Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date Description 1.0 April 24, 2009 DSL-500B Revision A1 with firmware version 1.00 Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
Federal Communication Commission Interference Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Table of Contents Product Overview......................................................... 6 Package Contents.................................................... 6 System Requirements.............................................. 7 Features................................................................... 8 Hardware Overview.................................................... 10 Rear Panel (Connections)...................................... 10 Front Panel (LED Indicators)...............................
Appendix A - Troubleshooting.................................. 79 Troubleshooting...................................................... 79 Appendix B - Networking Basics.............................. 82 Check Your IP Address.................................... 82 Statically Assign An IP Address........................ 83 Appendix C - Technical Specifications.................... 84 Technical Specifications.........................................
Product Overview Package Contents DSL-500B ADSL Router Twisted-Pair Cable (for ADSL) Power Adapter CD-ROM with User Manual Straight-Through CAT5 Ethernet Cable Warning: The Router must be used with the power adapter included with the device. If any of the above items are missing, please contact your reseller.
Product Overview System Requirements ADSL Internet Service Computer With: 200MHz Processor 64MB Memory CD-ROM Drive Ethernet Adapter with TCP/IP Protocol installed Internet Explorer v6 or later, FireFox v1.
Product Overview Features PPP (Point-to-Point Protocol) Security The DSL-500B ADSL Router supports PAP (Password Authentication Protocol), CHAP (Challenge Handshake Authentication Protocol), and MS-CHAP for Point-to-Point Protocol connections. DHCP Support Dynamic Host Configuration Protocol automatically and dynamically assigns all LAN IP settings to each host on your network. This eliminates the need to reconfigure every host whenever changes in network topology occur.
Product Overview Default Routing This allows you to choose a default path for incoming data packets for which the destination address is unknown. This is particularly useful when/if the Router functions as the sole connection to the Internet. ATM (Asynchronous Transfer Mode) The DSL-500B supports Bridged Ethernet over ATM (RFC1483), IP over ATM (RFC1577), and PPP over ATM (RFC 2364). Precise ATM Traffic Shaping Traffic shaping is a method of controlling the flow rate of ATM data cells.
Hardware Overview Rear Panel (Connections) LAN Port Use the Ethernet ports to connect the Router to a computer or an Ethernet LAN. ADSL Port Use the ADSL cable to connect to a compatible telephone line (RJ-11 port). D-Link DSL-500B User Manual Power Button Reset Button To manually reset, depress button with the power on for about five to seven seconds. Push to power-on the Router. Push again to power-off the Router. Power Outlet Use the included adapter to connect the Router to a power source.
Hardware Overview Front Panel (LED Indicators) LED Power Color Green Red LAN Green DSL Green Internet Green Red Status Description Off Power not supplied. On Power is supplied. On During power on self-test, or software update Off No LAN link. Blink Data is being transmitted through the LAN interface. On LAN link is established and active. Off DSL line is disconnected. Blink DSL line is initializing. On DSL line is connected.
Installation Overview This section will walk you through the installation process. Placement of the ADSL Router is very important. Do not place the Router in an enclosed area such as a closet, cabinet, or in the attic or garage. Place the ADSL Router in a location where it can be easily connected to Ethernet devices, the telephone line as well as to a power source. Installation Notes Please read and make sure you understand all the prerequisites for proper installation of your new Router.
Installation Web Browser Any common web browser can be used to configure the Router using the web configuration management software. The program is designed to work best with more recently released browsers such as Opera, Microsoft Internet Explorer® version 6.0, Netscape Navigator® version 6.2.3, or later versions. The web browser must have JavaScript enabled. JavaScript is enabled by default on many browsers.
Installation Information Required from ADSL Service Provider Username This is the Username used to log on to your ADSL service provider’s network. Your ADSL service provider uses this to identify your account. Password This is the Password used, in conjunction with the Username above, to log on to your ADSL service provider’s network. This is used to verify the identity of your account.
Installation VPI Most users will not be required to change this setting. The Virtual Path Identifier (VPI) is used in conjunction with the Virtual Channel Identifier (VCI) to identify the data path between your ADSL service provider’s network and your computer. If you are setting up the Router for multiple virtual connections, you will need to configure the VPI and VCI as instructed by your ADSL service provider for the additional connections.
