Hardware Installation Guide Product Model: DXS-3600 Series Layer 2/3 Managed 10GbE Switch Release: 1.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Information in this document is subject to change without notice. Reproduction of this document in any manner whatsoever, without the written permission of the D-Link Corporation, is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of the D-Link Corporation; Microsoft and Windows are registered trademarks of the Microsoft Corporation.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Intended Readers The DXS-3600 Series Hardware Installation Guide contains detailed information about the hardware specifications of a switch in this series. It also contains brief information on how to configure and manage a switch in this series. This manual is intended for advanced level users that are familiar with network management concepts and terminology.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Safety Cautions To greatly reduce the risk of physical injury, electrical shock, fire, and damage to equipment, observe the following precautions. Observe and follow service markings. • Do not attempt to service any product, except when it is explained in the system’s documentation. • Opening or removing covers that are marked with this ( ) symbol may expose the user to electrical shock.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide • 115V/60Hz is used mostly in North and South America as well as Far Eastern countries like as South Korea and Taiwan • 100V/50Hz is used mostly in Eastern Japan and 100V/60Hz in Western Japan • 230V/50Hz is used mostly in Europe, the Middle East, Africa and the Far East General Precautions for Rack-Mountable Products Please pay careful attention to the following precautions concerning rack stability and safety.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Table of Contents Intended Readers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Typographical Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Notes, Notices, and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Introduction Switch Description Package Contents Features Front Panel Components Rear Panel Description Side Panel Description Switch Description The DXS-3600 Series switch is a switch designed to meet the needs and requirements Data Center networks that require Top-of-Rack access switches and Enterprise/Campus aggregation switches, where low latency and high bandwidth capacity is essential.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide If any item is missing or damaged, please contact your local D-Link reseller for replacement. Features This switch is action packed with an abundance of networking features that span inside and outside of the traditional Layer 3 framework. The list below highlights the significant protocols and features supported by this switch.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide • • • Management Information Base (MIBs) for MIBII, Bridge MIB, SNMPv2 MIB, RMON MIB, RMONv2 MIB, Ether-like MIB, 802.3 MAU MIB, 802.1p MIB, IF MIB, RADIUS Authentication Client MIB, IGMPv3 MIB, RIPv2 MIB, IP Forwarding Table MIB (CIDR), IPv4 Multicast Routing MIB, PIM MIB for IPv4, RADIUS Accounting Client MIB, Ping MIB, Trace out MIB, OSPFv2 MIB, VRRP MIB, Private MIB, Entity MIB.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide LED Indicators Located on the front panel of the switch are LED indicators: Power1, Power2, MGMT, Console, Fan1, Fan2, Fan3, and SD. Additionally, the DXS-3600-32S also has a Seven segment stacking ID LED. For each SFP+ port there is a Link/ Act light.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide LED Description Link/Act LEDs This LED will light solid green when there is a secure connection to a 10Gbps Ethernet device at any of the ports. This LED will light solid orange when there is a secure connection to a 1Gbps Ethernet device at any of the ports. This LED will blink green when a 10Gbps port is active, or blink orange when a 1Gbps port is active. This LED will be off when there is no link or activity.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Power Supply Module Connect the one end of the AC power cord supplied to the AC power connector and the other end into a properly grounded electrical outlet. The switch will automatically adjust the power setting to adapt to any voltage supply in the range from 100~240VAC at 50~60Hz. In addition, an optional second power supply module can be plugged into the second power supply connector slot displayed above.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Installation Installation Guidelines Installing the Switch without a Rack Installing the Switch into a Rack Installing Transceivers into the Transceiver Ports Installing Power Modules into the Power Module Ports Installing Fan Modules into the Fan Module Ports Installation Guidelines This section will discuss the hardware installation guidelines that the user must follow in order to properly and safely install this switch into the appropri
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Make sure that there is proper heat dissipation from and adequate ventilation around the switch. Leave at least 10 cm (4 inches) of space at the front and rear of the switch for ventilation. Installing the Switch into a Rack This section is used to guide the user through installing the switch into a switch rack. The switch can be mounted in a standard 19"(1U) rack using the provided mounting brackets. Use the following diagram as a guide.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Make sure that there is adequate space around the Switch to allow for proper air flow, ventilation, and cooling. Installing Transceivers into the Transceiver Ports The switch is equipped with small form-factor pluggable plus (SFP+) ports that can be used to connect various other networking devices to this switch that do not support the standard copper wiring connection.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide NOTE: The Power Modules all support a specific air-flow direction. This air-flow direction must be the same as the Fan Module installed. By default the air-flow direction of the Power Module and Fan Module installed is front-to-back. Installing an AC Power Module Connect the one end of the AC power cord supplied to the AC power connector and the other end into a properly grounded electrical outlet.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Installing a DC Power Module This switch supports a unique dual power input feature. Connect the one end of the DC power cord supplied to a DC power source (-48VDC/5.2A), that will be activated when the AC power is not working. Please make sure that connection polarity (positive and negative) is correct before using this feature to avoid any damaged. Connect the power source to the DC plug before plugging it into the switch.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide If you are installing a DC-powered switch, you must ground the chassis before connecting the switch to the DC power source, following the following instructions: • Use a minimum of 18 AWG stranded copper wire for grounding. The wire should be long enough to reach from the installed switch to the facility ground point. • Torque screwdriver with a 1/4-inch flat blade.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Switch Connections Switch to an End Node Switch to another Switch Switch to a Server Switch to an End Node End node is a generic name for edge networking devices that will be connected to this switch. Typical examples of end nodes are Personal Computers (PCs), Notebooks, Access Points, Print Servers, VoIP Phones and more. Each end node will be outfitted with a 10/100/1000Mbps, RJ-45, networking port.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Figure 3-2 Connecting a Switch to another switch by means of SFP/SFP+ Switch to a Server When configuring a network, users will most likely have to add a server or two to this switch. Generally, any port on this switch can be used to connect to a server, as they all operate at a maximum speed of one 10Gbps.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Switch Management Management Options Connecting to the Console Port Connecting using SNMP Connecting using the Web User Interface Management Options This switch provides multiple access platforms that can be used to configure, manage and monitor networking features available on this switch. Currently there are three management platforms available and they are described below.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Set the terminal emulation software as follows: • Select the appropriate serial port (COM1 or COM2). • Set the data rate to 115200 baud. • Set the data format to 8 data bits, 1 stop bit, and no parity. • Set flow control to none. Figure 4-1 COM1 Properties - Port Settings • Under Properties, select VT100 for Emulation mode. • Select Terminal keys for Function, Arrow and Ctrl keys.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Boot Procedure V1.10.007 ------------------------------------------------------------------------------Power On Self Test ........................................ MAC Address H/W Version 100 % : B8-A3-86-12-02-B0 : B1 Please Wait, Loading V1.10.023 Runtime Image .............. UART init ................................................. Starting runtime image Device Discovery .......................................... Configuration init .
