Section 3 - Configuration IPv6 IPv6 over IPv4 Tunnel - Stateful Enable automatic Check to enable the automatic IPv6 address assignment IPv6 address feature. assignment: Autoconfiguration Select Stateful (DHCPv6). Refer to the next page for Type: Stateless. IPv6 Address Enter the start IPv6 Address for the DHCPv6 range for your Range Start: local computers. IPv6 Address Enter the end IPv6 Address for the DHCPv6 range for your Range End: local computers.
Section 3 - Configuration IPv6 Link-local Only Select Link-local Only from the My IPv6 Connection is drop-down menu if your Router will use the IPv6 link local method to connect to the Internet. LAN IPv6 Displays the LAN IPv6 Link-Local address of the router. Address Settings: Click the Save Settings button to save any changes made.
Section 3 - Configuration IPv6 PPPoE The DHP-1320’s IPv6 Firewall feature allows you to configure which kind of IPv6 traffic is allowed to pass through the device. The DHP-1320’s IPv6 Firewall functions in a similar way to the IP Filters feature. My IPv6 Select PPPoE from the drop-down menu. Connection: PPPoE: Enter the PPPoE account settings supplied by your Internet provider (ISP). Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses.
Section 3 - Configuration IPv6 DNS Settings: Select either Obtain DNS server address automatically or Use the following DNS Address. Primary/Secondary Enter the primary and secondary DNS server addresses. DNS Address: LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN Link-Local Displays the Router’s LAN Link-Local Address. Address: Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Select Stateful (DHCPv6) or Stateless.
Section 3 - Configuration IPv6 Routing This page allows you to specify custom routes that determine how data is moved around your network. Routing List: Each Route has a checkbox next to it, check the box of the route you wish to enable. Name: Specify a name for identification of this route. Destination IP: This field identifies the portion of the destination IP in use. Metric: The route metric is a value from 1 to 16 that indicates the cost of using this route.
Section 3 - Configuration Tools Admin This page will allow you to change the Administrator password and configure the authentication settings. This window also allows you to enable Remote Management, via the Internet. Admin Enter a new password for the Administrator Login Name. Password: The administrator can make changes to the settings. User Password: Enter the new password for the User login. If you login as the User, you can only see the settings, but cannot change them.
Section 3 - Configuration Time The Time window allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to automatically adjust the time when needed. Time Zone: Select the Time Zone from the drop-down menu. Enable Daylight Check this box if the country your are located in uses Saving: Daylight Saving time.
Section 3 - Configuration SysLog The Broadband Router keeps a running log of events and activities occurring on the Router. You may send these logs to a SysLog server on your network. Enable Logging Check this box to send the router logs to a SysLog Server. to SysLog Server: SysLog Server The address of the SysLog server that will be used to IP Address: send the logs. You may also select your computer from the drop-down menu (only if receiving an IP address from the router via DHCP).
Section 3 - Configuration Email Settings The Email feature can be used to send the system log files and router alert messages to your email address. Enable Email When this option is enabled, router activity logs are Notifications: e-mailed to a designated e-mail address. From Email This email address will appear as the sender when you Address: receive a log file or firmware upgrade notification via email. To Email Address: Enter the email address where you want the email sent.
Section 3 - Configuration System This section allows you to manage the router’s configuration settings, reboot the router, and restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created. Save Settings to Use this option to save the current router configuration Local Hard Drive: settings to a file on the hard disk of the computer you are using. First, click the Save button.
Section 3 - Configuration Firmware Use the Firmware window to upgrade the firmware of the Router and install language packs. If you plan to install new firmware, make sure the firmware you want to use is on the local hard drive of the computer. If you want to install a new language pack, make sure that you have the language pack available. Please check the D-Link support site for firmware updates at http://support.dlink.com.
Section 3 - Configuration Dynamic DNS The DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased (www.whateveryournameis. com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.
Section 3 - Configuration System Check Ping Test: The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP Address that you wish to Ping, and click Ping. Click Stop to stop sending Ping packets IPv6 Ping The IPv6 Ping Test is used to send IPv6 Ping packets to test Test: if a computer is on the Internet. Enter the IPv6 Address that you wish to Ping, and click Ping.
Section 3 - Configuration Schedules Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm. Name: Enter a name for your new schedule. Days: Select a day, a range of days, or All Week to include every day. Time: Check All Day - 24hrs or enter a Start Time and End Time for your schedule.
