2.4GHz Digital Spread Spectrum D-Link 2-line Digital Phone System Dual Dialing Operation Manual 2-line Speakerphone Base and Answering Machine System with Multiple 2-line Handsets CIDCW accessed by Base and Handsets Handsets are expandable up to 8 units *********************************** OD-2LP-500DAM The 2-line Digital Phone with multiple handsets.
＊ OD-2LP-300EH PRODUCT FEATURES When examining your new 2.4G digital phone system, you will find an array of special function including (take OD-2LP-200DAM as example): General Product Function: 1. 2-line 2.4G DSS frequency hopping, multiple handsets extension up to 8 or more than 8 handsets. 2. Two lines available for dialing or conversation/ leaving message on mail boxes by base unit or handset. 3. Line auto selection and line-in-use indicator for each line 4.
23. Handset-to-Handset Intercom without costing on phone 24. Page Finder 25. Pause function on base and handset 26. Flash function on base and handset 27. Hold and Transfer function on base and handset 28. Charging indicator light & paging light 29. Phone Mute 30. Headset Jack 31. Removable Belt clip on handset 32. Tone/Pulse Switch 33. LCD icon indicators: Time/Date, New call, battery power, receiving power gain signal, line 1/line 2 34. user name setting on handset 35.
repeat/skip/speed/delete message/memos) 54. Memory full announce (under the full memory status, user can access messages via remote control) 55. Save/edit/erase messages on ICM 56. Mailbox code setting on system for each of 5 mailboxes 57. assign mailbox number to individual handset 58. Remote operation of TAD and mailbox via handset (through handset remote access code) 59. Setting of voice announcement (ANNOC) 60. Remote operation of TAD and mailbox via outside telephone. 61.
3) answering machine on base, 4) answering machine remote operation via handset, 5) Advance system (Menu) setting, 6) Advance handset (Menu) setting. To enter into Base Menu or Handset Menu, press MENU button at Base or at Handset, 1. To press MEMU 2. Use score UP and DOWN to get functions I.
D-LINK Hopping System Base Menu Tree 01 TIME/DATE 02 RING TONE 01 SET HOUR: 02 SET MIN: 03 SET AM/PM: 04 SET MONTH: 05 SET DAY: 01 RING TONE 1 02 RING TONE 2 Default is 12 12 HOLD TIME 01 CONTINOUS 02 TIME:30SEC 03 TIME:60SEC Default is 00 Default is PM Default is 01 Default is 01 Default 13 HOLD TONE 14 FLASH TIME 03 RING SELECT 04 MSG ALERT 05 ANNOUNCEMENT xx RING TONE n 01 3 RINGS 02 5 RINGS 03 TOLL SAVER 01 ALERT ON 02 ALERT OFF Default 15 PAUSE TIME 10 TIME:1SEC 01 TIME:1SEC 02 TIME:2SEC
HANDSET MENU MENU SKEY 01 REG. HANDSET 02 HANDSET NAME 03 SET MAIL BOX OK OK OK HS NO: PS. HS NO:01~99 03-01 MAIL BOX=01 PS. MAIL BOX= GEN,01~04 IJJ.CD CONFIRMED PS. ADD/EDIT PHONE NAME 04 RING TONE OK *** RING TYPE 01 PS. UP/DOWN KEY SET RING TYPE=01~04 RIGHT/LEFT KEY SET RING VOLUME= *~******** 05 KEY BEEP VOL OK 05-01 KEYBEEP=01 PS. KEYBEEP= OFF,01~07 MENU 06 SET CONTRAST OK 06-01 CONSTRAST=01 PS.
LCD Icon description: Antenna signal: Shows the level of receiving power gain Message Icon (mail symbol): message icon is flashing when calling waiting (type II) come in Call#: Shows total (accumulate) calls of caller ID, the number include the caller ID has been reviewed. NEW Icon: Under idle mode, the NEW call icon will flash slowly when a new Caller ID call has been received. Hour/Min AM/PM: it shows current date& time when idle. Beside the first line of time/date icon.
3. You will hear the ringing sound. 4. The system will automatically assign the free C/O line for dialing out. 5. LINE 1 (or LINE 2) icon is blinking which indicates the line is in use. 6. To end conversation, press EXIT button. Place a regular call from base unit: 1. To lift the corded handphone, 2. Dial the want number, 3. You will hear the ringing sound. 4. to end conversation, put corded handphone back into base cradle.
Note: 1. If you don’t retrieve the call after 30 sec, the call is automatically back to handphone, and base display “ L1 CALLING”. 2. At this time, if handphone is busy when the call is back, the handphone will hear bi-bi sound. Then, the call will be transferred to all handsets (all handsets will ring) 3. If you don’t hang up the handphone after you have put a call on hold, you pick up with another handset extension, the call remains connected to your telephone and is taken off hold.
