Table of Contents Table of Contents General Information................................................................................... 4 Package Contents............................................................................................ 4 Important Safety Instructions...................................................................... 4 Front Panel View............................................................................................... 5 Rear Panel View............................
Table of Contents Default Gateway....................................................................................58 Static Route.............................................................................................59 RIP...............................................................................................................60 DNS......................................................................................................................61 Server Configuration.......................
Section 1 - General Information General Information The D-Link DSL-520B is an ADSL2+ modem that offers the convenience of Ethernet connections. This user manual provides a simple and easy-tounderstand format to install and configure your modem.
Section 1 - General Information Front Panel View 4 1 1 Power LED 2 LAN LED 3 4 DSL LED Internet LED D-Link DSL-520B ADSL2+ Modem User Manual 2 3 • • A solid green light indicates the unit is powered on. A red light indicates a malfunction. • A solid light indicates a connection to an Ethernet-enabled computer. This LED blinks during data transmission. • • A solid light indicates the DSL is synchronized A flashing LED indicates the modem is attempting to synchronize with the DSL provider.
Section 1 - General Information Rear Panel View 2 1 3 4 5 1 2 DSL Line • Connect to an active telephone line (RJ-11). LAN Port • Connect Ethernet devices such as computers, switches, and hubs. 3 Reset • Pressing the Reset button for 5 seconds restores the modem to its original factory default settings. 4 5 ON/OFF • Press this button to turn the unit ON or OFF. Power Receptor • Receptor for the supplied power adapter.
Section 2 - Installing The Modem Installing the Modem Connect the ADSL and Telephone Lines • Connect an RJ-11 cable between the wall phone jack and the DSL port on the rear panel of the modem. Connect the PC to the Modem • To use the Ethernet connection, connect the Ethernet cable from the computer directly to the modem. Connect one end of the Ethernet cable to the port labeled LAN on the back of the modem and attach the other end to the Ethernet port of your computer.
Section 2 - Installing The Modem Connect the Power Adapter • Complete the process by connecting the supplied 12V, 500mA power adapter to the POWER connector on the back of the device and plug the adapter into a wall outlet or power strip. Then turn on and boot up your PC and any LAN devices, such as hubs or switches, and any computers connected to them.
Section 3 - Installation Diagram Installation Diagram DSL-520B Modem Desktop Computer LAN D-Link DSL-520B ADSL2+ Modem User Manual LAN RESET ON/OFF 5V - - - 3A 9
Section 4 - Configuring Your Computer Configuring Your Computer Prior to accessing the modem through the LAN or USB port, note the following necessary configurations: • Your PC’s TCP/IP address: 192.168.1.x (where “x” is any number between 2 and 254) • The modem’s default IP address: 192.168.1.1 • Subnet mask: 255.255.255.0 Below are the procedures for configuring your computer. Follow the instructions for the operating system that you are using. Windows® XP 1.
Section 6 - Quick Setup Mac These are instructions for configuring your Mac OS X operating system 1. 2. 3. 4. 5. In the Mac OS X Dock, click on the System Preferences icon. Under Internet & Network, click Network. In the Show menu, select Built-in Ethernet or Ethernet (Depending on your Mac OS version.) Click the TCP/IP tab. In the Configure menu, select Using DHCP. Click Apply Now and Save if your computer prompts you to save changes.
Section 6 - Quick Setup Log in to the Modem This section will explain how to log in to your modem using the following steps: 1. Launch your web browser. 2. Enter the URL http://192.168.1.1 in the address bar and press Enter. A login screen like the one below will be displayed after you connect to the user interface. Note: Use admin/admin as a default for username and password. • The admin account can perform all functions (username / password: admin / admin). Note: Passwords can be changed at any time.
Section 6 - Quick Setup Quick Setup Quick Setup will be the first page you see when you log in to the router. Verify the box is checked next to DSL Auto-connect. Please prepare your account information provided by your Internet Service Provider (ISP). Click Next to begin setup. Note: Quick Setup will allow you to configure a PPPoE connection. For more information on PPPoE and other connection types, please see the Advanced Setup section in this user manual.
