DVG-7022S/7044S/7062 VoIP Gateway User’s Manual Version 1.
© 2008 D-Link Corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of D-Link Corporation/D-Link Systems Inc.; Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Contents 1. Introduction ........................................................................................................................................................ 1 1-1 Product Overview.................................................................................................................................... 1 1-2 Hardware Description ............................................................................................................................. 2 2.
. Configuring the Gateway through IVR........................................................................................................... 73 4-1 IVR (Interactive Voice Response)......................................................................................................... 73 4-2 IP Configuration Settings—Set the IP Configuration of the WAN Port ................................................. 75 5. Dialing Principles ........................................................................
DVG-7022S/7044S/7062 User’s Manual Produect Overview 1. Introduction 1-1 Product Overview The DVG-7022S/7044S/7062S VoIP Gateway carries both voice and facsimile over the IP network. It uses the industry standard SIP call control protocol so as to be compatible with free registration services or VoIP service providers’ systems. As a standard user agent, it is compatible with all common Soft Switches and SIP proxy servers.
DVG-7022S/7044S/7062 User’s Manual Hardware Description 1-2 Hardware Description Front Panel y Power Indicator: Green light indicates a normal power supply. y Run Indicator: Blinking green light indicates normal operation. y Alarm Indicator: When the system starts up, the red light will blink. This indicator will also light to indicate any abnormal gateway behavior. y Voice ports indicators: Indicate connection and activity on the port 1 – 4 / 1 – 8.
DVG-7022S/7044S/7062 User’s Manual Hardware Description Rear Panel DVG-7022S Model DVG-7044S Model DVG-7062S Model WARNING: DO NOT (1) connect the phone ports to each other (FXS to FXS) or (2) connect any phone port directly to a PSTN line (FXS to PSTN) or to an internal PBX line (FXS to PBX extension). Doing so may damage your VoIP gateway. To restore factory default settings (IP address, User’s Name, Password): (1) Disconnect the power plug. (2) Press and hold the reset button for 6 seconds.
DVG-7022S/7044S/7062 User’s Manual Network Interface 2. Installation and Applications 2-1 Network Interface - Gateway Assigned with a Public IP Address Gateway can be assigned with a Public IP Address. The gateway will have a Public IP address for Internet connection regardless of whether it is a static IP address, DHCP (using a Cable Modem), or PPPoE (Dialup / ADSL).
DVG-7022S/7044S/7062 User’s Manual Telephone Interface Description 2-2 Telephone Interface Description Example for DVG-7022S/7044S/7062S: DVG-7022S/7044S/7062S connecting directly to the Telephone Line of a PSTN Phone is FXS interface and Line is FXO interfaces; FXO can all be connected to a PSTN to serve as a bridge between the PSTN and other VoIP telephones. The system also allows a call to be made from a traditional telephone line to connect with a user behind the Gateway.
DVG-7022S/7044S/7062 User’s Manual Telephone Interface Description FXS FXO D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual Gateway Configuration-Web Browser 3. Gateway Configuration – Use Web Browser The VoIP gateway allows users to configure its settings using a web interface (Web UI). You can access the Configuration Menu by opening a web-browser (e.g., Internet Explorer or Netscape Navigator) and entering the factory default LAN IP address: 192.168.8.254. The IP address of the Web UI is same as the default LAN IP noted elsewhere in this user’s manual.
DVG-7022S/7044S/7062 User’s Manual Network Settings 3-1 Network Settings (WAN) The network settings are used to set the gateway’s communication ports, IP configurations, and Phone Book Manager IP settings. y y y Current WAN IP Address: The IP address of the WAN port. Listen Port UDP: It is not necessary to change the protocol of the communication port used by the gateway, unless it conflicts with ports used by another device in your network.
DVG-7022S/7044S/7062 User’s Manual Network Settings ADSL PPPoE Settings Select “PPPoE” and enter the Account Number, Password and Reenter Password to confirm. Then click the “Accept” button at the bottom of the screen. Save the settings, and then restart the system. The system will take about 49 seconds to restart. PPTP Settings Click PPTP and enter IP Address, Subnet mask, PPTP Server, PPTP ID and Password. Then click the Accept button at the bottom. Save the settings, and then restart the system.
