DVG-5112S VoIP TA User’s Manual Version 1.
© 2007 D-Link Corporation. All rights reserved. Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of D-Link Corporation/D-Link Systems Inc.; Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Contents 1. Introduction....................................................................................................4 1-1 Product Overview.................................................................................................................................... 4 1-2 Hardware Connections and Description ................................................................................................. 5 2. Installation and Applications ........................................................
DVG-5112S User’s Manual 1. Introduction 1-1 Product Overview The DVG-5112S VoIP Gateway carries both voice and facsimile over the IP network. It uses the industry standard SIP call control protocol so as to be compatible with free registration services or VoIP service providers’ systems. As a standard user agent, it is compatible with all common Soft Switches and SIP proxy servers.
DVG-5112S User’s Manual 1-2 Hardware Connections and Description Front Panel Power/Alarm Indicator: Green light indicates a normal power supply. Red light indicates when performing a self-test/booting up or the DVG-5112S’s abnormal operation. VoIP Indicator: Blinking green light indicates normal operation. It will light on green when DVG-5112S is registered with the service provider. Phone1/Phone2 Indicator: Phone LED should be in orange while Phone in use.
DVG-5112S User’s Manual DC+12V PHONE2 PHONE1 LAN WAN 3 4 1 2 INTERNET 1. DC+12V: Connect to the bundled power adaptor. Plug power adapter to a proper power source. 2. Phone: Connect to your analog telephone. These are FXS (Foreign Exchange Station) ports. 3. LAN: Connect to a PC for later DVG-5112S configuration. 4. WAN: Connect to your broadband device with RJ-45 cable. D-Link Systems, Inc.
DVG-5112S User’s Manual 2.
DVG-5112S User’s Manual DVG-5112S in a NAT network Under this mode, the gateway uses a virtual IP address and the IP sharing function of other systems to connect to the Internet. LAN IP address for IP sharing Please avoid IP addresses in the following range: 192.168.8.1-192.168.8.
DVG-5112S User’s Manual DVG-5112S assigned with a Public IP Address and serving as a Bridge DVG-5112S will have a public IP address regardless of whether it is a static IP application, DHCP (using a Cable Modem), or PPPoE (to connect to your ADSL account), which can then use the functions of built-in IP sharing to allow other PCs to be on-line at the same time.
DVG-5112S User’s Manual 3. Setting a DVG-5112S with WEB Browser DVG-5112S allows users to configure its settings using a web interface (Web UI). You can access the Configuration Menu by opening a web-browser (e.g., Internet Explorer or Netscape Navigator) and entering the factory default LAN IP address: 192.168.8.254. The IP address of the Web UI is same as the default LAN IP noted elsewhere in this user’s manual.
DVG-5112S User’s Manual 3-1 Current Status Refresh Time: Set the time to update Port Status and Server Registration Status. Port Status: It includes if each port registers to Proxy successfully, the lasted dialed number, how many calls each port had since DVG-5112S is start, etc. Server Registration Status: It shows the registration status of DDNS, Phone Book Manager, STUN and UPnP. 3-2 RTP Packet Summary Display the information of the final call.
DVG-5112S User’s Manual 3-3 System Information WAN Port Information: It shows IP address, subnet mask, default gateway and DNS server. If you use PPPoE to obtain IP, you can know if the IP is obtained through this. If IP address, subnet mask, default gateway is blank, it means that DVG-5112S does not obtain IP. LAN Port Information: It shows LAN port IP, subnet mask, and the status of DHCP server. Hardware: It shows the hardware platform. D-Link Systems, Inc.
DVG-5112S User’s Manual 3-4 WAN WAN Configuration includes the method of obtaining IP, the setting of DNS (Domain Name Server), etc. Current WAN IP Address: The IP address of the WAN port. D-Link Systems, Inc.
DVG-5112S User’s Manual IP Configuration There are five methods of obtaining a WAN port IP address: 1. Static IP 2. DHCP, which means a Dynamic IP (Cable Modem) 3. PPPoE (dial-up ADSL) 4. PPTP 5. BigPond (for Australia only) Methods for using DHCP and PPPoE for obtaining an IP address may vary. If you are not familiar with creating a network connection, please contact your local ISP.
DVG-5112S User’s Manual PPTP Select “PPTP” and enter the IP Address, Subnet mask, PPTP Server, PPTP ID and Password. Then click the “Accept” button at the bottom of the screen. BigPond (for Australia only) Click “BigPond Cable” and enter the User Name and Password. Then click the “Accept” button at the bottom of the screen.