Section 3 - Configuration Status Device Info This page displays the current information for the DHP-1320. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed.
Section 3 - Configuration Logs The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the router logs. You can define what types of events you want to view and the level of the events to view.
Section 3 - Configuration Statistics The screen below displays the Traffic Statistics. Here you can view the amount of packets that pass through the DHP-1320 on both the WAN, LAN ports and the 802.11n/g (2.4GHz) wireless band. The traffic counter will reset if the device is rebooted. Refresh: Click the Refresh button to refresh the Router’s traffic statistics. Reset: Click the Reset button to reset the Router’s traffic statistics.
Section 3 - Configuration Internet Sessions The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer.
Section 3 - Configuration Routing Table This page displays the routing details configured for your router.
Section 3 - Configuration Wireless The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients.
Section 3 - Configuration IPv6 The IPv6 page displays a summary of the Router’s IPv6 settings and lists the IPv6 address and host name of any IPv6 clients.
Section 3 - Configuration Support D-Link DHP-1320 User Manual 102
Section 4 - Security Wireless Connection Setup Wizard To run the Wireless Connection Setup Wizard, click the Wireless Connection Setup Wizard button in the Setup>Wireless Settings window.
Section 4 - Security Wireless Security Setup Wizard Check the Manually set 5GHz band Network Name... box to manually set your desired wireless network name for the 5GHz band. Type your desired wireless network name (SSID). Automatically: Select this option to automatically generate the router’s network key and click Next. Manually: Select this option to manually enter your network key and click Next. If you selected Automatically, the summary window will display your settings.
Section 4 - Security If you selected Manually, the following screen will appear. Enter the Wireless Security Password you would like to use for your wireless network and click Next to proceed to the next window. The summary window will display your settings. Write down the security key and enter this on your wireless clients. Click Save to save your settings.
Section 4 - Security Add Wireless Device with WPS Wizard From the Setup > Wireless Settings screen, click Add Wireless Device with WPS. Select Auto to add a wireless client using WPS (Wi-Fi Protected Setup). Once you select Auto and click Connect, you will have a 120 second time limit to apply the settings to your wireless client(s) and successfully establish a connection. If you select Manual, a settings summary screen will appear. Write down the security key and enter this on your wireless clients.
Section 3 - Configuration Configuration (AP Mode) This section will show you how to configure your new D-Link wireless router using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter http://dlinkrouter or the IP address of the router (192.168.0.1). Select Admin in the User Name field. Leave the password blank by default.
Section 3 - Configuration Wireless Setup Wizard To use our web-based wizard to assit you in connecting your DHP-1320, click Launch Wireless Setup Wizard to begin. Click Next to continue your wireless network setup. Select one of the two configuration methods. Select WPS if your wireless device support WPS and click Next to continue to the next step. Press down the Push Button on the wireless device within 116 seconds.
Section 3 - Configuration If you would like to setup your network manually, select Manual and click Next to continue. Enter the SSID (Service Set Identifier). The SSID is the name of your wireless network. Create a name using up to 32 characters. The SSID is casesensitive. Select Assign a network key and click Next. Once this screen appears, the setup is complete. You will be given a detailed summary of your wireless security settings. Click Save to continue.
Section 3 - Configuration Wireless Setup Enable Check this box to enable the wireless function. If you Wireless: would prefer not to use wireless, uncheck the box to disable all the wireless functions. You may also set up a specific time range (schedule). Select a schedule from the drop-down menu or click Add New Schedule to create a new schedule.
Section 3 - Configuration Channel Width: Select the Channel Width: Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices. 20MHz - Select if you are not using any 802.11n wireless clients. Wireless Security Locking the wireless security settings prevents the settings from being changed by any new external user using its PIN. Devices Settings: can still be added to the wireless network using Wi-Fi Protected Setup.
Section 3 - Configuration Network Settings - DHCP This section will allow you to change the local network settings of the access point and to configure the DHCP settings. LAN Connection Use the drop-down menu to select Dynamic IP (DHCP) Type: to automatically obtain an IP address on the LAN/private network. Device Name: Enter the Device Name of the AP. Changing the Device Name is recommended if there is more than one D-Link device within the subnet.
