STANDALONE H.
Before usage The User manual is for DVR installation and operation. The User who install the device first or Qualified Personal, before installing DVR, has to read user manual carefully and follow warning instructions avoiding malfunction of operation or product failure. Refer all servicing to qualified service personnel or suppliers while install and set the DVR. Keep these operation instructions handy for future reference.
Approved HDD List Capacity Manufacturer HDD Western Digital 250G Hitachi MODEL Name F/W Ver.
- CONTENTS 1. OVERVIEW ∙ Features ………………………………………………………………………………………………………..……………………….…...……..6 2. INSTALLATION ∙ Package Contents .………………………...………………………….…………………………………………………………….…..…….7 ∙ Part Names and Functions (Front) …………………….………………………………………………………………....….……...8 ∙ Part Names and Functions (Rear) …………………..…………………………………………………………………….….………9 3. SYSTEM OPERATION ∙ Menu Setup ……………….…………………….……………………………………………………………………..………………...…….10 ∙ Icons ……………………….……………………………………………………………………………………………………..……………..
∙ Camera …………………...…………………….………………………………………………………………………..……..………….…..…26 ∙ PTZ Setting ……………………………..…………………………….….…………………………………………………………….....……26 ∙ Using Pan/Tilt ………………………….……………………….…………………………………………………………………..…....……28 8. RECORD SETUP ∙ Recording Setting …………………..….…………………………..……….……………………………………………………...……….30 ∙ Schedule Record …………………..…….…………………………..……….……………………………………………………..……….31 ∙ Holiday Record ………………….……..........…………………………..……….………………………………………………...……….32 9. EVENT SETUP ∙ Sensor ……………………………………...
Features The DVR employs H.264 video encording 4 channel input, audio encoding for 4 channels while simultaneously supports hard disk recording and playback. The DVR has mirroring function, mirroring HAD record and display regardless of unexpected physical shock or demage.
Package Contents Please unpack the product, and place the product on a flat place or in the place to be installed. Please check the following contents are included in addition to the main unit.
(Front Panel) [1] Sequence of 4-Split and Auto Sequence in order by pressing more than 3 seconds [2] USB Connection Port [3] Channel Keys [4] Remote Control Receiver LED [5] LED Indicator (Power/REC/HDD Status/Network) [6] Buttons for Direction / Select / Play / Pause [7] MENU [8] PTZ Control [9] Search [10] Audio [11] Emergency Recording [12] Backup Part Names and Functions (Rear) 8
[1] Audio Out : Output Port for the Audio Signal [2] Audio In (1~4) : Input Port for the Audio Signal [3] Video In : Input Port for composite Video Signal [4 Video Out : BNC Type of Output Port for the composite Video Signal [5] VGA : Output Port for VGA Video Signal [6] NETWORK : Network Connection Port [7] Alarm / Sensor / RS-485 (When you connect to PTZ Cameras) ( Refer to the detailed settings in each part in the manual.) [8] Power : Port to be connected to DC 12V/3.
3. SYSTEM OPERATION Menu Setup The MENU can be operated by pressing the Front Menu Button or using the Remote Control. ☞ Using Front Buttons 1) Press the “MENU” Button. 2) Use the Direction Keys and to selece the MENU and “MENU” Button for “ESC” ☞ Using Remote Control - Press “SETUP” Button . ☞ Using Mouse 1) Right-click any area of the screen and the MENU will pop up. 2) Left-click to enter the MENU. Icons [1] The Icons indicate the Status in Live Mode.
[3] Recording Status Icon REC Video Loss Motion Detected Sensor Detected 11
[4] Status Bar • Date / Time • “ER” : Emergency Recording / “SR” : Schedule Recording • Network Connection / Screen Lock • Shows the available capacity of the Hard Disk and “OVERWRITE” when you write again above the current datas. z Using Remote Control You can control all the functions with this Remote Control. It’s easy to carry and available to operate Multi DVRs’ with 1 Remote Control. [1] ID : If you want to control Multi DVRs’ in 1 Remote Control, put this “ID” to select each number.