Installation Information You Will Need About the DSL-500B Username This is the Username needed to access the Router’s management interface. When you attempt to connect to the device through a web browser you will be prompted to enter this Username. The default Username for the Router is admin. This name cannot be changed. Password This is the Password you will be prompted to enter when you access the Router’s management interface. The default Password is admin.
Installation Information You Will Need About Your LAN or Computer Ethernet Network Interface Card (NIC) If your computer has an Ethernet NIC, you can connect the DSL-500B to this Ethernet port using an Ethernet cable. You can also use the Ethernet port on the DSL-500B to connect to other computer or Ethernet device. DHCP Client Status Your DSL-500B ADSL Router is configured to be a DHCP server, by default.
Installation Device Installation The DSL-500B maintains two separate interfaces: ADSL (WAN) and an Ethernet (LAN). Place the Router in a location where it can be easily connected to Ethernet devices, the telephone line, and a power source. The Router can be placed on a shelf or desktop, ideally you should be able to see the LED indicators on the front of the device, should you ever need to view them for troubleshooting. Power On The Router must be used with the power adapter included with the device. 1.
Installation Factory Reset The Router may be reset to the original factory default settings through the following actions. 1. Press and hold the reset button while the device is powered off using a paper clip or similar object. 2. Turn on the power and the router will restart. Observe the Power LED to verify. 3. Wait for 5~8 seconds and then release the reset button. 4. The device settings will be restored to the factory default IP address 192.168.254.254 and the subnet mask is 255.255.255.0.
Installation Network Connections Connect ADSL Line Use the ADSL cable included with the Router to connect it to a telephone wall socket or receptacle. Plug one end of the cable into the ADSL port (RJ-11 receptacle) on the rear panel of the Router and insert the other end into the RJ-11 wall socket. If you are using a low pass filter device, follow the instructions included with the device or given to you by your service provider.
Web Configuration Introduction to Web Configuration The first time you setup the Router. It is recommended that you configure the WAN connection using a single computer, to ensure that both the computer and the Router are not connected to the LAN. Once the WAN connection operates properly, you may continue to make changes to Router configuration, including IP settings and DHCP setup. Web-based Configuration Utility Step 1 Open a web browser such as Internet Explorer on your computer. Step 2 Type 192.168.
Web Configuration Quick Setup This chapter describes the various menus used to configure and monitor the Router, including how to change IP settings and DHCP server setup. Note: When subscribing to a broadband service, you should be aware of the method by which you are connected to the Internet. Your physical WAN device can be Ethernet, DSL, or both.
Web Configuration Setting Up VPI/VCI and QoS After logging in to the DSL router, if no PVC is configured previously and no default settings exist, the Quick Setup webpage will appear This contains some basic configuration that is needed by ATM PVC. The following introduction guides you through the necessary steps to configure your DSL Router. Based on your ISP's instructions, specify the following parameters: VPI (Virtual Path Identifier)- Virtual path between two points in an ATM network.
Web Configuration Selecting the Connection Type and Encapsulation Mode You can select your Internet connection type from the following list.
Web Configuration PPP over ATM (PPPoA) Step 1 In the PVC and its QoS configuration page, configure a PVC and its QoS. Step 2 In the Internet connection type and encapsulation mode page, set the Connection Type to PPP over ATM (PPPoA) and select the desired Encapsulation Mode from the drop-down box and click Next to continue. Step 3 The PPP Username and Password page will appear. Update the following fields and click Next to continue.
Web Configuration Step 4 To use IGMP service on PPPoA PVC, check the Enable IGMP Multicast and the Enable WAN Service box and enter a Service Name. Note: Do not modify the default MTU value setting unless your ISP advises you to change it. Click Next to continue. Step 5 Enter the IP Address and Subnet Mask for the LAN interface. In addition, you can either enable or disable the DHCP server. To enable the DHCP server, enter a start and end IP address, and the Subnet Mask of the Router.
Web Configuration PPPoA Summary This summary window allows you to confirm your PPPoA settings. Click Save/Reboot to save your new PPP over ATM settings and restart the Router.