1. Under Standby mode, press Redial button 2. Press SPEAKER button to dial out. The system will automatically assign the free C/O line for dialing out. The LINE 1 (or LINE 2) icon will be lighted Turning the ringer volume To turn the ringer volume: 1. Press the right shift button. Continue to press the Right Shift ( button until you reach the desired ring volume. To turn the ringer OFF: 1. Press the left shift button. Continue to press the Left Shift button until the ringer is off.
To Set Number of Rings before answering You can set the number of rings answering machine waits before answering. Three options to set: 3 rings, 5 rings, or Toll Saver. The default is 5 rings. To set the number of rings: 1. Press MENU button (refer to MENU – 04 RING SELECT) 2. Scroll UP or DOWN button to select: 04 RING SELECT. There are 3 rings (#01), 5 rings (#02), and Toll Saver (#03). 3.
Place Call by CID on Base Unit: 1. Under Standby mode, press CID button, the screen shows “ NEW CALL # TOTAL CALL# “, for example “ 01 16 “, means 1 new call, and total 16 calls of caller ID. If user has reviewed the new call, then the display become to show “ 00 16 “. 2. press UP button, the screen shows the latest (the last) Caller ID number, keep pressing UP button again, it shows the next latest Caller ID number.
seconds (long key). 5. the phone emit out beep sound and display showing “ SAVE TO M# “ after beep sound. 6. label the memory key. To save number from Caller ID records: 1. Under the standby mode on base, press CID button, 2. scroll UP or DOWN button to find the wanted Caller ID record, 3. press and hold down the memory key for a few seconds (long key) to save it. 4. the phone emit out sound and display shows “ SAVE TO M3 “.
6. Base hang up. 7. To end conversation, press EXIT button. Making call transfer from handset extension to base Call transfer from handset extension to base: 1. When outside call is ringing in, to lift handset from charger to answer the call (or press any key to answer if handset isn’t stayed at charger ), the handset screen shows “ CONF HOLD “ 2. Select HOLD by pressing Right softkey on handset, screen shows “ NO: RETRV “ 3.
second line), and go back to the first line and continue the conversation. While the first line caller is putting on hold, the caller will hear bi-bi(hold tone) tone until the line resumed. Making line swap To make line swap: 1. When conversation in the line (under the talking mode) on base (or handset, refer to Handset line swap), and another line come in. You do not hear the other line ringing while you are in the first line, but the LINE 2 LED is lighting on.
Handset is under conversation with outside line and invite base to join conference call. 1. when handset is on the line, the screen shows “ CONF HOLD “, 2. Select CONF from handset screen by pressing Left Shift key (soft key) on handset 3. screen shows “ DIAL INTER “. 4. Select INTER by pressing Right softkey on right side, 5. Handset then press “ *” star button (to call base), handset screen show “ NO:BS ”, 6. handset press OK, Base will keep ringing two-tone sound and display showing “ HS CALLING “ 7.
This phone system automatically displays incoming callers name and telephone numbers together with time and date of the call. It records up to 90 groups of call data. Base and handsets share the same caller ID data, no matter how many HANDSETS link to the same BASE unit. Each handset can select & pick up the caller ID records he want and save into his individual handset phonebook. The caller ID records are still in system memory after the handset has saved the record into his phonebook.
1. Under Standby mode, base press CID button, the screen shows NEW # TOTAL # 2. Select the wanted phone number & name by scroll UP or DOWN button, 3. press HOLD button to clean the caller ID record. 5. Press EXIT button to exit. To delete all caller ID: If you want to delete ALL Caller ID records at one time, Under any caller ID record display, 1. press and hold down HOLD button (long key) until the screen displaying “ Delete All CID ? “, 2. press OK button to delete all caller ID records, 3.
ADVANCE FEATURE on Base MENU The phone base allows system manager to set up or change the system defaults for customizing reasons. The system management function are as the Base Menu tree ( Handset isn’t allow you to access into Base Menu program). Base Menu contents To access base Menu: 1. Press MENU button on base, 2. Scroll UP or DOWN button to get the wanted function item.
3. to select the wanted language by using UP or DOWN button, press OK to save it. 4. press OK again to confirm. A three-beep sound emit out to confirm the setting. 01 Time/Date System will synchronize time and date to Answering Machine when answering machine is initiated. When incoming call with caller ID data, the time/date of Caller ID will update the phone system time/date automatically. To set time/date: Under Standby mode 1. press MENU button, 2.
