Version 1.
Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date Description 1.00 December 20, 2018 Initial A1 release Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
Table of Contents Table of Contents Product Overview............................................................... 1 Package Contents.......................................................................... 1 System Requirements.................................................................. 2 Introduction.................................................................................... 3 Features.............................................................................................
Table of Contents Windows® 8....................................................................................82 WPA/WPA2.............................................................................82 Windows® 7....................................................................................84 WPA/WPA2.............................................................................84 WPS...........................................................................................87 Windows Vista®............
Section 1 - Product Overview Product PackageOverview Contents DIR-1360 Quick Installation Document Ethernet Cable Power Adapter If any of the above items are missing or damaged, please contact your local reseller. Note: Using a power supply with a different voltage rating than the one included with the DIR-1360 will cause damage and void the warranty for this product.
Section 1 - Product Overview System Requirements Network Requirements • An Ethernet-based cable or DSL modem • IEEE 802.
Section 1 - Product Overview Introduction The D-Link DIR-1360 AC1300 Mesh-Enabled Smart Wi-Fi Router shares your Internet connection over a blazing-fast Gigabit Wireless AC connection of up to 1300 Mbps (Up to 867 Mbps on the 5 GHz Wireless AC band and up to 400 Mbps on the 2.4 GHz Wireless N band)1 by using advanced AC beamforming technology to significantly outperform 802.11n and other 802.11ac devices.
Section 1 - Product Overview Features • Superior Wireless Networking - The DIR-1360 provides Gigabit wireless speeds of up to a combined 1300 Mbps (867 Mbps 802.11ac 5 GHz, plus 400 Mbps 802.11n 2.4 GHz)1. These speeds rival wired connections and allow users enjoy online activities such as HD video communication, online gaming, and Voice over IP telephony lag-free from anywhere in your home while still offering full 802.11n/g/b backward compatibility.
Section 1 - Product Overview Hardware Overview LED Indicators 5 1 Power LED 2 Internet LED 3 4 5 Wireless (2.4 GHz LED) Wireless (5 GHz LED) USB 3.0 Port D-Link DIR-1360 User Manual 4 3 2 1 A solid blue light indicates a proper connection to the power supply. The light will be solid orange during boot up. A solid blue light indicates a connection on the Internet port. If the LED is orange, the router cannot connect to the Internet. A solid blue light indicates that the 2.
Section 1 - Product Overview Hardware Overview Back Panel 1 1 Reset Button 2 Gigabit LAN Ports (1- 4) 3 Gigabit WAN Port 4 WPS Button 5 Power Connector 6 Power Button D-Link DIR-1360 User Manual 2 3 4 5 6 Insert a paperclip in the hole to press the recessed button, hold for 10 seconds, and release to reset the router to default settings Connect Ethernet devices such as computers, switches, storage (NAS) devices, and game consoles.
Section 3 - Installation Installation This section will walk you through the installation of the DIR-1360. Before you Begin • Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, attic, or garage. This is to allow proper ventilation and prevent overheating. • Configure the router with the computer that was last connected directly to your Internet connection. Verify that it is connected to the Internet before connecting additional devices.
Section 3 - Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business.
Section 3 - Installation Hardware Setup 1. The DIR-1360 is designed to give you the fastest, most stable network connection possible. In order to maximize performance, fully extend the antennas into a 105-degree angle (middle notch) to provide optimal wireless coverage. Keep the router in an open area for better wireless coverage. 105˚ 2. Position your DIR-1360 near your Internet-connected modem. Place it in an open area for better wireless coverage. Modem DIR-1360 3.
Section 3 - Installation 4. Use the included Ethernet cable to connect your modem to the yellow port labeled INTERNET on the router. DIR-1360 Modem 5. Turn on or plug your modem back in and wait approximately one minute before proceeding onward. DIR-1360 Modem 6. Connect the supplied power adapter to the router and a power outlet, press the power button, and wait approximately one minute until the LED indicator on the front of the device changes from orange to solid blue.
Section 3 - Installation 7. If you are configuring the DIR-1360 wirelessly from a PC, connect to a Wi-Fi network printed on the included Wi-Fi Configuration Card. You can also find the Wi-Fi network names and passwords printed on the label attached to the bottom your router.
Section 3 - Installation Completing Setup There are different ways you can configure your router to connect to the Internet and connect to your clients: • D-Link Setup Wizard - This wizard will launch when you log into the router for the first time. Refer to Setup Wizard on page 13. • D-Link Wi-Fi App - Use your Android™ device, iPhone™ or IPad™ to configure your router. Refer to D-Link Wi-Fi App on page 17. • Manual Setup - Log in to the router and manually configure your router.
