Section 1 - Product Overview Product PackageOverview Contents DHP-1320 Wireless N PowerLine Router Two Detachable Antennas Ethernet Cable Power Adapter CD-ROM with Manual and Setup Wizard Note: Using a power supply with a different voltage rating than the one included with the DHP-1320 will cause damage and void the warranty for this product.
Section 1 - Product Overview System Requirements Network Requirements • An Ethernet-based Cable or DSL modem • IEEE 802.11n or 802.11g wireless clients • 10/100 Ethernet Computer with the following: • Windows®, Macintosh, or Linux-based operating system • An installed Ethernet adapter Web-based Configuration Utility Requirements Browser Requirements: • Internet Explorer 6 or higher • Firefox 3.0 or higher • Safari 3.0 or higher • Chrome 2.
Section 1 - Product Overview Introduction TOTAL PERFORMANCE Combines award winning router features and IEEE 802.11n/g wireless technology to provide the best wireless performance. TOTAL SECURITY The most complete set of security features including Active Firewall and WPA/WPA2 to protect your network against outside intruders. TOTAL COVERAGE Provides greater wireless signal rates even at farther distances for best-in-class Whole Home Coverage.
Section 1 - Product Overview Features • Faster Wireless Networking - The DHP-1320 provides up to 300Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. The performance of this 802.11n wireless router gives you the freedom of wireless networking at speeds 650% faster than 802.11g. • Compatible with 802.
Section 1 - Product Overview Hardware Overview Connections 1 1 2 3 4 5 6 7 AP-Router Switch Two-way switch used to Select AP or Router Mode. 2 LAN Ports (1-3) 3 Internet Port The auto MDI/MDIX Internet port is the connection for the Ethernet cable to the cable or DSL modem. 4 Reset Button Pressing the Reset button restores the router to its original factory default settings.
Section 1 - Product Overview Hardware Overview WPS Button 1 2 1 WPS Button Press the WPS button for one second to initiate the WPS process. The button will flash blue while a WPS connection is being established. The button will light solid blue for 5 seconds when the device has successfully been added to the network. 2 ENY Button Push this button to establish a secure PowerLine network with other PowerLine AV devices.
Section 1 - Product Overview Hardware Overview LEDs 1 2 3 4 5 6 1 Power LED A solid green light indicates a proper connection to the power supply. This LED will light orange during a factory reset or reboot. A slow blinking orange LED indicates that the Router has crashed during bootup. 2 Internet LED A solid green light indicates that the internet connection has successfully completed. This LED blinks green during data transmission.
Section 2 - Installation Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage. Before you Begin • Please configure the router with the computer that was last connected directly to your modem. • You can only use the Ethernet port on your modem.
Section 2 - Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Section 2 - Installation Hardware Installation - For Router Mode 1 LAN 2 INTERNET RESET USB ON/OFF AC IN 3 AR RT Start Here Windows users can use the Quick Router Setup Wizard (from the CD) to configure their router. If you do not want to use the wizard, lost your CD, or are running Mac or Linux, you will need to use the manual setup procedure below. Quick Router Setup Wizard For the Wizard to work, the computer must be connected to the Internet and be online.
Section 2 - Installation Connect to Cable/DSL/Satellite Modem If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below: 1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Unplug the modem’s power adapter. 3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the Internet port on the router. 4. Plug an Ethernet cable into one of the three LAN ports on the router.
Section 2 - Installation Connect to Another Router If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network: • Disable UPnP™ • Disable DHCP • Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address from your other router. To connect to another router, please follow the steps below: 1.
Section 2 - Installation 6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the Internet (WAN) port of the D-Link router. 8. You may now use the other 2 LAN ports to connect other Ethernet devices and computers. To configure your wireless network, open a web browser and enter the IP address you assigned to the router.
Section 2 - Installation Hardware Installation - For Access Point Mode Room 1 Room 2 DHP-306AV Wireless Router Modem RESET 1 2 1 LAN 2 LAN 3 4 INTERNET INTERNET RESET USB ON/OFF USB INTERNET 5V - - - 3A AC IN 3 AR RT DHP-306AV Wireless N PowerLine Router (AP Mode) Room3 Step 1 Move the switch on the back of the DHP-1320 to “AP”. Connect the supplied power cord into the power receptor located on the back of the DHP1320 and plug into a power outlet as illustrated in Room 3.
