Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Table of Contents Preface.............................................................................i Trademarks....................................................................................................... i Product Overview................................................................ 1 Package Contents............................................................................................ 1 System Requirements...............................................................................
Networking Basics....................................................................................... 105 Connect to a Wireless Network.................................................................... 107 Using Window 7................................................................................. 107 Using Window 7 and WPS.................................................................. 109 Using Window Vista............................................................................
Section 1 - Product Overview Product Overview Package Contents Check for the supplied accessories below: • Wireless 802.11b/g/n Dual Band Router • Power Adapter with extra Power Cable • Ethernet Cable • CD-ROM (with installation software and manuals) • Quick Installation Guide • Stand • Mounting Kit Note: Using a power supply with a different voltage rating than the one included with the product, will cause damage and void the warranty for this product.
Section 1 - Product Overview About this Product This user’s guide provides a wonderful insight into the functionality of the product called the D-Link DIR-645 Wireless Internet Router. This guide is based on the current running firmware/software version available for this product and might touch on some new and exciting topics never seen on this product line before providing a rewarding reading experience and in the end acts as a guide when installing and maintaining this product.
Section 1 - Product Overview Hardware Overview Front Panel Internet Light A solid green light indicates that the Internet connection negotiation has successfully been completed. WPS Light and Button Press the WPS button for 1 second to initiate the WPS process. The button will flash green while a WPS connection is being established. The button will light green for 5 seconds if a successful WPS connection has been made.
Section 1 - Product Overview Back Panel USB Port The USB port can be used for WPS enabled Wireless USB adapters. Ethernet Ports The four LAN ports can be used for 10/100/1000Mbps LAN connections. Internet Port The Internet (WAN) port can be used for connections like a DSL/Cable modem. D-Link DIR-645 User Manual Power Receptor Receptor for the supplied power adapter.
Section 1 - Product Overview Bottom Panel Reset Button Press the button to restore the device to its original factory default settings.
Section 2 - Hardware Installation Hardware Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, attic or garage. Before You Begin • The router is designed for use with the Ethernet port on your broadband modem. If you were using the USB connection before using the router, you must turn off your modem and disconnect the USB cable.
Section 2 - Hardware Installation Connect to Cable/DSL/Satellite Modem If you are connecting the router to a Cable/DSL/Satellite Modem, please follow the steps below: 1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Turn the power off on your modem. If there is no on/off switch, unplug the modem’s power adapter. Shut down your computer. 3.
Section 3 - Software Configuration Software Configuration This section will guide you through how to configure and use your D-Link wireless router using the Web graphical user interface.. Connect to the Web User Interface To access the configuration utility, open a web-browser application such as Internet Explorer and enter the IP address of the router in the address bar and click on Go. Note: The default IP address for the router is 192.168.0.
Section 3 - Software Configuration Setup Category In the Setup Category users will be able to configure features that are essential to the functionality of this router. The pages found in the Setup Category are: Internet: On the Internet page, users can configure the method this router uses to connect to the Internet. There are two types of configuration methods to choose from, the Internet Connection Setup Wizard and the Manual Internet Connection Setup.
Section 3 - Software Configuration Internet (Setup Wizard) When configuring the router for the first time, we recommend that you click use the Internet Connection Setup Wizard, and follow the instructions on the screen. This wizard is designed to assist user with a quick and easy method to configure the Internet Connectivity of this router. Anytime during the Internet Connection Setup Wizard, the user can click on the Cancel button to discard any changes made and return to the main Internet page.
Section 3 - Software Configuration Step 2: Select Your Time Zone Select the appropriate time zone for your location. This information is required to configure the time-based options for the router. Click Next to continue. Step 3: Internet Connection Here the user will be able to configure the Internet Connectivity used by this device. If your ISP connection is listed in the drop-down menu select it and click Next.
Section 3 - Software Configuration Step 3: Internet Connection (Dynamic IP Address) After selecting the Dynamic IP Address Internet connection method, the following page will appear. The following parameters will be available for configuration: MAC Address: Enter the MAC address of the Internet gateway (plugged into the Internet port of this device) here.
Section 3 - Software Configuration Step 3: Internet Connection (PPPoE) After selecting the PPPoE Internet connection method, the following page will appear: The following parameters will be available for configuration: Address Mode: Here the user can specify whether this Internet connection requires the use of a Dynamic or Static IP address. PPPoE usually requires a Dynamic IP configuration. IP Address: Enter the PPPoE IP address used here. This option is only available if Static IP is selected.
