Version 1.
Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision 1.0 Date March 08, 2013 Description • Second release version Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
Table of Contents Table of Contents Preface...........................................................................................i Manual Revisions............................................................................ i Trademarks....................................................................................... i Product Overview.......................................................................1 Package Contents..........................................................................
Table of Contents Wireless Security...................................................................... 49 What is WPA?.................................................................................49 Configure WPA-Personal (PSK)................................................50 Connect to a Wireless Network............................................. 51 Using Windows® 7........................................................................51 Using Windows® XP.........................................
Section 1 - Product Overview Product PackageOverview Contents • D-Link GO-RT-N150 • Power Adapter • Ethernet Cable Note: Using a power supply with a different voltage rating than the one included with the D-Link GO-RT-N150 will cause damage and void the warranty for this product. Note: Always attach the power cord plug to the power supply before inserting the power cord and connected power supply to the wall outlet.
Section 1 - Product Overview System Requirements Network Requirements • An Ethernet-based Cable or DSL modem • IEEE 802.11n/g wireless clients • 10/100 Ethernet Computer with the following: • Windows®, Macintosh, or Linux-based operating system • An installed Ethernet adapter Web-based Configuration Utility Requirements Browser Requirements: • Internet Explorer 6.0 or higher • Mozilla 1.7.12 or higher • Firefox 1.5 or higher • Safari 1.0 or higher (with Java 1.3.1 or higher) • Flock 0.7.
Section 1 - Product Overview Features • Faster Wireless Networking - The D-Link GO-RT-N150 provides up to 150Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. • Compatible with 802.11g Devices - The D-Link GO-RT-N150 is still fully compatible with the IEEE 802.11g standard, so it can connect with existing 802.11g PCI, USB and Cardbus adapters.
Section 1 - Product Overview Hardware Overview Connections Power Receptor Receptor for the supplied power adapter. Internet Port The auto MDI/MDIX Internet port is the connection for the Ethernet cable to the cable or DSL modem. WPS Button Pressing the WPS button allows you to establish a secure connection with a new device. LAN Ports (1-4) Connect Ethernet devices such as computers, switches, and hubs.
Section 1 - Product Overview Hardware Overview LEDs Power LED A solid light indicates a proper connection to the power supply. Internet LED A solid light indicates connection on the Internet port.
Section 2 - Installation Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet or cabinet, or in the attic or garage. Before you Begin • Please configure the router with the computer that was last directly connected to your modem. • You can only use the Ethernet port on your modem.
Section 2 - Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Section 2 - Installation Connect to Cable/DSL/Satellite Modem If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below: 1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down your computer. 3.
Section 2 - Installation Connect to Another Router If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network: • Disable UPnP • Disable DHCP • Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address from your other router. To connect to another router, please follow the steps below: 1.
Section 2 - Installation 6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7. Connect an Ethernet cable to one of the LAN ports on the router and connect it to your other router. Do not plug anything into the Internet port of the D-Link router. 8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers. To configure your wireless network, open a web browser and enter the IP address you assigned to the router.
Section 3 - Configuration Configuration This section will show you how to configure your D-Link wireless router using the web-based configuration utility. Setup To access the Easy Setup Wizard or configuration utility, open a web browser such as Internet Explorer and enter the IP address of the router (http://192.168.0.1).
Section 3 - Configuration Easy Setup Wizard Once logged into the web interface of the router, the Easy Setup Wizard will appear and perform WAN auto detection to obtain the type of Internet connection you are using.
Section 3 - Configuration According to the detection result, the wizard will indicate the type of Internet connection that you are currently using. To configure your wireless network, click Configure in Wireless Settings. Select the type of Wireless security you use (Disable Wireless Security or AUTO-WPA/WPA2) and enter the network name (SSID, Service Set Identifier) and security password. The network name (SSID) is the name of your wireless network. Create a name using up to 32 characters.
Section 3 - Configuration In the final stage of the Easy setup wizard, the summary will show your current configuration. Click Save to complete the setup. When the internet connectivity is established, the webpage will be redirected to the D-Link Website.
