Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date Description 1.0 October 8, 2009 • Revision A1 with firmware version 1.0 1.1 March 24, 2010 • Updated with minor changes 2.
Table of Contents Table of Contents Preface................................................................................. 2 Manual Revisions........................................................................... 2 Trademarks...................................................................................... 2 Product Overview............................................................... 5 Package Contents..........................................................................
Table of Contents Statistics..................................................................................49 IPv6...........................................................................................50 Help..................................................................................................51 Wireless Security..............................................................74 What is WPA?.................................................................................
Section 1 - Product Overview Product Overview Package Contents D-Link DAP-1522 Xtreme N® Duo Wireless Bridge/AP Ethernet Cable Power Adapter CD-ROM with User Manual Note: Using a power supply with a different voltage than the one included with the DAP-1522 will cause damage and void the warranty for this product. System Requirements • Computers with Windows®, Macintosh®, or Linux-based operating systems with an installed Ethernet adapter • Internet Explorer Version 6.0 or higher, Firefox 3.
Section 1 - Product Overview TOTAL PERFORMANCE Introduction Combines award winning access point features and 802.11n wireless technology to provide the best wireless performance. TOTAL SECURITY The most complete set of security features including WPA2 and MAC Address Control to protect your network against outside intruders. TOTAL COVERAGE Provides greater wireless signal rates even at farther distances for best-in-class Whole Home Coverage.
Section 1 - Product Overview Features • Faster Wireless Networking - The DAP-1522 provides up to 300Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. The performance of this 802.11n wireless access point gives you the freedom of wireless networking at speeds 13x faster than 802.11g. • Compatible with 802.11a and 802.
Section 1 - Product Overview Hardware Overview Connections 1 2 3 4 1 LAN Ports (1-4) 2 Mode Switch Three-way switch used to select AP 2.4GHz, AP 5GHz or Bridge mode. 3 Reset Button Pressing the Reset button restores the access point/bridge to its original factory default settings. 4 Power Receptor D-Link DAP-1522 User Manual Connect 10/100/1000 Ethernet devices such as computers, switches, and hubs. Receptor for the supplied power adapter.
Section 1 - Product Overview LEDs 1 1 Power LED 2 AP LED 3 Bridge LED 4 WPS LED 2 3 A solid blue light indicates a proper connection to the power supply. A solid light indicates that the DAP-1522 is in AP mode. A solid light indicates that the DAP-1522 is in bridge mode. A solid light indicates a successful WPS connection. A blinking light indicates the device is trying to establish a connection.
Section 2 - Installation Installation This section will walk you through the installation process. Placement of the DAP-1522 is very important. Do not place the DAP-1522 in an enclosed area such as a closet, cabinet, or in the attic or garage.
Section 2 - Installation Wireless Installation Considerations The D-Link wireless access point lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Section 2 - Installation AP/Bridge Mode Depending on how you want to use your DAP-1522 will determine which mode you use. This section will help you figure out which setting works with your setup. WIRELESS DIR-615 DAP-1522 AP Mode If you already have a wired or wireless router, and want to add an access point to connect your wireless clients to your network, you will need to move the switch on the back panel of the DAP-1522 to “AP2.4GHz” (for 2.4GHz) or “AP 5GHz” (for 5GHz).
Section 2 - Installation Create a Full MediaBand (5GHz wireless) Network If you have two DAP-1522 devices and want to create a wireless network with full MediaBand technology you will need to connect one Wireless Bridge to your router and move the switch on the back panel to “AP 5GHz”. The second Wireless Bridge will need to be placed next to your Ethernet-enabled devices and you will need to move the switch on the back panel to “Bridge”.
Section 2 - Installation One Touch AP Configuration This feature makes the Wireless Access Point to have the ability to exchange/learn the Wireless Profile from another Wireless Router/Access Point. 1. Press the WPS button on your Router or Access Point. WPS LED will flash on and off. 2. Press WPS Push Button on the DAP-1522 and hold it for 5 seconds. 3. When One click AP setup is complete, your DAP-1522 will have the same Wireless settings as your existing Router or AP.