Section 3 - Installation Setup Wizard If this is your first time installing the router, open your web browser and enter http://dlinkrouter.local./ in the address bar. Alternatively, enter the IP address of the router (default: http://192.168.0.1). The wizard is designed to guide you through a step-by-step process to configure your new D-Link router and connect to the Internet. Click Next to continue. Please wait while your router detects your Internet connection type.
Section 3 - Installation Setup Wizard (continued) If the router detected or you selected PPPoE, enter your PPPoE username and password and click Next to continue. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. If the router detected or you selected Static, enter the IP and DNS settings supplied by your ISP. Click Next to continue.
Section 3 - Installation Setup Wizard (continued) Create a Wi-Fi password (between 8-63 characters). Your wireless clients will need to have this passphrase or key entered to be able to connect to your wireless network. Click Next to continue. Note: The DIR-1360's Smart Connect feature presents a single wireless network. When connecting clients to an extension network, they will be automatically added to the best band, either 2.4 GHz or 5 GHz.
Section 3 - Installation Setup Wizard (continued) You will be presented with a summary of your settings. Click Next to finalize the settings or Back to make changes. At the end of the wizard, you will be presented with a final summary of your settings. Click Finish to close the wizard.
Section 3 - Installation D-Link Wi-Fi App The D-Link Wi-Fi App allows you to install and configure your DIR-1360 AC1300 Mesh-Enabled Smart Wi-Fi Router from your mobile device. Note: The screenshots may be different depending on your mobile device’s OS version. The following steps show the Android interface of the D-Link Wi-Fi app. If you are using an iOS device, the appearance may be different from that of the screenshots, but the process is the same.
Section 3 - Installation D-Link Wi-Fi App (continued) Step 4 Select from list of options the device you want to install. If you do not see your device listed choose "Others" then tap NEXT. Step 5 You will now be guided through a step-by-step process for setting up your device. Simply follow the on-screen instructions to complete the installation and DIR-1360 configuration process.
Section 4 - Configuration Configuration To access the configuration utility, open a web-browser such as Internet Explorer and enter http://dlinkrouter.local./ or you may also connect by typing the IP address of the router (by default this is http://192.168.0.1) in the address bar. Enter your password. If you previously followed the setup wizard, please use the admin password you entered during the wizard. Otherwise, leave the password blank. Click Log In to proceed.
Section 4 - Configuration Home The Home page displays the current status of the router in the form of an interactive diagram. You can click each icon to display information about each part of the network at the bottom of the screen. The menu bar at the top of the page will allow you to quickly navigate to other pages. The Home page displays whether or not the router is currently connected to the Internet.
Section 4 - Configuration DIR-1360 Click on the DIR-1360 icon to view details about the router and its wireless settings. Here you can see the router’s current Wi-Fi network name and password, as well as the router's MAC address, IPv4 address, and IPv6 address. To reconfigure the network settings, either click Go to settings in the center, or click Settings (at the top of the page) and then Network on the menu that appears. Refer to Network on page 58 for more information.
Section 4 - Configuration Connected Clients Click on the Connected Clients icon to view details about the router and its wireless settings. On this page you can see all the clients currently connected to the router, and their IP addresses. To edit each client’s settings, click the pencil icon on the client you want to edit. Name: Enter a custom name for this client. Vendor: Displays the vendor of the device. MAC Address: Displays the MAC address of the device.
Section 4 - Configuration Settings Wizard In the Settings menu on the bar on the top of the page, click Wizard to open the setup wizard. This is the same wizard that appears when you start the router for the first time. Refer to Setup Wizard on page 13 for details. Internet In the Settings menu on the bar on the top of the page, click Internet to see the Internet configuration options. My Internet Choose your Internet connection type from the drop-down menu.
Section 4 - Configuration Dynamic IP (DHCP) Select Dynamic IP (DHCP) to obtain IP address information automatically from your Internet Service Provider (ISP). Select this option if your ISP does not specify an IP address to use. Advanced Settings Host Name: The host name is optional but may be required by some ISPs. Leave it blank if you are not sure. Primary DNS Enter the primary DNS server IP address assigned by your ISP. This Server: address is usually obtained automatically from your ISP.
Section 4 - Configuration Static IP Select Static IP if your IP information is provided by your Internet Service Provider (ISP). IP Address: Enter the IP address provided by your ISP. Subnet Mask: Enter the subnet mask provided by your ISP. Default Gateway: Enter the default gateway address provided by your ISP. Primary DNS Enter the primary DNS server IP address assigned by your ISP. Server: Advanced Settings Secondary DNS Enter the secondary DNS server IP address assigned by your ISP.