DVG-7022S/7044S/7062 User’s Manual Network Settings BigPond (for Australia only) Click “BigPond Cable” and enter the User Name and Password. Then click the “Accept” button at the bottom of the screen. (DNS) Settings Domain Name Server (DNS): While a gateway is accessing another gateway or a computer with a hostname, it will look up the IP address from the DNS provided by your ISP. Normally, the ISP assigns DNS information while negotiating with PPPoE or DHCP.
DVG-7022S/7044S/7062 User’s Manual Network Settings Using Phone Book Manager y Enable Phone Book Manager Server: this allows other gateway users to register the IP address and telephone number in this Phone Book manager. It is recommended that the unit appointed as the Phone Book Manager use static IP.
DVG-7022S/7044S/7062 User’s Manual Network Settings 3-2 Network Settings (LAN) LAN IP/Subnet mask Gateway LAN Port IP address and subnet mask settings. D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual Network Settings y Enable DHCP Server: Enable or Disable DHCP server service of the gateway. y IP Pool Starting Address: The first IP address to be assigned to DHCP clients. y IP Pool Ending Address: The last IP address to be assigned to DHCP clients. y IP Pool Uses Other Default Gw: Tick the check box to give DHCP client the other default gateway. y IP Pool Default Gateway: Assign the default gateway and subnet mask to DHCP client.
DVG-7022S/7044S/7062 User’s Manual Qos Settings 3-3 QoS Settings WAN QoS y QoS (Quality of Service): Sets true bandwidth of your Internet connection to ensure sound quality during transmission. (When this function is enabled, voice packets have the highest priority to ensure telecommunication quality while less bandwidth is assigned for data transmission.) Some models of the VoIP gateway without this function will adjust bandwidth automatically.
DVG-7022S/7044S/7062 User’s Manual Qos Settings * VLAN – This feature is only supported for the special hardware. VLAN is optional. It works with the Router or Switch that supports VLAN. There are 2 VLAN groups: Voice and data (LAN). This improves efficiency of network performance and security. y Enable VLAN Tagging: It is to tag the packets for VLAN Router or Switch identifying. y VLAN ID: It is to assign uniquely a user-defined ID to each packet.
DVG-7022S/7044S/7062 User’s Manual Caller ID 3-4 NAT/DDNS NAT Traversal If your gateway is set up behind an Internet sharing device, you can select either the NAT or STUN protocol. y NAT Public IP: The IP address used by the gateway should be a private address. Furthermore, users must set Virtual Server Mapping in the Internet sharing device.
DVG-7022S/7044S/7062 User’s Manual Caller ID DDNS D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual Caller ID These settings are only necessary when the gateway is set up behind an Internet sharing device that uses a dynamic IP address and does not support DDNS. Choose a DDNS Server: The current system allows users to choose either DynDNS、TZO、3322.org、PeanutHull or a private server. You will need to apply for an account with DynDNS、TZO、3322.org、PeanutHull or a private server before you type in the following information.
DVG-7022S/7044S/7062 User’s Manual Caller ID 3-5 Caller ID y FXS Caller ID Generation: Select this option to enable the caller ID display function on FXS ports. When enabled, the caller’s phone number will be displayed on your phone set when the call comes through. FSK is preferred in some countries. y Send Caller ID After The First Ring: When enabled, the caller’s phone number will be sent to your phone set after the first ring-on. When disabled, caller id will be sent before the First ring-on.
DVG-7022S/7044S/7062 User’s Manual Caller ID Transit In Caller ID Strip / Replace y Scan code: Defines the rule of the Caller IDs detected by FXO. It can be a prefix or a full number. y Substitude: Defines the changed display info. of the calling party while making calls to Internet by FXO. D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual Telephony Settings 3-6 Telephony Settings Prefix Number Rules y Trunk Dial Out Verify/ Trunk Dial Out Replace: VoIP gateway will check (verify) the dial out prefix from dial out numbers and change (replace) the prefix to transit out through FXO port. Example: If you transit out with 01907123456, the system will transfer to 190601 907123456. If you transit out with 008621123456 the system will replace it with 190200 8621123456. The maximum digit is 40.
DVG-7022S/7044S/7062 User’s Manual y Telephony Settings Enable: To enable a line; if some lines are not used, disable them (Pause Function) to avoid unnecessary waiting when an incoming call is diverting to this line. Hotline Functions y FXS port: When the user picks up the phone, the gateway automatically dials your assigned hotline number. When in hotline mode, other phone numbers cannot be dialed.