Section 3 - Configuration Configuration for AP Mode This section will show you how to configure your new D-Link wireless access point using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web browser such as Internet Explorer and enter http://dlinkap or http://192.168.0.50 in the address field. Enter Admin for the user name and then enter your password. Leave the password blank by default.
Section 3 - Configuration Setup Wizard Click Launch Wireless Setup Wizard to quickly configure your access point. If you want to enter your settings without running the wizard, click Wireless Settings (on the left side) and skip to page 21.
Section 3 - Configuration Wireless Setup Wizard This Wizard is designed to assist you in connecting your wireless device to your access point. It will guide you through stepby-step instructions on how to get your wireless device connected. Click Next to continue. Select WPS as the configuration method only if your wireless device supports Wi-Fi Protected Setup. Skip to page 19 for Manual configuration. Click Next to continue.
Section 3 - Configuration Click Connect to continue. Click Next to continue. Click End to complete the setup.
Section 3 - Configuration Select Manual as the configuration method to set up your network manually. Click Next to continue. Enter a network name (SSID) and uncheck Assign a network key to automatically create a network key. To Manually assign a network key, check Assign a network key and enter a key in the box. Click Next to continue. Click Save to save your network settings.
Section 3 - Configuration Manual Configuration Wireless Settings Wireless Band: Displays either 2.4GHz or 5.0GHz. Enable Wireless: Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Wireless When you are browsing for available wireless networks, Network Name: this is the name that will appear in the list (unless Visibility Status is set to Invisible, see below). This name is also referred to as the SSID.
Section 3 - Configuration Enable Auto Channel The Auto Channel Scan setting can be selected to allow the DAP-1522 to choose the channel with the least amount of interference. Scan: Wireless Channel: Indicates the channel setting for the DAP-1522. The Channel can be changed to fit the channel setting for an existing wireless network or to customize the wireless network. If you enable Auto Channel Scan, this option will be grayed out.
Section 3 - Configuration LAN Settings Dynamic IP This section will allow you to change the local network settings of the access point and to configure the DHCP settings. Device Name: Enter the Device Name of the AP. It is recommended to change the Device Name if there is more than one D-Link device within the subnet. LAN Connection Use the drop-down menu to select Dynamic IP Type: (DHCP) to automatically obtain an IP address on the LAN/private network.
Section 3 - Configuration Static IP Device Name: Enter the Device Name of the AP. It is recommended to change the Device Name if there is more than one D-Link device within the subnet. IPv4 Connection Use the drop-down menu to select Static IP. Type: Access Point IP Enter the IP address of the access point. The default Address: IP address is http://192.168.0.50.
Section 3 - Configuration LAN Setup Static IPv6 IPv6 Address: Enter the static IPv6 address provided by your Internet Service Provider. Subnet Prefix Enter the IPv6 subnet prefix length. Length: Default Gateway: Enter the default gateway IP address. Primary DNS Enter the primary DNS server IP address. Server: Secondary DNS Enter the secondary DNS server IP address.
Section 3 - Configuration LAN Setup IPv6 - Auto-Configuration Obtain IPv6 Select to obtain IPv6 DNS Servers automatically. DNS Servers automatically: Use the following Enter a specific DNS server address. IPv6 DNS Servers: Primary DNS Server: Enter the primary DNS server IP address. Secondary DNS Enter the secondary DNS server IP address.
Section 3 - Configuration Advanced MAC Address Filter The MAC address filter section can be used to filter network access by machines based on the unique MAC addresses of their network adapter(s). It is most useful to prevent unauthorized wireless devices from connecting to your network. A MAC address is a unique ID assigned by the manufacturer of the network adapter. Configure When Turn MAC Filtering OFF is selected, MAC addresses MAC Filtering: are not used to control network access.
Section 3 - Configuration Advanced Wireless Transmit Power: Sets the transmit power of the antennas. WMM Enable: WMM is QoS for your wireless network. This will improve the quality of video and voice applications for your wireless clients. Short GI: Check this box to reduce the guard interval time therefore increasing the data capacity. However, it is less reliable and may create higher data loss. IGMP Snooping: This enables IGMP snooping for the wireless connection.