Web Configuration PPP over Ethernet (PPPoE) Step 1 In the PVC and its QoS configuration page, configure a PVC and its QoS. Step 2 In the Internet connection type and encapsulation type page, set the Connection Type to PPP over Ethernet (PPPoE) and select the Encapsulation Mode from the drop-down box and click Next to continue. Step 3 The PPP Username and Password page will appear. Update the following fields and click Next to continue.
Web Configuration Step 4 To use IGMP service on PPPoE pvc, check the Enable IGMP Multicast and the Enable WAN Service box and enter a Service Name. Note: Do not modify the default MTU value setting unless your ISP advises you to change it. Click Next to continue. Step 5 Enter the IP Address and Subnet Mask for the LAN interface. In addition, you can either enable or disable the DHCP server. To enable the DHCP server, enter a start and end IP address, and the Subnet Mask of the Router.
Web Configuration PPPoE Summary This summary window allows you to confirm your PPPoE settings. Click Save/Reboot to save your new PPPoE settings and restart the Router.
Web Configuration MAC Encapsulation Routing (MER) Step 1 In the PVC and its QoS configuration page, configure a PVC and its QoS. Step 2 In the Internet connection type and encapsulation type page, set the Connection Type to MAC Encapsulation Routing (MER) and select the Encapsulation Mode from the drop-down box and click Next to continue. Step 3 The WAN IP configuration page will appear.
Web Configuration Step 4 To use IGMP service on MER pvc, check the Enable IGMP Multicast box. In the MER mode, you can configure the following functions: Enable NAT Enable Firewall Click Next to continue. Step 5 Enter the IP Address and Subnet Mask for the LAN interface. In addition, you can either enable or disable the DHCP server. To enable the DHCP server, enter a start and end IP address, and the Subnet Mask. You may also choose to change the default value of the lease time.
Web Configuration MER Summary This summary window allows you to confirm your MER settings. Click Save/Reboot to save your new MER settings and restart the Router.
Web Configuration IP over ATM (IPoA) Step 1 In the PVC and its QoS configuration page, configure a PVC and its QoS. Step 2 In the Internet connection type and encapsulation type page, set the Connection Type to IP over ATM (IPoA) and select the Encapsulation Mode from the drop-down box. Click Next to continue. Step 3 The WAN IP configuration page will appear.
Web Configuration Step 4 Click Next and the IPoA IGMP and WAN function configuration page will appear. To use IGMP service on IPoA pvc, check the Enable IGMP Multicast box. In the IPoA mode, you can configure the following functions: Enable NAT Enable Firewall Click Next to continue. Step 5 Enter the IP Address and Subnet Mask for the LAN interface. In addition, you can either enable or disable the DHCP server. To enable the DHCP server, enter a start and end IP address, and the Subnet Mask.
Web Configuration IPoA Summary This summary window allows you to confirm your IPoA settings. Click Save/Reboot to save your new IPoA settings and restart the Router.
Web Configuration Bridging Step 1 In the PVC and its QoS configuration page, configure a PVC and its QoS. Step 2 In the Internet connection type and encapsulation type page, set the Connection Type to Bridging and select the Encapsulation Mode. Click Next to continue. Step 3 The Bridging service configuration page will appear. Select the Enable Bridge Service check box and then enter the Service Name. Click Next to continue.
Web Configuration Bridging Summary This summary window allows you to confirm your Bridge settings. Click Save/Reboot to save your new Bridging settings and restart the Router.
Web Configuration DSL Router Device Information Click Device Info and you can view the following information. Summary WAN Statistics Route ARP DHCP Summary of Device Information Select Summary and the Device Info page will appear. This displays the current status of your DSL connection, including the software version, LAN IP address, and DNS server address. LAN IP Address: This is the management IP address. Default Gateway: In the bridging mode there is no gateway address.
Web Configuration WAN Interface Information Select Device Info > WAN. The WAN Info page will appear. It displays the current status of your WAN connection, depending on the selected connection type. Statistics - LAN Select Device Info > Statistics > LAN. The Statistics-LAN page will appear. This page displays the Router’s LAN statistics. Click Reset Statistics to refresh these statistics. Statistics - WAN Select Device Info > Statistics > WAN. The Statistics-WAN page will appear.