Section 1 - Product Overview PowerLine Installation Considerations Plan the location of your PowerLine devices: 1. Connect the PowerLine devices to electrial outlets that are not controlled by a wall switch in order to avoid accidentally turning off the power to the device. 2. Do not connect the Wireless N PowerLine Router to an extension cord, surge protector, or power strip. This might prevent the device from working correctly or it may reduce the network performance. 3.
Section 1 - Product Overview PowerLine Security It is strongly recommended to encrypt your PowerLine network. By encrypting the data that is sent via your PowerLine adapters, you will prevent nearby hackers with a Powerline adapter to connect to your network and steal your information. To encrypt your PowerLine network, follow the steps below: PowerLine Network-Quick Setup Encryption Button Usage The ENY Button is used to add a PowerLine AV device to a PowerLine network.
Section 1 - Product Overview Configuring a PowerLine Network Connecting two PowerLine AV devices for the first time To initially connect the DHP-1320 AV to another PowerLine AV device and create a network: 1. Plug the DHP-1320 into a power outlet. Press the ENY button for 1 to 3 seconds. The PowerLine AV LED should start to blink. 2. Plug the other PowerLine device (e.g. the DHP-W306AV) into a power outlet. Press the ENY button on this PowerLine device for 1 to 3 seconds. 3.
Section 1 - Product Overview Connecting a PowerLine AV device to an existing PowerLine network To add a DHP-1320 if you already have an existing network with 2 more PowerLine devices: 1. Press the ENY button on the DHP-1320 for more than 10 seconds to make sure it is not connected to any other PowerLine network. 2. Press the ENY button of any device already in your PowerLine network (e.g. the DHP-306AV) for 1 to 3 seconds. The ENY LED should start to blink. 3.
Section 2 - Installation Getting Started The DHP-1320 includes a Quick Router Setup Wizard CD. Follow the simple steps below to run the Setup Wizard to guide you quickly through the installation process. Insert the Quick Router Setup Wizard CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows® XP. The steps and screens are similar for the other Windows operating systems. If the CD Autorun function does not automatically start on your computer, go to Start > Run.
Section 3 - Configuration Configuration (Router Mode) This section will show you how to configure your new D-Link wireless router using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1). Select Admin in the User Name field. Leave the password blank by default.
Section 3 - Configuration Setup Internet This section allows you to configure your Router’s Internet settings. Internet The Internet Connection Setup Wizard provides a quick Connection method for configuring your Internet settings. To start Setup Wizard: the Internet Connection Setup Wizard, click the Internet Connection Setup Wizard button. Refer to “Internet Connection Setup Wizard” on page 22 for more information on how to use the Internet Connection Setup Wizard.
Section 3 - Configuration Internet Connection Setup Wizard Click the Internet Connection Setup Wizard button to start the Internet Connection Setup Wizard.
Section 3 - Configuration The following window appears, summarizing the steps required to complete the Internet Connection Setup Wizard: Click Next to continue. Create a new password and then click Next to continue. Select your time zone from the drop-down menu and then click Next to continue.
Section 3 - Configuration Select the type of Internet connection you use and then click Next to continue. If you selected DHCP Connection (Dynamic IP Address), you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click Clone Your PC’s MAC Address and then click Next to continue. The Host Name is optional but may be required by some ISPs. The default host name is the device name of the router and may be changed.
Section 3 - Configuration If you selected PPPoE, enter your PPPoE username and password. If your ISP requires you to enter a PPPoE service name, enter the service name in the Service Name field. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. Click Next to continue. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
Section 3 - Configuration If you selected L2TP, enter your L2TP username and password. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and L2TP server addresses. Click Next to continue. If you selected Static, enter your network settings supplied by your Internet provider. Click Next to continue.
Section 3 - Configuration Click Connect to save your settings. The following window appears to indicate that the settings are being saved. When the Router has finished saving all the changes, the Setup> Internet window will open. Close your browser window and reopen it to test your Internet connection. It may take a few tries to initially connect to the Internet.
Section 3 - Configuration Manual Internet Connection Setup Internet Use the My Internet Connection is drop-down menu to Connection select the mode that the router should use to connect to Type: the Internet. Advanced Advanced Domain Name System (DNS) Services enhances DNS Service: your Internet performance by getting you the information and web pages you are looking for faster and more reliably.
Section 3 - Configuration Manual Internet Connection Setup Static IP Select Static IP from the drop-down menu if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
Section 3 - Configuration Manual Internet Connection Setup Dynamic IP (DHCP) Select Dynamic IP (DHCP) from the drop-down menu to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for cable modem services such as Comcast and Cox. Host Name: The Host Name is optional but may be required by some ISPs. Leave blank if you are not sure.