DVG-5112S User’s Manual VLAN Enable VLAN Tagging: this tags the packets for VLAN Router or Switch identifying. VLAN ID: enter a uniquely user-defined ID to each packet. Priority: enter the proprietary. WAN QoS QoS (Quality of Service): Sets true bandwidth of your Internet connection to ensure sound quality during transmission. (When this function is enabled, voice packets have the highest priority to ensure telecommunication quality while less bandwidth is assigned for data transmission.
DVG-5112S User’s Manual 3-5 LAN LAN IP/Subnet mask Gateway LAN Port IP address and subnet mask settings. Enable DHCP Server: Enable or Disable DHCP server service of the gateway. IP Pool Starting Address: The first IP address to be assigned to DHCP clients. IP Pool Ending Address: The last IP address to be assigned to DHCP clients. IP Pool Uses Other Default Gw: Tick the check box to give DHCP client the other default gateway.
DVG-5112S User’s Manual 3-6 SIP Assuming that your registered ID and password are individual, the settings should be as above. Number: VoIP phone number Register: Register to proxy if selected. Invite with ID / Account: The DVG-5112S can be invited to a VoIP trunk gateway without registering to a proxy. Please contact your VoIP service provider.
DVG-5112S User’s Manual Enable Support of SIP Proxy Server / Soft Switch Enable Support of SIP Proxy Server / Soft Switch: Enable the functions to inter-work with Proxy Server / Soft Switch. When SIP Proxy 1 and 2 are enabled, the system will register to SIP Proxy 2 after all lines have failed to register to SIP Proxy 1. SIP Proxy 2 is a backup system. Proxy Server IP/Domain: Enter the Proxy Server IP address or URL (Uniform Resource Locator). You can set three redundant Proxy IPs separated by semicolons.
DVG-5112S User’s Manual Outbound Proxy All Call through OutBound Proxy：An outbound proxy server handles SIP call signaling as a standard SIP proxy server would. Further, it receives and transmits phone conversation traffic (media) between two communication parties. This option tells the gateway to send and receive all SIP packets to the destined outbound proxy server rather than the remote gateway. This helps VoIP calls to pass through any NAT protected network without additional settings or techniques.
DVG-5112S User’s Manual 3-7 SIP Advanced Listen Port UDP: It is not necessary to change the protocol of the communication port used by the gateway, unless it conflicts with ports used by another device in your network. RTP Starting Port UDP: The initial value of the port number for transmitting voice data among gateway(s). Each line requires 2 ports. For the DVG-5112S gateway 4 UDP ports are required. It is not necessary to change the setting, unless it conflicts with ports used by another network device.
DVG-5112S User’s Manual SIP Proxy Server / Soft Switch Settings VoIP failure announcement: As soon as the registration to proxy server is failed, the gateway will drive IVR system to play out failure announcements for the caller. Bind Proxy Interval for NAT: This function is able to keep the binding that exists when the VoIP gateway is behind a NAT and SIP Proxy is not able to keep the binding.
DVG-5112S User’s Manual VoIP Calling Notification: The gateway will play a tone to notify that the call is via VoIP. Enable Built-in Call Hold Music: The default setting is that when receiving a call hold request, the gateway will play music on hold. Untick the check box to disable this function while necessary. Enable P-Assert: This variable is for caller ID protection. Privacy Type: Privacy type is used to disguise the caller ID when queried via an ITSP/Third-Party Assertion.
DVG-5112S User’s Manual 3-8 Phone Book Using Phone Book Manager Register to Phone Book Manager: To register to the Phone Book Manager. VoIP failure announcement: As soon as the registration to proxy server is failed, the gateway will drive IVR system to play out failure announcements for the caller. Gateway Name for Phone Book Manager: The alias registered with the Phone Book Manager. Phone Book Manager IP/Domain: Enter the IP address for the Phone Book Manager.
DVG-5112S User’s Manual 3-9 Caller ID FXS Caller ID Generation: Select this option to enable the caller ID display function on FXS ports. When enabled, the caller’s phone number will be displayed on your phone set when the call comes through. FSK is preferred in some countries. FSK Caller ID Type: Bellcore is used in Australia caller ID standards.