Section 3 - Configuration Internet Configuration Dynamic (Cable) If you opt to set up your Internet connection manually, you will be redirected to a WAN page that allows you to select the type of your Internet connection and enter the correct configuration parameters. Select your Internet connection type using the “My Internet Connection is” drop-down menu. Click Save Settings when you have configured the connection.
Section 3 - Configuration Dynamic IP Address (DHCP) My Internet Select Dynamic IP (DHCP) to obtain IP Address Connection: information automatically from your ISP. Select this option if your ISP did not provide you with any IP numbers to use. This option is commonly used for cable modem services. Host Name: The Host Name is optional but may be required by some ISPs. DNS Enter the Primary DNS server IP address assigned Addresses: by your ISP.
Section 3 - Configuration PPPoE (DSL) Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure you remove any PPPoE software from your computer. The software is no longer needed and will not work through a router. My Internet Select PPPoE (Username/Password) from the Connection: drop-down menu.
Section 3 - Configuration MTU: Transmission Unit for optimal performance with MAC Address: your specific ISP (default MTU is 1492). The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
Section 3 - Configuration Static IP Address Choose Static IP Address if all Internet ports’ IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP format, which is four octets each separated by a dot (x.x.x.x). The router will not accept the IP address if it is not in this format.
Section 3 - Configuration Wireless Settings If you want to manually configure the wireless settings on your router click Manual Wireless Network Setup and refer to the next page.
Section 3 - Configuration Manual Wireless Network Setup Enable Check the box to enable the wireless function. If Wireless: you do not want to use wireless, uncheck the box to disable it. Click Add New to create your own time schedule to enable the wireless function. Wireless Service Set Identifier (SSID) is the name of your Network Name: wireless network. Create a name using up to 32 characters. The SSID is case-sensitive. 802.11 Mode: Select one of the following: 02.
Section 3 - Configuration Enable Hidden Enabling Hidden Mode is another way Wireless: to secure your network. With this option enabled, no wireless clients will be able to see your wireless network when they perform a scan to see what’s available. In order for your wireless devices to connect to your router, you will need to manually enter the Wireless Network Name on each device. Wireless Security: Refer to Section 4- Wireless security for more information regarding wireless security.
Section 3 - Configuration Network Settings This section will allow you to change the local network settings of the router and to configure the DHCP settings. IP Address: Enter the IP address of the router. The default IP address is 192.168.0.1. If you change the IP address, once you click Save Settings, you will need to enter the new IP address in your browser to get back into the configuration utility. Subnet Mask: Enter the Subnet Mask. The default subnet mask is 255.255.255.0.
Section 3 - Configuration DHCP Server Settings DHCP stands for Dynamic Host Control Protocol. The D-Link GO-RT-N150 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to Obtain an IP Address Automatically. When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the router.
Section 3 - Configuration DHCP Reservation If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range. Computer Name: Enter the computer name or select from the dropdown menu and click <<. IP Address: Enter the IP address you want to assign to the computer or device.
Section 3 - Configuration Advanced Virtual Server The D-Link GO-RT-N150 can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The D-Link GO-RT-N150 firewall feature filters out unrecognized packets to protect your LAN so all computers networked with the router are invisible to the outside world.
Section 3 - Configuration This will allow you to open a single port. If you would like to open a range of ports, refer to the next page. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Configuration Port Forwarding This will allow you to open a single port or a range of ports. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to. If your computer is receiving an IP address automatically from the router (DHCP) then it will be listed in the “Computer Name” drop-down menu.
Section 3 - Configuration Application Rules Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications helps some of these applications work with the router.
Section 3 - Configuration Traffic Control Use this section to configure D-Link’s Smart Traffic Control. The Traffic Control improves your online gaming experience by ensuring that your game traffic is prioritized over other network traffic, such as FTP or Web. Enable Traffic Select this function to control the access bandwidth Control: of computer in LAN. Auto Bandwidth All the computers in LAN will be distributed the Equal: bandwidth equally.
Section 3 - Configuration Network Filters Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the Network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the router. Configure MAC Select Turn MAC Filtering Off, allow MAC Filtering: addresses listed below, or deny MAC addresses listed below from the drop-down menu.