DVG-7022S/7044S/7062 User’s Manual Telephony Settings y FXS Group: Select group hunting when there is an incoming call and the gateway will automatically assign an unassigned call according to the Hunting Priority. If Line 2 does not want to be set as an assigned line to receive any inbound calls, the function can be disabled. Users can also use the Up or Down key to adjust hunting priority (No setting is required for the FXO interface).
DVG-7022S/7044S/7062 User’s Manual y Telephony Settings Trunk Hunting Order: To set FXO dial-out mode when there is an incoming call dialed FXO representative number. First Idle: The gateway will assign each unassigned call from first FXO line. Sequential: The gateway will automatically assign the first unassigned call to the first FXO line. The second FXO line will dial the second unassigned call out. Each line will be used.
DVG-7022S/7044S/7062 User’s Manual Telephony Settings y VoIP Calling Notification: The gateway will play a tone to notify that the call is via VoIP. y Enable Built-in Call Hold Music: The default setting is that when receiving a call hold request, the gateway will play music on hold. Untick the check box to disable this function while necessary. y Force Calling Thru PSTN code: Dial the code to get a PSTN line for dialing out.
DVG-7022S/7044S/7062 User’s Manual SIP 3-7 SIP FXS/ FXO Representative number registers to Proxy: y Assuming that your registered ID and password are individual, the settings should be as above. FXS Representative Number: Register all FXS ports as a hunting group. y FXO Representative Number: Register all FXO ports as a hunting group. All the grouped FXO ports will be hunted automatically. It is available when FXO registers to Proxy. y Register: Register to proxy if selected.
DVG-7022S/7044S/7062 User’s Manual SIP DNS SRV Settings y Use DNS SRV: The gateway asks for the related IP address of SIP Server from the records of DNS SRV. DNS SRV uses several servers for a single domain for SIP proxy, to move services from host to host and design some hosts as primary servers (the highest priority) for a service and others as backups.
DVG-7022S/7044S/7062 User’s Manual SIP y Proxy Server IP/Domain: Enter the Proxy Server IP address or URL (Uniform Resource Locator). y Proxy Server Port: Enter the Proxy Server listen port number. (The default value is 5060) y Proxy Server Realm: This variable is used for gateway SIP account authentication in a SIP server. In most cases, the gateway can automatically detect your SIP server realm. So you can leave this option blank.
DVG-7022S/7044S/7062 User’s Manual y Enable P-Assert: This variable is for caller ID protection. y Privacy Type: Privacy type is used to disguise the caller ID when queried via an ITSP/Third-Party Assertion. SIP y y SIP Message Resend Timer Base: SIP packet will resend if response did not arrive in the base time set in this column. It will send again at "base time" * 2, and send again at "base time" *2 *2. The maximum resend time is four seconds.
DVG-7022S/7044S/7062 User’s Manual SIP y Put Caller ID In URI: This feature is to put Caller ID in URL. The Caller ID is located in SIP → Message Header → After [From:], Before [
DVG-7022S/7044S/7062 User’s Manual Calling Features 3-8 Calling Features y Do Not Disturb: The particular line will only be able to call out when this variable is enabled. All incoming calls will be rejected. y Unconditional Forward: All incoming calls will be forwarded to the “Forwarding Number” automatically. If it forwards to FXO, it only make FXO hook off, not make FXO dial out. y Busy Forward: Forward incoming calls to the “Forwarding Number” when the port is busy.
DVG-7022S/7044S/7062 User’s Manual y Calling Features Enable Call Feature Code: User could enable/disable some call features with a phone set. NOTE: In most VoIP provider, please disable this function to use call features provided by SoftSwitch. 1. If you would like enable DND function of FXS #2. Please pickup FXS #2 and dial “*74#” 2. If you would like enable Unconditional Forward of FXS #3 and assign the number. Please pickup FXS #3 and dial “*77 0912345678#”.
DVG-7022S/7044S/7062 User’s Manual Advanced Options 3-9 Advanced Options NOTE: There are two operating levels when entering the Web UI. Logging-in as the Administrator allows you to change all settings. A Web UI user only has access to some settings. y Administrator’s Name and Password: Enter the administrator name and password, which has the highest level of control of the gateway.