Section 3 - Software Configuration Step 3: Internet Connection (PPTP) After selecting the PPTP Internet connection method, the following page will appear: The following parameters will be available for configuration: Address Mode: Here the user can specify whether this Internet connection requires the use of a Dynamic or Static IP address. PPTP usual requires a Dynamic IP configuration. PPTP IP Address: Enter the PPTP IP address used here. This option is only available if Static IP is selected.
Section 3 - Software Configuration Step 3: Internet Connection (L2TP) After selecting the L2TP Internet connection method, the following page will appear: The following parameters will be available for configuration: Address Mode: Here the user can specify whether this Internet connection requires the use of a Dynamic or Static IP address. L2TP usual requires a Dynamic IP configuration. L2TP IP Address: Enter the L2TP IP address used here. This option is only available if Static IP is selected.
Section 3 - Software Configuration Step 3: Internet Connection (Static IP Address) After selecting the Static IP Address Internet connection method, the following page will appear: The following parameters will be available for configuration: IP Address: Enter the Static IP address provided by the ISP here. Subnet Mask: Enter the Subnet Mask provided by the ISP here. Gateway Address: Enter the Gateway IP address provided by the ISP here. Primary DNS Enter the Primary DNS IP address used here.
Section 3 - Software Configuration Internet (Manual) On this page the user can configure the Internet Connection settings manually. To access the Manual Internet Connection Setup page, click on the Manual Internet Connection Setup button. On this page there a multiple parameters that can be configured regarding the Internet Connection setup. We’ll discuss them from top to bottom. At any given point the user can save the configuration done, on this page, by clicking on the Save Settings button.
Section 3 - Software Configuration Secondary DNS: Enter the Secondary DNS IP address used here. This field is normally optional. Only one DNS address is required for a functional Internet connection, but using a second DNS address provides more stability. MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1500 is the default MTU.
Section 3 - Software Configuration My Internet Connection is: PPPoE (Username/Password) Another Internet Connection type is PPPoE. This option is typically used if you have a DSL Internet Connection. Make sure to remove the PPPoE software installed on your computer first before using this connection type. Most of the information needed for this connection type is provided to you by your ISP.
Section 3 - Software Configuration Secondary DNS Server: MTU: MAC Address: Enter the Secondary DNS IP address used here. This field is normally optional. Only one DNS address is required for a functional Internet connection, but using a second DNS address provides more stability. Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1492 is the default MTU.
Section 3 - Software Configuration has been defined in the Schedules page. To create a new schedule, click the New Schedule button to open the Schedules page. Schedules will be discussed later. Maximum Idle Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature, enable Auto-reconnect. Time: Primary DNS Enter the Primary DNS IP address used here. Server: Secondary DNS Enter the Secondary DNS IP address used here.
Section 3 - Software Configuration After selecting L2TP, the following parameters will be available for configuration: Address Mode: Here the user can specify whether this Internet connection requires the use of a Dynamic or Static IP address. L2TP usual requires a Dynamic IP configuration. L2TP IP Address: Enter the L2TP IP address used here. This option is only available if Static IP is selected. L2TP Subnet Enter the L2TP Subnet Mask used here.
Section 3 - Software Configuration My Internet Connection is: DS-Lite) Another Internet Connection type is DS-Lite. After selecting DS-Lite, the following parameters will be available for configuration: DS-Lite Select the DS-Lite DHCPv6 Option to let the router Configuration: allocate the AFTR IPv6 address automatically. Select the Manual Configuration to enter the AFTR IPv6 address in manually.
Section 3 - Software Configuration Wireless Settings On this page the user can configure the Wireless settings for this device. There are 3 ways to configure Wireless using this router. Firstly, the user can choose to make use for the quick and easy Wireless Connection Setup Wizard. Secondly, the user can choose to make use Wi-Fi Protected Setup. Lastly, the user can configure the Wireless settings manually.
Section 3 - Software Configuration Step 2: This step will only be available if the user selected ‘Manually assign a network key’ in the previous step. Here the user can manually enter the WPA/WPA2 pre-shared key in the Wireless Security Password space provided. The key entered must be between 8 and 63 characters long. Remember, this key will be used when wireless clients wants to connect to this device. So please remember this key to prevent future troubleshooting.
Section 3 - Software Configuration Wireless Settings: Wi-Fi Protected Setup Wizard If your Wireless Clients support the WPS connection method, this Wi-Fi Protected Setup Wizard can be used to initiate a wireless connection between this device and Wireless clients with a simple click of the WPS button. The Wi-Fi Protected Setup Wizard is specially designed to assist basic network users with a simple, step-by-step set of instructions to connect wireless clients to this router using the WPS method.