Section 4 - Configuration PPPoE Select PPPoE if your ISP provides and requires you to enter a PPPoE username and password in order to connect to the Internet. Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Reconnect Mode: Select either Always on, On Demand, or Manual. Maximum Idle Enter a maximum idle time during which the Internet connection is Time: maintained during inactivity. To disable this feature, select Always on as the reconnect mode.
Section 4 - Configuration PPPoE (continued) MAC Address The default MAC address is set to the Internet port’s physical interface Clone: MAC address on the router. You can use the drop-down menu to replace the Internet port’s MAC address with the MAC address of a connected client. Static IP IP Address: Enter the IP address provided by your ISP. Service Name: Enter the ISP service name (optional). Primary DNS Enter the primary DNS server IP address assigned by your ISP.
Section 4 - Configuration PPTP Choose PPTP (Point-to-Point-Tunneling Protocol) if your Internet Service Provider (ISP) uses a PPTP connection. Your ISP will provide you with a username and password. PPTP Server IP Enter the PPTP server IP address provided by your ISP. Address: Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Reconnect Mode: Select either Always on, On demand, or Manual.
Section 4 - Configuration PPTP (continued) Static IP PPTP IP Address: Enter the IP address provided by your ISP. PPTP Subnet Enter the subnet mask provided by your ISP. Mask: PPTP Gateway IP Enter the gateway IP address provided by your ISP. Address: Primary DNS Enter the primary DNS server IP address assigned by your ISP. Server: Secondary DNS Enter the secondary DNS server IP address assigned by your ISP.
Section 4 - Configuration L2TP Choose L2TP (Layer 2 Tunneling Protocol) if your Internet Service Provider (ISP) uses a L2TP connection. Your ISP will provide you with a username and password. L2TP Server: Enter the L2TP server IP address provided by your ISP. Username: Enter the username provided by your ISP. Password: Enter the password provided by your ISP. Reconnect Mode: Select either Always on, On demand, or Manual.
Section 4 - Configuration L2TP (continued) Static IP L2TP IP Address: Enter the IP address provided by your ISP. L2TP Subnet Enter the subnet mask provided by your ISP. Mask: L2TP Gateway IP Enter the gateway IP address provided by your ISP. Address: Primary DNS Enter the primary DNS server IP address assigned by your ISP. Server: Secondary DNS Enter the secondary DNS server IP address assigned by your ISP.
Section 4 - Configuration DS-Lite DS-Lite is an IPV4/IPv6 hybrid connection type. After selecting DS-Lite, the following parameters will be available for configuration: Advanced Settings DS-Lite Select DS-Lite DHCPv6 Option to let the router allocate the AFTR Configuration: IPv6 address automatically. Select Manual Configuration to enter the AFTR IPv6 address manually. DS-Lite DHCPv6 B4 IPv6 Address: Enter the B4 IPv4 address value used here.
Section 4 - Configuration IPv6 To configure an IPv6 connection, click the IPv6 link. To return to the IPv4 settings, click IPv4. My Internet Choose your IPv6 connection type from the drop-down menu. You Connection Is: will be presented with the appropriate options for your connection type. Click Advanced Settings... to expand the list and see all of the options. For Auto Detection refer to page 34. For Static IPv6 refer to page 36. For Auto Configuration (SLAAC/DHCPv6) refer to page 38.
Section 4 - Configuration Auto Detection Select Auto Detection to automatically detect the IPv6 connection method used by your Internet Service Provider (ISP). If Auto Detection fails, you can manually select another IPv6 connection type. IPv6 DNS Settings DNS Type: Select either Obtain DNS server address automatically or Use the following DNS address. If Use the following DNS address is selected: Primary DNS If you selected Use the following DNS address above, enter the Server: primary DNS server address.
Section 4 - Configuration Auto Detection (continued) Advanced Settings - Address Autoconfiguration Settings Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature. IPv6 Address Assignment: Enable Automatic Enable or disable DHCP-PD for other IPv6 routers connected to the DHCP-PD in LAN: LAN interface. Note: This feature requires a smaller subnet prefix than /64 (i.e. allowing for a larger address allocation), such as /63. Contact your ISP for more information.
Section 4 - Configuration Static IPv6 Select Static IP if your IPv6 information is provided by your Internet Service Provider (ISP). IPv6 DNS Settings If Use the following DNS address is selected for DNS Type: Primary DNS Enter the primary DNS server address. Server: Secondary DNS Enter the secondary DNS server address.