DVG-7022S/7044S/7062 User’s Manual y Advanced Options Enable Out-of-Band DTMF: To send DTMF keys (0~9, *, #,) follow the RFC2833 rules or via SIP Info. NOTE: Out-of-Band DTMF transport method may vary with different VoIP networks, please contact your VoIP provider for their preferred method. y y Payload Type: payload type of RFC2833. y Volume: Defines the volume of RFC2833. y SIP_INFO: This is an alternative for DTMF event over IP.
DVG-7022S/7044S/7062 User’s Manual y Advanced Options FXO: This option forces the gateway to detect the reversal of polarity on FXO port as the primary signal to drop a call. Some telephone switches or PBX reverse the line polarity to inform the remote end to drop an ongoing call. Please consult with the telephone service provider for availability of this feature. PSTN Answer Detection: This is used only by ITSP.
DVG-7022S/7044S/7062 User’s Manual Advanced Options Fax Settings y NOTE: When a fax tone is detected in a call, the gateway will automatically switch from voice mode to fax mode. So fax settings will be temporarily applied to a specific port which detects fax tones, instead of its default voice settings. Enable High Quality: The system sends the same fax frame twice to get a high quality fax transmission. Enabling this variable increases bandwidth requirements. y T.30: The system uses T.
DVG-7022S/7044S/7062 User’s Manual Digit Map 3-10 Digit Map Digit Map now is combined the original feature of Digit Map and Speed Dial. You can use “?” or “%” in the column of Scan Code, VoIP Dial-out and PSTN Dial-out. “?” is a single digit, and “%” is wildcard. It provides a mapping between the number received from user and the replaced or modified number for real dial out. With this function, user can easily add certain leading digits to replace full number.
DVG-7022S/7044S/7062 User’s Manual Digit Map Digit Map Rule y Enable: Enable detection of this entry. y Scan Code: Defines the digits for the gateway to scan while user is dialing. y VoIP Dial-out: Defines the dialed number rule for the gateway to call through Internet. y PSTN Dial-out: Defines the dialed number rule for the gateway to call through PSTN. y User Dial Length: Defines total number of digits that user dialed.
DVG-7022S/7044S/7062 User’s Manual Digit Map Method 2- Multi mapping: Fill the prefix code into the Scan Code column and the format to transfer into the VoIP Dial-out or PSTN Dial-out column. For example, Scan Code: 2??? PSTN Dial-out: 35106??? User Dial Length: 4 Route: PSTN Pick up the handset and dial 2301. The system will dial 351006301 and go through PSTN/FXO. You also can use Digit Map Testing to know that the system will dial 351006301 and go through PSTN/FXO.
DVG-7022S/7044S/7062 User’s Manual Digit Map Method 3- Substitution: It helps you dial to destination that you can not dial by phone. Destination like: test@1.1.1.1. Fill the number into the Scan Code column and enter the desired name into the VoIP Dial-out column. For example, Scan Code: 11 VoIP Dial-out: test User Dial Length: 2 Route: Auto Pick up the handset and dial 11. The system will dial “test” and go through Internet. You also can use Digit Map Testing to know the dialing result.
DVG-7022S/7044S/7062 User’s Manual Phone Book 3-11 Phone Book This system can set up and store 100 phone numbers into a phone book and provides an IP address query when calling to other gateway(s). If no Phone Book manager is set within a gateway group, then all gateway systems have to set up phone data to allow each gateway to communicate with the others. y Gateway Name: Enter another gateway’s code or an easy-to-remember name. y Gateway Number: Enter the desired number of another gateway.
DVG-7022S/7044S/7062 User’s Manual Caller Filter 3-12 Caller Filter This function is used to allow or deny SIP invitations from the proxy list ONLY. y Filter IP Address: Enter the start IP you would like to allow or deny. y Subnet mask: Enter the subnet mask you would like to allow or deny. D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual CDR Settings 3-13 CDR Settings The user can set up a CDR Server to record call details for every phone call. CDR provides call detail recording in a text file and which can be imported to prepare an analysis report. y Send record to CDR Server: Enables call detail recording. y CDR Server IP: Enter the IP address of the CDR server. y Port: Enter the listen port of the CDR server. y Support RADIUS: Enable RADIUS for CDR database.
