CONTROL KEYBOARD USER MANUAL DCK-255 DCK-255 CCTV CONTROL KEYBOARD PRESET ALL RUN HOLD 1 2 3 4 5 6 SWING Z/I Z/0 F/F F/N MENU STAUS ALAR 7 8 9 C/P L/P AUX1 CLR 0 ENT CAM MON QUAD AUX2 ALARM ON OFF GROUP TOUR SET
Table of Content 1. Advisement 4 2. Confirming the Contents of the Package 6 3. Main Features and Functions 7 4. Appearance and Function Keys 5.
1. Advisement WARNING Always have the unit installed by the store it was purchased from. z Improper connections and/or installation could result in electrical shock, fire or other serious injury or damage. Do not place the unit on an unstable surface. z Always checks the strength and stability of the installation location. z A falling unit will result in damage and could cause serious injury. Never disassemble or attempt to repair or modify the unit.
CAUTION Always use the unit indoors. z The unit should never be used outdoors, or in any place where it will be exposed to rain or other extremes of moisture. z Direct exposure to water will result in rust and will damage the unit. Never use in environments that have heavy concentrations of dust, smoke, steam or humidity. z Environments such as these could result in fire, electrical shock or other serious damage or injury. Never place the unit in extremes of high or low temperatures.
2. Confirming the Contents of the Package 1) Control Keyboard Unit : 1 PC 2) Junction Box : 1 PC.
3. Main Features and Functions Synopsis This controller is used to operate pan / tilt / zoom dome cameras and speed dome cameras. This is able to control the maximum of 255 cameras and lot of sub-keyboards. It is also controlled CCTV Receivers, Matrix Systems, Alarm Receiver and other controlled Equipments. Dome Camera can set and fulfill the surveillance function as preset, swing, group(it means tour), tour(it means auto-tour) and etc with the keyboard controller.
4.
The keyboard is wired directly to a maximum of 255 receivers, dome cameras. You can communicate using D-MAX Protocol. It has an exclusive RS-485/RS-422 chip set into the keyboard to communicate. There is power supply terminal to use keyboard in rear junction box. The power supply is for 12 VDC included package.
Communication to the keyboards is RS-485. Maximum cable distance for RS-485 communication over 24-gauge wire is 1.2 Km (App. 4000 feet). We recommend using shielded twisted pairs cable that meets or exceeds the basic requirements for EIA RS-485 applications. Junction Box’s input and output terminal Plug the power supply, 12 VDC into suitable outlet on the rear of the junction box. It is also supplied power to keyboard. It is included into keyboard package.
5. Functions and Operations Main keyboard is setup for regular products. So sub keyboard needs to be set. (If you want to use sub keyboard, please ask to the supplier of it.) 1) Initial Setup of Keyboard Plug in the power supply and then the menu screen appears on LCD with a sound as below. Please Wait! Camera : 001 Input? [MAIN] Version X.
SET SUB KEYBOARD DC9V CONTR CONTR SUB OL. 1 OL. 2 KEY. 485+ 485- SET MAIN KEYBOARD DC9V CONTR CONTR SUB OL. 1 OL. 2 KEY. 485+ Up to 128 cameras 485+ 485+ 485- 485- 485- 485+ 485485+ 485- Up to 128 receivers 485+ 485- 485+ 485- This keyboard can be converted to Matrix main (or, sub) keyboard, CCTV Transmitter main (or, sub) keyboard. For matrix, please refer to the matrix manual.
3-1. Initial setting Select Sub-keyboard. Plug in one end of RJ-45 cable from data junction box to rear of keyboard terminal port at the same time press SET button during 3 Seconds. It appears message with a sound as below figure.
2) Select Camera ALL RUN HOLD 1 2 3 4 5 6 7 8 9 C/P L/P CLR 0 ENT CAM MON Z/I Z/O F/F F/N AUX1 AUX2 ALARM VIEW ON OFF MENU STAT. Enter camera number (1 ~ 255) and press CAM to select. Select camera : 1~ ¨ CAM 3) Joystick and operation of camera in manual The camera selected can be operated by joystick. It should be operated pan / tilt / zoom with the joystick. (a) Pan/Tilt/Zoom Operating Move the joystick until the camera reached the desired position.
4) Camera Setup (Enter into OSD Menu) OSD (On Screen Display) Control The Keyboard can be controlled speed dome camera, ptz dome camera with OSD menu. Enter into OSD Menu ALL RUN HOLD 1 2 3 4 5 P-SET SWING Z/I Z/O F/F F/N MENU STATUS 6 7 8 9 CLR 0 ENT GROUP TOUR SET KEYBOARD FIGURE 1 + MENU (1) Press number 1 and MENU button respectively to enter OSD menu on the screen. NOTE : The distance time between push 1 and MENU button is about 2 ~ 3 sec.
NOTE : The distance time between push 1 and MENU button is about 2 ~ 3 sec. 5) Presets The keyboard can be programmed up to 64 preset positions for each camera. The memorized preset position is available to replace new preset position and it can be changed.