03 RING SELECT To choose the number of times the phone rings before the Answering System responds, set the Ring Select switch to 3R, 5R or Toll SAVER. Set to 3R - System answers call after the third ring. Set to 5R - System answers call after the fifth ring. Set to Toll Saver - when you will be checking your system for message from a remote location using long distance services or from a pay phone. To set ringing selection: Under Standby mode 1. press MENU button, 2.
Setting Screen Call The Answering System allows you to listen to a caller leaving an ICM. To set the screen ON is to disable the base answering machine speakerphone sound while the caller is leaving message. The screen OFF is to resume the answering machine speakerphone sound while the caller is leaving message. To set screen call: Under Standby mode 1. press MENU button, 2. use UP or DOWN to select 06 SCREEN CALL, press OK button 3.
Note: To access mailbox in base, under standby mode, dial “ 0 “ to get General Box, then press PLAY button to listen ICM.
Local Area) and OUT OF AREA (1 group of Out of Area). Home Area and Local Area Code need to be programmed for caller ID dialing back. The Home area code is the same area code as the line connected to this base unit. The system allow user to input and save Home Area Code , or 7 groups of Local Area Codes, or Out of Area Code. The Local area codes are provided for areas with 10-digits dialing where multiple area codes are used to serve the calling area. To input area code: Under Standby mode 1.
To set call timer: Under Standby mode 1. press MENU button, 2. use UP or DOWN to select 09 CALL TIMER, press OK button 3. use UP or DOWN button to select 01 TIMER ON or 02 TIMER OFF, press OK to save it. 4. A three-beep sound emit out to confirm the setting. 5. When the call is over, hang up the phone, the timer stops counting. 10 L1:T/P To set up tone/pulse on L1: Under Standby mode 1. press MENU button, 2. use UP or DOWN to select 10 L1: T/P , press OK button 3.
2. use UP or DOWN to select 13 HOLD TONE , press OK button 3. there are 2 selection, scroll UP or DOWN button to select from 01 TONE ON, 02 TONE OFF, press OK to save it. 4. A three-beep sound emit out to confirm the setting. 5. the factory defaults as Tone ON. 14 FLASH TIME To set flash time: Under Standby mode 1. press MENU button, 2. use UP or DOWN to select 14 FLASH TIME , press OK button 3.
to be registered into base again. All the settings on the phone with ID changed still remain as same as ID before. To reset system ID: Under Standby mode 1. press MENU button, 2. use UP or DOWN to select 17 RESET ID , press OK button 3. the LCD display showing “ ARE YOU SURE? “, 4. A three-beep sound emit out to confirm the setting. 5. the screen does not show ID number , but the system has already changed ID number automatically (user doesn’t have to know the system ID code).
Setting Day/Time Stamp Once the phone is connected and set up the Day/Time, the system will synchronize the Answering Machine Day/Time. To enter into answering machine mode: 1. The phone system defaults as Memory mode (the LED on ANS./MEMORY button is light off when connecting the phone). You have to press ANS./MEMORY button to initiate Answering Machine (the LED lighting on indicates Answering Mode; LED light off indicates Memory mode). 2. You can close Answering Machine by pressing ANS.OFF button.
operation) 2. To access mailbox at remote telephone, you follow the voice instruction (refer to Answering machine operation via remote Tone Telephone) Recording Outgoing Greeting Your Answering System provides voice mail which can receive the incoming messages (ICM). Before using your Answering Machine, it is suggested that you record an Outgoing Message (OGM). This is the announcement callers will hear when the system answers a call.
Setting Announce Mode Setting Announce mode is your system answers incoming calls with your recorded greeting/memo, but not to record any incoming messages. To set Announce Mode: 1. Press MENU button on base, 2. Scroll UP or DOWN to find 02 ANNOUNCE, or just key in 02 from keypad. 3. use UP and DOWN to select 01 ANNOC ON , or 02 ANNOC OFF 4. press OK to save it. 5. Press OK again to confirm it. The system emit out three beep sound to confirm the setting.
3. After playing all of your messages, the system saves messages automatically. After playing all of your messages, the system announces “ end of message ”. To stop message: 1. Press STOP button once while playing a message, the system to pause the playing message. 2. Press PLAY button to continue playing the message where you stopped. 3. To press STOP button again (twice), the message is stopped. The system emit out “end of message”. To speed playing message/memo: 1.