DVG-7022S/7044S/7062 User’s Manual Language 3-14 Language The system provides English, Traditional Chinese, and Simplified Chinese for displaying text on web pages. Changing the language setting also changes the language for IVR (Interactive Voice Response). D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual Transit Call Control 3-15 Transit Call Control If you wish to restrict a general user (one who is not required to enter the PIN code) to local calls only and prohibit him/her from making long-distance calls started with a prefix “0”, do the following steps: 1. Enable the Outbound Call Control function, 2. Set the PIN code for Outbound Level 5 to blank, 3.
DVG-7022S/7044S/7062 User’s Manual Long-Distance Control Table 3-16 Long-Distance Control Table This table controls the level of authority of an outgoing (transit out) call that is dialed through FXO and diverted to PSTN, as below: Descriptions: y Digit strings in this table are prefixes that the gateway will check on dialed numbers in transit out calls. y This table is used to prohibit dialing any numbers started with specified prefixes.
DVG-7022S/7044S/7062 User’s Manual Long-Distance Exception Table 3-17 Long Distance Exception Table This table handles any exceptions to the long-distance call table. Instruction: y According to the Long Distance Control Table, users at Level 0 are prohibited from dialing a number with the prefix 0204. But, if the number 020488988 is set in the Exception Table as above, then users can dial this number.
DVG-7022S/7044S/7062 User’s Manual CPT/Cadence Setting 3-18 CPT/Cadence Settings The CPT has 3 sets of parameter tables. Please adjust the CPT based on the local PSTN or PBX settings and requirements. Busy Tone Cadence Measurement y Busy Tone Cadence Measurement and auto learning: Provides a solution of FXO integrated with PSTN or PBX. FXO will learn the busy tone automatically. y BTC Detection Sensitivity: The more sensitivity, the more quickly the system will cut off the call.
DVG-7022S/7044S/7062 User’s Manual CPT/Cadence Setting UDT Detection If the CPT auto detect function is not able to determine whether or not a PSTN-call receiving party has hung up the phone, then the UDT detection function can serve as a back up. To do this, enter the high/low frequency parameters from the CPT table into the UDP table. NOTE: If FXO cut off calls un-normally, please disable this function. FXS Ring Cadence Settings y FXS Ring Cadence Settings: Specify the ring cadence for the FXS port.
DVG-4088S/4032S User’s Manual Current Status 3-19 Current Status y Port Status: it includes if each port registers to Proxy successfully, the last dialed number, how many calls each port has made since the Gateway is start, etc. y Server Registration Status: It shows the registration status of DDNS, Phone Book Manager, STUN and UPnP. D-Link Systems, Inc.
DVG-4088S/4032S User’s Manual RTP Packet Summary 3-20 RTP Packet Summary Display the information of the last completed call. This report contains peer IP, peer port, packets sent, packet received, and packet loss information. Press the Refresh button to get the latest RTP Packet Summary. D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual System Information 3-21 System Information These two pages show the status of the VoIP gateway. The categories are WAN Port Information, LAN Port Information and Model Information. y WAN Port Information: it shows IP address, subnet mask, default gateway and DNS server. If you use PPPoE to obtain IP, you will know if the IP is obtained through this method. If IP address, subnet mask, default gateway is blank, it means that the VoIP Gateway does not obtain IP.
DVG-7022S/7044S/7062 User’s Manual Routing Table 3-22 Routing Table The Routing Table stores the information for particular network destination around the VoIP gateway. Press the Refresh button to generate the details. D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual STUN Inquiry 3-23 STUN Inquiry Use “STUN Inquiry” to detect your IP sharing device’s NAT type and communication between a STUN server and client (built-in to the DVG-7022S/7044S/7062 gateway). D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual Ping Test 3-24 Ping Test Use “Ping” to verify if a remote peer is reachable. Enter a remote IP address and click “Test” to ping the remote host. D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual Static Route 3-25 Static Route Build static routes within an internal network. These routes will not apply to the Internet. y Route: Enter the IP of the specified network. y Route Mask: Enter the subnet mask to be used for the specified network. y Next Hop IP: Enter the IP address to the specified network. y Interface: Select the interface. D-Link Systems, Inc.
DVG-5004S/5008S User’s Manual Port Filtering 3-26 Port Filtering Port filtering enables you to control all data that can be transmitted over routers. When the port used at the source end is within the defined scope, it will be filtered without transmission. y Enable Port Filtering: Select to enable this function. y Port Range: Set the range of ports to be filtered.