Web Configuration Statistics - ADSL Select Device Info > Statistics > ADSL. The Statistics - ADSL page will appear. This page displays the Router’s ADSL statistics. Click Reset Statistics to refresh these statistics. Click ADSL BER Test to access the ADSL Bit Error Rate Test window. ADSL BER Test The ADSL Bit Error Rate (BER) test determines the quality of the ADSL connection.
Web Configuration Note: If the BER reaches e-5, you cannot access the Internet. Route Table Information Select Device Info > Route. The Device-Route page will appear if the system is in the default configuration. ARP Table Information Select Device Info > ARP. This page displays information on the Address Resolution Protocol (ARP). DHCP Information Select Device Info > DHCP. This page displays the DHCP lease information.
Web Configuration Advanced Setup This chapter includes advanced features used for network management and security as well as administrative tools to manage the Router, view status and other information which is used to examine the performance and for troubleshooting. WAN Configuration Select Advanced Setup > WAN. This page allows you to modify and configure the WAN interface. Note: After a PVC is deleted or modified, the system must be rebooted. Otherwise, the modification does not take effect.
Web Configuration In this page, you can modify VPI/VCI, service categories, and QoS. VPI: Virtual path between two points in an ATM network. Its valid value range is from 0 to 255. VCI: Virtual channel between two points in an ATM network. Its valid value range is from 32 to 65535 (1 to 31 are reserved for known protocols). Service Category: UBR Without PCR/UBR With PCR/CBR/Non Realtime VBR/Realtime VBR. Enable Quality Of Service: Enable or disable QoS.
Web Configuration LAN Configuration Select Advanced Setup > LAN and the Local Area Network (LAN) Setup page will appear. Here you can modify and configure the IP Address, DHCP Server and enable IGMP Snooping. Note: The most convenient way to manage your network is to use the default settings along with the DHCP services. In order to use the Router for DHCP settings, the IP address used for DHCP must be compatible with the IP address of the Router.
Web Configuration NAT Note: You must enable the NAT service when you configure the WAN connection at first. The NAT item will then appear in the Advanced Setup directory. In the pure bridging mode, there is no NAT service. Overview - Setting up the NAT Function The DSL router is equipped with the Network Address Translation (NAT) function. With address mapping, several users in the local network can access the Internet via one or more public IP addresses.
Web Configuration Using port forwarding (the forwarding of requests to particular ports), the router is forced to send requests from the Internet for a certain service, for example, a game, to the appropriate port(s) on the PC on which the game is running. Port triggering is a special variant of port forwarding. Unlike port forwarding, the DSL router forwards the data from the port block to the PC which has previously sent data to the Internet via a certain port (trigger port).
Web Configuration NAT - Virtual Server Setup By default, DSL router blocks all external users from connecting or communicating with your network. Therefore, the system is safe from hackers who may try to intrude into the network and damage it. However, you may want to expose your network to the Internet in limited and controlled ways in order to enable some applications to work from the LAN (for example, game, voice, and chat applications) and to enable Internet access to servers in the home network.
Web Configuration Additionally, port forwarding enables you to redirect traffic to a different port instead of the one to which it was designated. For example, if you have a Web server running on your PC on port 8080 and you want to grant access to this server to any one who accesses DSL router via HTTP. To accomplish this, do as follows: Step 1 Define a port forwarding rule for the HTTP service, with the PC IP or host name. Step 2 Specify 8080 in the Forward to Port field.
Web Configuration Adding Port Forwarding Step 1 To set up virtual servers for a service, go to Advanced Setup > NAT > Virtual Servers, and then click Add. Step 2 Select a service or enter a custom server. Step 3 Set the Server IP Address. Step 4 Enter the server IP address of the computer that provides the service (the server in the local host field). Note that unless an additional external IP address is added, only one LAN computer can be assigned to provide a specific service or application.