Remote Operation through a remote access code at Tone Telephone You can use many Answering system features when you are away from home. i.e., you can remotely operate answering machine function like to record Outgoing OGM greeting, to get message, and to administer Outgoing message. To protect your privacy, most of the features can be used only after you enter the 3-digits remote access code. It’s a password to access messages from remote side. Remote Answering Machine operation 1.
messages “ or “ you have no message “. Pause 2 seconds, then continue to announce “ to record messages, please press 1; to get messages, please press 2; to administer outgoing greeting, please press 3 “. 2. If a command is not received by the system within 20 seconds, it will signal 3 beeps and hang up. 3. You follow the instruction codes to keep going the necessary steps. Recording Message remotely To record messages remotely: 1. When you get into remote control function, you press 1 to record message. 2.
*D”. After one message played, the system announces “ end of message. To repeat message, press 1; to save or continue, press #, to delete, press *D “. 4-1 To repeat message playing Selecting to repeat message by pressing 1, the system play the message again. 4-2 To save or continue message Selecting to save or continue message by pressing #, the system announces “ message saved, next message. “ Then the system continue to play the next message as step 4.
always on Greeting OFF (General Mailbox has to be left message).
Handset Operation Handset Registration To register new handset to base: 1. Under the Stand by mode, handset press Right softkey , 2. Scroll UP or DOWN button to find “ 02 REG.HANDSET”, or just dial 02 from keypad to go directly to item 2: “ 02 REG.HANDSET”“. Press OK button, 3. the screen shows “ HS NO: “, require to input wanted handset number by 2-digits, for instances, 00 - 99, dial 2-digit number, press OK button to confirm the handset number. 4.
Note: STANDBY Mode - When in STANDBY mode (ON-HOOK), the phone is capable of receiving a call. When the HANDSET is on the CORDLESS BASE UNIT, it is automatically in the STANDBY mode (ONHOOK). When the HANDSET is taken off the BASE UNIT, it remains in the STANDBY mode until you activate the LINE 1 or LINE 2 button When phone is under Standby mode, the LCD display is showing the current time & date information by Hour/Minutes/Month/Day.
Putting a call on mute via handset If you want to temporarily disable the microphone. To mute a call: 1. Press LINE 1 (or LINE 2) button to get the line, 2. to turn off the microphone off, press DEL/MUTE button. You can hear your caller but your caller can not hear you. 3. to speak to your caller, press DEL/MUTE again to resume microphone. 4. When the call is over, press EXIT button.
Tone. Use Right-Shift and Left-Shift buttons to adjust the ringer volume. Press Right Shift for higher volume; press Left Shift for low volume until it turn off the ringer. There are 8 levels of volume selection. To set the ring tone and volume: 1. Select MENU function by pressing Right Shift button 2. Scroll UP or DOWN button to select: 4 RING TONE, the tone option is from 01 – 05 (for base, refer to MENU – 08 RING TONE ), press OK button 3.
reviewed the new call, then the display become to show “ 00 16 “. 2. press UP button, the screen shows the latest (the last) Caller ID number, keep pressing UP button again, it shows the next latest Caller ID number. Keep pressing UP button to review the rest of caller ID records until to display “ END OF LIST ”, then to start to show the latest caller ID record again. number) (press DOWN button, the screen shows the first caller ID 3. Select the phone number & name by scroll UP or DOWN button, 4.
CALL TRANSFER When Handset (or base) is in conversation with outside line, you can transfer the call from handset to another handset. ( Handset use two soft keys under LCD screen : Right button and Left button to operate Call transfer function) Making call transfer from base to handset extension Call transfer from base to handset extension: 1. Base is under the line, press TRANSFER button, the display showing “ HS NO: “. 2. dial handset number, 3. press OK button again 4.
Note: if the second handset didn’t answer the transferred call within 30 seconds, the first handset will ring alarming user to get back the return call. Line SWAP When the first line is under talking mode, the second line is ringing and the signal of line is blinking too. To temporarily hold the conversation on the first line , and to get the second line, After finishing the second line conversation, get back to the first line and continue the conversation.
handphone) with outside line caller, 2. Base press HOLD CONF button, the screen shows “ TRANS: HS 3. Base dial Handset # (for example, 02), the handset-02 will ring, ”, 4. Handset-02 press OK button to get on hook with Base, 5. Base press CONF button to activate conference call among base, the outside caller in CO line, and handset-02. To make 3-way conference call among Handset, Base and outside line: Handset is under conversation with outside line and invite base to join conference call. 1.
“, 4. Handset select DIAL by pressing Left softkey, the screen shows “ TALK PBOOK “. 5. Handset select TALK by pressing Left softkey, The system get another C/O to connect with the third party. During in talking with line 2, the screen shows “ CONF RETRV “. 6. Handset select CONF by pressing Left softkey to activate the 3-way conference among line 1, line 2, and handset. Handset Broadcasting (to all handsets) 1.
