DP-101P+ Multi-protocol Ethernet Pocket Size Print Server User’s Manual Rev.
DP-101P+ Print Server User’s Manual TABLE OF C ONTENTS 0 ABOUT THIS GUIDE ............................................................................... 3 1 INTRODUCTION ...................................................................................... 4 SERVICE FEATURES ....................................................................................... 4 EXTERNAL FEATURES ................................................................................... 6 Front End...............................
DP-101P+ Print Server User’s Manual 0 A BOUT THIS G UIDE This manual describes the D-Link DP-101P+ Multiprotocol Ethernet Print Server, including full descriptions of its features, detailed installation procedures, and troubleshooting information. Your DP-101P+ package includes important software components, and additional user manuals. The software components, and procedures for installation and setup of the software, are covered in the PS Admin User’s Guide.
DP-101P+ Print Server User’s Manual 1 1 I NTRODUCTION The DP-101P+ Print Server is a compact pocket-sized print server which connects your Ethernet network directly to your printer, wherever it is. It manages the flow of print files from your workstations or file servers to its connected printers, delivering print jobs to high-performance printers much faster than a file server or a PC acting as a print server can.
DP-101P+ Print Server User’s Manual ♦ Because the DP-101P+ is very portable (pocket-sized) and inexpensive compared to a PC-based print server, and because the DP-101P+ connects to your file servers through the network, the printer can be stationed at the location of maximum convenience to users. The DP-101P+ offers extraordinary flexibility, operating with all major network operating systems and protocols: ♦ TCP/IP UNIX lpr/lpd (HP-UX, SunOS, Solaris, SCO, UnixWare, IBM AIX) Windows NT/2000 NetWare 5.
DP-101P+ Print Server User’s Manual External Features This section describes the external features of the DP-101P+ print server. Front End The network port, power input socket, and LED indicators are all located at the front. Network Port Led Indicators DC Power Input DP-101P+ Front End Network Port The network port (RJ-45 receptacle) provides for connection to the network through 10Base-T Ethernet cabling. DC Power Input The DC power input socket uses a 7.5V power supply.
DP-101P+ Print Server User’s Manual LED Indicators The front of the DP-101P+ includes three LED indicators. See "Power-up and Self-Test," Chapter 2, for LED indications upon starting up the DP-101P+. During operations following a normal startup, the LED indicators provide the following status signals: ♦ Pw/Tx Steady or flashing green confirms power on. This indicator blinks (briefly dark) when the DP-101P+ is transmitting to the network.
DP-101P+ Print Server User’s Manual Printer Port The printer port, is configurable by commands in the PS Admin program, or by commands issued to the DP-101P+ via Telnet. See the PS Admin User’s Guide for configuration procedures. The print server also supports web configuration permitting users to configure settings through the web browser. DP-101P+ default IP address as follows: ♦ Default IP address – 192.168.0.1 ♦ Subnet Mask – 255.255.255.
2 2 U NPACKING AND I NSTALLATION This chapter explains how to install your DP-101P+ print server and connect it to the network. It also describes the automatic power-on self test. Unpacking and Inspecting Carefully remove all items from the package.
DP-101P+ Print Server User’s Manual Installing the DP-101P+ Follow these steps for a trouble-free start of print-server operations with your DP-101P+. Please take particular notice of the warning in step 4: the network connection should be made before supplying power to the DP-101P+. 1. Confirm proper operation of the printer to be connected to the DP-101P+. 2. When you have confirmed proper operation of the printer, switch its power off. 3. Confirm that your network is operating normally. 4.
DP-101P+ Print Server User’s Manual Power-up and Self-Test Whenever the DP-101P+ is powered up, two kinds of testing procedures follow automatically. The first procedure is just a programmed series of LED flashes, to confirm proper operation of the three LED indicators. The second procedure comprises programmed tests of each of the DP-101P+'s major components. If any fault is found during the component test series, testing is halted and a continuous pattern of LED flashes signals the nature of the fault.