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide DXS-3600-32S>enable DXS-3600-32S#configure terminal DXS-3600-32S(config)#username NewUser password 12345 DXS-3600-32S(config)#username NewUser privilege 15 DXS-3600-32S(config)#line console DXS-3600-32S(config-line)#login local DXS-3600-32S(config-line)#end DXS-3600-32S# Figure 4-5 To create a user account 1 At the CLI command prompt, enter the command ‘enable’ to enter the Privileged EXEC Mode. Press Enter.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide An example to change the IP address of the Switch to ‘10.90.90.90’, using a subnet mask of ‘255.0.0.0’: DXS-3600-32S>enable DXS-3600-32S#configure terminal DXS-3600-32S(config)#interface vlan 1 DXS-3600-32S(config-if)#ip address 10.90.90.90 255.0.0.0 DXS-3600-32S(config-if)#end DXS-3600-32S# Figure 4-7 To change the IP address 1 At the CLI command prompt, enter the command ‘enable’ to enter the Privileged EXEC Mode. Press Enter.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide NOTE: For customers interested in D-View, D-Link Corporation's proprietary SNMP management software, go to http://dview.dlink.com.tw/ and download the software and manual. Managed devices that support SNMP include software (referred to as an agent), which runs locally on the device. A defined set of variables (managed objects) is maintained by the SNMP agent and used to manage the device.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide traps and sends them to the trap recipient (or network manager). Typical traps include trap messages for Authentication Failure, and Topology Change. Management Information Base (MIB) The Management Information Base (MIB) stores management and counter information. The switch uses the standard MIB-II Management Information Base module. Consequently, values for MIB objects can be retrieved from any SNMPbased network management software.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Enter the User name and Password and click OK to proceed. This will open the Web-based User Interface. The switch management features available in the Web-based manager are explained below. Areas of the User Interface After a successful connection to the Web User Interface has been made, the following page should be displayed. AREA 2 AREA 1 Figure 4-12 Main Web Manager window On this page we will find three main areas to observe.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Appendix A - Technical Specifications Product Specifications Switch Series DXS-3600-16S: 8-Port 10Gigabit SFP+, Expandable, Layer 2/3 switch. DXS-3600-32S: 24-Port 10Gigabit SFP+, Expandable, Layer 2/3 switch. Dimensions DXS-3600-16S: 440mm (W) x 506mm (D) x 44mm (H), 19-inch, 1U Rackmount size DXS-3600-32S: 440mm (W) x 506mm (D) x 44mm (H), 19-inch, 1U Rackmount size Weight DXS-3600-16S: 9.89kg (21.8lb) DXS-3600-32S: 9.84kg (21.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Port Specifications Console Port RJ-45 interface for out-of-band CLI configuration Copper Ports Compliant to following standards: (10/100/1000Mbps) • IEEE 802.3 compliance For DXS-3600-EM-8T and DXS-3600-EM-4XT • IEEE 802.3u compliance • IEEE 802.3ab compliance • Support Half/Full-Duplex operations • Auto-negotiation, Auto MDI/MDIX • IEEE 802.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Port Specifications SFP+ Direct Attached Cables (DAC): • Direct Attached Cables are cables with a built-in SFP+ transceivers at both ends.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide LED Indicators Location LED Color Status Description LED Per Port Link/Act/Speed Green Light on (Solid) When there is a secure connection (or link) to 1000Mbps Ethernet device at any of the ports. Light blinking When there is reception or transmission of data occurring at 1000Mbps. Light on (Solid) When there is a secure connection (or link) to 10/ 100Mbps Ethernet device at any of the ports.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Appendix B - Cables and Connectors Ethernet Cable When connecting the Switch to another switch, a bridge or hub, a normal cable is necessary. Please review these products for matching cable pin assignment. The following diagrams and tables show the standard RJ-45 receptacle/connector and their pin assignments.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Console Cable A console cable is used when a user want to connect to the console port, of the switch, to access the command line interface. The following diagrams and tables show the standard Console-to-RJ45 receptacle/connector and their pin assignments.
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Warranty 29
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide Technical Support 30