Section 3 - Software Configuration Step 2: After selecting Manual, the following page will appear. On this page to user can view the wireless configuration of this router. The wireless clients should configure their wireless settings to be identical to the settings displayed on this page for a successful connection. This option is for wireless clients that can’t use the WPS method to connect to this device. Click on the Prev button to return to the previous page.
Section 3 - Software Configuration The following parameters will be available for configuration: Wireless Band: Displays the wireless band being configured. In this option we find that the following parameters will be regarding the 2.4GHz band. Enable Wireless: Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Select the time frame that you would like your wireless network enabled. The schedule may be set to Always.
Section 3 - Software Configuration By default the wireless security of this router will be disabled. In this next option the user can enabled or disable wireless security for the frequency band 2.4GHz. There are two types of encryption that can be used. WEP or WPA/WPA2. Wireless Security Mode: WEP Wired Equivalent Privacy (WEP) is the most basic form of encryption that can be used for wireless networks. Even though it is known as a ‘weak’ security method, it is better than no security at all.
Section 3 - Software Configuration Wireless Security Mode: WPA-Personal Wi-Fi Protected Access (WPA) is the most advanced and up to date wireless encryption method used today. This is the recommended wireless security option. WPA supports two authentication frameworks. Personal (PSK) and Enterprise (EAP). Personal requires only the use of a pass-phrase (Shared Secret) for security.
Section 3 - Software Configuration Wireless Security Mode: WPA-Personal Wi-Fi Protected Access (WPA) is the most advanced and up to date wireless encryption method used today. This is the recommended wireless security option. WPA supports two authentication frameworks. Personal (PSK) and Enterprise (EAP). Personal requires only the use of a pass-phrase (Shared Secret) for security.
Section 3 - Software Configuration Network Settings On this page the user can configure the internal network settings of the router and also able to configure the built-in DHCP server to assign IP addresses to computers on the network. The IP address that is configured here is the IP address that is used to access the Web-based management interface. If you change the IP address in this section, you may need to adjust your PC’s network settings to access the network again.
Section 3 - Software Configuration The following parameters will be available for configuration: Enable DHCP Check this box to enable the DHCP server on your router. Server: Uncheck to disable this function. DHCP IP Address Enter the starting and ending IP addresses for the DHCP Range: server’s IP assignment. DHCP Lease The length of time for the IP address lease. Enter the Lease Time: time in minutes.
Section 3 - Software Configuration Primary WINS Server IP address: Secondary WINS Server IP address: Configure the IP address of the preferred WINS server. WINS Servers store information regarding network hosts, allowing hosts to ‘register’ themselves as well as discover other available hosts, e.g. for use in Network Neighborhood. This setting has no effect if the ‘Learn NetBIOS information from WAN’ is activated. Configure the IP address of the backup WINS server, if any.
Section 3 - Software Configuration IPv6 On this page, the user can configure the IPv6 Connection type. There are two ways to set up the IPv6 Internet connection. You can use the Web-based IPv6 Internet Connection Setup Wizard, or you can manually configure the connection.
Section 3 - Software Configuration Step 1: Configure Your IPv6 Internet Connection There are several connection types to choose from. If you are unsure of your connection method, please contact your IPv6 Internet Service Provider. Note: If using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or disabled. The 3 options available on this page is IPv6 over PPPoE, Static IPv6 address and Route, and Tunneling Connection.
Section 3 - Software Configuration Set Static IPv6 Address Connection This mode is used when your ISP provides you with a set IPv6 addresses that does not change. The IPv6 information is manually entered in your IPv6 configuration settings. You must enter the IPv6 address, Subnet Prefix Length, Default Gateway, Primary DNS Server, and Secondary DNS Server. Your ISP provides you with all this information.
Section 3 - Software Configuration Tunneling Connection (6rd) After selecting the Tunneling Connection (6rd) option, the user can configure the IPv6 6rd connection settings. The following parameters will be available for configuration: 6rd IPv6 Prefix: Enter the 6rd IPv6 address and prefix value used here. IPv4 Address: Enter the IPv4 address used here. Mask Length: Enter the IPv4 mask length used here. Assigned IPv6 Displays the IPv6 assigned prefix value here.