[3] BACKUP : To use USB MEMORY STICK for BACKUP [4] AUDIO : Turns AUDIO ON/OFF and you can select each channel. [5] SEQ (Sequence) : Displays “Auto Sequence” and the Channels automatically you set.
[1] Changing the Remote ID 1) Check the Remote ID in ‘SYSTEM” Menu. 2) Menu Æ System Æ Information Æ Remote ID (0 ~ 99) * The Default Setting is “0”. If you control Multi DVRs in only 1 Remote Control, put different ID Numbers. * Use the Remote Control only when you change the ID. If you use the Front Keys, the ID is not changed correctly. 3) Press the “ID” Button on the Remote Control and then you can see the menu to change the DVR ID. (Refer to the above picture.
4. System Configuration System Setup [1] Remote ID : Assign the ID of Remote Control so that user can separately control Mun\lti DVRs with 1 Controller. (ID Range : 0 ~ 99) [2] Mouse Sensitivity : Changes the Sensitivity Level for the Mouse for user’s convenience. ( Basic : 1, to increase the reaction speed : 1 < 2 < 3 ) [3] Language: Selects your Language.
Time/Date [1] Time : Set the Time [2] Date : Set the Date [3] Date Format : Year(YYYY), MOnth(MM), Day(DD) [4] Day Light Saving Time (Summer Time) : If you select “Yes”, the time makes 1 hour earlier than the GMT of its time zone. [5] Time Server : Synchronizes the Time automatically with Time Server Service. √ Time Server : Input the URL of the server (Default : kr.pool.ntp.
Password [1] ID : You can use till 8 IDs at most. (Admin ID & User ID:1~7) [Note] Default ID : “11111111” [2] Function : You can set the permissions of each user to access te below menus. ㅇ Configuration ㅇ Hard Disk ㅇ Search ㅇ Back up : ㅇ PTZ Setting ㅇ REC Key at the Front Pannel ㅇ Camera Hard Disk This HDD Management is closely connected to the “Record” Menu. It may cause the malfunctions if the setup is wrong so make sure that it is set correctly.
[1] Hard Disk List : shows the HDD information including External Disks and supports Format. ㅇ Hard Disk1 : the Capacity of Hard Disk Drive ㅇ USB1 : the Capacity of external USB1 connected ㅇ USB2 : the Capacity of external USB2 connected ㅇ Erase Data : Selects and format the Disk you choose [2] Total : Displays the capacity of HDD ( Total Size / Used Size) [3] Erase Data : Formats the datas for selected disks ㅇ Main Disk : Deletes the datas in Main Disk. ㅇ Mirror Disk : Deletes the datas in Mirror Disk.
Default Setup [1] Default Setup : Initializes the system excluding major configurations like Network, Password, Recording Setup. [2] Factory Setup : Initializes all the system to the factory default.
the Front Port 1 or 2. Firmware USB Memory Stick [NOTES] Do not turn off the power or remove the USB stick during this backup. It may cause the malfunctions and please contact us if it is stopped without any message. [2] Configuration BACKUP : Back-up DVR configuration in USB memory stick. [3] Configuration LOAD : Down load desired DVR configuration in other DVR.
RS-485 This DVR supports RS-485 Communication to control the PTZ Cameras or Control Keyboards. You can use RS-485 Communication to control P/T/Z when you connect PTZ Cameras or Keyboards. It may be differnt for each brand so refer to those manuals not to be confused. √ Baudrate / Parity / Stopbit : Select the functions with the manual of the products’ manual you want to connect.
5. DISPLAY SETUP OSD You can select the options which are displayed in the screen. [1] Camera Title : Gives the name of each camera. [2] Status Bar : displays the Status for some information at the below. [3] Multi screen Border : Divides the Screen Borders [4] Login Menu : shows the “Login Menu” after rebooting the DVR. • Booting UnLock : login automatically. • Booting Lock : displays the “Login Menu” to start the DVR. [6] Alphablending : Selects the level of transparency for the backgrond of the Menu.
