D-Link DVG-2001S VoIP Terminal Adapter Manual Building Networks for People Ver 1.
Contents Package Contents........................................................................................................... 1 Introduction ..................................................................................................................... 1 Connections .................................................................................................................... 2 LEDs ............................................................................................................
Help............................................................................................................................ 26 Technical Specifications .............................................................................................. 27 Frequently Asked Questions .......................................................................................
Package Contents • • • • • D-Link DVG-2001S VoIP Terminal Adapter Power Adapter - DC 12V, 1.2A Manual and Warranty on CD Quick Installation Guide Ethernet Cable (the DVG-2001S’s Ethernet port is Auto-MDIX) If any of the above items are missing, please contact your reseller. Note: Using a power supply with a different voltage rating than the one included with the DVG-2001S will cause damage and void the warranty for this product.
Connections The Ethernet Port (LAN) is auto MDI/MDIX, meaning you can use either a straight-through or a crossover Ethernet cable. Power Adapter Phone Connection Connect your 12V 1.2A power adapter here. Connect to your phone using standard phone cabling. Factory Reset button Auto MDI/MDIX LAN Port Connect the Ethernet cable from computers on your LAN to this port.
LEDs Phone LED This LED will light when a telephone is off the hook. A blinking LED indicates an incoming call is detected Power LED LAN LED A solid light indicates a valid connection to the power supply. An active LED indicates a link has been established. A blinking LED indicates activity on the LAN port.
Features One Foreign Exchange Subscriber (FXS) POTS port (RJ-11 Jack) One NWay 10/100BASE-TX Fast Ethernet port for network connection Voice Activity Detection (VAD)/Comfort Noise Generation (CNG) Silence suppression to reduce bandwidth consumption Adaptive jitter buffer for smooth voice reception Lost packet recovery ability for improved voice quality Support QoS (Quality of Service) for voice quality guarantee Built-in PPPoE function to support dial-up connection for broadba
Using the Configuration Wizard 10.1.1.1 Whenever you want to configure your network or the DVG-2001S, you can access the Configuration Menu by opening the web-browser and typing in the IP Address of the DVG-2001S. The DVG-2001S default IP Address is shown to the right: • • • • • Open the web browser Type in the IP Address of the Router (http://10.1.1.1) Type admin in the User Name field Type admin in the Password field Click OK The Home > Wizard screen will appear.
Home > WAN > Dynamic IP Address Dynamic IP Address Choose Dynamic IP Address to obtain IP Address information automatically from your ISP. This option should be selected if your ISP has not supplied you with an IP address. This option is commonly used for Cable modem services. Host Name The Host Name is optional but may be required by some ISPs. The default host name is the device name of the VoIP Terminal Adapter and may be changed.
Primary/Secondary DNS Address Enter a DNS Address if you wish not to use the address provided by your ISP. Home > WAN > Static IP Address Static IP Address Choose Static IP Address if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x).
IP Address Input the public IP Address provided by your ISP. Subnet Mask Input your Subnet mask. (All devices in the network must have the same subnet mask.) Default Gateway Input the public IP address of the ISP to which you are connecting. Primary DNS Address Secondary DNS Address Input the primary DNS (Domain Name Server) IP address provided by your ISP This is an optional DNS Address entry to be used if the primary DNS Fails.
PPPoE Choose this option if your ISP uses PPPoE. (Most DSL users will select this option.) User Name Enter The PPPoE user name provided to you by your ISP. Password Enter The PPPoE password provided to you by your ISP. Retype Password Retype the password entered in the previous field. IP Address This displays the current IP address. Primary DNS Address Input the primary DNS (Domain Name Server) IP address provided by your ISP.
Secondary DNS Address This is an optional DNS Address entry to be used if the primary DNS fails. Click Apply to set any changes made to the memory of the VoIP Terminal Adapter. Click Connect to initiate a PPPoE connection. Click Disconnect to end a PPPoE connection.
Advanced > VOIP > Server Configuration The VoIP Terminal Adapter can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). The screen shown to the right, along with those on the following pages are used to configure your router to communicate with the devices that will send and receive telephone calls over the Internet. Server FQDN Use this drop-down menu to Enable or Disable the Server Fully Qualified Domain Name (FQDN) function.
Select TEL-URL to have the router use the SIP number without a domain name in the SIP messages that it sends. User Parameter Phone You can set this to Enabled or Disabled. This determines whether or not the phone number is appended to the information forwarded to your SIP server. Your VoIP service provider will instruct you on which setting to use. Caller ID Delivery You can set this to YES or NO. This determines whether CID is received. Display CID You can set this to Enabled or Disabled.
Advanced > VOIP > Provisioning Provisioning is a function that automatically updates your DVG-2001S’s VoIP configuration by using a TFTP server located on the Internet. If you have accesses to such a service, you will need to know the URL and Proxy Address of the Provisioning Server. Provisioning Function Use this drop-down menu to enable or disable the Provisioning Function on the VoIP Terminal Adapter. SSL Use the drop-down menu to enable Secure Shell (SSL).
