Table of Contents Table of Contents Product Overview......................................................... 4 Package Contents.................................................... 4 System Requirements.............................................. 4 Introduction............................................................... 5 Features.................................................................... 6 Hardware Overview.................................................. 7 Front View.......................
Table of Contents Storing non-English Character Files........................ 71 Replacing or Adding a New Hard Drive.................... 72 Contacting Technical Support................................... 73 GNU/Linux GPL........................................................... 74 GNU General Public License.................................. 75 Warranty......................................................................
Section 1 - Product Overview Product Overview Package Contents D-Link DNS-343 4-Bay Network Storage Enclosure CD-ROM with Manual and Software Quick Installation Guide Power Adapter Power Cable CAT5 Ethernet Cable Note: Using a power supply with a different voltage than the one included with the DNS-343 will cause damage and void the warranty for this product. If any of the above items are missing, please contact your reseller.
Section 1 - Product Overview Introduction The D-Link DNS-343 4-Bay Network Storage Enclosure shares your documents, photos, music, and videos across the network and on the Internet (via FTP server) so family members, friends, or employees can access them. This enclosure, which can hold four 3.5” SATA hard drives of any capacity1, creates a central network point for backing up valuable files. The built-in RAID 12 mirroring technology protects these files from drive failure.
Section 1 - Product Overview Features • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Equipped with one 10/100/1000 Mbps auto-MDIX Gigabit Ethernet LAN port Embedded SATA 3.5” HDD interface 128X64 OLED display screen 4-bay Serial ATA Hard Drive with RAID 0/1/5/JBoD support Supports 2 modes: Open mode and Account mode Supports Static and DHCP IP address assignment Supports Real time clock (RTC) Web-based administrative program is stored in flash ROM of the server.
Section 1 - Product Overview Hardware Overview Front View OLED: This screen displays System Information, HD Status, and Server Status. Power Button Use this button to switch the device on or off. To switch on the device press the button once. To switch off the device hold the button down for 5 seconds. D-Link DNS-343 User Manual Next Button Use this button to display the System Information (system state), HD Status (hard drive state) and Server Status (server status state) on the OLED.
Section 1 - Product Overview Rear Panel (Connections) Drive Eject Levers Use the provided lever to eject the SATA hard drives. Reset Button Press this button down for over 5 seconds to reset the unit to factory defaults. Power Receptacle Connect the supplied power adapter. Drive Eject Levers Use the provided lever to eject the SATA hard drives. D-Link DNS-343 User Manual Cooling Fan The cooling fans are used to cool the hard drives and feature speed control.
Section 1 - Product Overview Using the OLED The DNS-343 network storage enclosure features an OLED that enables the administrator to easily view information about the DNS-343. The OLED display screen displays information about the network connection, hard drive, and server status.
Section 2 - Installation Installation Hardware Setup This section provides unpacking and installation information for the DNS-343. Open the shipping carton for the DNS-343 and carefully unpack its contents. If this is the first time using the DNS-343 or if a new hard disk is installed, use the Easy Search utility located on the Installation CD and follow the instructions for setting up, configuring and formatting the new drive. To install the DNS-343 on your local network, refer to the steps below: 1.
Section 2 - Installation 3. Insert a 3.5” SATA hard drive into an available drive bay. Make sure to align the drive connector to the SATA connector on the bottom edge inside the drive bay of the DNS-343. Gently push the drive in until it connects. 4. Attach the faceplate to the front of the device.
Section 2 - Installation 5. Connect an Ethernet cable to the available Ethernet port. This cable should connect the DNS-343 to your local network via a router or switch, or directly to a computer for configuration. 6. Connect the supplied power adapter to the power receptacle. When a hard disk is installed, the hard disk must first be formatted in the DNS-343 before it can be used.
Section 3 - Configuration Configuration Easy Search Utility When first powered on, during the initial boot sequence, the DNS-343 will wait to be assigned an IP address via DHCP. If it does not receive a DHCP assigned IP address, by default it will have a self-assigned IP address of 192.168.0.32. It is recommended to use the included D-Link Easy Search Utility when accessing and configuring the DNS-343 for the first time.
Section 3 - Configuration Getting Started To run the Easy Search Utility, insert the DNS-343 CD into your CD-ROM drive: Click Easy Search Utility. Select the listed DNS-343 and click the Configuration button. This will launch the computer’s default web browser and direct it to the IP address listed for the device. Make sure the browser is not configured to use a proxy server. The first window that appears will require the user to login for Configuration or Downloads menus.