Section 3 - Configuration Network Setup - Static IP Select Static IP to manually enter the IP address, subnet mask, and default gateway addresses. LAN Connection Select Static IP from the drop-down menu. Type: IP Address: Enter the IP address of the access point. The default IP address is 192.168.0.1. If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to return to the configuration utility. Subnet Mask: Enter the Subnet Mask.
Section 3 - Configuration My IPv6 Select Link-local only from the drop-down menu. Connection is: LAN IPv6 Address This section displays the IPv6 address of the router. settings: My IPv6 Select static IPv6 from the drop-down menu. Connection is: LAN IPv6 Enter the LAN (local) IPv6 address for the router.
Section 3 - Configuration My IPv6 Select Autoconfiguration (Stateless/DHCPv6) from the Connection: drop down menu. IPv6 DNS Select Obtain IPv6 DNS Server automatically or enter a Settings: specific DNS Server address.
Section 3 - Configuration Configuration PLC Settings - AP Mode This section will show you how to configure your new D-Link PowerLine AV using the web-based configuration utility.
Section 3 - Configuration Network You can set the name of your network and to make it Name: either public or private. Make sure the Network Name of all of the devices within your PowerLine network is the same. Public Select this option if you would like to make your Network powerline network public with the default Network Name: Name of “HomePlugAV”. Since this is a commonly used Network Name, it is less secure than a private Network Name.
Section 3 - Configuration Status: This field shows the status of the device. If the field displays the word Connect, then the device is connected to your PowerLine network. If the field displays the word Disconnect, then the device has been added to the network but it is not ready. Please check its password and make sure the device is powered on. QoS Setting: You can configure your PowerLine AV devices to give priority to powerline network traffic accordingly.
Section 3 - Configuration Network Filter Use MAC (Media Access Control) Filters to authorize wireless clients to access your network by their MAC addresses. When enabled, any client not on the MAC filter list will not be able to access your network. MAC Address Select Enable or Disable from the drop-down Filter: menu. MAC Address: Enter the MAC address you would like to filter. To find the MAC address on a computer, please refer to the Networking Basics section in this manual.
Section 3 - Configuration Advanced Wireless Transmit Sets the transmit power of the antennas. Power: Note: Transmit power is regulated by international standard. Users are forbidden to change its maximum limit. WLAN Select this checkbox to enable WLAN partition. If this Partition: feature is enabled, then there is no barrier between communication among wireless stations connecting to the Access Point. If this is disabled, wireless clients are not allowed to exchange data through the Access Point.
Section 3 - Configuration Wi-Fi Protect Setup Wi-Fi Protect Enables the Wi-Fi Protected Setup feature. Setup: Reset to Restores the default Wi-Fi setup. Unconfigure: Current PIN: Shows the current value of the access point’s PIN. Generate New Create a random number that is a valid PIN: PIN. This becomes the access point’s PIN. You can then copy this PIN to the user interface of the user. Reset PIN to Restores the default PIN of the access Default: point.
Section 3 - Configuration Add Wireless Device with WPS Adding a Wireless Device Using the PIN Method Please select one of the following configuration methods and click Next to continue.
Section 3 - Configuration Adding a Wireless Device Using the PBC Method Select PBC to use Push Button Configuration in order to connect to your network. Click Connect to continue. Press the WPS Button on the wireless device that you are adding to your network to complete the setup.
Section 3 - Configuration User Limit Settings In this section, you may set a limit to the number of wireless clients to prevent heavy wireless traffic.
Section 3 - Configuration Admin This page will allow you to change the Administrator password. The administrator password has read/write access. Password: Enter a new password for the Admin User Name. The administrator account can change the configuration of the device. Verify Enter the same password that you entered in Password: the previous textbox in order to confirm its accuracy. System Name: Enter DHP-1320.
Section 3 - Configuration Time This page will allow you to change the Administrator password. The administrator password has read/write access. Time Zone: Select the Time Zone from the drop-down menu. Daylight To select Daylight Saving time manually, select Saving: enabled or disabled, and enter a start date and an end date for daylight saving time. Enable NTP NTP is short for Network Time Protocol. NTP Server: synchronizes computer clock times in a network of computers. Check this box to use a NTP server.