Web Configuration Step 9 Click Save/Apply to apply the settings. If the application you require is not in the list, manually enter the information. Select the protocol for the service you are providing from the Protocol drop-down list. Under External Port, enter the port number of the service you are providing. In the Internal Port field, enter the internal port number, to which service requests are to be forwarded. In the Local IP Address field, enter the IP address of the PC that provides the service.
Web Configuration Adding Port Triggering Step 1 To set up port triggering for a service, select Advanced Settings > NAT > Port Triggering, and click Add. Step 2 Select the required application from the Select an application drop-down list, or manually enter the information in the Custom application field. Step 3 Trigger Port Start and Trigger Port End: Enter the port that is to be monitored for outgoing data traffic. Trigger Protocol: Select the protocol that is to be monitored for outgoing data traffic.
Web Configuration DMZ Host The demilitarized military zone (DMZ) host feature allows one local computer to be exposed to the Internet. This function is applicable for: Users who want to use a special-purpose Internet service, such as an on-line game or video conferencing program, that is not in the port forwarding list and for which no port range information is available. Users who are not concerned with security and wish to expose one computer to all services without restriction.
Web Configuration Adding a DMZ Host Step 1 To set up a PC as a DMZ host, select Advanced Setup > NAT > DMZ Host. Step 2 Enter the local IP address of the PC that is to be enabled as an exposed host. Step 3 Click Save/Apply to apply the settings. Remove DMZ host Step 1 Clear the DMZ Host Address. Step 2 Click Save/Apply to apply the settings.
Web Configuration Security Select Advanced Setup > Security > IP Filtering. The Outgoing IP Filtering Setup page will appear. By default, the firewall is enabled. The firewall is used to block data transmissions between the Internet and your PC. It serves as a security gate and permits only authorized traffic to be sent to the LAN. Click Add to create an IP Filter Rule.
Web Configuration Outgoing IP Filtering Setup In this page, you can create a filter rule to identify outgoing IP traffic by specifying a new filter name and at least one condition. All specified conditions in the filtering rule must comply with the rule to take effect. Click Save/Apply to save and activate the filter. Incoming IP Filtering Setup Select Security > IP Filtering > Incoming. The Incoming IP Filtering Setup page will appear.
Web Configuration MAC Filtering Setup Select Security > MAC Filtering, and the MAC filtering Setup page will appear. MAC Filtering is only effective on ATM PVCs configured in Bridging mode. FORWARDED means that all MAC layer frames are forwarded except those matching with any of the specified rules in the following table. BLOCKED means that all MAC layer frames are blocked except those matching with any of the specified rules in the following table.
Web Configuration For example, to forbid the PC whose MAC address is 00:13:20:9E:0F:10 through PPPoE dial-up, begin with the following page. Click Add to configure the interface as follows. Click Save/Apply and the MAC Filtering Setup page will appear.
Web Configuration Parental Control Click Security > Parental Control. The Time of Day Restrictions page will appear. Click Add to configure the Time of Day Restriction. In this page, you can add time of day restriction to a special LAN device connected to the Router. The Browser's MAC Address automatically displays the MAC address of the LAN device where the browser is running. To restrict another LAN device, click Other MAC Address and enter the MAC address of the another LAN device.
Web Configuration Quality of Service Many communication and multimedia applications require large, high-speed bandwidths to transfer data between the local network and the internet. However, for many applications there is often only one internet connection available with limited capacity. QoS divides this capacity between the different applications and provides undelayed, continuous data transfer in situation where data packets with higher priority are given preference.
Web Configuration QoS Queue Configuration The queuing in packet QoS becomes effective only when packet is forwarded to QoS-enabled PVC. Packet forwarding is determined by IP routing or bridging, not under control of the packet QoS. Select Advanced Setup > Queue Config. In this page, you can configure QoS queue. A maximum of 24 entries can be configured. QoS Queue Configuration can allocate four queues.
Web Configuration Step 1 This page allows you to configure a QoS queue entry and then assign it a specific network interface. Queue Configuration Status: Set to enable or disable a QoS queue. Queue: Select a specific network interface. When you have already selected a network interface, the specific network interface selected automatically allocates to the queue. Queue Precedence: Select an integer value for queue precedence.
