User manual
Table Of Contents
- 1 Table of contents1 T
- 2 Package Contents
- 3 Introduction
- 4 System overview
- 5 Control Surfaces
- 6 AXUM Engine
- 6.1 Console 1-4 configuration
- 6.1.1 IP/Clock configuration
- 6.1.2 Global configuration
- 6.1.3 Mix buss configuration
- 6.1.4 Monitor buss configuration
- 6.1.5 Source configuration
- 6.1.6 Extern source configuration
- 6.1.7 Destination configuration
- 6.1.8 Talkback configuration
- 6.1.9 Processing presets
- 6.1.10 Module assignment
- 6.1.11 Module configuration
- 6.1.11.1 Module configuration page
- 6.1.11.2 Module preset 1A/1B, 2A/2B, 3A/3B, 4A/4B
- 6.1.11.3 Processing
- These are the programmed processing defaults for the modules. Depending on the startup settings these processing defaults will be used at startup (programmed defaults in global configuration).The field ‘Use at source select’ determines if the default module processing in the source configuration is used when a source is assigned via the module source select functionality and no processing preset is assigned in the ‘source configuration’.
- The following state/value processing sections are available:
- 6.1.11.4 Routing
- 6.1.11.5 Set module 1 to programmed startup state
- 6.1.12 Mix/monitor buss presets
- 6.1.13 Console presets
- 6.1.14 Surface configuration
- 6.1.15 Rack configuration
- 6.1.16 Source pools
- 6.1.17 Preset pools
- 6.1.18 Users
- 6.2 System configuration
- 6.1 Console 1-4 configuration
- 7 Surface(s) website
- 8 Block diagrams – Must be created
- 9 I/O Rack description
- 10 Available I/O rack cards
- 11 Patch panels
- 12 Specifications AXUM digital audio system
- 13 List Of Figures
- 14 List Of Tables
- 15 Declaration Of Conformity
- 16 Product Safety
- 17 Disclaimer
- 18 Appendix A - Network design for AXUM
- 19 Appendix B – Surface service
- 20 Appendix C – Engine functions

A·X·U·M User Manual Version 2.5 - 2011-01-28
AXUM from D&R - Phone: +31 294 418014 - E-Mail: info@d-r.nl - 89 -
17 Disclaimer
Due to a policy of continuous product improvement, D&R Electronica Weesp B.V. reserves the right to
change specifications, appearance and performance without prior notice.
Since the use of this information and the conditions by which the products are used are beyond the
control of D&R Electronica Weesp B.V., it is the obligation of the owner and/or the equipment operator
to determine the correct and safe selection, settings and conditions of use of the equipment and
products.
To the extent that the law permits, any liability which may be incurred as a result of the use or future
use of a product manufactured or sold by D&R Electronica Weesp B.V. is limited to the cost of
repairing or replacing the failing product or component at the discretion of D&R Electronica Weesp
B.V. Either within or outside of warranty periods.
This does not extend to any loss or damage caused because of misuse or failure of the equipment or
products.
D&R Electronica Weesp B.V. shall not in any event be liable for economic lost of profits including
without limitation any incidental or consequential damage, expenses or other damages arising out of
the use or inability to use the product and/or software even if D&R Electronica Weesp B.V. has been
advised of the possibility of such a damage or for any claim by another party.
You agree to indemnify, hold harmless, and defend D&R Electronica Weesp B.V., its parent, and their
licensors, suppliers, officers, directors, employees, agents, affiliates, subsidiaries (collectively
"Indemnified Parties") from and against any and all liability incurred by or made against the
Indemnified Parties in connection with any claim arising from or related to your use.