Section 6 - Quick Setup The router will automatically perform a PVC scan in order to detect your DSL connection. If the scan is unsuccessful, you must manually enter account settings. For these settings, please refer to your account information provided by your ISP.
Section 6 - Quick Setup When the PVC scan is complete, you will be prompted to enter your username and password as provided by your ISP. Advanced users can configure optional settings on this page. Click Next to continue setup.
Section 6 - Quick Setup The router will automatically verify your username and password.
Section 6 - Quick Setup This page allows you to adjust the Local Area Network settings. No changes are required on this page. Click Next to continue.
Section 6 - Quick Setup Verify your settings are correct and click Save/Reboot. The router will save your settings and reboot itself. Please do not unplug any cables during this process.
Section 7 - Device Info Device Info The Device Info page shows details of the modem such as the version of the software, bootloader, LAN IP address, etc. It also displays the current status of your DSL connection. Summary A summary of your device’s information is provided in this section. The information will reflect your DSL’s connection status.
Section 7 - Device Info WAN The WAN Info screen displays WAN connections previously set up in the Home section. There is an extra “Status” column used for connection status information, displaying either ADSL Link Down or ADSL Link Up.
Section 7 - Device Info Statistics LAN The LAN section shows received and transmitted packet information for the Ethernet interface. Click on Reset Statistics to renew the information. WAN The WAN section shows received and transmitted packet information for the WAN connections that you have set up. Click on Reset Statistics to renew the information.
Section 7 - Device Info ATM The ATM section displays statistical values for your ATM interface as well as for AAL5 and AAL5 VCC. Click on Reset Statistics to reset the values.
Section 7 - Device Info ADSL Information contained in the ADSL screen is useful for troubleshooting and diagnosing connection problems.
Section 7 - Device Info Route The Route Info section displays route information showing the IP addresses of the destination, gateway, and subnet mask as well as other route information.
Section 7 - Device Info ARP This section allows you to query the MAC and IP address information of the equipment attached to the modem.
Section 7 - Device Info DHCP The DHCP server is enabled by default for the router’s Ethernet LAN interface. DHCP service will supply IP settings to computers configured to automatically obtain IP settings that are connected to the router though the Ethernet port. When the router is used for DHCP it becomes the default gateway for DHCP client connected to it. Keep in mind that if you change the IP address of the router, you must change the range of IP addresses in the pool used for DHCP on the LAN.
Section 9 - Advanced Setup Advanced Setup This section of the setup is an advanced version of the quick setup. If you want to make specific configurations to your modem such as creating a SNMP, etc., consider going through this advanced setup for a more comprehensive configuration. WAN Configure the DSL settings as provided by your ISP. Click the Add button if you want to add a new connection for the WAN interface and to proceed to the ATM PVC Configuration screen on the following page.
Section 9 - Advanced Setup ATM PVC Configuration VPI/VCI: These values are required for all DSL connection types and are provided by your ISP. Service Category: Use the default setting unless otherwise instructed by your ISP. Enable QoS: Use the default setting unless otherwise instructed by your ISP. For more information about QoS, see the Quality of Service section in this user manual.
Section 9 - Advanced Setup Connection Type This screen shows the types of network protocols and encapsulation modes that can be configured. Connection Type: Select the connection type that your ISP has instructed to use. • PPP over ATM (PPPoA) • PPP over Ethernet (PPPoE) • MAC Encapsulation Routing (MER)/DHCP • IP over ATM (IPoA) • Bridging PPPoE, MER (also referred to as DHCP) and Bridging are the most common connection types in North America.
Section 9 - Advanced Setup PPP over Ethernet (PPPoE) This page allows you to configure your PPPoE connection. PPP Username: Enter your username as provided by your ISP. PPP Password: Enter your password as provided by your ISP. PPP Service Name: Enter any name that will help you identify your connection. This field will not affect your connection. Dial on demand (with idle timeout timer): Allows you to manually connect to the Internet so you are not permanently connected. Idle timeout timer is included.