Section 3 - Configuration The Login screen will appear: Type admin for the username and leave the password field blank. Click Configuration Note: If the web browser is unable to connect to the web manager of the DNS-343, check to make sure your computer is on the same subnet as the DNS-343. For example, if there is no DHCP server active, your computer will need an IP address in the 192.168.0.0 subnet. Your computer should have an IP address of 192.168.0.
Section 3 - Configuration When prompted to configure the Hard Drive Settings: Select from one of the basic types of hard drive configurations below: • Standard • JBOD • RAID 1 • RAID 5 Or select Custom Configuration and then click Next. Note: All data will be erased off the hard drives installed in the DNS-343 during the format process! A warning message appears informing you that your drives will be formatted and all data will be erased. Click OK to continue.
Section 3 - Configuration When the formatting completes, the Format Results screen will appear. Click Restart to finish the format procedure. Then click OK to confirm and restart the DNS-343. Press OK to restart the DNS-343. When the system restarts you will be prompted to login to the DNS-343.
Section 3 - Configuration Web UI After login, you will be redirected to the DNS-343 web UI: The DNS-343 web UI defaults to the Setup page. The main categories for configuration are located in the menu tabs at the top of the page. These categories include: Setup - Contains the DNS-343 setup Wizard, LAN Setup, Time and Date settings and Device settings. Advanced - Allows the DNS-343 administrator to configure RAID options, Users, groups of users and their storage quotas.
Section 3 - Configuration Setup Wizard The DNS-343 has a setup Wizard that allows you to configure the basic settings for your device. When running the DNS-343 setup wizard, the welcome screen displays a summary of the five steps of the wizard. Click Next to continue. It is recommended that you set an admin password to access the web manager. Type a New Password in the space provided and type it again in the Confirm Password space. Click Next to continue.
Section 3 - Configuration Choose your Time Zone from the drop-down menu. Click Next to continue. Configure the IP settings for your device. If you are using a DHCP server such as a router on your network, the DNS-343 will automatically obtain the IP settings. If you prefer to assign a Static IP address, select Static IP and enter the network setting for your device. Click Next to continue.
Section 3 - Configuration Enter the workgroup, name, and description for your DNS-343, or leave the default values and click Next to continue. Click Back to make changes or click Restart to save your settings and reboot the DNS-343.
Section 3 - Configuration When the login prompt appears, login using the new administrator password. Then click Configuration to access the configuration page of your DNS-343.
Section 3 - Configuration LAN In this section, you can configure the LAN settings for your DNS-343. Link Speed The LAN Link Speed is set to Auto by default, but can be manually set to 100Mbps or 1000Mbps. DHCP Client Select DHCP Client to obtain an IP address from your DHCP server. Static IP Select Static IP to assign the IP information for the DNS-343 manually. Jumbo Frames The DNS-343 can support Jumbo Frames that are between 3000 and 9000 bytes in size.
Section 3 - Configuration Time and Date The system time and date can be set manually or configured from an NTP server. Time Zone Select your time zone from the drop-down menu. NTP Server Network Time Protocol (NTP) synchronizes the DNS-343 with an Internet time server. D-Link provides two time servers for your convenience. Choose the one closest to your location. From My Computer This option will synchronize the DNS-343 clock with your computer.
Section 3 - Configuration Device Settings This section allows you to assign a workgroup name, name, and a description to the DNS-343. Workgroup The Workgroup is used by Microsoft ® Windows Network to organize available network groups within the same network. Name The unique Name appears for other network services including shared libraries on iTunes® and other media players. The name can be used to access your device from a web browser instead of using an IP address, for example, http://dlink-xxxxxx.
Section 3 - Configuration Advanced RAID RAID, short for Redundant Array of Independent Disks, is a combination of two or more disks with the aim of providing fault tolerance and improving performance. There are several different levels of RAID, with each one providing a different method of sharing or distributing data among the drives. RAID 0 RAID 0 provides data striping, which spreads out blocks of data over all drives, but does not provide data redundancy.
Section 3 - Configuration RAID 5 provides data striping with distributed parity, which stores information that can be used to reconstruct data. A RAID 5 array will be the size of all the combined disks capacity less the capacity of one disk, e.g. If there are 4x 80GB disks in the array, the arrays capacity will be 240GB (3x80GB). Implementing RAID 5 on the DNS-343 allows it to continue operating even if one of the disks fails. The diagram below indicates the operation of RAID 5.