Section 4 - Configuration Static IPv6 (continued) If you selected Stateful DHCPv6 as the Autoconfiguration Type: IPv6 Address Enter the starting IPv6 address for the DHCP server’s IPv6 assignment. Range (Start): IPv6 Address Enter the ending IPv6 address for the DHCP server’s IPv6 assignment. Range (End): Click Save when you are done.
Section 4 - Configuration Auto Configuration (SLAAC/DHCPv6) Select Auto Configuration if your ISP assigns your IPv6 address when your router requests one from the ISP’s server. Some ISPs require you to adjust settings on your side before your router can connect to the IPv6 Internet. IPv6 DNS Settings DNS Type: Select either Obtain DNS server address automatically or Use the following DNS address. If Use the following DNS address is selected: Primary DNS Enter the primary DNS server address.
Section 4 - Configuration Auto Configuration (SLAAC/DHCPv6) (continued) Advanced Settings - Address Autoconfiguration Settings Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature. IPv6 Address Assignment: If DHCP-PD is enabled in LAN IPv6 Address Settings: Enable Automatic Enable or disable DHCP-PD for other IPv6 routers connected to the DHCP-PD in LAN: LAN interface. Note: This feature requires a smaller subnet prefix than /64 (i.e.
Section 4 - Configuration Auto Configuration (SLAAC/DHCPv6) (continued) If DHCP-PD is disabled in LAN IPv6 Address Settings and SLAAC+Stateless DHCP or SLAAC+RDNSS is chosen as the Autoconfiguration Type: Router Enter the router advertisement lifetime (in minutes). Advertisement Lifetime: If DHCP-PD is disabled in LAN IPv6 Address Settings and Stateful DHCPv6 is chosen as the Autoconfiguration Type: IPv6 Address Enter the starting IPv6 address for the DHCP server’s IPv6 assignment.
Section 4 - Configuration PPPoE Select PPPoE if your ISP provides and requires you to enter a PPPoE username and password in order to connect to the Internet. PPPoE Session: Choose Share with IPv4 to re-use your IPv4 PPPoE username and password, or Create a new session. Address Mode: Select Static IP if your ISP assigned you an IP address. In most cases, select Dynamic IP. MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your ISP.
Section 4 - Configuration PPPoE (continued) If you selected Static IP as the Address Mode and Create a new session as the PPPoE Session: IP Address: Enter the IP address provided by your ISP Service Name: Enter the ISP service name (optional). Reconnect Mode: Select either Always-on or Manual. MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your ISP.
Section 4 - Configuration PPPoE (continued) If Enable DHCP-PD is disabled these additional parameters are available for configuration: LAN IPv6 Address: If DHCP-PD disabled or static address mode is selected, enter the LAN (local) IPv6 address for the router. LAN IPv6 Link- Displays the router’s LAN link-local address. Local Address: Advanced Settings - Address Autoconfiguration Settings Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature.
Section 4 - Configuration PPPoE (continued) If you selected Stateful DHCPv6 as the Autoconfiguration Type: IPv6 Address Enter the starting IPv6 address for the DHCP server’s IPv6 assignment. Range (Start): IPv6 Address Enter the ending IPv6 address for the DHCP server’s IPv6 assignment. Range (End): If DHCP-PD is disabled in LAN IPv6 Address Settings: IPv6 Address Enter the starting IPv6 address for the DHCP server’s IPv6 assignment.
Section 4 - Configuration IPv6 in IPv4 Tunnel The user can configure the IPv6 connection to run in IPv4 Tunnel mode. IPv6 over IPv4 tunnelling encapsulates IPv6 packets in IPv4 packets so that IPv6 packets can be sent over an IPv4 infrastructure. Remote IPv4 Enter the IPv4 remote address you will use. Address: Remote IPv6 Enter the IPv6 remote address you will use. Address: Local IPv4 Displays the current local IPv4 address. Address: Local IPv6 Enter the IPv6 local address you will use.
Section 4 - Configuration IPv6 in IPv4 Tunnel (continued) LAN IPv6 Address Settings Enable DHCP-PD: Enable or disable prefix delegation services. This option is only available if you selected Dynamic IP for address mode. LAN IPv6 Link- Displays the router’s LAN link-local address.
Section 4 - Configuration IPv6 in IPv4 Tunnel (continued) If you selected SLAAC+RDNSS or SLAAC+Stateless DHCP as the Autoconfiguration Type: Router Enter the router advertisement lifetime (in minutes). Advertisement Lifetime: If you selected Stateful DHCPv6 as the Autoconfiguration Type: IPv6 Address Enter the starting IPv6 address for the DHCP server’s IPv6 assignment. Range (Start): IPv6 Address Enter the ending IPv6 address for the DHCP server’s IPv6 assignment.