Section 3 - Configuration Manual Internet Connection Setup PPPoE (Username/Password) Select PPPoE (Username/Password) from the drop-down menu if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
Section 3 - Configuration MAC Address: The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card. Click the Save Settings button to save any changes made.
Section 3 - Configuration Manual Internet Connection Setup PPTP Select PPTP (Point-to-Point Tunneling Protocol) from the drop-down menu if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Address Mode: Select Static IP if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic IP. PPTP IP Address: Enter the IP address (Static PPTP only).
Section 3 - Configuration MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU. MAC Address: The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP.
Section 3 - Configuration Manual Internet Connection Setup L2TP Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. L2TP IP Address: Enter the L2TP IP address supplied by your ISP (Static only).
Section 3 - Configuration MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU. MAC Address: The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP.
Section 3 - Configuration Wireless Settings If you want to configure the wireless settings on your router using the wizard, click Wireless Connection Setup Wizard and refer to “Wireless Connection Setup Wizard” on page 103. Click Add Wireless Device with WPS if you want to add a wireless device using Wi-Fi Protected Setup (WPS) and refer to “Add Wireless Device with WPS Wizard” on page 106.
Section 3 - Configuration Manual Wireless Settings 802.11n/b/g (2.4GHz) Enable Wireless: Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Schedule: Select the time frame that you would like your wireless network enabled. The schedule may be set to Always. Any schedule you create will be available in the drop-down menu. Click New Schedule to create a new schedule.
Section 3 - Configuration Channel Width: Select the Channel Width: Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices. 20MHz - Select if you are not using any 802.11n wireless clients. This is the default setting. Wireless Security Refer to “Wireless Security” on page 136 for more information regarding wireless security. Mode: Click the Save Settings button to save any changes made.
Section 3 - Configuration Network Settings This section will allow you to change the local network settings of the router and to configure the DHCP settings. Router Use this section to configure the Router’s local network Settings: settings. DHCP Server Use this section to configure the DHP-1320’s built-in DHCP Settings: server settings. Add DHCP Use this section to create a new DHCP reservation or Reservation: manage existing DHCP reservations.
Section 3 - Configuration Network Settings Router Settings Router IP Address: Enter the IP address of the router. The default IP address is 192.168.0.1. If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the configuration utility. Default Subnet Enter the Subnet Mask. The default subnet mask is Mask: 255.255.255.0. Device Name: Enter a Host Name to identify the DHP-1320. Local Domain: Enter the Domain name (Optional).
Section 3 - Configuration Network Settings DHCP Server Settings DHCP stands for Dynamic Host Control Protocol. The DHP-1320 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DHP-1320.
Section 3 - Configuration Network Settings DHCP Reservation If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range. Enable: Check this box to enable the reservation. Computer Enter the computer name.
Section 3 - Configuration USB Settings In this section you may configure your USB port. You can select several configurations to choose from such as Share Port and WCN Configuration.
Section 3 - Configuration PLC Settings (Router Mode) This section will show you how to configure your new D-Link PowerLine AV using the web-based configuration utility.
Section 3 - Configuration Network You can set the name of your network and to make it Name: either public or private. Make sure the Network Name of all of the devices within your PowerLine network is the same. Public Select this option if you would like to make your powerline Network network public with the default Network Name of Name: “HomePlugAV”. Since this is a commonly used Network Name, it is less secure than a private Network Name.
Section 3 - Configuration Member List: This section provides information on the PowerLine AV devices in your PowerLine network, or any devices that were previously connected but it are currently disconnected. Link Rate: Displays the device’s current data rate in Mbps. Status: This field shows the status of the device. If the field displays the word Connect, then the device is connected to your PowerLine network.
Section 3 - Configuration Advanced Virtual Server The DHP-1320 can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DHP-1320 firewall feature filters out unrecognized packets to protect your LAN network so all computers networked with the DHP-1320 are invisible to the outside world.
Section 3 - Configuration The Virtual Server window allows you to open a single port. If you would like to open a range of ports, refer to the next page. Enable Check the box on the left side to enable the Virtual Checkbox: Server rule. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Configuration Port Forwarding This will allow you to open a single port or a range of ports. Enable Checkbox: Tick the checkbox on the left side to enable the Port Forwarding rule. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Configuration Application Rules Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DHP1320.
Section 3 - Configuration QoS Engine The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classified automatically. Enable Traffic This option is disabled by default. Enable this option Shapping: for better performance and experience with online games and other interactive applications, such as VoIP.
Section 3 - Configuration Network Filter Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the Broadband Router.