Section 3 - Configuration Website Filters Website Filters are used to allow you to set up a list of allowed Web sites that can be used by multiple users through the network. To use this feature select Allow or Deny, enter the domain or website and click Add, and then click Save Settings. You must also select Apply Web Filter under the Access Control section (page 40). Configure Website Filter Select Allow or Deny computers access to only Below: these sites.
Section 3 - Configuration Firewall Settings A firewall protects your network from the outside world. The D-Link GO-RT-N150 offers a firewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ (Demilitarized Zone). This option will completely expose the chosen computer to the outside world.
Section 3 - Configuration Advanced Wireless Settings Transmit Power: Set the transmit power of the antennas. WMM Enable: WMM is QoS (Quality of Service) for your wireless network. This will improve the quality of video and voice applications for your wireless clients. Short Guard Check this box to reduce the guard interval time, Interval: therefore increasing the data capacity. However, it is less reliable and may create higher data loss. HT20/40 Coexistence: Select Enable or Disable for this feature.
Section 3 - Configuration Wi-Fi Protected Setup Wi-Fi Protected Setup (WPS) System is a simplified method for securing your wireless network during the “Initial Setup” and “Add New Device” processes. The Wi-Fi Alliance (WFA) has certified it across different products and manufacturers. The process is as quick and easy as simply pushing a button (the Push-Button Method) or entering the correct 8-digit code (the Pin-Code Method). The most effective security setting, WPA2, is used automatically.
Section 3 - Configuration Connect Your The wizard will either display the wireless Wireless network settings to guide you through manual Device: configuration, prompt you to enter the PIN for the device, or ask you to press the configuration button on the device. If the device supports Wi-Fi Protected Setup and has a configuration button, you can add it to the network by pressing the configuration button on the device and then the on the router within 60 seconds.
Section 3 - Configuration Advanced Network Settings UPnP Settings: To use the Universal Plug and Play (UPnP) feature click Enable UPnP. UPnP provides compatibility with networking equipment, software and peripherals. Enable WAN Unchecking the box will not allow the router to Ping Response: respond to pings. Blocking the ping may provide some extra security from hackers. Check the box to allow the Internet port to be “pinged”.
Section 3 - Configuration Tools Administrator Settings This page will allow you to change the administrator and user passwords. You can also enable Remote Management. There are two accounts that can access the management interface through the web browser. The accounts are admin and user. Admin has read/write access while user has read-only access. User can only view the settings but cannot make any changes. Only the admin account has the ability to change both admin and user account passwords.
Section 3 - Configuration Time Settings The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to automatically adjust the time when needed. Time Zone: Select the Time Zone from the drop-down menu.
Section 3 - Configuration System Settings Save Settings Use this option to save the current router to Local Hard configuration settings to a file on the hard disk of Drive: the computer you are using. First, click the Save button. You will then see a file dialog, where you can select a location and file name for the settings. Load Settings Use this option to load previously saved router from Local Hard configuration settings. First, use the Browse control Drive: to find a saved configuration settings file.
Section 3 - Configuration Update Firmware You can upgrade the firmware of the router here. Make sure the firmware file you want to use is on the local hard drive of the computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support site at http:// support.dlink.com for firmware updates. You can download firmware upgrades to your hard drive from the D-Link support site. Firmware Information: Displays the current firmware version and date.
Section 3 - Configuration DDNS The DDNS feature allows you to host a server (web, FTP, game server, etc…) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet service providers assign dynamic (changing) IP addresses. Using a DDNS service provider, users can enter in your domain name to connect to your server no matter what your IP address is.
Section 3 - Configuration Status Device Information This page displays the current information for the router. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed.
Section 3 - Configuration Log The router automatically logs (records) events of possible interest in its internal memory. If there is not enough internal memory for all events, logs of older events are deleted while logs of the latest events are retained. The Logs option allows you to view the router logs. You can define what types of events you want to view and the level of the events to view.