DVG-5112S User’s Manual 3-11 Calling Features Do Not Disturb: The particular line will only be able to call out when this variable is enabled. All incoming calls will be rejected. Unconditional Forward: All incoming calls will be forwarded to the “Forwarding Number” automatically. Busy Forward: Forward incoming calls to the “Forwarding Number” when the port is busy. No Answer Forward: Forward incoming calls to the “Forwarding Number” after ring timeout expires without answer.
DVG-5112S User’s Manual 3-12 Virtual Server Virtual server allows you to enable users to access the Internet, FTP and other services from behind your NAT. When remote users are accessing web or FTP servers through WAN-end IP addresses, they will be routed to the server at the internal LAN end as appropriate in accordance with externally required services WAN Port Range: Input the port range for the WAN side. TCP/UDP: Select the communication protocols used by the server, TCP or UDP.
DVG-5112S User’s Manual 3-14 NAT Traversal If your gateway is set up behind an Internet sharing device, you can select either the NAT or STUN protocol. NAT Public IP: The IP address used by the gateway should be a private address. Furthermore, users must set Virtual Server Mapping in the Internet sharing device. (For example, a virtual server is usually defined as a Service Port, and all requests to this port will be redirected to this specified server’s private IP address).
DVG-5112S User’s Manual 3-15 DDNS These settings are only necessary when the gateway is set up behind an Internet sharing device that uses a dynamic IP address and does not support DDNS. Choose a DDNS Server: The current system allows users to choose either DynDNS、TZO、3322.org、PeanutHull or a private server. You will need to apply for an account with DynDNS、TZO、3322.org、PeanutHull or a private server before you type in the following information. D-Link Systems, Inc.
DVG-5112S User’s Manual Server address: the IP address or URL (Uniform Resource Locator) of the DDNS Server. Hostname: the URL of the system (or NAT) – applied from domain name registration providers (e.g. www.dyndns.org). Login ID and Password: The ID and password used to log-in to the DDNS server. Behind NAT: Select this only when the system is set up behind a NAT device. NOTE: If the gateway is set up under NAT, then enter the hostname in the NAT IP/Domain that is the same as the Hostname of the DDNS.
DVG-5112S User’s Manual 3-16 FAX Settings T.38: The T.38 protocol is used for better and faster facsimile transmission. So it is recommended to enable this function to gain better fax quality. When this function is enabled, please select UDP or TCP. If you select TCP and some gateways cannot use the fax function, please select UDP instead. NOTE: When a fax tone is detected in a call, the gateway will automatically switch from voice mode to fax mode.
DVG-5112S User’s Manual 3-17 Codec Settings Preferred Codec Type: Since different voice codecs have different compression ratios, the sound quality and occupied bandwidths are also different. It is recommended that you use the default provided (G.723.1) because it occupies less bandwidth and will provide better sound quality. Jitter Buffer: Adjusts the jitter for receiving packets. If the jitter range is too wide, it will delay voice transmission.
DVG-5112S User’s Manual 3-18 Line Settings Listening Volume: Adjusts the earpiece or speaker volume. Speaking Volume: Adjusts the microphone volume. Tone Volume: Adds a new option to make tone volume adjustable. This setting will be applied to all tones generated by the gateway including dial tone and busy tone. Min. FXS Hook Flash Time: It is to set the minimum flash time for FXS detecting. Flash Time: Used to adjust the detection period for flash signals from a phone set connected to an FXS port.
DVG-5112S User’s Manual Enable ROH: The system will play Receiver Off-Hook tone to notify user of hanging up the phone set. VoIP Centrex Extension Digit Count: Sets the digit counts of VoIP Centrex Extension. VoIP Centrex Digit: Enter the digit for VoIP Centrex. Termination Impedance Choose the correct impedance in your country or area. Drop Inactive Call This is used as a standard to determine whether or not to hang up the phone.
DVG-5112S User’s Manual 3-19 Digit Map Digit Map now is combined the original feature of Digit Map and Speed Dial. You can use “?” or “%” in the column of Scan Code, VoIP Dial-out and PSTN Dial-out. “?” is a single digit, and “%” is wildcard. It provides a mapping between the number received from user and the replaced or modified number for real dial out. With this function, user can easily add certain leading digits to replace full number.
DVG-5112S User’s Manual Methods of Digit Map: Method 1- Single mapping: Fill a short code into the Scan Code column, and enter the desired phone number into the VoIP Dial-out or PSTN Dial-out column. For example, Scan Code: 55 VoIP Dial-out: 07021234567 User Dial Length: 2 Route: Auto Pick up the handset and dial 55 and the system will dial 07021234567. You also can use Digit Map Testing to know that the system will dial 07021234567 and go through Internet.