Section 3 - Software Configuration Manual IPv6 Internet Connection Option For the advanced user that have configured a router before, click on the Manual IPv6 Internet Connection Setup button to input all the settings manually. On this page the user can manually configure the mode that the Router will use to access an IPv6 Internet connection. There are several connection types to choose from: Link-local, Static IPv6, DHCPv6, Stateless Auto-Configuration, PPPoE, IPv6 over IPv4 Tunnel and 6to4.
Section 3 - Software Configuration The following parameters will be available for configuration: Obtain IPv6 Select this option to obtain the DNS Server addresses DNS Server automatically. automatically: Use the following Select this option to manually enter the DNS Server IPv6 DNS addresses used. Servers: Primary DNS: Enter the primary DNS Server address used here. Secondary DNS: Enter the secondary DNS Server address used here. Use the section to configure the internal network settings of your router.
Section 3 - Software Configuration IPv6 Address This option is only available when the auto-configuration Range (Start): type is set to Stateful. Enter the start IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address This option is only available when the auto-configuration Range (End): type is set to Stateful. Enter the end IPv6 Address for the DHCPv6 range for your local computers. IPv6 Address This option is only available when the auto-configuration Lifetime: type is set to Stateful.
Section 3 - Software Configuration Primary DNS Enter the WAN primary DNS Server address used here. Server: Secondary DNS Enter the WAN secondary DNS Server address used here. Server: The following parameters will be available for configuration: LAN IPv6 Enter the LAN (local) IPv6 address for the router here. Address: LAN IPv6 Link- Displays the Router’s LAN Link-Local Address here.
Section 3 - Software Configuration IPv6 Connection Type: Autoconfiguration (SLAAC/DHCPv6) In the following section we’ll discuss the parameters that can be configured when setting up an Autoconfiguration (SLAAC/DHCPv6) connection. This is a method of connection where the ISP assigns your IPv6 address when your router requests one from the ISP’s server. Some ISP’s require you to make some settings on your side before your router can connect to the IPv6 Internet.
Section 3 - Software Configuration The following parameters will be available for configuration: Enable Automatic The user can tick this option to enable the auto-configuration IPv6 address: feature. Enable Automatic Tick this option to enable the automatic DHCP-PD on the DHCP-PD in LAN: LAN. Autoconfiguration The user can select the auto-configuration type used here. Type: Router This option is only available when the auto-configuration Advertisement type is set to Stateless.
Section 3 - Software Configuration IPv6 Connection Type: PPPoE Select this option if your ISP requires you to use a PPPoE (Point to Point Protocol over Ethernet) connection to IPv6 Internet. DSL providers typically use this option. This method of connection requires you to enter a Username and Password (provided by your Internet Service Provider) to gain access to the IPv6 Internet. The supported authentication protocols are PAP and CHAP.
Section 3 - Software Configuration The following parameters will be available for configuration: Enable DHCP-PD: Select this option to enable DHCP PD. LAN IPv6 Enter the LAN IPv6 address used here. This address must be Address: in the ‘/64’ subnet. LAN IPv6 Link- Displays the LAN IPv6 Link-Local address used here. Local Address: The following parameters will be available for configuration: Enable Automatic The user can tick this option to enable the auto-configuration IPv6 address: feature.
Section 3 - Software Configuration IPv6 Connection Type: IPv6 in IPv4 Tunnel In section to the user can configure the IPv6 connection to run in IPv4 Tunnel mode. IPv6 over IPv4 tunneling encapsulates IPv6 packets in IPv4 packets so that IPv6 packets can be sent over an IPv4 infrastructure. The following parameters will be available for configuration: Remote IPv4 Enter the remote IPv4 address used here. Address: Remote IPv6 Enter the remote IPv6 address used here.
Section 3 - Software Configuration The following parameters will be available for configuration: Enable DHCP-PD: Select this option to enable DHCP PD. LAN IPv6 Enter the LAN IPv6 address used here. This address must be Address: in the ‘/64’ subnet. LAN IPv6 Link- Displays the LAN IPv6 Link-Local address used here. Local Address: The following parameters will be available for configuration: Enable Automatic The user can tick this option to enable the auto-configuration IPv6 address: feature.
Section 3 - Software Configuration IPv6 Connection Type: 6to4 In this section the user can configure the IPv6 6to4 connection settings. 6to4 is an IPv6 address assignment and automatic tunneling technology that used to provide unicast IPv6 connectivity between IPv6 sites and hosts across the IPv4 Internet. The following parameters will be available for configuration: 6to4 Address: Here the 6to4 configured address will be displayed. 6to4 Relay: Enter the 6to4 relay address used here.