Section 3 - Configuration Access Control The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to only grant access to approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games. Add Policy: Check the Enable Access Control check box and click the Add Policy button to start the Access Control Wizard. Access Control Wizard Click Next to continue with the wizard.
Section 3 - Configuration Enter a name for the policy and then click Next to continue. Select a schedule (I.E. Always) from the drop-down menu and then click Next to continue. Enter the following information and then click Next to continue. • Address Type - Select IP address, MAC address, or Other Machines. • IP Address - Enter the IP address of the computer you want to apply the rule to.
Section 3 - Configuration Select the filtering method and then click Next to continue. Enter the rule: Enable - Check to enable the rule. Name - Enter a name for your rule. Dest IP Start - Enter the starting IP address. Dest IP End - Enter the ending IP address. Protocol - Select the protocol. Dest Port Start - Enter the starting port number. Dest Port End - Enter the ending port number. To enable web logging, click Enable. Click Save to save the access control rule.
Section 3 - Configuration Website Filter Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network. To use this feature select the appropriate Web Filtering option, enter the domain or website, and click Save Settings. Configure Web Select ALLOW computers access to ONLY these sites, or Filtering: DENY computers access to ONLY these sites from the drop-down menu. Website URL: Enter the keywords or URLs that you want to allow or block.
Section 3 - Configuration Inbound Filter The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can configure inbound data filtering rules that control data based on an IP address range. Inbound Filters can be used with Virtual Server, Port Forwarding, or Remote Administration features. Name: Enter a name for the inbound filter rule. Action: Select Allow or Deny. Enable: Check to enable rule. Remote IP Enter the starting IP address. Enter 0.0.
Section 3 - Configuration Firewall Settings A firewall protects your network from the outside world. The DHP-1320 offers a firewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
Section 3 - Configuration DMZ Host: If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer. Carry out the following to create a DMZ host: 1. Check the Enable DMZ box. 2. Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication in the DMZ IP address field.
Section 3 - Configuration Routing The Routing option is an advanced method of customizing specific routes of data through your network. Routing List: Each Route has a checkbox next to it, check the box of the route you wish to enable. Name: Specify a name for identification of this route. Interface: Select the interface which the IP packet must use to transit out of the router when this route is used. Destination IP: Enter the address of the host or network you wish to access.
Section 3 - Configuration Advanced Wireless Settings 802.11n/b/g (2.4GHz) Transmit Power: Set the transmit power of the antennas. Beacon Period: Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. RTS Threshold: This value should remain at its default setting of 2346. If inconsistent data flow is a problem, only a minor modification should be made.
Section 3 - Configuration Wi-Fi Protected Setup (WPS) Wi-Fi Protected Setup (WPS) System is a simplified method for securing your wireless network during the “Initial setup” as well as the “Add New Device” processes. The Wi-Fi Alliance (WFA) has certified it across different products as well as manufactures. The process is just as easy, as depressing a button for the Push-Button Method or correctly entering the 8-digit code for the Pin-Code Method.
Section 3 - Configuration Add Wireless Click the Add Wireless Device with WPS button to start Wireless Connection Setup Wizard. This wizard helps you add wireless Station: devices to the wireless network. The wizard will either display the wireless network settings to guide you through manual configuration, prompt you to enter the PIN for the device, or ask you to press the configuration button on the device.
Section 3 - Configuration Advanced Network Enable UPnP: To use the Universal Plug and Play (UPnP™) feature click on Enabled. UPNP provides compatibility with networking equipment, software and peripherals. Enable WAN Ping Unchecking the box will not allow the DHP-1320 to Response: respond to pings. Blocking the Ping may provide some extra security from hackers. Check the box to allow the Internet port to be “pinged”.
Section 3 - Configuration IPv6 Use the IPv6 window to configure the mode that the Router will use to access an IPv6 Internet connection. My IPv6 Use the drop-down menu to select the IPv6 Connection is: Internet Connection mode.
Section 3 - Configuration IPv6 Static IPv6 Select Static IPv6 from the My IPv6 Connection is drop-down menu if your Router will use a static IPv6 address to connect to the Internet. WAN IPv6 Address Enter the address settings supplied by your Internet Settings: provider (ISP). LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN Address Use this section to configure the IPv6 autoconfiguration Autoconfiguration settings.
Section 3 - Configuration IPv6 Static IPv6 - Stateless To configure the Router to use a Static IPv6 Stateless connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable automatic Check to enable the Autoconfiguration feature. IPV6 address assignment: Autoconfiguration Select the Stateless option from the drop-down menu. Type: Router Enter the Router Advertisement Lifetime (in minutes).