DVG-5112S User’s Manual For example, Scan Code: 0% PSTN Dial-out: 1805% User Dial Length: 0 Route: Auto Pick up the handset and dial 0423456789. The system will dial 1805423456789 and go through Internet first. If the call is fail to Internet, the system will play busy tone. Method 3- Substitution: It helps you dial to destination that you can not dial by phone. Destination like: test@1.1.1.1. Fill the number into the Scan Code column and enter the desired name into the VoIP Dial-out column.
DVG-5112S User’s Manual 3-20 Port Filtering Port filtering enables you to control all data that can be transmitted over routers. When the port used at the source end is within the defined scope, it will be filtered without transmission. Enable Port Filtering: Select to enable this function. Port Range: Set the range of ports to be filtered.
DVG-5112S User’s Manual 3-22 DTMF & Pulse Dial Wait Timeout: Use this variable to set the wait time for the user’s first key pressing when dialing a number. The user will hear a busy tone if he or she does not press the first key within the set time frame. Inter Digits Timeout: Set the waiting time between each key press. The numbers input up to that point will be dialed after the timeout.
DVG-5112S User’s Manual 3-23 CPT/Cadence Settings The CPT has 2 sets of parameter tables. Please adjust the parameters based on local PSTN. D-Link Systems, Inc.
DVG-5112S User’s Manual 3-24 Provision Settings Options in this section are only required for VoIP networks in which a provisioning system has been implemented. Fill in the parameters needed by the Provision Server from your service provider. NOTE: The availability of the above features also depends on your VoIP network. Please check with your service provider about the availability of these services. D-Link Systems, Inc.
DVG-5112S User’s Manual 3-25 Caller Filter This function is used to allow or deny SIP invitations from the proxy list ONLY. Filter IP Address: Enter the start IP you would like to allow or deny. Subnet mask: Enter the subnet mask you would like to allow or deny. 3-26 CDR Settings The user can set up a CDR Server to record call details for every phone call. CDR provides call detail recording in a text file and which can be imported to prepare an analysis report.
DVG-5112S User’s Manual 3-27 SNMP Enable SNMP Agent: Enable SNMP if selected. Get/Set/Trap Community: Enter Community name to Read, Write and Trap. Trap Host: Enter the IP of the Trap Host. 3-28 Ping Test Use “Ping” to verify if a remote peer is reachable. Enter a remote IP address and click “Test” to ping the remote host. 3-29 STUN Inquiry Use “STUN Inquiry” to detect your IP sharing device’s NAT type and communication between a STUN server and client (built-in to the DVG-5112S gateway).
DVG-5112S User’s Manual 3-30 NTP (Network Time Protocol) Time Zone: Set the Time Zone where the gateway resides. Time Server #1~#3: Set the Time Server where the gateway should sync up during start up. 3-31 Language The system provides English, Traditional Chinese, and Simplified Chinese for displaying text on web pages. Changing the language setting also changes the language for IVR (Interactive Voice Response). 3-32 Login Account NOTE: There are two operating levels when entering the Web UI.
DVG-5112S User’s Manual Port of Web Access from WAN: HTTP port for WAN. To change this setting, web configuration must be accessed via the gateway’s LAN port. The gateway always uses port 80 for HTTP connection via the LAN port. Web UI auto logout: If a user does not act within the effective time range when logging into the web interface, the user will be disconnected from the web page to allow others to log-in.
DVG-5112S User’s Manual 3-34 System Operations Some settings are effective only after Restart. Remember to save all settings using Save Settings before you restart. Save Settings: Save settings after completing changes. The new settings will take effect after the system is restarted. Please select “Save Settings”. Restart: If it is necessary to restart the system, please select “Restart” and click the “Accept” button.
DVG-5112S User’s Manual 3-36 Logout The gateway only allows one user at a time to log-in, so whenever a change is made, please save the settings and restart the system, or logout to avoid a situation where other users cannot log-in to change settings. D-Link Systems, Inc.
DVG-5112S User’s Manual 4. Setting the DVG-5112S through IVR VoIP transmits voice data (packets) via the Internet. One effect of this is that telecommunications quality is closely related to the condition and status of the network environment. If any of the parties involved in VoIP communications has insufficient bandwidth or frequent packet loss, the telecommunication quality will be poor.