Section 3 - Configuration System Settings Save Settings to Use this option to save the current router configuration Local Hard Drive: settings to a file on the hard disk of the computer you are using. First, click the Save button. You will then see a file dialog, where you can select a location and file name for the settings. Load Settings Use this option to load previously saved router from Local Hard configuration settings.
Section 3 - Configuration Firmware You can upgrade the firmware of the access point from this page. Make sure the firmware you would like to use is on the local hard drive of your computer. Click Browse... to locate the firmware file to be used for the update. Please check the D-Link support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site.
Section 3 - Configuration Schedules Schedules can be created for use with enforcing rules. For example, if you would like to restrict web access to Mon-Fri from 3:00 p.m. to 8:00 p.m., you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a StartTime of 3:00 p.m. and End Time of 8:00 p.m. Name: Enter a name for your new schedule. Days: Select a day, a range of days, or All Week to include every day. Time: Check All Days or enter a start and end time for your schedule.
Section 3 - Configuration Device Info This page displays the current information for the DHP-W306AV. It will display the LAN and wireless LAN information. General: Displays the access point’s time and firmware version. LAN: Displays the MAC address and the private (local) IP settings for the access point. Wireless LAN: Displays the wireless MAC address and your wireless settings such as SSID and Channel.
Section 3 - Configuration Logs The DHP-W306AV keeps a running log of events and activities occurring on the AP. If the AP is rebooted, the logs are automatically cleared. You can save the log files under Log Settings. Log Options: You can select the types of messages that you would like to display from the log: System Activity, Debug Information, Attacks, Dropped Packets, and Notice. Select the types you want to view and click Apply Log Settings Now.
Section 3 - Configuration Statistics The DHP-1360 keeps statistics of the traffic that passes through it. You can view the amount of packets that pass through the LAN and wireless portions of the network. The traffic counter will reset if the access point is rebooted. Refresh Statistics: Click the Refresh button to refresh the Access Point’s traffic statistics.
Section 3 - Configuration Wireless This section allows you to view the wireless clients that are connected to your wireless access point.
Section 3 - Configuration IPv6 This section will display all of your IPv6 Internet and network connection details.
Section 3 - Configuration Support D-Link DHP-1320 User Manual 135
Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DHP-1320 offers the following types of security: • WPA2 (Wi-Fi Protected Access 2) • WPA2-PSK (Pre-Shared Key) • WPA (Wi-Fi Protected Access) • WPA-PSK (Pre-Shared Key) What is WPA? WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
Section 4 - Security Configure WEP It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2. Click on Setup and then click Wireless Settings on the left side. 3.
Section 4 - Security Configure WPA/WPA2-Personal (PSK) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2. Click on Setup and then click Wireless Settings on the left side. 3.
Section 4 - Security Configure WPA/WPA2-Enterprise (RADIUS) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2. Click on Setup and then click Wireless Settings on the left side. 3.
Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows® 7 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). Wireless Icon 2. The utility will display any available wireless networks in your area.
Section 5 - Connecting to a Wireless Network 3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. 4. The following window appears while your computer tries to connect to the router.
Section 5 - Connecting to a Wireless Network 5. Enter the same security key or passphrase that is on your router and click Connect. You can also connect by pushing the WPS button on the router. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 5 - Connecting to a Wireless Network Configure WPS The WPS feature of the router can be configured using Windows® 7. Carry out the following steps to use Windows® 7 to configure the WPS feature of the router: 1. Click the Start button and select Computer from the Start menu. 2. Click the Network option.
Section 5 - Connecting to a Wireless Network 3. Double-click the DHP-1320. 4. Input the WPS PIN number (displayed in the WPS window on the Router’s LCD screen or in the Setup > Wireless Setup menu in the Router’s Web UI) and click Next.
Section 5 - Connecting to a Wireless Network 5. Type a name to identify the network. 6. To configure advanced settings, click the icon. Click Next to continue.
Section 5 - Connecting to a Wireless Network 7. The following window appears while the Router is being configured. Wait for the configuration to complete. 8. The following window informs you that WPS on the DHP-1320 has been setup successfully. Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future. 9. Click Close to complete WPS setup.
Section 5 - Connecting to a Wireless Network Using Windows Vista® Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista® utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility.
Section 5 - Connecting to a Wireless Network Configure Wireless Security It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network. 2.
Section 5 - Connecting to a Wireless Network 3. Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 5 - Connecting to a Wireless Network Using Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