Section 3 - Configuration Guest Zone The Guest Zone feature will allow you to create temporary zones that can be used by guests to access the Internet. These zones will be separate from your main wireless network. Enable Guest Check to enable the Guest Zone feature. Select Zone: the schedule of time when the Guest Zone will be active. The schedule may be set to Always, which will allow the particular service to always be enabled. You can create your own times in the Maintenance > Schedules section.
Section 3 - Configuration DHCP Server DHCP stands for Dynamic Host Control Protocol. The DAP-1522 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DAP-1522.
Section 3 - Configuration DHCP Reservation If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The access point will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range. Enable: Check this box to enable the reservation. Computer Name: Enter the computer name or select from the drop-down menu. IP Address: Enter the IP address you want to assign to the computer or device.
Section 3 - Configuration WLAN Partition WLAN Partition allows you to segment your Wireless network by managing access to both the internal station and Ethernet access to your WLAN. Internal Station Use the drop-down menu to either Allow or Deny Connection: internal station connection. Ethernet to Use the drop-down menu to either Allow or Deny WLAN Access: Ethernet to Wireless LAN access.
Section 3 - Configuration QoS The Quality of Service (QoS) feature regulates the flow of data through the access point by assigning a priority to each packet. It enhances your experience of wireless network usage by prioritizing the traffic of different applications. Enabling this option allows the AP to prioritize traffic. There are two options available for the special application. Enable QoS: Enable this option if you want QoS to prioritize your traffic.
Section 3 - Configuration Priority by Users can set the priority and percentage of total Protocol: bandwidth reserved for each of their four traffic categories. Please note that the combined percentage value of transmission limits does not have to be 100%. These percentages represent the maximum bandwidth designated for each traffic category. Ethernet The value entered here indicates the Ethernet to Wireless: wireless speed required before the Advanced QoS function is enabled.
Section 3 - Configuration User Defined Defines the priority level for your device. Priority: Other Traffic Other traffic generated that does not regard the aforementioned packet delivery. Priority: Note: Normally the wireless connection transmits application data packets based on the wireless to Ethernet speed and Ethernet to wireless speed. Users can treat the two speeds as system transmission bandwidth, where all applications will share the whole system bandwidth based on assigned priorities.
Section 3 - Configuration Traffic Manager Traffic Manager assigns the device’s entire bandwidth, which includes both the wireless to Ethernet speed and Ethernet to wireless speed. The user may add rules for data transmission performance between the access point device and the individual client. For unlisted client traffic, users can either choose to deny or forward packet transferred for such clients.
Section 3 - Configuration Add Traffic Manager Rule In Traffic Manager Rule enter settings for each user of your network, using adequate IP (Client IP) or MAC address (Client MAC). Set appropriate Ethernet to Wireless and Wireless to Ethernet speeds for the traffic you want to regulate. Name: Enter a name for your new rule. Client IP (optional): The IP address assigned to the client.
Section 3 - Configuration Wi-Fi Protected Setup This feature allows you to add devices to your network using a PIN or button Press. Your devices must support Wi-Fi Protected Setup in order to be configured by this method. Enable: Select to Enable this feature and add devices to your network. Lock Wireless Select to Enable this feature and Lock Wireless Security Security Settings.
Section 3 - Configuration User Limit The User Limit section allows you to set a maximum number of wireless clients that can connect to the access point. Enable User Limit: Check the box to enable. User Limit (1-32): Enter the maximum number of clients allowed to connect to the access point.
Section 3 - Configuration Maintenance Admin This page will allow you to change the Administrator password. The administrator password has read/write access. Password: Enter a new password for the Administrator Login Name. The administrator can make changes to the settings. Verify Enter the same password that you entered in the Password: previous text box in order to confirm its accuracy.
