User manual
Table Of Contents
- 1 Table of contents1 T
- 2 Package Contents
- 3 Introduction
- 4 System overview
- 5 Control Surfaces
- 6 AXUM Engine
- 6.1 Console 1-4 configuration
- 6.1.1 IP/Clock configuration
- 6.1.2 Global configuration
- 6.1.3 Mix buss configuration
- 6.1.4 Monitor buss configuration
- 6.1.5 Source configuration
- 6.1.6 Extern source configuration
- 6.1.7 Destination configuration
- 6.1.8 Talkback configuration
- 6.1.9 Processing presets
- 6.1.10 Module assignment
- 6.1.11 Module configuration
- 6.1.11.1 Module configuration page
- 6.1.11.2 Module preset 1A/1B, 2A/2B, 3A/3B, 4A/4B
- 6.1.11.3 Processing
- These are the programmed processing defaults for the modules. Depending on the startup settings these processing defaults will be used at startup (programmed defaults in global configuration).The field ‘Use at source select’ determines if the default module processing in the source configuration is used when a source is assigned via the module source select functionality and no processing preset is assigned in the ‘source configuration’.
- The following state/value processing sections are available:
- 6.1.11.4 Routing
- 6.1.11.5 Set module 1 to programmed startup state
- 6.1.12 Mix/monitor buss presets
- 6.1.13 Console presets
- 6.1.14 Surface configuration
- 6.1.15 Rack configuration
- 6.1.16 Source pools
- 6.1.17 Preset pools
- 6.1.18 Users
- 6.2 System configuration
- 6.1 Console 1-4 configuration
- 7 Surface(s) website
- 8 Block diagrams – Must be created
- 9 I/O Rack description
- 10 Available I/O rack cards
- 11 Patch panels
- 12 Specifications AXUM digital audio system
- 13 List Of Figures
- 14 List Of Tables
- 15 Declaration Of Conformity
- 16 Product Safety
- 17 Disclaimer
- 18 Appendix A - Network design for AXUM
- 19 Appendix B – Surface service
- 20 Appendix C – Engine functions
A·X·U·M User Manual Version 2.5 - 2011-01-28
AXUM from D&R - Phone: +31 294 418014 - E-Mail: info@d-r.nl - 83 -
Line inputs : Electronically balanced
: Input impedance 10k Ohm
: input sensitivity +6dBu, maximum input +26dBu (+/- 20dB gain range).
: CMRR Line inputs: 30dB @ 1 kHz, maximum gain
: Transformer balancing is optional on the patch panels
Line Outputs : Electronically balanced
: Output impedance 56R Ohm.
: Nominal output level +6dBu, maximum output +26dBu
: Optional is transformer balancing
Digital Inputs : AES/EBU (AES3) or S/P-DIF
: 16/20/24 bit, 32kHz to 96kHz (optional built in sample rate converter)
: Input Impedance: 110R Ohm/75R Ohm
Digital outputs: AES/EBU (AES3) or S/P-DIF.
: 16/20/24 bit, 32kHz to 48kHz
: Output level: 2 to 5 volt
: Output Impedance: 110R Ohm/75R Ohm
GPIOs : All GPO’s are by opto isolated relays able to handle a maximum of 50V at 200mA
: All GPI’s have a 5V TTL 100kOhm circuitry
: GPIO-MIC has a 5V/600Ohm LED driver circuit
12.2 DSP processing
6 Bands EQ : +/- 18 dB, 20 – 20000 Hz, 0.1Q – 10Q LPF, LShelf, Peaking, HSelf, HPF, BPF,
Notch
Dynamics : Mentioned for voice processing use, you can setup the downward expander
threshold
: AGC threshold and ratio of working of the AGC.
12.3 OVERALL
Level : 0dBu = 0.775Vrms
: 0dB internal = -20 dBFs.
Clock : Sample rate: 32 kHz, 44.1 kHz, 48 kHz, +/- 20ppm (internally
synchronized)
Frequency response : 20 - 20.000 Hz +/- 0.2dB
THD+N : <-96dBfs
Dynamic Range : typically 105dB
Crosstalk : less than -90dBr
Noise : -86dBr