Section 3 - Configuration The DNS-343 supports the following configuration types: Standard, where each drive is a unique volume, JBOD, which combines both drives in a linear fashion to create one volume, RAID 1 and RAID 5 with a Basic Configuration and a combination of RAID 0/JBOD, RAID 1/JBOD and RAID 5/JBOD for Custom Configuration. Click Re-configure All Existing Hard Drive(s) to setup the RAID configuration.
Section 3 - Configuration Users and Groups The Users/Groups menu is used to create and manage user and group accounts. These are used for user access and read/write privileges for specified folders on the network drive (using the Network Access menu), or to setup FTP access and privileges. Up to 64 users and 10 groups can be created. By default all users have read and write access to all folders but access rules can be created in the Network Access menu.
Section 3 - Configuration The user is now listed in the Users in group list. To delete a user from a group, under Group Setting: • Select the group • Highlight the user to be removed • Click the <
Section 3 - Configuration Quotas The DNS-343 supports storage quotas for both groups and individual users. Assigning a quota to a group or user will limit the amount of storage they are allocated. By default, users and groups do not have a quota. User Quota Settings User quotas are displayed here. Quotas can be edited by clicking on the notepad icon. Group Quota Settings Group quotas are displayed here. Quotas can be edited by clicking on the notepad icon.
Section 3 - Configuration Configuring Quotas All users and groups are automatically listed on this page, and cannot be deleted. The default quota setting is “Unlimited”. To add a quota for a particular user or group, you must perform the following: Click the notepad icon of the user you want to add a quota to. Set a quota amount (MB) for the user and click Apply.
Section 3 - Configuration This screen will display and indicate all updated quota settings.
Section 3 - Configuration Network Access This section allows you to assign the access rights for your users and groups to specific folders or volumes. By default, all volumes are open to anyone on the local network with read/write access. Before specific user or group rules can be created, the default rules must be deleted. Network Access Settings Assign permissions for users and groups on the local network here. Category Determines whether the access rule will apply to a group or individual user.
Section 3 - Configuration By default Windows® Vista™ has Oplocks enabled and can not be disabled. If you are having network performance issues with applications sharing files from the DNS-343 you may try to improve performance by setting Oplocks to No(off). Map Archive Comment Network Access List When enabled, the file attribute ”Archive” will be copied as the file is being stored on the DNS-343. Certain backup software attach this attribute to files that are being stored as backups.
Section 3 - Configuration FTP Server FTP Server Settings The DNS-343 is equipped with a built in FTP Server. The server is easy to configure and allows up to 10 users to access the server locally or remotely at the same time. FTP Server Settings This section contains the configuration settings for the DNS-343 FTP Server. Category Determines whether the FTP server rule will apply to an individual user or a group. User / Group Select the group or user the FTP server rule will apply to.
Section 3 - Configuration FTP Server Status FTP Access List Displays users and/or groups that have access and their user rights. Status Displays if the FTP server is started or stopped. Port Max User Flow Control Displays the FTP Port. Displays the maximum number of users. Displays the flow control status. Idle Time Displays the idle time before disconnecting the user. Client Language Displays the client language set for this FTP server.
Section 3 - Configuration FTP Server Behind a Router If you are behind a router, you will need to forward the FTP port from the router to the DNS-343. Additional filtering and firewall settings may need to be modified on your router to allow FTP Access to the DNS-343 from the Internet. Once the port has been forwarded on the router, users from the internet will access the FTP server through the WAN IP address of the router.
Section 3 - Configuration UPnP AV Server The DNS-343 supports media streaming service to UPnP AV compatible clients on the local network. Use the UPnP AV Server menu to select the media content made available to such clients. By default the UPnP server is enabled. The root checkbox specifies access to media content on all volumes and folders on the drive. Click on the Save Settings button to apply and save the new settings.
Section 3 - Configuration iTunes Server The DNS-343 features an iTunes Server. This server provides the ability to share music and videos to all the available computers within your local network. If the server is enabled, the DNS-343 will be automatically detected by the iTunes program, and the music and videos contained in the specified directory will be available to stream over the network. iTunes Server Select Enable or Disable to enable or disable the DNS-343 iTunes server.
Section 3 - Configuration After enabling the iTunes server on the DNS-343, launch iTunes. When iTunes detects the DNS-343, select it and you will be prompted to enter the iTunes server password if required. Select the DNS-343. When prompted, enter in the iTunes server password. Click OK. Media stored on the DNS-343 will then be available for use in iTunes.