▷ Auto Loss Skip : If there’s no video input, this menu is not applied. ▷ Display Time : Selects the Display Duraion for each channel. ( 1sec ~ 30sec) TV Adjustment [1] Monitor : Select the ratio of the Monitor. ( Currently, the Monitor with 4:3 is available only.) [2] Icon : The OSD Posion is changed accoring to the size of a Monitor you use. • Small : for a small monitor • Normal : for a normall sized monitor • VGA : for a LCD Monitor [NOTES] The mode “Small” and “Normal” is available in CRT Monitor.
6. NETWORK SETUP IP Address Setup It provides networked monitoring of Live Screen from a remote place and you have to setup some infromation to use correctly. Please check whether your Network Connection Mode is Dynamic IP(DHCP) or Static IP before setting. [1] DHCP : “ON” for Dynamic IP Users / “OFF” for Static IP Users [2] IP Address : The users for “Dynamic IP” don’t need to set it but for “Static IP Users” have to input the Addresses same as below examples.
Web Server This DVR includes Built-in Web Server so you don’t have to install additional program for Networked Monitoring.. If you put IP Address only in Local Network, you can control the DVR remotely. [1] On/Off : “On” – Use the Networked Monitoring in Local Network “Off” – Use the Networked Monitoring through Web. [2] Use Port : Connection Port for Remote Control [Example] IP Address : 61.250.157.50 / Port : 2001 Æ http://61.250.157.
7. CAMERA SETUP Camera Set the name of each camera. You can input the names with the Keyboard on the screen after choosing the Channel. PTZ Setting Is’s the setting when you use PTZ Cameras.
[1] Channel : Selects the channel you want to connect. [2] ON/OFF : ON : Use PTZ / OFF : Do not use PTZ.(Default : On) [3] MODEL : Selects the Model Name or its Protocol. (Defalut : D-Max Protocol) [4] ID : Selects its ID (Range : 0~255 / refer to the manul for each brand you use.) Advanced Advanced Menu is available only for the models which have detailed PTZ Setup menus. [1] Reverse Control(Pan) : Set the direction of its working reversely.
The touring number is selectable from 1 to 16 and works in order. [1] Touring Number : Selects the order [2] Preset Number : Selects the Preset Number saved before. [3] Touring Interval (/SEC) : Selects the Touring Dwell Time. [NOTES] Selecting the Protocol for PAN/TILT When you select the Protocol, its name is registered in the Name of Camera or Protocol. Using Pan/Tilt You can select this menu same as below. • Using Mouse : Right-click any are of the sreen and select the PTZ.
ㅇ Preset : Input the Preset Number to move or save and then Save ( (Moves to select Preset) ) it. (Saves the Preset) ㅇ Tour : Moves the Saved Presets automatically in order. ㅇ MENU : shows the “Pan/Tilt Menu” ㅇ Channel : available to change the Pan/Tilt Channels in Multi-channels. Select the “Channel” Menu and then move to other channels with direction keys. ㅇ Exit : Ends the PTZ Mode.
8. RECORD SETUP Record Setting The Recording Setup is to select the detailed values like Recording Resolution,Frames and so on. The Recording File Size can be bigger according to this setting so be careful to set it. [1] Channel : Selects the Channel. [2] ON/OFF : Checks the selected channel to be recorded or not. [3] Resolution : Sets the Recording Resolution. [4] Quality : Sets the resolution of recorded screen. ( HIGHEST > HIGH > NORMAL > LOW > LOWEST) [5] Speed : Selects the Recording Frames.
Schedule Re Schedule Record Makes your reservation on a date, time, and channel to schedule the recording per 30 minutes. █ N (Grey) : No record █ C (Green) : Continuous Record █ M (Blue) : Motion Detected Record █ S (Red) : Sensor Detected Record █ M+S (Yellow) : Motion and Sensor Detected Record 1. Select the Channel. 2. Once you select the Date and Time, choose the one of above options. It moves from “N” to “M+S” in order. (N Æ C Æ M Æ S Æ M+S) 3.