Section 3 - Configuration Time The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in. Daylight Saving can also be configured to automatically adjust the time when needed. Time Zone: Select your Time Zone from the drop-down menu. Daylight To select Daylight Saving time manually, click the Saving: Enable Daylight Saving check box. Enable NTP NTP is short for Network Time Protocol.
Section 3 - Configuration System Save to Local Use this option to save the current access point Hard Drive: configuration settings to a file on the hard disk of the computer you are using. First, click the Save button. You will then see a file dialog, where you can select a location and file name for the settings. Load from Local Use this option to load previously saved access point Hard Drive: configuration settings. First, click Browse to find a previously save file of configuration settings.
Section 3 - Configuration Firmware You can upgrade the firmware of the access point here. Make sure the firmware you want to use is on the local hard drive of the computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support website for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from this site.
Section 3 - Configuration If you load a language pack and would like to go back to English, click Maintenance > System and click on Clear next to Clear Language Pack.
Section 3 - Configuration System Check This section Ping Tests by sending ping packets to test if a computer on the internet is running and responding. Ping Test / The Ping Test / IPv6 Ping Test is used to send Ping IPv6 Ping Test: packets to test if a computer is on the Internet. Enter the host name or IP/IPv6 address that you wish to Ping, and click Ping. Ping Result: The results of your ping attempts will be displayed here.
Section 3 - Configuration Schedule Name: Enter a name for your new schedule. Days: Select a day, a range of days, or All Week to include every day. Time: Enter a start and end time for your schedule. Schedule Rules The list of schedules will be listed here. Click the List: Edit icon to make changes or click the Delete icon to remove the schedule.
Section 3 - Configuration Status Device Info This page displays the current information for the DAP-1522. It will display the LAN and wireless LAN information. General: Displays the access point’s time and firmware version. LAN: Displays the MAC address and the private (local) IP settings for the access point. Wireless LAN: Displays the wireless MAC address and your wireless settings such as SSID and Channel.
Section 3 - Configuration Wireless The wireless section allows you to view the wireless clients that are connected to your wireless access point. SSID: Displays the name of your network. MAC Address: The Ethernet ID (MAC address) of the wireless client. UpTime: Displays the amount of time the wireless client has been connected to the access point. Mode: The transmission standard being used by the client. Values are 11a, 11b, 11g, 11ng or 11na for 802.11a, 802.11b, 802.11g or 802.11n respectively.
Section 3 - Configuration Logs The access point automatically logs (records) events of possible interest in its internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted, but logs of the latest events are retained. The Logs option allows you to view the access point logs. Log Type: There are two types of logs that can be viewed: System Activity, Debug System, Attacks, Dropped Packets and Notice. First Page: Click to view the first page.
Section 3 - Configuration Statistics The Statistics page displays all of the LAN and Wireless packets transmit and receive statistics. TX Packets: The total number of packets sent from the access point. RX Packets: The total number of packets received by the access point. TX Packets Displays the number of packets that were dropped Dropped: while sending, due to errors, collisions, or access point resource limitations.
Section 3 - Configuration IPv6 This page will display all your network connection details. IPv6 Connection Type: Displays IPv6 connection mode. LAN IPv6 Address: Displays LAN IPv6 address. IPv6 Default Gateway: Displays the IPv6 address of the default gateway. LAN IPv6 Link-Local Displays the LAN IPv6 link-local address. Address: Primary DNS Server: Displays the IPv6 address of the primary DNS server. Secondary DNS Server: Displays the IPv6 address of the secondary DNS server.
Section 3 - Configuration Help D-Link DAP-1522 User Manual 51
Section 3 - Configuration Configuration for Bridge Mode This section will show you how to configure your new D-Link wireless MediaBridge using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter dlinkap or enter 192.168.0.50 in the address field. Select Admin from the drop-down menu and then enter your password. Leave the password blank by default.
Section 3 - Configuration Setup Wizard This wizard is designed to assist you in configuring the wireless settings for your bridge. It will guide you through step-by-step instructions on how to setup your wireless network. Click Launch Wireless Setup Wizard Click Next to continue with the wizard setup.
