-255 6 Parameter: PAN FAR (Active only on Jack FPR Cod. 03.MS012.
DMX CHANNEL 9 Parameter: COLOUR IF CHANNEL 10 = FULL COLOUR (DMX range value 0-63) DMX value Function 000-013 Colour 1 014-027 Colour 2 028-041 Colour 3 042-055 Colour 4 056-069 Colour 5 070-083 Colour 6 084-097 Colour 7 098-111 Colour 8 112-125 Colour 9 126-139 Colour 10 140-153 Colour 11 154-167 Colour 12 168-181 Colour 13 182-195 Colour 14 196-209 Colour 15 210-223 Colour 16 224-237 Colour 17 238-255 Colour 18 IF CHANNEL 10 = HALF COLOUR (DMX range value 64-127) DMX value Function 000-012 Colour 1 01
DMX CHANNEL DMX value 000-020 021-041 042-062 063-083 084-104 105-125 126-146 147-167 168-188 189-207 208-213 214-219 220-225 226-231 232-237 238-243 244-249 250-255 DMX CHANNEL DMX value 000-127 128-255 11 Parameter: GOBO Function Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Gobo 8 Gobo 9 Speed rotation 1 min Speed rotation 2 Speed rotation 3 Speed rotation 4 Speed rotation 5 Speed rotation 6 Speed rotation 7 Speed rotation 8 max 12 Parameter: GOBO MODE Function Gobo Rotation Mode Gobo
DMX CHANNEL DMX value 000-009 010-022 023-035 036-048 049-061 062-074 075-087 088-100 101-113 114-126 127-138 139-151 152-164 165-177 178-190 191-203 204-216 217-229 230-242 243-255 DMX CHANNEL DMX value 000-018 019-037 038-056 057-075 076-094 095-113 114-132 133-151 152-170 171-189 190-207 208-213 214-219 220-225 226-231 232-237 238-243 244-255 15 Parameter: GOBO SHAKE Function Stop Gobo shake R-L speed 1 Gobo shake R-L speed 2 Gobo shake R-L speed 3 Gobo shake R-L speed 4 Gobo shake R-L speed 5 Go
DMX CHANNEL DMX value 000-009 010-022 023-035 036-048 049-061 062-074 075-087 088-100 101-113 114-126 127-138 139-151 152-164 165-177 178-190 191-203 204-216 217-229 230-242 243-255 DMX CHANNEL DMX value 000-009 010-246 247-255 DMX CHANNEL 17 Parameter: FIXED GOBO SHAKE Function Stop Gobo shake R-L speed 1 Gobo shake R-L speed 2 Gobo shake R-L speed 3 Gobo shake R-L speed 4 Gobo shake R-L speed 5 Gobo shake R-L speed 6 Gobo shake R-L speed 7 Gobo shake R-L speed 8 Gobo shake R-L speed 9 Stop Gobo s
IF CHANNEL 20 = SPOT MACROS (DMX range value 192-255) SPOT Macros not yet implemented DMX value Function 000-009 No effect 010-063 SPOT macros 1 064-117 SPOT macros 2 118-171 SPOT macros 3 172-213 SPOT macros 4 214-255 SPOT macros 5 DMX CHANNEL DMX value 000-063 064-127 128-191 192-255 DMX CHANNEL DMX value 000-127 128-255 DMX CHANNEL DMX value 000-255 DMX CHANNEL DMX value 000-255 DMX CHANNEL DMX value 000-255 DMX CHANNEL DMX value 000-009 010-060 061-129 130-179 180-200 201-239 240-255 20 Para
22- DMX PROTOCOL 17 CHANNELS MODE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PAN msb PAN lsb TILT msb TILT lsb SPEED MOVEMENT PAN FAR (Active only on Jack FPR Cod. 03.MS012.
DMX CHANNEL DMX value 000-010 011-020 021-030 031-040 041-050 051-060 061-070 071-080 081-090 091-100 101-110 111-120 121-182 183-193 194-255 DMX CHANNEL DMX value 000-007 008-255 DMX CHANNEL DMX value 000-019 020-039 040-059 060-079 080-089 090-099 100-109 110-119 120-129 130-139 140-149 150-159 160-169 170-179 180-189 190-199 200-209 210-219 220-227 228-233 234-255 6 Parameter: PAN FAR (Active only on Jack FPR Cod. 03.MS012.