Section 9 - Advanced Setup Network Address Translation Settings (PPPoE) Enable NAT: Select if you would like to share your internet connection. Sharing your connection may also require an Ethernet switch to connect multiple computers. Enable Firewall: Select if you would like to utilize the firewall to help protect you from unwanted internet threats. Enable IGMP Multicast: Use the default setting unless otherwise instructed by your ISP. Enable WAN Service: This option is Enabled by default.
Section 9 - Advanced Setup WAN Setup – Summary (PPPoE) Confirm the settings on this page match the settings provided by your ISP. To make any changes, click Back. If your settings are correct, click Save. Note: After clicking Save, you will have to reboot the modem in order to activate your connection.
Section 9 - Advanced Setup MAC Encapsulation Routing (MER) or DHCP This page allows you to configure your MER/DHCP connection. Obtain an IP address automatically: This is the default option. If your ISP has provided you with a static IP address, select Use the following IP address. Enter the IP address and Subnet Mask that your ISP has provided. Obtain default gateway automatically: This is the default option.
Section 9 - Advanced Setup Network Address Translation Settings (MER/DHCP) Enable NAT: Select if you would like to share your internet connection. Sharing your connection may also require an Ethernet switch to connect multiple computers. Enable Firewall: Select if you would like to utilize the firewall to help protect you from unwanted Internet threats. Enable IGMP Multicast: Use default setting unless otherwise instructed by your ISP. Enable WAN Service: This option is Enabled by default.
Section 9 - Advanced Setup WAN Setup – Summary (MER/DHCP) Confirm the settings on this page match the settings provided by your ISP. To make any changes, click Back. If your settings are correct, click Save. Note: After clicking Save, you will have to reboot the modem in order to activate your connection.
Section 9 - Advanced Setup Bridging Enable WAN Service: This option is Enabled by default. Deselecting this option will cause your DSL connection to be disabled. Service Name: Enter any name that will help you identify your connection. This field will not affect your connection. Click Next.
Section 9 - Advanced Setup WAN Setup – Summary (Bridging) Confirm the settings on this page match the settings provided by your ISP. To make any changes, click Back. If your settings are correct, click Save. Note: After clicking Save, you will have to reboot the modem in order to activate your connection.
Section 7 - Device Info LAN You can configure the DSL Modem IP address and Subnet Mask for the LAN interface. The Save button only saves the LAN configuration data, but does not apply the configurations. Select the Save/ Reboot button to save the LAN configuration data, then reboot the modem and apply the new configuration.
Section 7 - Device Info NAT Note: You must enable the NAT service when you configure the WAN connection at first, the NAT item appears in the Advanced Setup directory. In the pure bridging mode, there is no NAT service. Overview - Setting up the NAT Function The DSL router is equipped with the network address translation (NAT) function. With address mapping, several users in the local network can access the Internet via one or more public IP addresses.
Section 7 - Device Info Using port forwarding (the forwarding of requests to particular ports), the router is forced to send requests from the Internet for a certain service, for example, a game, to the appropriate port(s) on the PC on which the game is running. Port triggering is a special variant of port forwarding. Unlike port forwarding, the DSL router forwards the data from the port block to the PC which has previously sent data to the Internet via a certain port (trigger port).
Section 7 - Device Info NAT - Virtual Server Setup By default, DSL router blocks all external users from connecting to or communicating with your network. Therefore, the system is safe from hackers whom may try to intrude into the network and damage it.
Section 7 - Device Info Additionally, port forwarding enables you to redirect traffic to a different port instead of the one to which it was designated. For example, if you have a Web server running on your PC on port 8080 and you want to grant access to this server to any one who accesses DSL router via HTTP. To accomplish this, do as follows: Step 1 Define a port forwarding rule for the HTTP service, with the PC IP or host name. Step 2 Specify 8080 in the Forward to Port field.
Section 7 - Device Info Port Triggering If you configure port triggering for a certain application, you must determine a so-called trigger port and the protocol (TCP or UDP) that this port uses. You then assign the public ports that are to be opened for the application to this trigger port. You can select known Internet services or manually assign ports or port blocks.