Section 4 - Configuration 6to4 In this section the user can configure the IPv6 6 to 4 connection settings. 6to4 is an IPv6 address assignment and automatic tunneling technology that is used to provide unicast IPv6 connectivity between IPv6 sites and hosts across the IPv4 Internet. 6to4 Address: Displays the 6 to 4 address. 6to4 Relay: Enter the 6 to 4 relay supplied by your ISP. Primary DNS Enter the primary DNS server address. Server: Secondary DNS Enter the secondary DNS server address.
Section 4 - Configuration 6to4 (continued) Advanced Settings - Address Autoconfiguration Settings Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature. IPv6 Address Assignment: Autoconfiguration Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6. Type: If you selected SLAAC+RDNSS or SLAAC+Stateless DHCP as the Autoconfiguration Type: Router Enter the router advertisement lifetime (in minutes).
Section 4 - Configuration 6rd In this section the user can configure the IPv6 6rd connection settings. Assign IPv6 Prefix: Currently unsupported. Primary DNS Enter the primary DNS server address. Server: Secondary DNS Enter the secondary DNS server address. Server: 6rd Manual Configuration Enable Hub and Enable this option if you want to minimize the number of routes to Spoke Mode: the destination by using a hub and spoke method of networking.
Section 4 - Configuration 6rd (continued) Advanced Settings - Address Autoconfiguration Settings Enable Automatic Enable or disable the Automatic IPv6 Address Assignment feature. IPv6 Address Assignment: Autoconfiguration Select SLAAC+RDNSS, SLAAC+Stateless DHCP, or Stateful DHCPv6. Type: If you selected SLAAC+RDNSS or SLAAC+Stateless DHCP as the Autoconfiguration Type: Router Enter the router advertisement lifetime (in minutes).
Section 4 - Configuration Local Connectivity Only Local Connectivity Only allows you to set up an IPv6 connection that will not connect to the Internet. Advanced Settings IPv6 ULA Settings Enable ULA: Click here to enable Unique Local IPv6 Unicast Addresses settings. Use Default ULA Enable this option to use the default ULA prefix. Prefix: If you selected Enable ULA and disabled Default ULA Prefix: ULA Prefix: Enter your own ULA prefix.
Section 4 - Configuration VLAN VLAN allows for services such as Triple-Play to be used, and divides a network into segments that can only be accessed by other devices in the same VLAN. In the Settings menu on the bar on the top of the page, click Internet, then click the VLAN link. Triple-Play Status: Click to enable or disable the Triple-Play VLAN feature. If Status is enabled: Internet VLAN ID Enter the VLAN ID for your Internet connection, as provided by your ISP.
Section 4 - Configuration Wireless From this page you can configure your wireless network settings. Smart Connect Smart Connect: Enable or disable the Smart Connect Feature. When enabled, only a few configuration options are available to simplify configuration. Wi-Fi Name (SSID): Create a name for your wireless network using up to 32 characters. Password: Create a password to use for wireless security. Wireless clients will need to enter this password to successfully connect to the network.
Section 4 - Configuration Wireless - Smart Connect Disabled If Smart Connect is disabled the following options are available: 2.4GHz / 5GHz Status: Enable or disable the 2.4 GHz / 5 GHz wireless network. Wi-Fi Name (SSID): Create a name for your wireless network using up to 32 characters. Password: Create a password to use for wireless security. Advanced Settings Security Mode: Choose None or WPA/WPA2-Personal (recommended). 802.11 Mode Select the desired wireless networking standards to use. (2.
Section 4 - Configuration HT20/40 Enable or disable HT20/40 Coexistence. Coexistence: (2.4 GHz): Visibility Status: The default setting is Visible. Select Invisible if you do not want to broadcast the SSID of your wireless network. Schedule: Use the drop-down menu to select the time schedule that the rule will be enabled for. The schedule may be set to Always Enable, or you can create your own schedules in the Schedules section. Refer to Schedule on page 72 for more information.
Section 4 - Configuration Guest Zone The Guest Zone feature will allow you to create temporary zones that can be used by guests to access the Internet. These zones will be separate from your main wireless network. You may configure different zones for the 2.4 GHz and 5 GHz wireless bands. Note: If Smart Connect is enabled, Guest Zone is unavailable. In the Settings menu on the bar on the top of the page, click Wireless, then click the Guest Zone link. 2.4 GHz / 5 GHz Status: Enable or disable the 2.