DVG-5112S User’s Manual Save Settings After completing all of your settings, dial 509 (Save Settings). Wait for about three seconds, you should hear a confirmation tone “1.” You can now hang up the phone. Please reboot the gateway to enable the new settings. To inquire about the current gateway WAN Port IP address setting After completing all your settings, dial 101. The system will repeat the current WAN Port IP address.
DVG-5112S User’s Manual 4-2 IP Configuration Settings—Setting IP Configuration of WAN Port Static IP Settings NOTE: Complete static IP settings should include a static IP (option 1 under 114), IP address (111), Subnet Mask (112), and Default Gateway (113). Please contact your Internet Service Provider (ISP) if you have any questions. Function Select a Static IP Command After entering IVR mode, dial 114.
DVG-5112S User’s Manual Select a PPPoE After entering IVR mode, dial 114. After hearing “Enter value,” dial 3 (to select PPPoE). PPPoE Account Settings After entering IVR mode, dial 121. After hearing “Enter value”, enter the account number followed by”#”. Example: If the account is “84943122@hinet.net,” please enter 08 04 09 04 03 01 02 02 71 48 49 54 45 60 72 54 45 60 #. NOTE: it is necessary to enter two digits for each character/number; for example, you must enter “01” for “1” and “11” for “A”.
DVG-5112S User’s Manual PPPoE Character Conversion Table: The table below provides a list of PPPoE conversion codes. The first column in each pair of columns lists the number, letter or symbol that you want to enter. The second column in each pair (“Input Key”) tells you what code to enter for the corresponding number, letter or symbol.
DVG-5112S User’s Manual Appendix Product Features List WAN • One 10/100Mbps auto-negotiation, auto-MDI/MDIX RJ-45 Ethernet port • Support static IP, PPPoE, BigPond Cable and DHCP address assignment and dynamic DNS (DDNS) • QoS: IP TOS (Type of Services) and DiffServ (Differentiated Services) for both SIP signaling and RTP • NAT Traversal : Port Forwarding, STUN, UPnP and Outbound Proxy • NTP: (Network Time Protocol RFC 1305), Accepts up to 3 Time Server • Time Zone Support • MAC Address Clone • RTP Packet
DVG-5112S User’s Manual • Analogue interface o Connector : RJ-11 o Signaling protocol : Loop Start Configuration and Maintenance • Configuration methods: o Web o IVR o Telnet • Status reports: o Port status o Registration status o Ping tests o STUN/UPnP status o Hardware / software information • Firmware Upgrade through TFTP, FTP and HTTP • Configuration Backup/Restore • Reset button (with restore factory default function) • Front Panel LED: voice ports, VoIP, Power / Alarm • Optional Auto Provisioning Se
Safety Instructions Please adhere to the following safety guidelines to help ensure your own personal safety and protect your system from potential damage. Any acts taken that are inconsistent with ordinary use of the product, including improper testing, etc., and those not expressly approved by D-Link may result in the loss of product warranty.
• When connecting or disconnecting power to hot-pluggable power supplies, if offered with your device, observe the following guidelines: • Install the power supply before connecting the power cable to the power supply. • Unplug the power cable before removing the power supply. • If the system has multiple sources of power, disconnect power from the device by unplugging all power cables from the power supplies.
LIMITED WARRANTY D-Link provides this limited warranty for its product only to the person or entity who originally purchased the product from D-Link or its authorized reseller or distributor. D-Link would fulfill the warranty obligation according to the local warranty policy in which you purchased our products.
What Is Not Covered: This limited warranty provided by D-Link does not cover: Products that have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs; Opera
International Offices U.S.A 17595 Mt. Herrmann Street Fountain Valley, CA 92708 TEL: 1-800-326-1688 URL: www.dlink.com Canada 2180 Winston Park Drive Oakville, Ontario, L6H 5W1 Canada TEL: 1-905-8295033 FAX: 1-905-8295223 URL: www.dlink.ca Europe (U. K.) 4th Floor, Merit House Edgware Road, Colindale London NW9 5AB U.K. TEL: +44-20-8955-9000 FAX: +44-20-8955-9001 URL: www.dlink.co.uk Germany Schwalbacher Strasse 74 D-65760 Eschborn Germany TEL: 49-6196-77990 FAX: 49-6196-7799300 URL: www.dlink.
Notes
Registration Card All Countries and Regions Excluding USA Print, type or use block letters. Your name: Mr./Ms_____________________________________________________________________________ Organization: ________________________________________________ Dept.
DI Wired ClassB Warranty Guide_v11