Web Configuration QoS Classification Some applications require specific bandwidth to ensure its data be forwarded in time. QoS classification can creates traffic class rule to classify the upstream traffic. Assign queue which defines the precedence and the interface and optionally overwrite the IP header DSCP byte. After QoS classification, QoS divides capacity between different applications and provides undelayed, continuous data transfer where data packet with higher priority is given preference.
Web Configuration Select Advanced Setup > QoS Classification. In this page, you can configure network traffic classes. Click Add to create a traffic class rule to classify the upstream traffic. Traffic Class Name: Enter a name of the class. Rule Order: Select order for queue. Rule Status: Enable or disable this traffic class rule. Assign Classification Queue: Select a classification queue.
Web Configuration Set-1 rules contain the following: Physical LAN Port: Select one among USB port, Ethernet ports and wireless port. Protocol: Select one among TCP/UDP TCP UDP or ICMP protocols. Source IP Address Source subnet mask UPD/TCP Source Port Destination IP Address Destination Subnet Mask UPD/TCP destination port or a range of ports Source Mac Address Source Mac Mask Destination Mac Address Destination Mac Mask Set-2 rules contain the following: 802.1p Priority: the 802.
Web Configuration QoS-DSCP Setting In order to understand what is differentiated services code point (DSCP), you should be familiar with the differentiated services model (Diffserv). Diffserv is a class of service (CoS) model that enhances best-effort Internet services via differentiating traffic by users, service requirements and other criteria.
Web Configuration For example, mark each transmitted ICMP packet which passes traffic to 0-35class with an appropriate DSCP (CS1). After proper modifications, click Save/Apply and the following page will appear. Click Save/Apply. This configuration takes effective at once.
Web Configuration QoS-802.1p Setting The IEEE 802.1p priority marking method is a standard for prioritizing network traffic at the data link/Mac sub-layer 802.1p traffic is simply classified and sent to the destination, with no bandwidth reservations established. The follow diagram shows the structure of 802.1Q Frame. The 802.1Q header includes a 3-bit prioritization field, which allows packets to be grouped to be grouped into eight levels of priority (0-7), where level 7 is the highest one.
Web Configuration Routing Select Advanced Setup > Routing. The Routing - Default Gateway page will appear. Routing - Default Gateway In this page, you can modify the default gateway settings. If you select Enable Automatic Assigned Default Gateway, this router can accept the first received default gateway assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s). If the check box is not selected, you must enter the static default gateway and/or a WAN interface. Then, click Save/Apply.
Web Configuration Routing - Static Route On this page you can modify the static route settings. You can query the preset static routes, delete an existing static route, or add a new static route. By default, the system has no static route information. Click Add and the following page will appear. Enter the destination network address, subnet mask, gateway AND/OR available WAN interface, then click Save/Apply to add the entry to the routing table.
Web Configuration DNS In this interface, you can modify the Dynamic DNS settings. The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname in any of the many domains, allowing your DSL router to be more easily accessed from various locations on the Internet. DNS Server Select Advanced Setup > DNS. The DNS Server Configuration page will appear.
Web Configuration DSL Select Advanced Setup > DSL. The DSL Settings page will appear. The available settings include G.Dmt/ G.lite/ T1.413/ ADSL2/ AnnexL/ ADSL2+/ AnnexM / Inner pair / Outer pair / Bitswap / SRA. The Router can negotiate the modulation mode with the DSLAM. Click Advanced Settings to select the DSL test mode. In the DSL Advanced Settings page select the desired DSL test mode and then click Apply. Click Tone Selection to modify the upstream and downstream tones.
Web Configuration Diagnostics Click Diagnostics to show the interface. Your modem is capable of testing your DSL connection. The individual tests are listed below. If a test displays a fail status, click Rerun Diagnostic Tests at the bottom of this page to make sure the fail status is consistent. If the test continues to fail, click Help and follow the troubleshooting procedures. Management The Management features an array of options designed to help you get the most out of your Router.
Web Configuration System Log Select Management > System Log. The System Log page will appear. The system log interface allows you to view the system log and configure the system log options. Click Configure System Log and the System Log - Configuration page will appear. Here, you can enable or disable the system log and select the Log Level, Display Level and Mode. Click Save/Apply to save your changes. Both the log level and display level have eight choices.