Section 3 - Configuration Select WPS configuration if you want to use Wi-Fi Protected Setup. If you want to set up your network manually, skip to page 55. Click Next to continue. Click Connect to continue.
Section 3 - Configuration Press down the WPS Button on the wireless device you are adding to your network to complete the setup. Select Manual configuration to set up your network manually. Click Next to continue.
Section 3 - Configuration Enter the Wireless Network Name of the AP or click the Site Survey button to find the AP. Click Next to continue on to page 57.
Section 3 - Configuration If you clicked on Site Survey, the following screen will be displayed. Find your access point from the list and click Connect to complete the Setup Wizard. Choose which Security Mode you want to use and click Next to continue.
Section 3 - Configuration If you choose WEP, enter the wireless security password and click Next to complete the Setup Wizard. Select Auto (WPA or WPA2) and click Next to continue. Enter the WPA/WPA2 Personal Passphrase and click Next to establish wireless connection.
Section 3 - Configuration The following screen opens to indicate that you have successfully saved your new settings.
Section 3 - Configuration Wireless Site Survey: A function that looks for available wireless networks. Enable Wireless: Click the check box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Wireless Service Set Identifier (SSID) is the name of your wireless Network network. Create a name using up to 32 characters. The Name: SSID is case sensitive. Band Width: Select the Band Width: Auto 20/40 - Select if you are using both 802.
Section 3 - Configuration LAN Settings Static This section will allow you to change the local network settings of the bridge and to configure the Static settings. Device Name: Enter the Device Name of the AP and click Next to continue. It is recommended to change the Device Name if there is more than one D-Link device within the subnet. LAN Use the drop-down menu to select Static IP if your ISP Connection assigned you the IP address, subnet mask, gateway, Type: and DNS server addresses.
Section 3 - Configuration Dynamic LAN Connection Select DHCP to automatically obtain an IP address Type: on the LAN/private network.
Section 3 - Configuration Advanced Advanced Network Settings This section allows uses to change the LAN Settings. We do not recommend changing these settings from factory default.
Section 3 - Configuration Maintenance Admin This page will allow you to change the Administrator password. Admin has read/write access. Password: Enter a new password for the Administrator Login Name. The administrator can make changes to the settings. Verify Enter the same password that you entered in the Password: previous textbox in order to confirm its accuracy.
Section 3 - Configuration Time The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in. Daylight Saving can also be configured to automatically adjust the time when needed. Time Zone: Select the Time Zone from the drop-down menu. Enable Daylight To select Daylight Saving time manually, tick the Saving: Enable Daylight Saving check box.
Section 3 - Configuration System Save Settings To Local Use this option to save the current access point Hard Drive: configuration settings to a file on the hard disk of the computer you are using. First, click the Save button. You will then see a file dialog, where you can select a location and file name for the settings. Load From Local Hard Use this option to load previously saved access Drive: point configuration settings.
Section 3 - Configuration Firmware You can upgrade the firmware of the access point here. Make sure the firmware you want to use is on the local hard drive of the computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site.
Section 3 - Configuration If you load a language pack and would like to go back to English, click Maintenance > System and click on Clear next to Clear Language Pack.
Section 3 - Configuration Schedule Name: Enter a name for your new schedule. Days: Select a day, a range of days, or All Week to include every day. Time: Check All Days or enter a start and end time for your schedule. Wireless: Select On or Off from the drop-down menu. Add: Click Add to save your schedule. You must click Save Settings at the top for your schedules to go into effect. Schedule Rules The list of schedules will be listed here.
Section 3 - Configuration Status Device Info This page displays the current information for the DAP-1522. It will display the LAN and wireless LAN information. General: Displays the access point’s time and firmware version. LAN: Displays the MAC address and the private (local) IP settings for the access point. Wireless LAN: Displays the wireless MAC address and your wireless settings such as SSID and Channel.
Section 3 - Configuration Logs The access point automatically logs (records) events of possible interest in its internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted, but logs of the latest events are retained. The Logs option allows you to view the access point logs. You can define what types of events you want to view and the level of the events to view.