Section 3 - Configuration DHCP Server The DNS-343 can be used as a DHCP Server. As a DHCP server, it can be used to serve IP addresses to devices on your local network. However, this feature should not be enabled if you already have a DHCP server, such as a router on your local network. DHCP Server Enables or Disables the DNS-343 DHCP Server. Starting IP Address Enter the starting IP address for the range of addresses assigned by the DHCP server.
Section 3 - Configuration Maintenance Change Admin Password The Admin menu allows you to set a password for your admin account. It is recommended to set an admin password when first configuring your DNS-343. User Name The administrator user name is admin, and this cannot be changed. Password Enter the current password. (Leave this blank if you have not set a password yet.) New Password Confirm Password Enter a new password. Enter the new password again for confirmation.
Section 3 - Configuration System The DNS-343 System menu provides options to perform a system restart, save and load configuration settings, and set idle times. Restart Defaults Shutdown Click Restart to reboot the DNS-343. Click Restore to reset the DNS-343 to its factory default settings. This will erase all previous configuration changes. Click Shutdown to turn off the DNS-343. Configuration Settings Click Save to save the current DNS-343 configuration settings to a file on the local computer.
Section 3 - Configuration Firmware This section allows you to check for new firmware releases and upload them to your device. To upgrade the DNS-343 firmware, go the D-Link Support Page and download the latest version. When the download is completed, use the Browse button to locate the firmware file on your computer and click the Apply button to begin loading the firmware to your device.
Section 3 - Configuration E-Mail Alerts With the DNS-343 E-Mail Alerts, you can configure e-mails to be sent alerting you to certain operational conditions and drive status conditions. These alerts can prove helpful with the management and safeguarding of important data. Alert Settings This section contains the configuration settings for your e-mail account and alert preferences.
Section 3 - Configuration E-Mail Alert Settings Login Method Select either Account or Anonymous. Choosing Anonymous does not require a User Name or Password. User Name Enter the appropriate user name for your e-mail account. Password Enter the appropriate password for your e-mail account. SMTP Server Enter the IP address or domain name of your outgoing mail server. If you are unsure of this value, contact your e-mail provider. Sender E-Mail Enter the “from” e-mail address (e.g. aler ts@dns323.
Section 3 - Configuration E-Mail Alert Types Space Status Select an interval in hours and minutes to have a status of space remaining on the drives e-mailed. A Volume Is Full An alert will be sent when the hard drive is full. Administrator Password Change An alert will be sent if the admin password is changed. Firmware Upgraded An alert will be sent if the firmware is upgraded. System Temperature Exceeded An alert will be sent if the DNS-343 device temperature exceeds the set threshold.
Section 3 - Configuration Power Management The DNS-343 Power Management feature allows you to configure the drives to shut down after a specified idle time. The drives will power up again when data is accessed. Power Management Turn off Hard Drives Select Enable or Disable. Set the amount of time before idle drives will shut down. Click Save Settings to apply the settings.
Section 3 - Configuration Dynamic DNS The DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can use the domain name to connect to your server no matter what your IP address is. DDNS Select Enable or Disable.
Section 3 - Configuration LCD Display The LCD Display settings allow the administrator to change the time it takes for the OLED screen on the front of the DNS-343 to power off. Click on the drop-down box below to change the time it takes for the OLED screen to power off.
Section 3 - Configuration Disk Utility The Disk Utility allows the administrator to perform a standard Scan Disk check for errors on the hard disk, select the volume from the drop-down menu and then click the Scan Disk button. Any errors found will be listed along with a description and the available repair options.
Section 3 - Configuration Status Device Information LAN Info Displays the local network settings of the DNS-343. Device Info Displays the workgroup, name, description and current temperature of the DNS-343. Printer Info Displays information for a connected USB printer. If your computer is having problems printing to the DNS-343, you can click the Clear Print Queue(s) button to remove any print jobs that may be causing your computer to be unable to print.
Section 3 - Configuration Connecting a UPS to the DNS-343 When a UPS (Uninterruptible Power Supply) USB management connection is connected to the DNS-343, the Status screen hides the printer information and displays information about the UPS connected. The screenshot below shows the Status screen when a UPS is attached to the DNS-343. UPS Info The UPS Information screen displays information about the UPS Manufacturer and the Product name.
Section 3 - Configuration Support The DNS-343 Support page provides a menu of Support topics explaining the features of the device.
Section 3 - Configuration Mapping a Drive You can use the D-Link Easy Search Utility to map drives to your computer. Insert the DNS-343 CD into your CD-ROM drive. Click Easy Search Utility. The Easy Search Utility will load and detect any DNS-343 devices that are on the local network.