Section 3 - Software Configuration The following parameters will be available for configuration: Enable Automatic The user can tick this option to enable the auto-configuration IPv6 address: feature. Autoconfiguration The user can select the auto-configuration type used here. Type: IPv6 Address This option is only available when the auto-configuration Range (Start): type is set to Stateful. Enter the start IPv6 Address for the DHCPv6 range for your local computers.
Section 3 - Software Configuration IPv6 Connection Type: 6rd In this section the user can configure the IPv6 6rd connection settings. The following parameters will be available for configuration: 6rd Configuration: Select the desired 6rd configuration option here. 6rd IPv6 Prefix: Enter the 6rd IPv6 address and prefix value used here. IPv4 Address: Enter the IPv4 address used here. Mask Length: Enter the IPv4 mask length used here. Assigned IPv6 Displays the IPv6 assigned prefix value here.
Section 3 - Software Configuration The following parameters will be available for configuration: Enable Automatic The user can tick this option to enable the auto-configuration IPv6 address: feature. Autoconfiguration The user can select the auto-configuration type used here. Type: Router This option is only available when the auto-configuration Advertisement type is set to Stateless. Enter the router advertisement Lifetime: lifetime value used here.
Section 3 - Software Configuration Advanced Category In this category the user will be able to configure the more advanced features that can be done by this router. Features like Port Forwarding, Firewall settings, Quality of Service settings and more.
Section 3 - Software Configuration iTunes Server: The router features an iTunes Server. This server provides the ability to share music and videos to computers on the local network running iTunes. If the server is enabled, the router will be automatically detected by the iTunes program and the music and videos contained in the specified directory will be available to stream over the network. Guest Zone: On this page, the user will be able to configure the Guest Zone, settings.
Section 3 - Software Configuration Virtual Server This router can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The router’s firewall feature filters out unrecognized packets to protect the LAN network so all computers networked with the router are invisible to the outside world.
Section 3 - Software Configuration Port Forwarding The Port Forwarding option gives Internet users access to services on your LAN. This feature is useful for hosting online services such as FTP, Web or game servers. For each entry, you define a public port on your router for redirection to an internal LAN IP Address and LAN port. This option is used to open multiple ports or a range of ports in your router and redirect data through those ports to a single PC on your network.
Section 3 - Software Configuration Application Rules Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the router.
Section 3 - Software Configuration QoS Engine The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classified automatically. The QoS section contains a queuing mechanism, traffic shaping and classification. It supports two kinds of queuing mechanisms. Strict Priority Queue (SPQ) and Weighted Fair Queue (WFQ). SPQ will process traffic based on traffic priority.
Section 3 - Software Configuration After specifying the QoS framework used, in the QoS setup section, the user can now create individual rules for scenarios that require the use of traffic control and data priority manipulation. The following parameters will be available for configuration: Checkbox: Tick this option to enable the rule specified. Name: Enter a custom name for the rule being created here. This name is used for identification.
Section 3 - Software Configuration Network Filter The MAC (Media Access Controller) Address filter option is used to control network access based on the MAC Address of the network adapter. A MAC address is a unique ID assigned by the manufacturer of the network adapter. This feature can be configured to ALLOW or DENY network/Internet access. In the MAC Filtering Rules section, the user can create and edit Network filter rules. This maximum amount of rules that can be created are 24 rules.
Section 3 - Software Configuration Access Control The Access Control option allows you to control access in and out of your network. Use this feature as Access Controls to only grant access to approved sites, limit web access based on time or dates, and/or block internet access for applications like P2P utilities or games. The following parameters will be available for configuration: Enable Access Tick this option to enable the Access Control feature.
Section 3 - Software Configuration Step 2: In the second step, the user can configure the schedule settings for this rule. The following parameters will be available for configuration: Details: Select the appropriate predefined schedule rule to apply to this rule from the drop-down menu. Step 3: In the third step, the user can configure the address type and IP address of the machines used in this rule.
Section 3 - Software Configuration The following parameters will be available for configuration: Apply Web Filter: After selecting the ‘Block Some Access’ option, the user will be able to select this option. Selecting this option will allow the web filter access control feature to be applied to this rule. Apply Advanced After selecting the ‘Block Some Access’ option, the user Port Filters: will be able to select this option.
Section 3 - Software Configuration Website Filter Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network. Website Filter is used to allow or deny computers on your network from accessing specific web sites by keywords or specific Domain Names. Select ‘ALLOW computers access to ONLY these sites’ in order only allow computers on your network to access the specified URLs and Domain Names.