Advanced > VOIP > STUN Configuration Simple Traversal of UDP over NAT (STUN) − is a protocol that enables a VoIP device, such as this router or an IP phone, to detect the presence and type of NAT behind which the phone is placed. This router supports STUN and can intelligently modify the private IP address and port in its SIP/SDP message by using the NAT mapped public IP address and port through a series of STUN queries against a STUN server located on the public Internet.
Advanced > VOIP > User Agent The VoIP Terminal Adapter can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). Same Phone Number Use this field to enable or disable the use of the same telephone number for the User Agent as for the Server Agent. Index Use this field to assign the telephone socket (on the back of the router) to the information entered in the User Agent. Phone Number The telephone number assigned to the User Agent.
Advanced > VOIP > Peer to Peer The VoIP Terminal Adapter can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). Index This field assigns the telephone socket (on the back of the router) to the information entered in the User Agent. Phone Number The telephone number assigned to this entry. User IP Address Enter the IP address of the remote peer in this field. Port Enter the UDP port number the remote peer will use to make the connection in this field.
Advanced > VOIP > Telephony The VoIP Terminal Adapter can be configured to handle voice signals over the Internet Protocol (Voice Over IP − VOIP). DTMF Method Out-of band Dual Tone Multi-frequency – The Dual Tone Multi-frequency (DTMF) mode sets how the router will handle the tones that your telephone makes when you push its buttons. It is recommended that you use the same mode that your VoIP service provider uses. Select Enabled (RFC 2833) to send the DTMF tones in RTP packets. Select Disabled (G.
Advanced > Misc. Signaling ToS Signaling ToS -ToS field value in UDP IP Packets carrying a SIP Message RTP ToS RTP ToS - ToS field value in UDP IP Packets carrying a RTP data Receive Gain Used to raise or lower the gain (volume) of signals that come in from the IP and are sent to the line-side or trunk-side interface. The Rx Gain dB level may be set in 0.5 db increments from –20 dBm to 20 dBm.
Tools > Admin Change System Password To change the password used to access the web manager, type the New Password and Confirm Password to be certain you have typed it correctly. Click the Apply button to activate the new password. The System User Name remains “admin”, this cannot be changed using the web manager interface. Be sure to save the new setting. Administrator admin is the Administrator login name. Password Enter the password here and the same password in the Confirm Password field.
Tools > System Reset to Factory Default Click Reset to Factory Default to restore the settings.
Tools > Firmware You can upgrade the firmware of the VoIP Terminal Adapter here. Make sure the firmware you want to use is on the local hard drive of the computer. Please check the D-Link Support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site. Firmware Update Click on the link in this screen to find out if there is an updated firmware; if so, download the new firmware to your hard drive.
Tools > Config This screen allows you to backup and restore configuration files. Click Backup to initiate the backing up of a configuration file. Click Upload to initiate the uploading of the configuration file once you have located it by using the Browse button. Tools > Save & Reboot This screen allows you to save and reboot the VoIP Terminal Adapter. Click the Reboot button.
Status > Device Info This page displays the current information for the DVG-2001S. WAN MAC Address: MAC address of the DVG-2001S IP Address: WAN/Public IP Address Subnet Mask: WAN/Public Subnet Mask Default Gateway: WAN/Public Gateway IP Address Status > Stats The VoIP Terminal Adapter keeps a running log of events and activities occurring on the device. If it is rebooted, the logs are automatically cleared. You may save the log files under Log Settings.
The screen above displays the Traffic Statistics. Here you can view the amount of packets that pass through the DVG-2001S on the WAN port. The traffic counter will reset if the device is rebooted or can be reset by clicking the Reset button. To refresh current statistics, click the Refresh button.
Status > Cable Tester The VoIP Terminal Adapter offers you to conduct a Ping test by entering the IP address in the field below and then clicking the test button. .
Help The Help tab will give basic information referring to various screens located in the VoIP Terminal Adapter. To view a specific section, click on its hyperlinked name. A new window of information will appear.
Technical Specifications Standards: IEEE 802.3 IEEE 802.3u Device Management: HTTP 1.
Technical Specifications H = 1.22 inches (31 mm) Security: User Authentication Administration – Username/Password control for Telnet and Web configuration SIP Authentication Provisioning Security using HTTPS and SSL/TLS client certificate encryption and authentication VoIP NAT Traversal – SIP/STUN Miscellaneous: PPPoE (RFC 2516) Power Input: Ext. Power Supply DC 12V, 1.2A Weight: 0.
Frequently Asked Questions Why can´t I access the web based configuration? When entering the IP Address of the DVG-2001S (10.1.1.1), you are not connecting to the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to connect to the web-based utility, however. To resolve difficulties accessing a web utility, please follow the steps below.
Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) What type of cable should I be using? (continued) What´s the difference between a crossover cable and a straight-through cable? The wiring in crossover and straight-through cables are different. The two types of cable have different purposes for different LAN configurations. EIA/TIA 568A/568B define the wiring standards and allow for two different wiring color codes as illustrated in the following diagram.
Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) When to use a crossover cable and when to use a straight-through cable: Computer to Computer – Crossover Computer to an normal port on a Hub/Switch – Straight-through Computer to an uplink port on a Hub/Switch – Crossover Hub/Switch uplink port to another Hub/Switch uplink port – Crossover Hub/Switch uplink port to another Hub/Switch normal port – Straight-through 31
Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) S t e p 2 Disable any Internet security software running on the computer. Software firewalls like Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, etc. might block access to the configuration pages. Check the help files included with your firewall software for more information on disabling or configuring it. S t e p 3 Configure your Internet settings. Go to Start>Settings>Control Panel.
Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) S t e p 4 Check your IP Address. Your computer must have an IP Address in the same range of the device you are attempting to configure. Most D-Link devices use either 10.0.0.1 or the 192.168.0.X range. How can I find my IP Address in Windows 95, 98, or ME? Step 1 Click on Start and then click on Run. Step 2 The Run Dialogue Box will appear. Type winipcfg in the window as shown then click OK.
Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) Step 4 After selecting your adapter, it will display your IP Address, subnet mask, and default gateway. Step 5 Click OK to close the IP Configuration window. S t e p 4 (continued) Check your IP Address. Your computer must have an IP Address in the same range of the device you are attempting to configure. Most D-Link devices use either 10.0.0.1 or the 192.168.0.X range.
Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) How can I find my IP Address in Windows 2000/XP? Step 1 Click on Start and select Run. Step 2 Type cmd then click OK. Step 3 From the Command Prompt, enter ipconfig. It will return your IP Address, subnet mask, and default gateway Step 4 Type exit to close the command prompt.
Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) S t e p 4 (continued) Check your IP Address. Your computer must have an IP Address in the same range of the device you are attempting to configure. Your D-Link device uses 10.1.1.1. Make sure you take note of your computer´s Default Gateway IP Address. The Default Gateway is the IP Address of the D-Link VoIP Terminal Adapter. By default, it should be 10.1.1.1.
Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) How can I assign a Static IP Address in Windows 2000? (continued) Click “Use the following IP Address” and enter an IP Address that is on the same subnet as the LAN IP Address on your VoIP Terminal Adapter. Example: If the VoIP Terminal Adapter´s LAN IP Address is 10.1.1.1, make your IP Address 10.x.x.x where x = 2-254. Make sure that the number you choose is not in use on the network.
Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) How can I assign a Static IP Address in Windows 98/Me? Step 1 From the desktop, right-click on the Network Neighborhood icon (Win ME My Network Places) and select Properties. Highlight TCP/IP and click the Properties button. If you have more than one adapter, then there will be a TCP/IP “Binding” for each adapter. Highlight TCP/IP > (your network adapter) and then click Properties.
Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) How can I assign a Static IP Address in Windows 98/Me? (continued) Step 2 Click Specify an IP Address. Enter in an IP Address that is on the same subnet as the LAN IP Address on your VoIP Terminal Adapter. Example: If the VoIP Terminal Adapter´s LAN IP Address is 10.1.1.1, make your IP Address 10.x.x.x where x is between 2-254. Make sure that the number you choose is not in use on the network.
Frequently Asked Questions (continued) Why can´t I access the web based configuration? (continued) S t e p 5 Access the web management. Open your web browser and enter the IP Address of your D-Link device in the address bar. This should open the login page for the web management. Follow instructions to login and complete the configuration.
Frequently Asked Questions (continued) How can I setup my router to work with a Cable modem connection? S t e p 1 Power cycle the cable modem and router: Turn the cable modem off (first). Turn the router off Leave them off for 2 minutes.** Turn the cable modem on (first). Wait until you get a solid cable light on the cable modem. Turn the router on. Wait 30 seconds. ** If you have a Motorola (Surf Board) modem, leave off for at least 5 minutes.
Frequently Asked Questions (continued) How can I setup my router to work with Earthlink DSL or any PPPoE connection? Make sure you disable or uninstall any PPPoE software such as WinPoet or Enternet 300 from your computer or you will not be able to connect to the Internet. S t e p 1 Upgrade Firmware if needed. (Please visit the D-Link tech support website at: http://support.dlink.com for the latest firmware upgrade information.) S t e p 2 Take a paperclip and perform a hard reset.
Frequently Asked Questions (continued) How can I setup my router to work with Earthlink DSL or any PPPoE connection? (continued) Step 7 Turn off your DSL modem for 2-3 minutes. Turn back on. Once the modem has established a link to your ISP, plug the power back into the D-Link VoIP Terminal Adapter. Wait about 30 seconds and log back into the router. Step 8 Click on the Status tab in the web configuration where you can view the device info.
Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product. U.S. and Canadian customers can contact D-Link technical support through our website, or by phone.