Section 3 - Configuration Statistics The screen below displays the Traffic Statistics. Here you can view the amount of packets that pass through the router on both the Internet and the LAN ports. The traffic counter will reset if the device is rebooted.
Section 3 - Configuration Internet Sessions The Internet Sessions page displays the full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer. IP Address: The IP address and, where appropriate, port number of the local application. TCP Session: This shows the number of TCP packets being sent from the source IP address.
Section 3 - Configuration Wireless The wireless client table displays a list of currently connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients.
Section 3 - Configuration Support D-Link GO-RT-N150 User Manual 48
Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The D-Link GO-RT-N150 offers the following types of security: • WPA2 (Wi-Fi Protected Access 2) • WPA (Wi-Fi Protected Access) • WPA2-PSK(Pre-Shared Key) • WPA-PSK (Pre-Shared Key) What is WPA? WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
Section 4 - Security Configure WPA-Personal (PSK) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1).
Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows® 7 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). Wireless Icon 2. The utility will display any available wireless networks in your area.
Section 5 - Connecting to a Wireless Network 3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. 4. The following window appears while your computer tries to connect to the router.
Section 5 - Connecting to a Wireless Network 5. Enter the same security key or passphrase that is on your router and click Connect. You can also connect by pushing the WPS button on the router. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 5 - Connecting to a Wireless Network Using Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Section 5 - Connecting to a Wireless Network Configure WPA-PSK It is recommended to enable WEP on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WEP key being used. 1. O p e n t h e W i n d o w s ® X P W i r e l e s s U t i l i t y b y r i g h t clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the WPAPSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router.
Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the D-Link GO-RT-N150. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screen shots on your computer will look similar to the following examples.) 1.
Section 6 - Troubleshooting • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Section 6 - Troubleshooting 3. Why can’t I connect to certain sites or send and receive e-mails when connecting through my router? If you are having a problem sending or receiving e-mail, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (e.g. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to.
Section 6 - Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size.
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Appendix A - Wireless Basics Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network. How does wireless work? Wireless works similarly to how cordless phones work; through radio signals transmitting data from point A to point B.
Appendix A - Wireless Basics Who uses wireless? Wireless technology has become so popular in recent years that almost everyone is using it, whether it’s for home, office, or business, D-Link has a wireless solution for it. Home • Gives everyone at home broadband access • Surf the web, check e-mail, send instant messages, etc.
Appendix A - Wireless Basics Tips Here are a few things to keep in mind, when you install a wireless network. Centralize Your Router or Access Point Make sure you place the router/access point in a centralized location within your network for the best performance. Try to place the router/access point as high as possible in the room so the signal gets dispersed throughout your home. If you have a two-story home, you may need a repeater to boost the signal and extend the range.
Appendix A - Wireless Basics Wireless Modes There are two basic modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router. • Ad-Hoc – Directly connecting to another computer for peer-to-peer communication, using wireless network adapters on each computer such as two or more DWM-140 wireless network USB adapters. An Infrastructure network contains an access point or wireless router.
Appendix B - Networking Basics Networking Basics Check your IP address After you install your adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows Vista® users type in the Start Search box.) At the prompt, type ipconfig and press Enter.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router or you need to assign a static IP address, please follow the steps below: Step 1 Windows Vista® Windows® XP Windows® 2000 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. Click on Start > Control Panel > Network Connections. From the desktop, right-click My Network Places > Properties.
Appendix C - Technical Specifications Technical Specifications Standards • IEEE 802.11g • IEEE 802.11b • IEEE 802.3 • IEEE 802.3u Security • WPA-Personal • WPA2-Personal Wireless Signal Rates* • 150Mbps • 48Mbps • 54Mbps • 24Mbps • 36Mbps • 12Mbps • 18Mbps • 9Mbps • 11Mbps • 5.5Mbps • 6Mbps • 1Mbps • 2Mbps Frequency Range • 2.4GHz to 2.483GHz LEDs Storage Humidity • 5%-95% non-condensing Safety & Emissions • CE Dimensions • L = 5.83 inches • W = 4.45 inches • H = 1.
Appendix D - Safety Statements Safety Statements CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