Section 3 - Software Configuration Parental Control Parental control is a free security option that provides Anti-Phishing to protect your Internet connection from fraud and navigation improvements such as auto-correction of common URL types. The following parameters will be available for configuration: Advanced DNS: Select this option to enable a fast and reliable DNS with minimal blocking of phishing sites only. No OpenDNS account required.
Section 3 - Software Configuration Inbound Filter The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can configure inbound data filtering rules that control data based on an IP address range. Inbound Filters can be used for limiting access to a server on your network to a system or group of systems. Filter rules can be used with Virtual Server, Port Forwarding, or Remote Administration features.
Section 3 - Software Configuration Firewall Settings A firewall protects your network from the outside world. The router offers a firewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
Section 3 - Software Configuration Firewall rules can be used to allow or deny traffic passing through the router. You can specify a single port by utilizing the input box at the top or a range of ports by utilizing both input boxes. DMZ means “Demilitarized Zone”. DMZ allows computers behind the router firewall to be accessible to Internet traffic. Typically, your DMZ would contain Web servers, FTP servers and others.
Section 3 - Software Configuration Routing The Routing option is an advanced method of customizing specific routes of data through your network. In the Routing List section, the user can configure routing rules used by this router. The maximum amount of rules that can be configured is 32. The following parameters will be available for configuration: Checkbox: To enable a route, check the box that is on the left side of the route. Name: Enter a name for the rule used here.
Section 3 - Software Configuration Advanced Wireless These options are for users that wish to change the behavior of their 802.11n wireless radio from the standard settings. We do not recommend changing these settings from the factory defaults. Incorrect settings may impact the performance of your wireless radio. The default settings should provide the best wireless radio performance in most environments.
Section 3 - Software Configuration Wi-Fi Protected Setup Wi-Fi Protected Setup (WPS) System is a simplified method for securing your wireless network during the “Initial setup” as well as the “Add New Device” processes. The WiFi Alliance (WFA) has certified it across different products as well as manufactures. The process is just as easy, as depressing a button for the Push-Button Method or correctly entering the 8-digit code for the Pin-Code Method.
Section 3 - Software Configuration Step 1: In this step the user have two options to choose from. You can choose Auto if the wireless client supports WPS, or Manual if the wireless client does not support WPS. Click on the Prev button to return to the previous page. Click on the Next button to continue to the next page. Click on the Cancel button to discard the changes made and return to the main wireless page. Step 2: After selecting Auto, the following page will appear.
Section 3 - Software Configuration Advanced Network This section contains settings which can change the way the router handles certain types of traffic. We recommend that you not change any of these settings unless you are already familiar with them or have been instructed to change them by one of our support personnel. UPnP UPnP is short for Universal Plug and Play which is a networking architecture that provides compatibility among networking equipment, software, and peripherals.
Section 3 - Software Configuration Multicast Streams This section enables the user to allow Multicast traffic to pass from the Internet to your network more efficiently. The following parameters will be available for configuration: Enable Multicast Enable this option if you are receiving video on demand type Streams: of service from the Internet.
Section 3 - Software Configuration DLNA Settings DLNA (Digital Living Network Alliance) is the standard for the interoperability of Network Media Devices (NMDs). The user can enjoy multi-media applications (music, pictures and videos) on your network connected PC or media devices. If you agree to share media with devices, any computer or device that connects to your network can play your shared music, pictures and videos. Note: The shared media may not be secure.
Section 3 - Software Configuration iTunes Server The router features an iTunes Server. This server provides the ability to share music and videos to computers on the local network running iTunes. If the server is enabled, the router will be automatically detected by the iTunes program and the music and videos contained in the specified directory will be available to stream over the network.
Section 3 - Software Configuration Guest Zone On this page, the user will be able to configure the Guest Zone, settings. The guest zone provide a separate network zone for guest to access Internet. The following parameters will be available for configuration: Enable Guest Tick this option to enable the Guest Zone feature for the Zone: frequency band 2.4GHz. Use the drop-down menu to schedule the time that the Firewall rule will be enabled.
Section 3 - Software Configuration IPv6 Firewall On this page the user can configure the IPv6 firewall settings. The firewall settings section is an advance feature that is used to allow or deny traffic from passing through the device. It works in the same way as IP Filters with additional settings. You can create more detailed rules for the device. In the IPv6 Firewall Rules section the user can create, enable and disable IPv6 firewall rules used by this device.