Holiday Record Different Record Setting can be applied to each holidays. [1] You can select the Holiday Record with 7 differnt types. After selecting the type (H1 ~ H7), drag with mouse or use the direction keys with Remote Control. [2] Slescts “Holiday” in the Menu and the Holiday Type (H1 ~ H7) in the Calendar.
Whenever you click the date, the color is changed, which means the different types of its setting “H1 ~ H7”.
9. EVENT SETUP Sensor You can set the Sensor’s Input condition and related camera. [1] Sensor Input : Selects a channel to be connected to the sensor. [2] On/Off : Selects the use of this Sensor. [3] Input Type : Selects the Sensor Input Type • N/Open (NORMAL OPEN) : Sensor is opened. If the sensor is closed, it generated alarm. • N/Close (NORMAL CLOSE) : Sensor is closed. If the sensor is open by interruption, it generates alarm.
[1] Channel : Selects the Channel to use Motion Detection. [2] On/Off : Selects the Motion Detection Use. [3] Sensitivity : Selects the Sensitivity of Motion Detection. Use the Value after testing this Sensitivity in advance before saving it. [4] Detection Area : Sets the Motion Detection Area. Use the direction keys to set the areas and press “Enter” button. • MD selected area : Pink Color • MD non-selected area : No color • If the motion is detected, the area is with green.
[APPLY TO ALL] Use the following keys to “APPLY TO ALL”. “1” Button : Select ALL “2” Button : Release ALL [Using Mouse] Right-click from the Starting Position and drag it to the finishing position for Motion Detection Area. Camera Tamper Detection When the image is detected with too dark or bright, it recognizes as an event. Normally, it detects the situation when the door/window is open or the camera is blocked with some materials.
[1] Motion : Sets PTZ, Popup, Relay Out, and Buzzer when the Motion is detected. • Channel : Selects a channel to apply. • Preset Channel :Selects a Preset Camera to apply when Event happens. • Preset Number : Selects a Preset Number to move. • Popup Channel : Selects the use of Popup . • Popup Duration : Sets the Duration to keep the Popup window. • Relay Out : Selects the Alarm Out. • Relay Duration : Sets the duration of alarm signal.
• Channel : Selects a channel to apply. • Preset Channel : Selects a Preset Camera to apply when Event happens. • Preset Number : Selects a Preset Number to move. • Popup Channel : Selects the use of Popup . • Popup Duration : Sets the Duration to keep the Popup window. • Relay Out : Selects the Alarm Out. • Relay Duration : Sets the duration of alarm signal.
• Channel : Selects a channel to apply. • Preset Channel : Selects a Preset Camera to apply when Event happens. • Preset Number : Selects a Preset Number to move. • Popup Channel : Selects the use of Popup . • Popup Duration : Sets the Duration to keep the Popup window. • Relay Out : Selects the Alarm Out. • Relay Duration : Sets the duration of alarm signal.
• Channel : Selects a channel to apply. • Preset Channel : Selects a Preset Camera to apply when Event happens. • Preset Number : Selects a Preset Number to move. • Popup Channel : Selects the use of Popup . • Popup Duration : Sets the Duration to keep the Popup window. • Relay Out : Selects the Alarm Out. • Relay Duration : Sets the duration of alarm signal.
10. SEARCH SETUP Search You can perform the Search for recorded data by the time, Motion Detection, Sensor Detection, and so on. [1] Accessing the Search Menu : Press the “Search” Key on the Front Key, Remote Control, and the right button of the Mouse.
[2] You can see the graph, which shows the Channels, Time for recorded data. After selecting the time, press “Enter” button. [3] The recorded data is shown as a graph and select the minutes to Search. This Search is based on Year/Month/Date/Time you selected and it switches the “Play Mode”.