Section 4 - Configuration Network This section will allow you to change the local network settings of the router and to configure the DHCP settings. In the Settings menu on the bar on the top of the page, click Network. Click Advanced Settings... to expand the list and see all of the options. Network Settings LAN IP Address: Enter the IP address of the router. The default IP address is 192.168.0.1.
Section 4 - Configuration Network (continued) DHCP Server Status: Enable or disable the DHCP server. DHCP IP Address Enter the starting and ending IP addresses for the DHCP server’s IP Range: assignment. Note: If you statically (manually) assign IP addresses to your computers or devices, make sure the IP addresses are outside of this range or you may have an IP conflict. DHCP Lease Time: Enter the length of time for the IP address lease in minutes.
Section 4 - Configuration Features QoS Engine This Quality of Service (QoS) Engine will allow you to prioritize particular clients over others, so that those clients receive higher bandwidth. For example, if one client is streaming a movie and another is downloading a nonurgent file, you might wish to assign the former device a higher priority than the latter so that the movie streaming is not disrupted by the traffic of the other devices on the network.
Section 4 - Configuration Firewall The router’s firewall protects your network from malicious attacks over the Internet. In the Features menu on the bar on the top of the page, click Firewall. Click Advanced Settings... to expand the list and see all of the options. Enable DMZ: Enable or disable Demilitarized Zone (DMZ). This completely exposes the client to threats over the Internet, and is not recommended in ordinary situations.
Section 4 - Configuration Firewall Settings (continued) Advanced Settings - Application Level Gateway (ALG) Configuration PPTP: Allows multiple machines on the LAN to connect to their corporate network using the PPTP protocol. IPSec (VPN): Allows multiple VPN clients to connect to their corporate network using IPSec. Some VPN clients support traversal of IPSec through NAT. This Application Level Gateway (ALG) may interfere with the operation of such VPN clients.
Section 4 - Configuration IPv4/IPv6 Rules The IPv4/IPv6 Rules section is an advanced option that lets you configure what kind of traffic is allowed to pass through the network. To configure the IPv4 rules, from the Firewall Settings page click IPv4 Rules. To configure IPv6 rules, from the Firewall Settings page click IPv6 Rules. To return to the main Firewall Settings page, click Advanced. To begin, use the drop-down menu to select whether you want to ALLOW or DENY the rules you create.
Section 4 - Configuration Port Forwarding Port forwarding allows you to specify a port or range of ports to open for specific devices on the network. This might be necessary for certain applications to connect through the router. In the Features menu on the bar on the top of the page, click Port Forwarding. If you wish to remove a rule, click on its trash can icon in the Delete column. If you wish to edit a rule, click on its pencil icon in the Edit column.
Section 4 - Configuration Virtual Server The virtual server allows you to specify a single public port on your router for redirection to an internal LAN IP address and Private LAN port. To configure the virtual server, from the Port Forwarding page click Virtual Server. To return to the main Port Forwarding page, click Port Forwarding. If you wish to remove a rule, click on its trash can icon in the Delete column. If you wish to edit a rule, click on its pencil icon in the Edit column.
Section 4 - Configuration Website Filter The website filter settings allow you to block access to certain web sites. You can either create a list of sites to block, or create a list of sites to allow (with all other sites being blocked). In the Features menu on the bar on the top of the page, click Website Filter. If you want to create a list of sites to block, select DENY client access to ONLY these sites from the drop-down menu. All other sites will be accessible.
Section 4 - Configuration Static Routes The Static Routes section allows you to define custom routes to control how data traffic is moved around your network. In the Features menu on the bar on the top of the page, click Static Route. To configure IPv6 rules, click IPv6 and refer to IPv6 on page 68. To return to the main IPv4 static routes page, click IPv4. If you wish to remove a rule, click on the corresponding trash can icon in the Delete column.
Section 4 - Configuration IPv6 To configure IPv6 rules, on the Static Routes page click IPv6. To return to the main IPv4 static routes page, click IPv4. If you wish to remove a rule, click on its trash can icon in the Delete column. If you wish to edit a rule, click on its pencil icon in the Edit column. If you wish to create a new rule, click the Add Rules button. Click Save when you are done. If you edit or create a rule, the following options will appear: Name: Enter a name for the rule.
Section 4 - Configuration Dynamic DNS Most Internet Service Providers (ISPs) assign dynamic (changing) IP addresses. Using a dynamic DNS service provider, people can enter your domain name in their web browser to connect to your server no matter what your IP address is. In the Features menu on the bar on the top of the page, click Dynamic DNS. Enable Dynamic Enable or disable dynamic DNS. Enabling this feature will reveal DNS: further configuration options.