Section 3 - Software Configuration IPv6 Routing On this page the user can specify custom routes that determine how data is moved around your IPv6 network. The following parameters will be available for configuration: Checkbox: To enable a route, check the box that is on the left side of the route. Name: Enter the IPv6 routing rule name used here. Metric: Enter the metric value for this rule here.
Section 3 - Software Configuration Tools Category In this category the user will be able to configure features that are related to the router itself. Features like the time settings, login accounts, firmware update and more. The pages found in the Setup Category are: Admin: This page will allow you to change the Administrator password and configure the authentication settings. This window also allows you to enable Remote Management, via the Internet.
Section 3 - Software Configuration Admin This page will allow you to change the Administrator password and configure the authentication settings. This window also allows you to enable Remote Management, via the Internet. For security reasons, it is recommended that you change the password for the Admin and User accounts. Be sure to write down the new password to avoid having to reset the router in case they are forgotten.
Section 3 - Software Configuration Remote Admin Enter the remote administration port number used here. Sometimes services like an internal web server will occupy the port number 80. In this option Port: the user can change the remote administration port to 8080 for example. Remote Admin Select the appropriate remote admin inbound filter behavior here. Options to choose from are Allow All and Deny All. Inbound Filter: Details: Enter the remote admin inbound filter detail description used here.
Section 3 - Software Configuration Time The Time window allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to automatically adjust the time when needed. Time and Date Configuration Here the user can configure the time zone as well as the daylight savings settings used for this router.
Section 3 - Software Configuration Set the Time and Date Manually Here the user can configure the time and date values, used by this router, manually. Here the user can also synchronize the router’s time with the configuration computer’s time. The following parameters will be available for configuration: Set Manually: Here the user can manually configure the date and time used by this device. Options to configure are Year, Month, Day, Hour, Minute, and Second.
Section 3 - Software Configuration Email Settings The Email feature can be used to send the system log files and router alert messages to your email address. Email Notification When this option is enabled, router activity logs or firmware upgrade notifications can be emailed to a designated email address. The following parameters will be available for configuration: Enable Email Tick this option to enable the Email notification feature.
Section 3 - Software Configuration Email Log When Full or on Schedule Normally emails are sent at the starting and ending time defined in the schedule. However, rebooting the router during the schedule period will cause additional emails to be sent. The following parameters will be available for configuration: On Log Full: Select this option if you want logs to be sent by email when the log is full. On Schedule: Select this option if you want logs to be sent by email according to a schedule.
Section 3 - Software Configuration System This section allows you to manage the router’s configuration settings, reboot the router, and restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created.
Section 3 - Software Configuration Firmware Use the Firmware window to upgrade the firmware of the Router and install language packs. If you plan to install new firmware, make sure the firmware you want to use is on the local hard drive of the computer. If you want to install a new language pack, make sure that you have the language pack available. Please check the support site for firmware updates. You can download firmware upgrades to your hard drive from the support site.
Section 3 - Software Configuration Dynamic DNS The DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.
Section 3 - Software Configuration In the IPv6 Dynamic DNS List section, a list of IPv6 hosts will be displayed. Tick the Enable checkbox to make the host active. To edit a specific entry click on the icon. To remove a specific entry, click on the icon. Click on the Save Settings button to accept the changes made. Click on the Don’t Save Settings button to discard the changes made.
Section 3 - Software Configuration System Check This useful diagnostic utility can be used to check if a computer is on the Internet. It sends ping packets and listens for replies from the specific host. In the Ping Test section the user can test the Internet connectivity by entering in a host name or the IP address that you want to Ping and click on the Ping button. The status of your Ping attempt will be displayed in the Ping Result box.
Section 3 - Software Configuration Schedules Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm. The following parameters will be available for configuration: Name: Enter the custom name for the new schedule rule here. This name is used for identification.
Section 3 - Software Configuration Status Category In this category the user will be able to view information regarding the configuration and functionality of this device. Displays like WAN, LAN and Wireless configurations, System, Firewall and Router logs, and more. The pages found in the Setup Category are: Device Info: This page displays the current information for the router. It will display the LAN, WAN (Internet), and Wireless information.
Section 3 - Software Configuration Device Info This page displays the current information for the router. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. In the General section, information about the time and firmware is being displayed.
Section 3 - Software Configuration In the Wireless LAN section, information about the Wireless Local Area Network configuration is being displayed. In the LAN Computers section, a list of actively connected nodes are being displayed. In the IGMP Multicast Memberships section, a list of Multicast Group Addresses are being displayed.
