User manual
Table Of Contents
- 1 Table of contents1 T
- 2 Package Contents
- 3 Introduction
- 4 System overview
- 5 Control Surfaces
- 6 AXUM Engine
- 6.1 Console 1-4 configuration
- 6.1.1 IP/Clock configuration
- 6.1.2 Global configuration
- 6.1.3 Mix buss configuration
- 6.1.4 Monitor buss configuration
- 6.1.5 Source configuration
- 6.1.6 Extern source configuration
- 6.1.7 Destination configuration
- 6.1.8 Talkback configuration
- 6.1.9 Processing presets
- 6.1.10 Module assignment
- 6.1.11 Module configuration
- 6.1.11.1 Module configuration page
- 6.1.11.2 Module preset 1A/1B, 2A/2B, 3A/3B, 4A/4B
- 6.1.11.3 Processing
- These are the programmed processing defaults for the modules. Depending on the startup settings these processing defaults will be used at startup (programmed defaults in global configuration).The field ‘Use at source select’ determines if the default module processing in the source configuration is used when a source is assigned via the module source select functionality and no processing preset is assigned in the ‘source configuration’.
- The following state/value processing sections are available:
- 6.1.11.4 Routing
- 6.1.11.5 Set module 1 to programmed startup state
- 6.1.12 Mix/monitor buss presets
- 6.1.13 Console presets
- 6.1.14 Surface configuration
- 6.1.15 Rack configuration
- 6.1.16 Source pools
- 6.1.17 Preset pools
- 6.1.18 Users
- 6.2 System configuration
- 6.1 Console 1-4 configuration
- 7 Surface(s) website
- 8 Block diagrams – Must be created
- 9 I/O Rack description
- 10 Available I/O rack cards
- 11 Patch panels
- 12 Specifications AXUM digital audio system
- 13 List Of Figures
- 14 List Of Tables
- 15 Declaration Of Conformity
- 16 Product Safety
- 17 Disclaimer
- 18 Appendix A - Network design for AXUM
- 19 Appendix B – Surface service
- 20 Appendix C – Engine functions
A·X·U·M User Manual Version 2.5 - 2011-01-28
AXUM from D&R - Phone: +31 294 418014 - E-Mail: info@d-r.nl - 34 -
6.1.11.2 Module preset 1A/1B, 2A/2B, 3A/3B, 4A/4B
Here you select the source, processing preset and routing preset that is used when module preset
1A/1B, 2A/2B, 3A/3B, 4A/4B is selected. After a click on ‘routing’ a popup appears with the routing
possibilities (this depends on the console assignment).
• Source
If you click here a popup appears with a list of all available sources. Select the source you
want to use in this module preset.
• Processing
If you click here a popup appears with a list of all available processing presets. Select the
source you want to use in this module preset.
• Routing Preset
Figure 20: Module routing preset
Override module
If set to no, the module setting will not be affected by this preset. If set to yes, this preset will
change the settings of the module for the corresponding buss.
Level
If the override is turned to yes, this will set the send level to the buss for this module when
current preset is selected.
State
If the override is turned to yes, this will set the buss state to ‘on’ or ‘off’ for this module when
this module preset is select.
Pre/Post
If the override is turned to yes, this will set the buss pre or post for this module when this
module preset is select.
Balance
If the override is turned to yes, this will set the buss balance for this module when this module
preset is select.
To all console 1-4 module
With this link you can copy the current settings to the same routing preset (1A/1B, 2A/2B,
3A/3B, 4A/4B) at all modules of the console where this module is assigned to.