Section 3 - Configuration IPv6 Static IPv6 - Stateful To configure the Router to use a Static IPv6 Stateful connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Select the Stateful(DHCPv6) option from the drop-down Type: menu. IPv6 Address Range Enter the start IPv6 Address for the DHCPv6 range for your Start: local computers.
Section 3 - Configuration IPv6 Autoconfiguration (Stateless/DHCPv6) Select Static IPv6 from the My IPv6 Connection is drop-down menu if your Router will use a static IPv6 address to connect to the Internet. IPv6 DNS Settings: Select Obtain DNS Server address automatically or enter a specific DNS server address. LAN IPv6 Address Enter the LAN (local) IPv6 address for the router. Settings: LAN IPv6 Displays the Router’s LAN Link-Local Address.
Section 3 - Configuration IPv6 Autoconfiguration (Stateless/DHCPv6) - Stateless To configure the Router to use a Static IPv6 Stateless connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable automatic Check to enable the Autoconfiguration feature. IPv6 address assignment: Autoconfiguration Select the Stateless option from the drop-down menu. Type: Router Enter the Router Advertisement Lifetime (in minutes).
Section 3 - Configuration IPv6 Autoconfiguration (Stateless/DHCPv6) - Stateful To configure the Router to use a Static IPv6 Stateful connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable automatic Check to enable the Autoconfiguration feature. IPv6 address assignment: Autoconfiguration Select the Stateful(DHCPv6) option from the drop-down Type: menu.
Section 3 - Configuration IPv6 6to4 Select 6to4 from the My IPv6 Connection is drop-down menu if your Router will use a 6 to 4 tunnel to connect to the Internet. Primary DNS Enter the DNS Address supplied by your Internet provider Address: (ISP). LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. Click the Save Settings button to save any changes made.
Section 3 - Configuration IPv6 6to4 - Stateless To configure the Router to use an IPv6 to IPv4 tunnel stateless autoconfiguration connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable automatic Check to enable the Autoconfiguration feature. IPv6 address assignment: Autoconfiguration Select the Stateless option from the drop-down menu. Type: Router Enter the Router Advertisement Lifetime (in minutes).
Section 3 - Configuration IPv6 6to4 - Stateful To configure the Router to use an IPv6 to IPv4 tunnel stateful autoconfiguration connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable automatic Check to enable the Autoconfiguration feature. IPv6 address assignment: Autoconfiguration Select the Stateful option from the drop-down menu. Type: IPv6 Address Enter the start IPv6 Address for the DHCPv6 range for Range Start: your local computers.
Section 3 - Configuration IPv6 6rd My IPv6 Select 6rd from the drop-down menu. Connection: 6rd IPv6 Prefix: Enter the settings supplied by your Internet provider (ISP). LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router.
Section 3 - Configuration IPv6 6rd (Stateless) Enable automatic Check to enable the Autoconfiguration feature. IPv6 address assignment: Autoconfiguration Select the Stateless option from the drop-down menu. Type: Router Enter the Router Advertisement Lifetime (in minutes). Advertisement Lifetime: Click the Save Settings button to save any changes made.
Section 3 - Configuration IPv6 6rd (Stateful) Enable automatic Check to enable the Autoconfiguration feature. IPv6 address assignment: Autoconfiguration Select the Stateful DCHPv6 option from the drop-down Type: menu. IPv6 Address Enter the start IPv6 Address for the DHCPv6 range for Range Start: your local computers. IPv6 Address Enter the end IPv6 Address for the DHCPv6 range for Range End: your local computers. IPv6 Address Enter the IPv6 Address Lifetime (in minutes).
Section 3 - Configuration IPv6 IPv6 over IPv4 Tunnel My IPv6 Select IPv6 over IPv4 Tunnel from the drop-down Connection: menu. IPv6 over IPv4 Enter the IPv6 settings supplied by your Tunnel Broker. Tunnel Settings: IPv6 DNS Settings: Obtain a DNS server address automatically or enter a specific DNS server address. Primary/Secondary Enter the primary and secondary DNS server addresses. DNS Address: LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router.
Section 3 - Configuration IPv6 IPv6 over IPv4 Tunnel - Stateless Enable automatic Check to enable the IPv6 address assignment IPv6 address feature. assignment: Autoconfiguration Select Stateless. Refer to the previous page for Type: Stateful. Router Enter the Router Advertisement Lifetime (in Advertisement minutes).