Section 4 - Configuration IPv6 Host The IPv6 host settings are found at the bottom of the Dynamic DNS page. If you wish to remove a rule, click on its trash can icon in the Delete column. If you wish to edit a rule, click on its pencil icon in the Edit column. If you wish to create a new rule, click the Add Record button. Click Save when you are done. If you edit or create a rule, the following options will appear: Host Name: Enter the host name that you registered with your dynamic DNS service provider.
Section 4 - Configuration Management Time & Schedule Time The Time page allows you to configure, update, and maintain the correct time on the internal system clock. From here you can set the time zone, the Network Time Protocol (NTP) server, and enable or disable daylight saving time. In the Management menu on the bar on the top of the page, click Time & Schedule. Time Configuration Time Zone: Select your time zone from the drop-down menu. Time: Displays the current date and time of the router.
Section 4 - Configuration Schedule Some router functions can be controlled through a pre-configured schedule. To create, edit, or delete schedules, from the Time page click Schedule. To return to the Time page, click Time. If you wish to remove a rule, click on its trash can icon in the Delete column. If you wish to edit a rule, click on its pencil icon in the Edit column. If you wish to create a new rule, click the Add Rule button. Click Save when you are done.
Section 4 - Configuration System Log The router keeps a running log of events. This log can be sent to a Syslog server, or sent to your email address. In the Management menu on the bar on the top of the page, click System Log. Log Settings System Log Click the Check System Log button to download a text file containing the system log. SysLog Settings Enable Logging to Check this box to send the router logs to a SysLog Server.
Section 4 - Configuration System Log (continued) SMTP Server Port: Enter your SMTP server port. Enable Check this box if your SMTP server requires authentication. Authentication: Account Name: Enter your SMTP account name. Password: Enter your SMTP account's password E-mail Log When Full or On Schedule Send When Log If enabled, this option will set the router to send the log when it is full. Full: Send on Schedule: If enabled, this option will set the router to send according to a set schedule.
Section 4 - Configuration System Admin This page will allow you to change the administrator (Admin) password and enable remote management. In the Management menu on the bar on the top of the page, click System Admin. To load, save, reset settings, or reboot the router, click System and refer to Schedule on page 72. Admin Password Password: Enter a new password for the administrator account. You will need to enter this password whenever you configure the router using a web browser.
Section 4 - Configuration System This page allows you to save the router’s current configuration, load a previously saved configuration, reset the router to its factory default settings, or reboot the router. From the Admin page, click System. To return to the Admin page, click Admin. System Save Settings To This option will save the current router configuration settings to a file Local Hard Drive: on your computer. Load Settings This option will load a previously saved router configuration file.
Section 4 - Configuration Upgrade This page will allow you to upgrade the router’s firmware, either automatically or manually. To manually upgrade the firmware, you must first download the relevant file from http://support.dlink.com. In the Management menu on the bar on the top of the page, click Upgrade. Firmware Information Current Firmware The current firmware's version and date will be displayed.
Section 4 - Configuration Statistics On the Statistics page you can view the amount of packets that pass through the router on the WAN, LAN, and wireless segments. In the Management menu on the bar on the top of the page, click Statistics. You can view the Internet, LAN, Wi-Fi 2.4 GHz, or Wi-Fi 5 GHz by clicking on the respective tabs at the top. The graph will update in real time. To clear the information on the graph, click Clear. The traffic counter will reset if the device is rebooted.
Section 6- Connecting a Wireless Client Connect a Wireless Client to your Router WPS Button The easiest and most secure way to connect your wireless devices to the router is with WPS (Wi-Fi Protected Setup). Most wireless devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button (or a software utility with WPS) that you can press to connect to the DIR-1360 router.
Section 6- Connecting a Wireless Client Windows® 10 When connecting to the DIR-1360 wirelessly for the first time, you will need to input the wireless network name (SSID) and Wi-Fi password (security key) of the device you are connecting to. If your product has a Wi-Fi configuration card, you can find the default network name and Wi-Fi password here. Otherwise refer to the product label for the default Wi-Fi network SSID and password, or enter the Wi-Fi credentials set during the product configuration.
Section 6- Connecting a Wireless Client To connect to the SSID, click Connect. To automatically connect with the router when your device next detects the SSID, click the Connect Automatically check box. You will then be prompted to enter the Wi-Fi password (network security key) for the wireless network. Enter the password into the box and click Next to connect to the network. Your computer will now automatically connect to this wireless network when it is detected.