Section 3 - Software Configuration Logs The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the router logs. You can define what types of events you want to view and the level of the events to view.
Section 3 - Software Configuration Statistics The screen below displays the Traffic Statistics. Here you can view the amount of packets that pass through the router on both the WAN, LAN ports and the 802.11n/g (2.4GHz) wireless band. The traffic counter will reset if the device is rebooted. In the LAN Statistics section, the user can view the traffic statistics that occurred on the LAN interface.
Section 3 - Software Configuration Internet Sessions The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer. In the section all the active Internet sessions will be displayed. Wireless The wireless client table displays a list of current connected wireless clients.
Section 3 - Software Configuration IPv6 The IPv6 page displays a summary of the Router’s IPv6 settings and lists the IPv6 address and host name of any IPv6 clients. In the IPv6 Connection Information section, more information about the IPv6 connection will be displayed. Information like the connection type, gateway address, Link-Local address, DNS Servers, and more. In the LAN IPv6 Computers section, a list of actively connected LAN IPv6 computers will be displayed.
Section 3 - Software Configuration Support Category In this category the user will have access to a portal of information regarding each and every page that exists on this device. This information gives the basic description of parameter and uses for the pages.
Section 4 - Knowledge Base Knowledge Base Wireless Basics Wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Section 4 - Knowledge Base Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Section 4 - Knowledge Base Tips Here are a few things to keep in mind, when you install a wireless network. Centralize your router or Access Point Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal to extend the range.
Section 4 - Knowledge Base Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The router offers wireless security options like WPA/WPA2 PSK/EAP. What is WPA? WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy). The 2 major improvements over WEP: • Improved data encryption through the Temporal Key Integrity Protocol (TKIP).
Section 4 - Knowledge Base Networking Basics Check your IP address After you install your new network or wireless adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter.
Section 4 - Knowledge Base Step 4 Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your router. Example: If the router’s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X where X is a number between 2 and 99. Make sure that the number you choose is not in use on the network. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1).
Section 4 - Knowledge Base Connect to a Wireless Network Using Window 7 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). 2. The utility will display any available wireless networks in your area. 3.
Section 4 - Knowledge Base 4. The following window appears while your computer tries to connect to the router. 5. Enter the same security key or passphrase that is on your router and click Connect. You can also connect by pushing the WPS button on the router. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 4 - Knowledge Base Using Window 7 and WPS The WPS feature of the router can be configured using Windows® 7. Carry out the following steps to use Windows® 7 to configure the WPS feature of the router: 1. Click the Start button and select Computer from the Start menu. 2. Click the Network option. 3. Double-click the Router. 4. Input the WPS PIN number and click Next.
Section 4 - Knowledge Base 5. Type a name to identify the network. 6. To configure advanced settings, click on the drop-down icon. Click Next to continue.
Section 4 - Knowledge Base 7. The following window appears while the Router is being configured. Wait for the configuration to complete. 8. The following window informs you that WPS on the Router has been setup successfully. Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future. 9. Click Close to complete WPS setup.
Section 4 - Knowledge Base Using Window Vista Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista® utility as seen below.
Section 4 - Knowledge Base Using Window XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Section 5 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the router. Read the following descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a different operating system, the screen captures on your computer will look similar to the following examples. Why can’t I access the web-based configuration utility? When entering the IP address of the router (192.168.0.
Section 5 - Troubleshooting What can I do if I forgot my password? If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the factory defaults. To reset the router, locate the reset button (hole) on the bottom panel of the unit. With the router powered on, use a paperclip to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30 seconds to access the router.
Appendix B - Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor. • Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Appendix B - Warranty original licensee for the non-conforming Software will be refunded by D-Link; provided that the non-conforming Software (and all copies thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given automatically terminates.
Appendix B - Warranty removed; Initial installation, installation and removal of the product for repair, and shipping costs; Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware or other products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or
Appendix B - Warranty Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective owners. Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc.
Appendix B - Warranty This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. Industry Canada statement This device complies with RSS-210 of the Industry Canada Rules.
Appendix B - Warranty 以下警語適用台灣地區 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 D-Link DIR-645 User Manual 122
Appendix C - Contacting Technical Support Contacting Technical Support U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. Before you contact technical support, please have the following ready: • Model number of the product (e.g. DIR-645) • Hardware Revision (located on the label on the bottom of the switch (e.g. rev A1)) • Serial Number (s/n number located on the label on the bottom of the device).
Appendix D - Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.
Industry Canada statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
以下警語適用台灣地區 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功 率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並 改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電 機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