Date/Time Search If you know the specific Date/Time, you can search the recorded data directly with the inputs. [1] Record Begin : Shows the beginning time in the recorded data. [2] Record End : Shows the end time in the recorded data. [3] Channel : Selects the channel to search (specific chnnel or All) [4] Play Begin : inputs the Time to search. [5] Play : Clicks “Play”.
Event Search It searches the Event in the selected date. [1] Selects the disk to search. [2] Day : Selects the day to search,. [3] Channel : Selects the channel to search. [4] Event Type : Selects the type of Event to search. (MD/Sensor/Video Loss/System/All) [5] Search : Clicks ‘Search” if you finish selecting the above options to search. [6] It shows the list of the Event you selected and then choose one of them to play.
Go to first / Go to last It searches the first or last data from the recorded data in the HDD. Play Control Description of Search Buttons Using Mouse Using the Front Keys [1] Play [6] Fast Rewind [2] Pause [7] Audio On during Play [3] Stop [8] Calendar Search during Play [4] Step Rewind [9] Mark In/Out : [5] Fast Forward Mark In : During the playback, the backup starts by clicking this button. Mark Out : During the playback, the backup ends by clicking this button again.
Audio You can use the Audio during the Live View or Playback. [1] Opening the Menu : Click the “AUDIO” button on the Remote Control or right-click any area on the Mouse in Live or Playback.
11. BACKUP SETUP Backup You can backup the desired data to a connected device. After connecting the USB into the DVR, press the “BACKUP” button on Remote control or rightclick of the Mouse to find the “POP-UP MENU Æ BACKUP”. [1] Select the connected device. If it’s recognized normally, it shows the capacity of the device with the message “XXX MB”. [2] Select the date to backup the data.
[3] Double-click the time. [4] Select the minutes. If you click “--------“ below, the time is input automatically.
[5] Input the end-time. • If the end-time is same hour from the starting time, click the minutes and then move to “-------“ below. The time will be shown automatically. • If the end-time is different hour from the starting time, press the “MENU” button to moves to the previous step. After input the differnt hour and minute, click “-------“ below for automatic input. [6] Camera : Selects the channel for backup the data. (selected channel is with red.
It shows “Backup Size / USB Capacity” and press “OK” to start backup. [8] If the backup is completely done, you can see the below file in the USB memory stick. Click the file to play the data. [9] Using the Viewer Program. (It plays automatically if you click the backup file.) ① Scroll Bar : Indicates the current playing location from the total playback. ② Open : opens other backup files. ③ Fast Rewind ④ Plays backward ⑤ Step Rewind : Used for backward frame-by-frame search while in PAUSE.
⑩ 4-Split Mode ⑪ 9-Split Mode ⑫ 16-Split Mode ⑬ Captures current image ⑭ Converts into AVI File. If you want to convert the file into AVI File during the Playback in any channel, please click the scroll bar for the Start Time and End Time. After checking the time in the below bar, press the ‘AVI” Button. You can backup this data directly to other device. ⑮ Audio Output buttons : Clicks the Channel Buttons you want to use Audio.
11. APPENDIX SPECIFICATION ITEM Video 4CH Video format NTSC/PAL Video inputs 4CH Compression H.264 Video outputs Composite (1) , VGA (1) Playback Record Split / Full screen Speed NTSC : 120fps, PAL : 100fps Frame D1 (30 fps) / Half D1 (60 fps) / CIF (120 fps) Event Continuous, Schedule, Motion, Sensor Audio In/Out 4/1 Alarm In/Out 4/1 Network Communication Other LAN [10/100, Ethernet (RJ45)] CODEC H.
Product Warranty This unit has thoroughly been tested and passed on quality control& quality assurance. Based on the warranty, If this unit malfunctions during normal use, you will be guaranteed to get your item repaired free of charge under joint agreement based on thee warranty. [Tips on warranty]. ■ Check out the Warranty first. ■ Check the item again what is wrong with it and contact the seller of this unit.
■ For safe use of system and to prevent product failure or accident, please read this manual carefully before use. ■ The manual includes “Product Warranty”. Be sure to keep it handy for later reference.