2. press UP button to get the recent new caller data (or use DOWN button to get the first new caller data). To press UP or DOWN button once, the caller ID record is shown one record with sequence number. 3. User keep pressing UP button to the last record (the recent one) of caller ID, the next will display “ EMPTY RECORD # “, to remind user the last record with sequence number of record. User keep pressing DOWN button to the first caller ID record (with sequence number 01).
Call WAITING (Caller ID type II) When you subscribe to a Caller ID Call Waiting service from your local telephone company, this telephone will display the name and number of the second caller while you are on the conversation with your first caller. 1. When you having a conversation, this phone automatically display the name and number of the second caller. The name is blinking. 2. Press FLASH button to answer the second caller (in the same talking line). The first caller name and number will be displayed.
10 PHONEBOOK 01 Setting Languages: To change the language: Under Standby mode 5. press Right softkey to enter into handset menu, 6. use UP or DOWN to select 01 LANGUAGE, press OK button 7. use UP or DOWN button to select: 01-01 ENGLISH, 01-02 ESPANOL, 01-03 FRANCAIS. press OK to save it. 8. press OK again to confirm. A three-beep sound emit out to confirm the setting. 01 Handset Registration To register handset to base: 7. Under the Stand by mode, handset press Right softkey , 8.
blinking “ – “ at the end of name character. Use DEL to re-edit/correct the name. 4. Press OK button to save the name 4. A long-beep sound emit out to confirm the setting. 03 Setting Mailbox The phone system allows you with 5 mailboxes: one is for public mailbox (General Mailbox), and 4 personal Mailboxes. You can assign a mailbox to each of handset. A group of family members or colleagues might share the same Mailbox or has his own mailbox. Each Mailbox can be recorded with his own outgoing OGM greeting.
DOWN button. There are 8 levels available for choice. Move to the left side to turn off key beep volume (key beep level 1 is mute). 3. press OK again to confirm. A long-beep sound emit out to confirm the setting. 06 Setting Contrast To set contract: Under standby mode, press Right softkey. 1. Use UP or DOWN button to locate “ 07 SET CONTRAST “ ,press OK button. 2. the screen shows LCDCTL: 01 – 08, 4.
save it. 3. press OK again to confirm. A long-beep sound emit out to confirm the setting. To turn the display ON, is the phone display will show helpful hints automatically. To turn the display OFF, is the phone display doesn’t show helpful hints. This is for user who already know the operation. 09 SET Defaults To set defaults: Under Standby mode, 1. use Right softkey to select “ 10 SET DEFAULT? “, press OK button. 2. the system asking user by the display “ Are You Sure? “ 3. Press OK to save it. 4.
To add new phonebook Under standby mode, 1. press Right softkey to select “ 10 Phonebook “. 2. press OK button and screen displays the first stored phone number if user has saved phone book number before. 3. Press DOWN button to go to the next phone book number. If the next phone book is empty, the screen display “EMPTY REC # “. 5. press OK button, the screen shows “ ADD NUMBER?” 6. press OK button again, the screen is ready to input phone number 7. dial phone number, press OK button 8.
Machine function via handset or call to this phone system remotely, he has to dial password to enter into Answering Machine . The system will emit out announcement of instruction to guide user to follow the procedures. To initiate Answering Machine via handset: 1. Handset hold MENU button for 3 seconds to enter into Answering Mode. 2. Handset LCD display shows connecting…, then handset announces “ connecting to mailbox “.
handset to proceed above function. To operate remote control function: 4. When you get into remote control function, the system announces “You have # of new messages “ or “ you have no message “. Pause 2 seconds, then continue to announce “ to record messages, please press 1; to get messages, please press 2; to administer outgoing greeting, please press 3 “. 5. If a command is not received by the system within 45 seconds, it will signal 3 beeps and hang up. 6.
1. When you get into remote control function, you press 2 to get messages. 3. the system announces “ you have # of new messages “ or “ you have no new message”. 4. If you have new messages. The system announces “ message 1, sent at Sep 27, 11: 15 AM”, then to play announcement “ to listen message please press 0, to save or continue press #, to delete, press *D”. After one message played, the system announces “ end of message. To repeat message, press 1; to save or continue, press #, to delete, press *D “.
Note: Greeting ON means the mailbox doesn’t allow caller to leave message. Each mailbox can be setting to Greeting ON or Greeting OFF except General Mailbox. General Mailbox is always on Greeting OFF (General Mailbox has to be left message).
FCC Regulations: zThis device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. zThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
4RF Exposure Information (SAR) This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.
