Super Wide Dynamic Range Dome Color Camera 사용 설명서 MANUAL 용 서 Pixim Seawolf DSP
The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
■ Warning The camera needs periodic inspection. Contact an authorized technician for inspection. Stop using your camera when you find a malfunction. If you use your camera around smoke or unusual heat for a long time, fire may be caused. Do not install the camera on a surface that can not support it. Unless the surface is suitable, it could cause falling or other hazards. Do not hold plug with wet hands. It could cause an electric shock. Do not disassemble the camera.
1. Features Our WDR camera is a superb wide dynamic range camera which achieves 120dB max(102dB typical) of dynamic range of the image by implementing PIXIM's Seawolf digital imaging system.
2. Cable Connection and OSD Control 1) Cable Connection 2) OSD Control ② SETUP button : Used for the menu display. This button can be used to confirm settings after changing the value of the selected function or current conditions. ③ UP & DOWN buttons : Used for selecting items by moving the cursor up or down on the menu screen.
3. Setup Menu Operation 1) In the menu Use ▲, ▼ buttons to move menu, ◀, ▶ buttons to change the settings and press button shortly to select or enter. button stands for MENU or ENTER button. 2) Entering menu Press button longer than 2 sec on the back of camera. 3) MAIN Follow below chart for submenu setting. MENU Default Descriptions Sets COLOR ROLL COMP., AE PREFERENCE, WDR CONTROL and EXPOSURE SENSE-UP. Sets OFF, AUTO or NIGHT OFF – Day/Night is disabled and camera works as a normal color camera.
4) EXPOSURE To enter EXPOSURE menu, press EXPOSURE EXPOSURE button at MAIN>EXPOSURE. Descriptions Descriptions In NTSC system, the entire color tone on the monitor may continuously Medium level of the reddish dynamicand range control for each PRESETs. move greenish. WDR HIGH COLOR Increases the COLOR dynamic ROLL range COMP. control. -Some highlight arearolling may washed out.fluorescent Reduces the color under the CUSTOM...
5) DAY/NIGHT To enter EXPOSURE menu, press button at MAIN>DAY/NIGHT>AUTO... IMPORTANT!!! IMPORTANT!!! DAY->NIGHT and NIGHT->DAY operations must be examined and verified at the final step of the installation. Block the lens for a few seconds for NIGHT mode and release and let it return to DAY mode. If camera stays at NIGHT mode more than 10sec, increase N-->D THRES a little and repeat the fore-mentioned steps.
6) 3D NR To enter EXPOSURE menu, press 3D NR button at MAIN>3D NR Default Descriptions Determines the depth of Three Dimensional Noise Reduction. DEPTH 47 High value reduces the noise strongly but the comet effect may occur for the fast moving object and vice versa. 7) LENS SELECT To enter EXPOSURE menu, press DC/ MANUAL button at MAIN>LENS SELECT>DC... or MANUAL... Default Descriptions Lower value opens the lens iris and increases the brightness and vice AI LEVEL 24 versa.
PICTURE PICTURE Factory Factory CONTROL PICTURE CONTROL Default Factory Default CONTROL Default Descriptions Descriptions Descriptions Sets Sets ATW ATW Normal, Normal, ATW ATW Desat, Desat, ATW ATW Xtnd Xtnd or or MANUAL. MANUAL. ATW NORMAL –– Compensates automatically in Sets Normal, ATW Desat, ATW Xtnd or MANUAL. ATWATW NORMAL Compensates automatically in range range of of 2800K-7500K. 2800K-7500K. WHITE WHITE ATW DESAT automatically in range of 2000K-11000K.
① MOTION Up to 4 motion areas and the sensitivity can be set. The sensitivity is applied for all zones equally. In adjusting each zone, the zone border line changes color when pressing button. Green enables enlarging, red enables reducing and white enables moving the zone by ▼, ▲, ▲, ▼buttons. To exit MOTION ZONE SETUP, press button for 2 seconds. ② PRIVACY AREA Up to 6privacy area can be programmed in size, position and mask color. Use joystick to change size, position and mask color.
Right after pressing button at ,ON..>, the Right after one more pressing button, the 1st zone appears on top-left corner in orange. 1st zone changes to blue. The orange colored zone can be relocated in its Blue colored zone can be resized with . ▼, ▲, location with ▼, ▲, ▲, ▼ buttons. ▲, ▼ buttons An example of mask when resizing by . ▼, ▲, An example of mask when relocating. ▲, ▼ buttons Press button longer than 2 sec. to return to previous menu.
D-EFFECT Default FREEZE OFF Descriptions Image freezes and shows the still image at the moment when set to ON.. OFF(Normal display), H-FLIP(left & right flipped), V-FLIP(upside down FLIP OFF flipped), H/V-FLIP(left & right flipped and upside down flipped.) Direction of joystick control should be flipped if V-flip is flipped to H/V-flip. D-PTZ Able to set digital zoom up to x12 and digital PAN/TILT if zoom ratio >1. D-PTZ Default Descriptions ZOOM 1 Digital zoom can set up to x12.
If there are problems in operation, please refer to the items below. If the problem persists, 4. Troubleshooting please contact the agent you purchased this product from. Problems Nothing appears on the screen. Troubleshooting • Please check the power connection. • Please check the video signal line connection. • Please check and make sure that the auto lens switch is set to DC (VIDEO) when using a VIDEO(DC) lens. The video image is not clear. • Please check if the lens is clean.
5.
6. Specifications ▪ GENERAL Model name NTSC PAL Image Device 1/3" CMY Color DPS SENSOR (Pixim Seawolf D8800C series) Effective Pixels 768(H) x 540(V) TV system NTSC, 525lines / 2:1interlace PAL, 625lines / 2:1interlace Scan frequency. 59.94Hz(V), 15.734Khz(H) 50Hz(V), 15.625Khz(H) Synchronization Internal/Line lock (Default: Internal) H. Resolution 690TV Lines Sensitivity 0.0008Lux Class sensitivity (0.
▪ DOME CASE Dome Type Install Type Dimension(mm) 3 Axis Material Weight Indoor Outdoor(IP66) Outdoor(IP66) 100(Bubble) x 139.5(H) 100(Bubble) x 103(H) 100(Bubble)x 107.5(H) 3 Axis 3 Axis 3 Axis Plastic Body, PC Bubble, PC Bubble, PC Bubble Aluminum Body Aluminum Body 560g 1.1Kg 1.