DMX CHANNEL DMX value 000-004 005-009 010-014 015-019 020-024 025-029 030-034 035-039 040-044 045-049 050-054 055-059 060-064 065-069 070-074 075-079 080-084 085-089 090-094 095-099 100-104 105-109 110-114 115-119 120-124 125-129 130-134 135-139 140-144 145-149 150-154 155-159 160-164 165-169 170-174 175-197 198-200 201-203 204-206 207-209 210-212 213-215 216-218 219-221 222-224 225-228 229-231 232-234 235-237 238-240 241-243 244-246 247-249 250-252 253-255 9 Parameter: COLOUR Function Colour 1 Colou
DMX CHANNEL DMX value 000-020 021-041 042-062 063-083 084-104 105-125 126-146 147-167 168-188 189-207 208-213 214-219 220-225 226-231 232-237 238-243 244-249 250-255 DMX CHANNEL DMX value 000-127 128-180 181-202 203-255 DMX CHANNEL DMX value 000-018 019-037 038-056 057-075 076-094 095-113 114-132 133-151 152-170 171-189 190-207 208-213 214-219 220-225 226-231 232-237 238-243 244-255 10 Parameter: GOBO Function Open Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Gobo 8 Gobo 9 Speed rotation 1 min
DMX CHANNEL DMX value 000-009 010-124 125-132 133-159 160-186 187-213 214-234 235-255 DMX CHANNEL DMX value 000-127 128-255 DMX CHANNEL DMX value 000-255 DMX CHANNEL DMX value 000-255 DMX CHANNEL DMX value 000-009 010-060 061-129 130-179 180-200 201-239 240-255 13 Parameter: IRIS Function Open Linear Iris from open to closed Closed Iris pulse at different speed from min to max Iris pulse with flash closing from min to max Iris pulse with flash opening from min to max Iris pulse with flash closing
23- 9 MOTORS CONTROL CARD D.T.S.
24- PAN & TILT CARD D.T.S.
25- DISPLAY CARD D.T.S. Code: 0514T024 FROM PAN&TILT CARD 0514T022 J14 26- LAMP ON-OFF CONTROL CARD FANS To ELECTRONIC BALLAST BOARD EUC 185d X2 From PAN&TILT CARD 0514T022 J13 / J12 D.T.S.
27- ROTATING GOBO WHEEL GOBO 1 DICRO RAYS GOBO 2 DICRO VERTIGO GOBO 3 DICRO VERBENA GOBO 4 DICRO PINWHEEL GOBO 5 DICRO DAISY D.T.S. Code: 0516G054 D.T.S. Code: 0516G055 D.T.S. Code: 0516G056 D.T.S. Code: 0516G057 D.T.S. Code: 0516G058 GOBO 6 DICRO PIE SLICES GOBO 7 DICRO SQUARE GOBO 8 DICRO WAVE GOBO 9 DICRO TRIANGLE D.T.S. Code: 0516G059 D.T.S. Code: 0516G060 D.T.S. Code: 0516G061 D.T.S. Code: 0516G062 28- ROTATING GOBO PROVIDED INTO THE UNIT BOX GOBO 10 DICRO D.T.S.
29- FIXED GOBO WHEEL GOBO 1 DICRO DISTORTION GOBO 2 DICRO SCRATCHES GOBO 3 DICRO SPHERE GOBO 4 DICRO STONES GOBO 5 DICRO LEAVES D.T.S. Code: 0516G064 D.T.S. Code: 0516G065 D.T.S. Code: 0516G066 D.T.S. Code: 0516G067 D.T.S. Code: 0516G068 GOBO 6 GLASS ICE GOBO 7 DICRO SQUARES GOBO 8 DICRO DOTS GOBO 9 DICRO CIRCLES GOBO 10 DICRO TUNNEL D.T.S. Code: 0516G069 D.T.S. Code: 0516G070 D.T.S. Code: 0516G071 D.T.S. Code: 0516G072 D.T.S.
30- COLOUR WHEEL COLOUR 2 COLOUR 1 FULL CTO FILTER FULL CTB FILTER COLOUR 3 RED COLOUR 4 LIGHT RED COLOUR 5 ORANGE COLOUR 6 AMBER D.T.S. Code: (0507C062.D14) D.T.S. Code: (0507C063.D14) D.T.S. Code: (0507C064.D14) COLOUR 11 DARK BLUE COLOUR 12 BLUE D.T.S. Code: (0507C069.D14) D.T.S. Code: (0507C070.D14) D.T.S. Code: (0507C061.D14) D.T.S. Code: (0507C060.D14) D.T.S. Code: (0507C059.D14) COLOUR 7 YELLOW 1 COLOUR 8 YELLOW 2 COLOUR 9 DARK GREEN D.T.S. Code: (0507C065.D14) D.T.S.
NOTES
NOTES
NOTES
The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S. D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S.