Section 3 - Configuration If the name of your DNS-343 does not display in the device list, click Refresh. Highlight an available DNS-343. Available volumes will be displayed under Drive Mapping. Highlight the volume you want to map. Select an available drive letter from the drop-down menu and click Connect. Once connected, your mapped drive(s) will appear in My Computer.
Section 3 - Configuration Double-click the My Computer icon on your desktop. Double-click on the mapped drive to access the files and folders.
Section 3 - Configuration Download Scheduling The DNS-343 Download Scheduling feature allows you to set up scheduling folder or file downloads and backup sessions. Begin by accessing the configuration page of your DNS-343: Click Easy Search Utility. Highlight an available DNS-343 and click Configuration to access the web-based utility.
Section 3 - Configuration The DNS-343 login screen will appear: Type admin for the username and leave the password field blank. Click Schedule Downloads. The DNS-343 Download Scheduling configuration will appear.
Section 3 - Configuration Schedule Downloads Scheduling Settings Configure download and backup schedules here. Refer to the next page for more information. Schedule List The Schedule List will display all completed, active, and pending scheduled downloads and backups.
Section 3 - Configuration Scheduling Settings Login Method Select the appropriate login method to access the files for download. If the site requires login credentials, select Account and enter a valid username and password. Type Select File or Folder, depending on what you want to download or backup. URL Enter the URL of the site or server you are initiating a transfer from. E.g. ftp://123.456.789/Test ftp://123.456.789/test.txt http://www.test.com/test.
Section 3 - Configuration USB Print Server The DNS-343 features a built-in USB print server, giving users the ability to share a printer on their local network. Connect a USB printer to the USB port on the back of the DNS-343. It is important to ensure that all the printer’s drivers have been installed on the computer(s) you want to print from. To add a printer: Click Start, and select Printers and Faxes.
Section 3 - Configuration Select “Add a printer”. The Windows® Add Printer Wizard will launch: Click Next to continue.
Section 3 - Configuration When prompted to choose a local, or network printer, select “A network printer, or a printer attached to another computer.” Click Next to continue. Select “Browse for a printer” and click Next to continue.
Section 3 - Configuration Double-click “DNS-343” from the Shared Printers list to expand the tree. Select the available USB printer, and click Next to continue.
Section 3 - Configuration The following printer driver messages will appear: Click Yes to continue. Click OK to continue and select a printer driver. Select the appropriate printer driver from the list and click OK to complete the wizard. If the driver is not in the list, select Have Disk.
Section 3 - Configuration Insert the print driver CD or browse to the appropriate directory. Select the appropriate driver file, and click Open to continue. Click OK to continue.
Section 3 - Configuration Verify the driver is correct, and click OK to continue. The wizard will install the printer drivers, and return a completion screen. Click Finish.
Section 3 - Configuration The printer should now appear as an available printer.
Section 3 - Configuration Storing non-English Character Files By default the DNS-343 supports Unicode which is an industry standard allowing computers to consistently represent and manipulate text expressed in most of the world’s writing formats.
Section 3 - Configuration Replacing or Adding a New Hard Drive It is recommended that you backup your important files before replacing or adding a new hard drive to the DNS-343. Replacing a Hard Drive: Please make sure the power is off before replacing a hard drive. After you install the new drive, turn on the DNS-343 and then connect to the Web UI. The DNS-343 will prompt you to format the new drive. Refer to page 15.
Appendix A - Contacting Technical Support Contacting Technical Support U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. Before you contact technical support, please have the following ready: • Model number of the product (e.g. DNS-343) • Hardware Revision (located on the label on the bottom of the device (e.g. rev A1)) • Serial Number (s/n number located on the label on the bottom of the device).
Appendix B - Warranty GNU/Linux GPL • “GPL Software” means GPL software licensed to you under the GNU General Public License as published by the Free Software Foundation (GPL). A copy of the GPL is included below. • “Open Source Software” means various open source software components licensed under the terms of applicable open source license agreements included in the materials relating to such software.
Appendix B - Warranty GNU General Public License Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
Appendix B - Warranty Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow.
Appendix B - Warranty b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
Appendix B - Warranty The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable.
Appendix B - Warranty It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices.
Appendix B - Warranty 12.
Appendix B - Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Appendix B - Warranty Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation.
Appendix B - Warranty • After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship back any accessories.
Appendix B - Warranty IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT.
Appendix B - Warranty CE Mark Warning: This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