DVG-5004S/5008S User’s Manual IP Filtering 3-27 IP Filtering IP Filtering is used to limit internal users from accessing the Internet. y y y IP: Input the IP address that you want to filter. The listed IP address will be unable to transmit data to and from the Internet. TCP/UDP: Choose to filter TCP, UDP, or both. Remark: This field allows you to enter comments. D-Link Systems, Inc.
DVG-5004S/5008S User’s Manual MAC Filtering 3-28 MAC Filtering MAC (Media Access Control) address filtering allows you to filter the transmission of data by network card physical address. y MAC: Enter a MAC address to prevent the particular device from accessing the Internet. D-Link Systems, Inc.
DVG-5004S/5008S User’s Manual Virtual Server 3-29 Virtual Server Virtual server allows you to enable users to access the Internet, FTP and other services from behind your NAT. When remote users are accessing web or FTP servers through WAN-end IP addresses, they will be routed to the server at the internal LAN end as appropriate in accordance with externally required services y WAN Port Range: Input the port range for the WAN side.
DVG-5004S/5008S User’s Manual DMZ 3-30 DMZ DMZ allows the server on the LAN site to be directly exposed to the Internet for accessing data. Either this function or virtual server can be selected for use in accessing external services. D-Link Systems, Inc.
DVG-5004S/5008S User’s Manual URL Filter 3-31 URL Filter URL filtering is used to deny devices on the LAN from accessing specific web sites. The system will block any URL that contains the strings listed. D-Link Systems, Inc.
DVG-5004S/5008S User’s Manual Special Applications 3-32 Special Applications Provide multiple connections for special applications. y Name: The name of the special application. y Incoming Type: The protocol used to trigger the special application. y Incoming Port Range: Port range on the WAN side that will be used to access the application. y Trigger Type: The protocol used to trigger the application. y Trigger Port Range: Port range used to trigger the application. D-Link Systems, Inc.
DVG-5004S/5008S User’s Manual DoS Prevention Settings 3-33 DoS Prevention Settings y Enable DoS Prevention: To prevent DoS attacks from WAN. y Enable DoS Prevention on LAN: To prevent DoS attacks from LAN. y Enable Source IP Blocking: Block a particular IP. y Blocking Time: The time to block the IP. D-Link Systems, Inc.
DVG-5004S/5008S User’s Manual NTP (Network Time Protocol) 3-34 NTP (Network Time Protocol) y Time Zone: Set the Time Zone where the gateway resides. y Time Server #1~#3: Set the Time Server where the gateway should sync up during start up. D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual SNMP 3-35 SNMP y Enable SNMP Agent: Enable SNMP if selected. y Get/Set/Trap Community: Enter Community name to Read, Write and Trap. y Trap Host: Enter the IP of the Trap Host. D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual Backup/Restore 3-36 Backup/Restore You can backup settings to a file and restore settings from that file. You also can restore all settings back to default by selecting Restore Default Configurations and click Restore. • NOTE: the gateway needs for you to Save Settings and Restart so that all settings will be backed up. y Configuration File: Backup all settings. y Configuration Template File: Backup the settings as a template file for editing.
DVG-7022S/7044S/7062 User’s Manual System Log 3-37 System Log It will send all logs to the server. Please contact with your provider. D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual Provision Settings 3-38 Provision Settings Options in this section are only required for VoIP networks in which a provisioning system has been implemented. Fill in the parameters needed by the Provision Server from your service provider. NOTE: The availability of the above features also depends on your VoIP network. Please check with your service provider about the availability of these services. D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual System Operations 3-39 System Operations (Save Settings) Some settings are effective only after Restart. Remember to save all settings using Save Settings before you restart. y Save Settings: Save settings after completing changes. The new settings will take effect after the system is restarted. Please select “Save Settings”. y Restart: If it is necessary to restart the system, please select “Restart” and click the “Accept” button. D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual Software Upgrade 3-40 Software Upgrade The gateway provides a software upgrade function from a remote source. Please consult your service provider for information about the following details. y Upgrade Server: Choose the server type given by your provider. y Software Upgrade Server IP: Enter the software server IP address. y Software Upgrade Server Port: Enter the port that the server uses. TFTP is 69, and FTP is 21.
DVG-7022S/7044S/7062 User’s Manual Logout 3-41 Logout The gateway only allows one user at a time to log-in, so whenever a change is made, please save the settings and restart the system, or logout to avoid a situation where other users cannot log-in to change settings. D-Link Systems, Inc.