Section 7 - Device Info DMZ Host The demilitarized (DMZ) host feature allows one local computer to be exposed to the Internet. This function is applicable for: • Users who want to use a special-purpose Internet service, such as an on-line game or video conferencing program, that is not in the port forwarding list and for which no port range information is available. • Users who are not concerned with security and wish to expose one computer to all services without restriction.
Section 7 - Device Info Security IP Filtering Click Security > IP Filtering and the following interface appears. By default, the firewall is enabled. The firewall is used to block document transmissions between the Internet and your PC. It serves as a security gate and permits only authorized traffic to be sent to the LAN. Note: If the modem is configured to bridge mode only, IP filtering is disabled and the IP filtering interface does not appear.
Section 7 - Device Info Outgoing Click Security > IP Filtering > Outgoing and the following page will appear. By default, all outgoing IP traffic from LAN is allowed, but some IP traffic can be blocked by setting up filters. Click Add and the page for defining the IP filtering rule appears. In this page, you can create a filter rule to identify outgoing IP traffic by specifying a new filter name and at least one condition.
Section 7 - Device Info Incoming Click Security > IP Filtering > Incoming. By default, all incoming IP traffic from the WAN is blocked when the firewall is enabled. However, some IP traffic can be accepted by setting up filters. Click Add, the following page appears. In this page, you can create a filter rule to identify incoming IP traffic by specifying a new filter name and at least one condition. All specified conditions in this filter rule must comply with the rule.
Section 7 - Device Info MAC Filtering Click Security > MAC Filtering. MAC Filtering is only effective on ATM PVCs configured in Bridge mode. Forwarded means that all MAC layer frames are forwarded except those matching any of the specified rules in the following table. Blocked means that all MAC layer frames are blocked except those matching with any of the specified rules in the following table. Click Change Policy and the following page will appear.
Section 7 - Device Info Parental Control Click Security > Parental Control. Click Add and the following page will appear. On this page, you can add time of day restriction to a particular LAN device connected to the Router. The Browser’s MAC Address automatically displays the MAC address of the LAN device where the browser is running. To restrict other LAN device, click Other MAC Address and enter the MAC address of the another LAN device.
Section 9 - Advanced Setup Quality of Service Many communication and multimedia applications require large, high-speed bandwidths to transfer data between the local network and the internet. However, for many applications there is often only one internet connection available with limited capacity. QoS divides this capacity between the different applications and provides undelayed, continuous data transfer in situations where data packets with higher priority are given preference.
Section 9 - Advanced Setup Enabling QoS In this page, you can perform QoS queue management configuration. By default, the system enables QoS and sets a default DSCP mark to automatically mark incoming traffic without reference to particular classifier. Select Advanced Setup > Quality of Service and the following page will appear. Select Enable QoS to enable QoS and set the default DSCP mark. Click Save/Apply to activate QoS.
Section 9 - Advanced Setup QoS Configuration The queuing in packet QoS goes into effect only when a packet is forwarded to a QoS-enabled PVC. Packet forwarding is determined by IP routing or bridging, not under control of the packet QoS. Click Queue Config, and the following page will appear. In this page, you can configure QoS queue. A maximum of 16 entries can be configured. QoS Queue Configuration can allocate four queues.
Section 9 - Advanced Setup Step 1 Click Add, and the following page will appear. Queue Configuration Status: set to enable or disable a QoS queue. Queue: Select a specific network interface. When you have already selected a network interface, the specific network interface selected automatically allocates to the queue. Queue Precedence: Select an integer value for queue precedence. After you select an integer value, the queue entry appropriately places to ingress packets.
Section 9 - Advanced Setup QoS Classification Some applications require specific bandwidth to ensure its data be forwarded in time. QoS classification can creates traffic class rule to classify the upstream traffic. Assign queue which defines the precedence and the interface and optionally overwrite the IP header DSCP byte.
Section 9 - Advanced Setup Traffic Class Name: Enter a name of the class. Rule Order: Select order for queue. Rule Status: Enable or disable this traffic class rule. Assign Classification Queue: Select a classification queue. Assign Differentiated Service Code Point (DSCP) Mark: Select a mark service that modifies the original packet IP header if all rules defined within the classification class are matched.(CS-Mark IP Precedence, AF-Assured Forwarding, EF-Expedited Forwarding) Mark 802.1p if 802.