Ex) delete the preset number 5. CLR (press more than 3 ¨ ¨ 5 P-SET ¨ ENT Press CLR button, number (5), P-SET, and ENT button respectively. Delete all preset Press CLR button for a while (more than 3 sec), and press PST button and press finally ENT button. ¨ CLR P-SET ¨ ENT 6) Swing The keyboard can be programmed 1 of swing for pan swing and tilt swing in each.
Run swing (a) Auto-pan : Enter number (1) and press SWING button. 1 ¨ SWIN (b) Auto-tilt : Enter number (2) and press SWING button. 2 ¨ SWIN Stop swing Press SWING button or touch the joystick. 7) Groups (Tour Surveillance Function) It is a sequence surveillance function with presets. With the function, it should be made a surveillance to preset position as desired automatically. In the setting mode, it can be programmed speed value, dwell time and number of sequence.
(d) Enter dwell time (1 ~ 127). ¨ 1~127 ENT (e) To save and exit group set mode press SET button. Run Group : Enter group number (1~6) as desired and press GROUP button. ¨ 1~127 ENT Stop Group : press GROUP button or touch the joystick. All Group Clear Press CLR button for a while (more than 3 sec.) and press GROUP and ENT button. ¨ CLR ¨ GROUP ENT 8) Tour (it means auto-tour surveillance function) The keyboard should be programmed 1 of tour sequence included up to 6 groups.
(d) To finish setting, press SET button. Run Tour : Press TOUR button. Stop Tour : Press TOUR button or touch the joystick. Clear all tour : Press CLR button for a while. (more than 3 sec) and press TOUR and ENT button. ¨ CLR ¨ TOUR ENT 9) Spiral Function This function will be supported only at speed dome camera, the fixed pan speed and tilt speed is operated at the same time that can make a spiral surveillance function. Enter number (7) and then press MENU, ON/OFF button.
Memorize PTZ Trace : button respectively. 9 ¨ MENU ¨ Enter number (9) and then press MENU button, ON ON Delete memorized PTZ Trace : Enter number (9) and then press MENU button, OFF button respectively. 9 ¨ MENU ¨ OFF When manipulating according this setting the message of “Trace memory” appears on the screen. At the moment, move pan, tilt and zoom with the joystick. If the memory time expires, the memorizing stop automatically and memorized ptz is registered.
6. Maintenance and Mending If the surface of the keyboard becomes dirty, turn off the power and wipe the surface with a soft dry cloth. CAUTION z Never use strong cleaners, such as alcohol, benzene or paint thinner to clean the surface of the keyboard. They will damage the surface and could cause fire or other accidents. z Cleaning and inspecting of the internal components should only be performed by authorized technicians. Contact your nearest representative for details.
It does not work alarm on. Did you make sure of turn off all of alarm channels? If alarm channel is off, it does not work alarm on. 7. Dimensions 83. 337. 31. PRESET ALL RUN HOLD 1 2 3 4 5 6 SWING Z/I Z/0 F/F F/N MENU STAUS GROUP TOUR SET ALAR M 7 8 9 C/P L/P AUX1 AUX2 ALARM CLR 0 ENT CAM MON QUAD ON OFF 179. D-max 10 KEYBOA 29 108, 92.
1) Controller Item Input/output terminal Interface between junction box Working temperature Storage temperature Working humidity Storage humidity Dimension Weight Specification Modular Jack TTL 0 ~ 40 °C -5 ~ 55°C Less than 75%RH Less than 95%RH 338(L) x 180(W) x 84(H) 1.
4) Camera control interface ITEM Specification Asynchronous Serial Interface 1 Start bit Synchronization system 8 Data bit & DATA length No parity 1 Stop bit 11 Byte command Signal polarity Mark logic "1" Space logic "0" Transmit system Half duplex Communication speed 9600 bps Hardware 3 Cable (twist pair + 접지) 5) Constitution of junction box Item Camera control 1 In/Out Camera ↔Junction box ↔Sub key RS-485+ Camera data + RS-485- Camera data - RS-422+ RS-422GND RS-485+ Camera data + RS-485-
Pin no.
9. Quick References OPERATION 〔 Keyboard 1-255〕+〔CAM〕 Power Supply ON +〔SET〕 FUNCTION Function Input Main Sub Select Camera ◎ ◎ Initiative Controller Setting ◎ ◎ ◎ ◎ [SET] Start Set Mode [SET]+[J.
[7]+[MENU]+[ON] [7]+[MENU]+[OFF] Executing the Spiral Surveillance Stop the Spiral Surveillance ◎ [8]+[MENU]+[ON] [8]+[MENU]+[OFF] Executing the PTZ Trace Stop the PTZ Trace ◎ [9]+[MENU]+[ON] [9]+[MENU]+[OFF] PTZ Trace Memorizing Deleting the PTZ Trace ◎ Reset of Selected Camera ◎ [Keypad1~255]+[CAM]+[10]+[MENU]+ [ENT] [20]+[MENU] Joystick up/down +[CLR] LCD Brightness Control Cancellation of Brightness Control ◎ ◎ [STAUS] [STAUS] Executing the Freeze Stop the Freeze ◎ ◎ [1]+[STATUS] Con
DISTRIBUTED BY