DP-101P+ Print Server User’s Manual LPT Flash Pattern Error Type steady long flashes Firmware Reload Required continuous on DRAM Error One long, two short flashes Timer INT Error One long, three short flashes Flash Protected One long, four short flashes Flash ID Error One long, five short flashes Flash Erase / Program Error One long, six short flashes LAN Controller Error One long, seven short flashes LAN Memory Error One long, eight short flashes Parallel Controller Error One long, nin
DP-101P+ Print Server User’s Manual A 3 P RODUCT S PECIFICATIONS Printer Connection Printer Port: IEEE 1284 standard bidirectional parallel interface with 36-pin connector. Bidirectional Communication: Hewlett-Packard PJL (Printer Job Language) standard for bidirectional communication. Network Connection Network Standards: IEEE 802.3 10Base-T Ethernet . Network Data Transfer Rate: Network Connector: connection . 10Mbps (megabits per second) .
DP-101P+ Print Server User’s Manual Management and Diagnostics Standard: SNMP MIBs: MIB-II (RFC 1213) Diagnostic LED Indicators: Pw/Tx, Lk/Rx, LPT Environmental and Physical Power Supply: 500mA Dimensions: Weight: External power supply providing 7.5VDC/ 92.8mm × 58mm × 25.3mm approx.
B 4 P ORT P INOUTS The following table lists the pinouts of the DP-101P+'s 36-pin parallel port connector (identical to the parallel port connector used on most printers.) Signal names beginning with n are active-low signals. Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 ♣ Signal nStrobe Data 1 ♣ Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 Data 8♦ nAck Busy PError Select nAutoFd Not Defined Logic Gnd Chassis Gnd Least Significant Bit Data signals will be driven by some , but not all peripheral devices.
DP-101P+ Print Server User’s Manual 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 16 Peripheral Logic High Signal Ground (nStrobe) Signal Ground (Data 1) Signal Ground (Data 2) Signal Ground (Data 3) Signal Ground (Data 4) Signal Ground (Data 5) Signal Ground (Data 6) Signal Ground (Data 7) Signal Ground (Data 8) Signal Ground (PError, Select, nAck) Signal Ground (Busy, nFault) Signal Ground (nAutoFd, nSelectIn, nInit) nInit nFault Not Defined Not Defined Not Defined nSelectIn P H P H Port
DP-101P+ Print Server User’s Manual 5 AUSTRALIA CANADA CHILE CHINA DENMARK EGYPT FRANCE GERMANY INDIA ITALY JAPAN RUSSIA SINGAPORE S. AFRICA SWEDEN TAIWAN U.K. U.S.A. O FFICES D-LINK AUSTRALASIA Unit 16, 390 Eastern Valley Way, Roseville, NSW 2069, Australia TEL: 61-2-9417-7100 FAX: 61-2-9417-1077 TOLL FREE: 1800-177-100 (Australia), 0800-900900 (New Zealand) URL: www.dlink.com.au E-MAIL: support@dlink.com.au, info@dlink.com.
LIMITED WARRANTY D-Link provides this limited warranty for its product only to the person or entity who originally purchased the product from D-Link or its authorized reseller or distributor.
DP-101P+ Print Server User’s Manual obligation shall be to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional specifications for the Software. Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software.
Products that have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs; Operational adjustments covered in the operating manual for the product, and normal
DP-101P+ Print Server User’s Manual GOVERNING LAW: This Limited Warranty shall be governed by the laws of the state of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This limited warranty provides specific legal rights and the product owner may also have other rights which vary from state to state.
Wichtige Sicherheitshinweise 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den spätern Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssigoder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. 5. Das Gerät is vor Feuchtigkeit zu schützen. 6.
DP-101P+ Print Server User’s Manual Trademarks Copyright 1999 D-Link Corporation. Contents subject to change without prior notice. D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective proprietors. Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems Inc.
Register by mail or online at http://www.dlink.com/sales/reg/ 6 R EGISTRATION C ARD Print, type or use block letters. Your name: Mr./Ms _____________________________________________________________________________ Organization: ________________________________________________ Dept.
DP-101P+ Print Server User’s Manual