Section 9 - Advanced Setup wireless port. Protocol: Select one among TCP/UDP TCP UDP or ICMP protocols. Source IP Address Source Subnet Mask UPD/TCP Source Port Destination IP Address Destination Subnet Mask UPD/TCP Destination Port or a Range of Ports Source Mac Address Source Mac Mask Destination Mac Address Destination Mac Mask Set-2 Rules contain the following: 802.1p Priority: the 802.
Section 9 - Advanced Setup QoS-DSCP Setting In order to understand Differentiated Services Code Point (DSCP), you should be familiar with the differentiated services model (Diffserv). Diffserv is a Class of Service (CoS) model that enhances best-effort Internet services by differentiating individual user traffic, service requirements and other criteria.
Section 9 - Advanced Setup Routing Default Gateway In this page, you can modify the default gateway settings. If you select Enable Automatic Assigned Default Gateway, this router can accept the first received default gateway assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s). If the check box is not selected, you must enter the static default gateway and/or a WAN interface. Then, click Save/Apply.
Section 9 - Advanced Setup Static Route In this page you can modify the static route settings. You can query the preset static routes, delete an existing static route, or add a new static route. By default, the system has no static route information. Destination: The IP address to which packets are transmitted. Subnet Mask: The subnet mask of the destination IP address. Gateway: The gateway that the packets pass by during transmission. Interface: The interface that the packets pass through on the modem.
Section 9 - Advanced Setup RIP To activate RIP for the device, select the Enabled radio button for Global RIP Mode. To configure an individual interface, select the desired RIP version and operation, followed by placing a check in the Enabled checkbox for the interface. Click the Save/ Apply button to save the configuration, and to start or stop RIP based on the Global RIP mode selected.
Section 9 - Advanced Setup DNS Server Configuration In this page, you can modify the DNS server settings. If Enable Automatic Assigned DNS is selected, this router accepts the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment. If the checkbox is not selected, enter the primary and secondary (optional) DNS server IP addresses. The interface is as follows. Click Save to save the new configuration.
Section 9 - Advanced Setup Dynamic DNS In this interface, you can modify the Dynamic DNS settings. The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname in any of the many domains, allowing your DSL router to be more easily accessed from various locations on the Internet. Click Add to add Dynamic DNS Add dynamic DNS Enter your information in the spaces provided and click Save.
Section 9 - Advanced Setup DSL The DSL settings page contains modulation and capability settings. Consult your ISP to determine the correct settings. Click Apply if you are finished or click on Advanced Settings if you want to configure other advanced settings.
Section 9 - Advanced Setup Advanced Settings The test mode can be selected from the ADSL Advanced Settings page. Test modes include normal, reverb, medley, no retrain, and L3. After you make your selection, click on Apply to save these settings first before you go to Tone Selection. The frequency band of ADSL is split into 256 separate tones, each spaced 4.3125 kHz apart. Each tone carries separate data, so the modem operates as if 256 separate modems were running in parallel.
Section 9 - Advanced Setup MAC Clone This page allosw you to clone the MAC address on your router. This is needed when adding a router to your network in order to share your internet connection.
Section 10 - Diagnostics Diagnostics The diagnostics screen allows you to run diagnostic tests to check your DSL connection. The results will show test results of two connections: • Connection to your local network • Connection to your DSL service provider Click Run Diagnostic Tests to begin.
Section 11 - Management Management Settings Backup The Backup Settings button allows you to save your router configuration to a file on your computer so that it may be accessed again later. This feature is useful if you have changed the configuration on the router, but would like to revert to a previous configuration. To save your current configuration, click the Backup Settings button. The following pop-up screen will appear with a prompt to open or save the file to your computer.
Section 11 - Management Update To load a previously saved configuration file onto your router, click Browse, select the file on your computer and then click on Update Settings. The router will restore settings and reboot to activate the restored settings.