DVG-7022S/7044S/7062 User’s Manual Gateway Configuration-IVR 4. Configuring the Gateway through IVR VoIP transmits voice data (packets) via the Internet. One effect of this is that telecommunications quality is closely related to the condition and status of the network environment. If any of the parties involved in VoIP communications has insufficient bandwidth or frequent packet loss, the telecommunication quality will be poor.
DVG-7022S/7044S/7062 User’s Manual Gateway Configuration-IVR Save Settings After completing all of your settings, dial 509 (Save Settings). Wait for about three seconds, you should hear a confirmation tone “1.” You can now hang up the phone. Please reboot the gateway to enable the new settings. To inquire about the current gateway WAN Port IP address setting After completing all your settings, dial 101. The system will repeat the current WAN Port IP address.
DVG-7022S/7044S/7062 User’s Manual Gateway Configuration-IVR 4-2 IP Configuration Settings—Set the IP Configuration of the WAN Port Static IP Settings NOTE: Complete static IP settings should include a static IP (option 1 under 114), IP address (111), Subnet Mask (112), and Default Gateway (113). Please contact your Internet Service Provider (ISP) if you have any questions. Function Command Select a Static IP y After entering IVR mode, dial 114.
DVG-7022S/7044S/7062 User’s Manual Gateway Configuration-IVR Select a PPPoE y After entering IVR mode, dial 114. y After hearing “Enter value,” dial 3 (to select PPPoE). PPPoE Account Settings y After entering IVR mode, dial 121. y After hearing “Enter value”, enter the account number followed by”#”. Example: If the account is “84943122@hinet.net,” please enter 08 04 09 04 03 01 02 02 71 48 49 54 45 60 72 54 45 60 #.
DVG-7022S/7044S/7062 User’s Manual Gateway Configuration-IVR PPPoE Character Conversion Table: The table below provides a list of PPPoE conversion codes. The first column in each pair of columns lists the number, letter or symbol that you want to enter. The second column in each pair (“Input Key”) tells you what code to enter for the corresponding number, letter or symbol.
DVG-7022S/7044S/7062 User’s Manual Dialing Principles 5. Dialing Principles 5-1 Dialing Options 1. 2. 3. Dial the phone number which you want to call and press # to call out immediately, or wait until the “Inter Digits Timeout” expires (defined in “Advanced Options”, default=4 seconds, see page 23). If the phone number fits the setting of the Digit Map, the gateway dials out the phone number through the assigned interface automatically.
DVG-7022S/7044S/7062 User’s Manual Dialing Principles 5-3 Example for Match phone numbers invited by callers The table below is provided as a general reference expresses phone numbers dialed by the gateway instead of real phone numbers that callers dial.
DVG-7022S/7044S/7062 User’s Manual Dialing Principles Start Enter a phone number (D#) Dial the number defined in Digt Map table Yes Is (D#) defined in Digit Map table? No Is (D#) defined in Extension table? Yes No Is (D#) defined in Phone Book table? Yes No Is (D#) defined in Phone Book Manager? Yes No Is (D#) defined in SIP proxy server? Yes No Dial (D#) through the first available FXO port to PSTN Dial out as defined in the first match case through the gateway Yes Does this gateway ha
DVG-7022S/7044S/7062 User’s Manual Appendix Appendix Product Features WAN • One 10/100Mbps auto-negotiation, auto-MDI/MDIX RJ-45 Ethernet port • Support static IP, PPPoE, BigPond Cable and DHCP address assignment and dynamic DNS (DDNS) • QoS: IP TOS (Type of Services) and DiffServ (Differentiated Services) for both SIP signaling and RTP • NAT Traversal : Port Forwarding, STUN, UPnP and Outbound Proxy • NTP: (Network Time Protocol RFC 1305), Accepts up to 3 Time Server • Time Zone Support • MAC Address Clo
DVG-7022S/7044S/7062 User’s Manual • • Appendix Call features: o Call Hold, Call Waiting, Call Pickup o Call Forward - Unconditional, Busy, No Answer o Call Transfer - Unattended, Attended o Three Way Calling (Media Server required) Analogue interface o Connector : RJ-11 o Signaling protocol : Loop Start Configuration & Maintenance • Configuration methods: o Web o IVR o Telnet • Status reports: o Port status o Registration status o Ping tests o STUN/UPnP status o Hardware / software information • Firmwa
