User manual
Table Of Contents
- 1 Table of contents1 T
- 2 Package Contents
- 3 Introduction
- 4 System overview
- 5 Control Surfaces
- 6 AXUM Engine
- 6.1 Console 1-4 configuration
- 6.1.1 IP/Clock configuration
- 6.1.2 Global configuration
- 6.1.3 Mix buss configuration
- 6.1.4 Monitor buss configuration
- 6.1.5 Source configuration
- 6.1.6 Extern source configuration
- 6.1.7 Destination configuration
- 6.1.8 Talkback configuration
- 6.1.9 Processing presets
- 6.1.10 Module assignment
- 6.1.11 Module configuration
- 6.1.11.1 Module configuration page
- 6.1.11.2 Module preset 1A/1B, 2A/2B, 3A/3B, 4A/4B
- 6.1.11.3 Processing
- These are the programmed processing defaults for the modules. Depending on the startup settings these processing defaults will be used at startup (programmed defaults in global configuration).The field ‘Use at source select’ determines if the default module processing in the source configuration is used when a source is assigned via the module source select functionality and no processing preset is assigned in the ‘source configuration’.
- The following state/value processing sections are available:
- 6.1.11.4 Routing
- 6.1.11.5 Set module 1 to programmed startup state
- 6.1.12 Mix/monitor buss presets
- 6.1.13 Console presets
- 6.1.14 Surface configuration
- 6.1.15 Rack configuration
- 6.1.16 Source pools
- 6.1.17 Preset pools
- 6.1.18 Users
- 6.2 System configuration
- 6.1 Console 1-4 configuration
- 7 Surface(s) website
- 8 Block diagrams – Must be created
- 9 I/O Rack description
- 10 Available I/O rack cards
- 11 Patch panels
- 12 Specifications AXUM digital audio system
- 13 List Of Figures
- 14 List Of Tables
- 15 Declaration Of Conformity
- 16 Product Safety
- 17 Disclaimer
- 18 Appendix A - Network design for AXUM
- 19 Appendix B – Surface service
- 20 Appendix C – Engine functions
A·X·U·M User Manual Version 2.5 - 2011-01-28
AXUM from D&R - Phone: +31 294 418014 - E-Mail: info@d-r.nl - 96 -
18.4 Network design (MambaNet over Layer 3)
When using MambaNet over UDP or TCP it is possible to use multiple racks in a single network.
It is important you realize that a single surface may connect to a single rack only.
MambaNet over UDP or TCP also gives possibilities to connect to AXUM Racks over the internet; this
requires port forwarding in the router between internet and your local network.
Layer 2 network (Ethernet),
also office network.
MambaNet
cloud 1
IP :192.168.0.101
Mask : 255.255.255.0
GW : 192.168.0.1
AXUM Rack
IP :192.168.0.100
Mask : 255.255.255.0
GW : 192.168.0.1
IP :192.168.0.10
Mask : 255.255.255.0
GW : 192.168.0.1
AXUM Surface
UDP to 192.168.0.100:34848
MambaNet
cloud 2
IP :192.168.0.201
Mask : 255.255.255.0
GW : 192.168.0.1
AXUM Rack
AXUM Surface
IP :192.168.0.200
Mask : 255.255.255.0
GW : 192.168.0.1
UDP to 192.168.0.100:34848