Web Configuration After configuring the System Log options, click View System Log to query the system logs. In this example, the View System Log displays the default values. Note: The log and display of the system events are above the set level. If you intend to record all information, you must set the levels as Debugging. Click Refresh to refresh the system event logs or click Close to exit from this interface. System Agent Select Management > SNMP Agent. The SNMP - Configuration page will appear.
Web Configuration TR-069 Client Select Management > TR-069 Client. The TR-069 client - Configuration page will appear. Select the desired values and click Save/Apply to configure the TR-069 Client options. Internet Time Select Management > Internet Time and the Time Settings page will appear. Note: When the PVC is PPPoE connection, the Internet Time option will appear in the Management directory. This window allows you to set the Router’s time configuration. Click Save/Apply to save your changes.
Web Configuration Access Control Access Control – Services Select Management > Access Control > Services. In this interface, you can enable or disable HTTP, ICMP, SSH, TELNET and TFTP services. And the LAN and WAN side can have different configuration. Note: If the connection is PPPoE PVC, you can view the information on WAN side. Access Control - IP Address Select Management > Access Control > IP Address. The Access Control - IP Address page will appear.
Web Configuration Access Control - Passwords Select Access Control > Passwords to change the password of the Router. Update Software Select Management > Update Firmware. In this page, you can update the Router's firmware. Click Browse to find the file and click Update Firmware to update. Note: Do not turn off your Router during firmware updates. When the update is finished, the Router reboots automatically. Do not turn off your modem either before the reboot is over.
Appendix A - Troubleshooting Troubleshooting This chapter provides solutions to problems that might occur during the installation and operation of the DSL-500B. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples.) 1. How do I configure my DSL-500B Router without the CD-ROM? Connect your PC to the Router using an Ethernet cable. Open a web browser and type http://192.168.254.254.
Appendix A - Troubleshooting 3. What can I do if my Router is not working correctly? Here are a few steps that you can follow to resolve the issue: Follow the directions highlighted in question 2 to reset the Router. Check if all the cables are firmly connected at both ends. Check the LEDs on the front of the Router. The Power indicator, DSL and LAN indicators should be illuminated. Please ensure that the settings in the Web-based configuration manager, e.g.
Appendix A - Troubleshooting 4. What can I do if my router can’t be detected by the installation CD? Ensure the Router is powered on. Check if all the cables are firmly connected at both ends and all the LEDs are working correctly. Ensure that only one network interface card on your PC is activated. Disable Windows Firewall. In Windows XP, go to Start > Control Panel and then double-click Security Center. Disable the Windows Firewall setting and click OK.
Appendix B - Networking Basics Networking Basics Check Your IP Address After you install your new D-Link adapter, the TCP/IP settings, by default should be set to Obtain an IP address from a DHCP server automatically. To verify your IP address, please follow the steps below. Click Start > Run. In the run box type cmd and click OK. At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter. If the address is 0.0.0.
Appendix B - Networking Basics Statically Assign An IP Address If you are not using a DHCP capable gateway/router, or if you need to assign a static IP address, please follow the steps below: Step 1 Windows® XP: Click Start > Control Panel > Network Connections. Windows® 2000: From the desktop, right-click My Network Places > Properties. Step 2 Right-click on Local Area Connection that represents your D-Link network adapter and select Properties.
Appendix C - Technical Specifications Technical Specifications ADSL Standards ANSI T1.413 Issue 2 ITU G.992.1 (G.dmt) AnnexA ITU G.992.2 (G.lite) Annex A ITU G.994.1 (G.hs) ITU G.992.5 Annex A ADSL2 Standards ITU G.992.3 (G.dmt.bis) Annex A ITU G.992.4 (G.lite.bis) Annex A ADSL2+ Standards ITU G.992.5 (ADSL2+) Data Transfer Rate G.dmt full rate downstream: up to 8 Mbps / upstream: up to 1Mbps G.lite: ADSL downstream up to 1.5 Mbps / upstream up to 512Kbps G.dmt.