Section 3 - Configuration Statistics The Statistics page displays all of the LAN and Wireless packets transmit and receive statistics. TX Packets: The total number of packets sent from the access point. RX Packets: The total number of packets received by the access point. TX Packets Displays the number of packets that were dropped Dropped: while sending, due to errors, collisions, or access point resource limitations.
Section 3 - Configuration Help D-Link DAP-1522 User Manual 73
Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DAP-1522 offers the following types of security: • WPA2 (Wi-Fi Protected Access 2) • WPA (Wi-Fi Protected Access) • WPA2-PSK (Pre-Shared Key) • WPA-PSK (Pre-Shared Key) What is WPA? WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
Section 4 - Security Configure WPA/WPA2 It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the access point (192.168.0.50). Click on Setup and then click Wireless Settings on the left side. 2.
Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows® 7 It is recommended to enable wireless security (WPA/WPA2) on your access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). Wireless Icon 2. The utility will display any available wireless networks in your area.
Section 5 - Connecting to a Wireless Network 3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. 4. The following window appears while your computer tries to connect to the router.
Section 5 - Connecting to a Wireless Network 5. Enter the same security key or passphrase that is on your access point and click Connect. You can also connect by pushing the WPS button on the router. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows Vista® Windows Vista® users may use the convenient, built-in wireless utility. Follow these instructions: From the Start menu, go to Control Panel, and then click on Network and Sharing Center. The utility will display any available wireless networks in your area. Click on a network (displayed using the SSID) under Select a network to connect to and then click the Connect button.
Section 5 - Connecting to a Wireless Network Click Connect Anyway to continue. The utility will display the following window to indicate a connection is being made. The final window indicates the establishment of a successful connection. The next two pages display the windows used to connect to either a WEP or a WPA-PSK wireless network.
Section 5 - Connecting to a Wireless Network Configure Security It is recommended to enable wireless encryption on your wireless bridge or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key being used. Select a network to connect to and then click the Connect button. Enter the appropriate security key or passphrase in the field provided and then click the Connect button.
Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows® XP Windows XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows XP utility as seen below.
Section 5 - Connecting to a Wireless Network Configure Security It is recommended to enable wireless security on your wireless bridge or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key being used. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the security passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless access point.
Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DAP-1522. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples.) 1. Why can’t I access the web-based configuration utility? When entering the IP address of the D-Link access point (192.
Section 6 - Troubleshooting • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Appendix A - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office. D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford.
Appendix A - Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Appendix A - Wireless Basics Security Don’t let your next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the access point. Refer to product manual for detail information on how to set it up. Wireless Modes There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless bridge.
Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® 7 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center. Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. Windows® XP - Click on Start > Control Panel > Network Connections.
Appendix C - Technical Specifications Technical Specifications Modulation • 11b: DQPSK, DBPSK and CCK • 11a/g: BPSK, QPSK, 16QAM, 64QAM, OFDM • 11n: BPSK, QPSK, 16QAM, 64QAM, OFDM, MCS Standards • IEEE 802.11n • IEEE 802.11a • IEEE 802.11g • IEEE 802.3 • IEEE 802.3u Frequency Range2 • 2.4GHz to 2.483GHz • 5.15GHz~5.
Appendix D - Contacting Technical Support Contacting Technical Support U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. Before you contact technical support, please have the following ready: • Model number of the product (e.g. DAP-1522) • Hardware Revision (located on the label on the bottom of the access point (e.g. rev A1)) • Serial Number (s/n number located on the label on the bottom of the access point).
Appendix E - Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Appendix E - Warranty Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation.
Appendix E - Warranty • After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. DLink will only replace the defective portion of the product and will not ship back any accessories.
Appendix E - Warranty Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS T
Appendix E - Warranty Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix E - Warranty Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device This device has been designed to operate with an antenna having a maximum gain of 2dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada.
Appendix F - Registration Registration Register your product online at registration.dlink.com Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 2.
