Version 1.
Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date 1.0 July 17, 2013 Description • Initial release for hardware A1 Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
Table of Contents Table of Contents Preface................................................................................. 2 Manual Revisions........................................................................... 2 Trademarks...................................................................................... 2 Product Overview............................................................... 4 Package Contents..........................................................................
Section 1 - Product Overview Product PackageOverview Contents Two PowerLine AV2 600 Gigabit Adapters (DHP-600AV) Two Ethernet Cables Quick Install Guide If any of the above items are missing, please contact your reseller. Minimum Requirements Network Requirements • Windows® 7, Vista® or XP (with Service Pack 3) • Ethernet Network Interface (10/100/1000 Mbps) • PC with 1.
Section 1 - Product Overview Introduction The DHP-601AV is D-Link’s PowerLine AV2 600 Gigabit Starter Kit. It contains two DHP-600AV adapters. The DHP-600AV is a fast, 600Mbps* PowerLine AV2 600 Gigabit Adapter, which allows you to connect your home computers, networking devices, and video game consoles using the most pervasive medium in your home - the existing electrical wiring.
Section 1 - Product Overview Hardware Overview LEDs 1 2 Power LED PowerLine LED • Solid Green: The device is receiving electrical power. • Blinking Green (1time/1 second): The Simple Connect button was pressed. • Blinking Green (1 time/2 seconds): The device is in Power Saving Mode • Off: The device is not receiving electrical power. • Solid: The device is connected to a PowerLine network. • Off: The link is not established with another PowerLine device.
Section 1 - Product Overview Hardware Overview Connection 1 2 1 2 Connect to an Ethernet device such as a router, computer, video game console, network storage device, or a media player. Press and hold the button for two seconds to secure your network. Simple Connect Button/Reset (Refer to “Push Button Security” on page 11 for more information.) Button Hold the button for 10 seconds to reset the device back to the factory default settings.
Section 2 - Hardware Installation Hardware Installation Recommendations • For best results, use in a regular wall outlet without any other devices plugged in. Connecting this product to a power strip or a surge protector may adversely affect the performance of this device. • Avoid using the PowerLine adapters in an electrical outlet that is located near an appliance that uses a lot of power such as a washer, dryer, refrigerator, microwave, hair dryer, or air conditioning unit.
Section 2 - Hardware Installation 2. Plug in the other DHP-600AV adapter in the room that you want to extend your network to. The Power LED will light up. DHP-600AV 3. Verify that the PowerLine LEDs on both adapters are lit. If they are, the adapters are connected. If not, try another wall outlet (closer to the other PowerLine adapter). DHP-600AV DHP-600AV 4. To secure your network, press the Simple Connect button for two seconds on one of the adapters. The Power LED will start to blink.
Section 2 - Hardware Installation 5. You may now connect another device to the DHP-600AV adapter, using an Ethernet cable. Verify that the Ethernet LED is lit. Your hardware installation is complete. Power Saving Mode The DHP-600AV will automatically go into Power Saving Mode when there is no activity for five minutes. The Power LED will blink intermittently while the device is in Power Saving Mode. Note: D-Link PowerLine devices can not be configured while in Power Saving Mode.
Section 2 - Hardware Installation Push Button Security Understanding PowerLine AV2 600 Gigabit Adapter Security PowerLine AV 600 Gigabit Adapters on the same network must use an identical encryption key. The default encryption key of each DHP-600AV is HomePlug AV. All PowerLine AV2 600 Gigabit Adapters with default encryption keys can communicate with each other. It’s recommended that you create a private encryption key for network security purposes.
Section 2 - Hardware Installation 5. Adding More Adapters (Optional) If you would like to add more than two adapters, press the Simple Connect button of the additional adapter for no more than three seconds. The Power LED will start blinking after you release the button. Then press the Simple Connect button of any adapter in your existing PowerLine network for no more than three seconds. The Power LED will start blinking after you release the button.
Section 2 - Hardware Installation PowerLine Installation Considerations Plan the location of your PowerLine devices: 1. Connect PowerLine devices into electrical outlets that are not controlled by a wall switch. This will help you to avoid accidentally turning off power to the device. 2. Do not connect your PowerLine devices to extension cords, surge protectors, or power strips. Doing this might prevent your devices from working correctly, or may reduce network performance. 3.
Section 2 - Hardware Installation Safety Please read all of the safety and operating instructions before using your devices: 1. Do not open the devices or attempt to repair or service them. 2. Use the devices in a dry location, and avoid placing them in humid environments. 3. Do not submerge the devices in liquid or attempt to clean them with liquids or solvents. To clean the devices, disconnect from the power outlet and use a damp towel. 4. Keep the devices out of direct sunlight. 5.
Section 3 - Troubleshooting Troubleshooting If I do not see LEDs light up? If the Power LED is off, make sure the PowerLine devices are plugged into outlets with power. Also make sure the PowerLine devices are not plugged into an extension cord, power strip, or surge protector. If the PowerLine LED is off, the devices are unable to find each other. You can plug in all the PowerLine adapters within the same room in order to determine whether your home’s electrical outlets are suitable.
Appendix A - Technical Specifications Technical Specifications Standards • HomePlug AV2 Compliant • IEEE 802.3 • IEEE 802.3x • IEEE 1901 Operating Temperature • 32° F to 104° F (0° C ~ 40° C) Network Interfaces • One 10/100/1000 Ethernet port • PowerLine Humidity • Operation: 10% ~ 90% non-condensing • Storage: 5% ~ 95% non-condensing AC Input • 100 ~ 240V, 50/60Hz Dimensions • 3.44 x 2.44 x 1.18 inches (87.4 x 62.2 x 30 mm) Security • 128 bit AES data encryption Weight • 0.
Appendix B - Contacting Technical Support Contacting Technical Support U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. Before you contact technical support, please have the following ready: • Model number of the product (e.g. DHP-600AV) • Hardware Revision (located on the label on the bottom of the box (e.g. rev A1)) • Serial Number (s/n number located on the label on the bottom of the box).
Appendix C - Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Appendix C - Warranty Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation.
Appendix C - Warranty • After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package o ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship back any accessories.
Appendix C - Warranty While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link Service Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.
Appendix C - Warranty Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice. Copyright ©2013 by D-Link Corporation/D-Link Systems, Inc.
Appendix D - Registration Registration Register your product online at registration.dlink.com Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.