Section 6- Connecting a Wireless Client Windows® 8 WPA/WPA2 It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key (Wi-Fi password) being used. To join an existing network, locate the wireless network icon in the taskbar next to the time display.
Section 6- Connecting a Wireless Client You will then be prompted to enter the network security key (Wi-Fi password) for the wireless network. Enter the password into the box and click Next. If you wish to use Wi-Fi Protected Setup (WPS) to connect to the router, you can also press the WPS button on your router during this step to enable the WPS function.
Section 6- Connecting a Wireless Client Windows® 7 WPA/WPA2 It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. Click on the wireless icon in your system tray (lower-right corner). Wireless Icon The utility will display any available wireless networks in your area.
Section 6- Connecting a Wireless Client Highlight the wireless connection with Wi-Fi name (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. The following window appears while your computer tries to connect to the router.
Section 6- Connecting a Wireless Client Enter the same security key or passphrase (Wi-Fi password) that is on your router and click Connect. You can also connect by pushing the WPS button on the router. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as the one on the wireless router.
Section 6- Connecting a Wireless Client WPS The WPS feature of the DIR-1360 can be configured using Windows® 7. Carry out the following steps to use Windows® 7 to configure the WPS feature: Click the Start button and select Computer from the Start menu. Click Network on the left side.
Section 6- Connecting a Wireless Client Double-click the DIR-1360. DIR-1360 Input the WPS PIN number (on the router label) in the Setup > Wireless Setup menu in the Router’s Web UI) and click Next.
Section 6- Connecting a Wireless Client Type a name to identify the network. To configure advanced settings, click the icon. Click Next to continue.
Section 6- Connecting a Wireless Client The following window appears while the DIR-1360 is being configured. Wait for the configuration to complete. The following window informs you that WPS on the DIR-1360 has been set up successfully. Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future. Click Close to complete WPS setup.
Section 6- Connecting a Wireless Client Windows Vista® Windows Vista® users may use the built-in wireless utility. If you are using another company’s wireless utility, please refer to the user manual of your wireless adapter for help connecting to a wireless network. Most wireless utilities will have a “site survey” option similar to the Windows Vista® utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility.
Section 6- Connecting a Wireless Client WPA/WPA2 It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network.
Section 6- Connecting a Wireless Client Enter the same security key or passphrase (Wi-Fi password) that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as the one on the wireless router.
Section 7 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DIR-1360. Read the following descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to these examples. 1. Why can’t I access the web-based configuration utility? When entering the IP address of the D-Link router (192.168.0.
Section 7 - Troubleshooting • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Section 7 - Troubleshooting 3. Why can’t I connect to certain sites or send and receive emails when connecting through my router? If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be another computer, or a URL.
Section 7 - Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size.
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business, or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when, and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Appendix A - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford.
Appendix A - Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power. This makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere, not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Appendix A - Wireless Basics Wireless Modes There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router. • Ad-hoc – Directly connecting to another computer for peer-to-peer communication using wireless network adapters on each computer, such as two or more DIR-1360 wireless network USB adapters. An Infrastructure network contains an access point or wireless router.
Appendix B - Networking Basics Check your IP address Networking Basics After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. In Windows, type cmd in the Start Search box and click OK. At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter.
Appendix B - Networking Basics Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DIR-1360 offers the following types of security: • WPA2 (Wi-Fi Protected Access 2) • WPA (Wi-Fi Protected Access) • WPA2-PSK (Pre-Shared Key) • WPA-PSK (Pre-Shared Key) What is WPA? WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
Appendix C - Technical Specifications Technical Specifications Device Interfaces • Wireless Interface (2.4 GHz): IEEE 802.11 b/g/n • Wireless Interface (5 GHz): IEEE 802.11 a/n/ac • Four 10/100/1000 Mbps LAN ports • One 10/100/1000 Mbps WAN port Antenna Types • Four fixed external antennas Standards • IEEE 802.11ac1,2,3 • IEEE 802.11n • IEEE 802.11g • IEEE 802.11b • IEEE 802.11a • IEEE 802.11d • IEEE 802.3u • IEEE 802.
Appendix D - Regulatory Information Regulatory Information Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
Appendix D - Regulatory Information Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Appendix D - Regulatory Information NCC 警語： 以下警語適用台灣地區 依據 低功率電波輻射性電機管理辦法 第十二條: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變 更原設計之特性及功能。 第十四條: 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至 無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工 業、科學及醫療用電波輻射性電機設備之干擾。 無線傳輸設備 (UNII) 在 5.25-5.