Section 11 - Management Restore Default Restore Default Settings will delete all current settings and restore the router to factory default settings. Click on the Restore Default Settings button to proceed. The following confirmation dialog will appear confirming your decision to restore default settings. Click on OK to continue.
Section 11 - Management System Log Click View System Log to show the following interface. The system log dialog allows you to view the system log and configure the system log options. Click Configure System Log to show the following interface. You can enable or disable the system log and then select the Log Level, Display Level and Mode, and click Apply to end your configurations. Both the log level and display level have eight choices.
Section 11 - Management System Log Configuration From the configuration screen, set the log to Enable, select the Log Level, Display Level and Mode. If the selected mode is “Remote” or “Both”, events will be sent to a specified IP address and UDP port of a remote system log server. If the selected mode is “Local” or “Both”, events will be recorded and viewed locally. Select the desired values and click Apply to save the system log options.
Section 11 - Management TR-069 Client WAN Management Protocol (TR-069) allows a Auto-Configuration Server (ACS) to perform auto-configuration, provision, collection and diagnostics to this device. If you wish to enable this protocol, then select enable. Contact your ISP to determine the ACS URL, ACS User Name, and ACS Password. You must click on the Save/Reboot button for the change to take place.
Section 11 - Management Internet Time The Time Settings page allows you to automatically synchronize your time with a time server on the Internet. To set the modem’s time, click on the automatically synchronize with Internet time servers checkbox. Additional time settings will appear below the checkbox. Select from the list of NTP (Network Time Protocol) time servers. Then select the time zone that you are in and click Apply to save.
Section 11 - Management Access Control—Services From this page you can enable/disable certain services from passing through your modem. Services that can be enabled/disabled on the LAN/WAN are FTP, HTTP, ICMP, SNMP, Telnet, and TFTP. FTP: (File Transfer Protocol) Used for file transfer. HTTP: (Hyper Text Transfer Protocol) A communications protocol that enables Web browsing. ICMP: (Internet Control Message Protocol) supports packets containing er ror, control, and informational messages.
Section 11 - Management Access Control—IP Address Web access to the modem can be limited when Access Control Mode is enabled. Add the IP address to the IP address list by clicking on the Add button, then select Enabled to enable Access Control Mode. If Access Control Mode is disabled, any workstation connected locally to your modem can access the web interface provided the correct username and password is supplied at log on.
Section 11 - Management Access Control—Passwords Access to your DSL router is controlled through three user accounts: Admin, Support, and User. “Admin” has unrestricted access to change and view configuration. “Support” is used to allowed an ISP technician to access your DSL router for maintenance and to run diagnostics. For “User”, the user name can access the DSL router to view configuration settings, statistics, and update router’s software.
Section 11 - Management Update Software You can update your software through this screen. Follow the screen’s steps. Select Browse to search for your software file and Update Software.
Section 11 - Management Save and Reboot When clicking the Save/Reboot button, it will save all configuration changes made on the modem and restart the device. All new configuration settings will take effect when the modem starts up again.
Section 12 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DSL-520B. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples.) 1. Why can’t I access the web-based configuration utility? When entering the IP address of the D-Link modem (192.168.
Section 12 - Troubleshooting • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Appendix A - Networking Basics Networking Basics Check your IP address After you install your new D-Link device, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless modem) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter. If the address is 0.
Appendix A - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/modem, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® XP - Click on Start > Control Panel > Network Connections. Windows® 2000 - From the desktop, right-click My Network Places > Properties. Step 2 Right-click on the Local Area Connection which represents your D-Link network adapter and select Properties.
Appendix B - Contacting Technical Support Contacting Technical Support U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. Before you contact technical support, please have the following ready: • Model number of the product (e.g. DSL-520B) • Hardware Revision (located on the label on the bottom of the modem (e.g. rev T1)) • Serial Number (s/n number located on the label on the bottom of the modem).
Appendix C - Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Appendix C - Warranty Except as otherwise agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject to the same limitations and exclusions.
Appendix C - Warranty D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
Appendix C - Warranty Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective owners. Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc.
Appendix D - Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.
