DSL-500 ADSL Router User’s Guide Second Edition (April 2001) 6DSL500...
DSL-500 ADSL Router User’s Guide Wichtige Sicherheitshinweise 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den spätern Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. 5.
DSL-500 ADSL Router User’s Guide THE DATED PURCHASE INVOICE) MUST BE PROVIDED. IF PURCHASER'S CIRCUMSTANCES REQUIRE SPECIAL HANDLING OF WARRANTY CORRECTION, THEN AT THE TIME OF REQUESTING RMA NUMBER, PURCHASER MAY ALSO PROPOSE SPECIAL PROCEDURE AS MAY BE SUITABLE TO THE CASE.
DSL-500 ADSL Router User’s Guide Trademarks Copyright 2000 D-Link Corporation. Contents subject to change without prior notice. D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective proprietors. Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems Inc.
TABLE OF CONTENTS PREFACE.................................................................................................................VII THIS USER’S GUIDE ........................................................................................................................................... VII Overview of the User’s Guide ....................................................................................................................... vii INTRODUCTION TO THE ROUTER ...........................
FIRST TIME SET UP ................................................................................................ 30 CONFIGURE THE MANAGER PC FOR DHCP ....................................................................................................... 31 ACCESS THE WEB-BASED MANAGER ................................................................................................................. 33 CONFIGURE THE WAN CONNECTION ..............................................................................
DSL-500 ADSL Router User’s Guide Preface Thank you for choosing the DSL-500 ADSL Router. The DSL-500 will provide your private small office or home network with convenient Internet access and rapid download speeds while improving network efficiency and security. D-Link strives to provide cost effective broadband access devices that are easy to use and upgrade for small office and home networks.
DSL-500 ADSL Router User’s Guide Chapter 5 Web-based Management – Describes how to use the web-based manager and discusses the management options available. Chapter 6 LAN Setup – Discusses different options for IP addressing on your LAN. Describes how to change the IP address of the LAN interface on the Router. Chapter 7 Using the Console Manager- Describes how to use the console manager and lists the most commonly used commands, including how to change the password used to access the web-based manager.
DSL-500 ADSL Router User’s Guide 1 Introduction to the Router This chapter describes the Router and it features and includes an introduction to ADSL technology. Diagrams are provided detailing the hardware and LED indicators. A list of package contents is presented at the end of the chapter. Router Description and Operation The DSL-500 ADSL Router is designed to provide a simple, cost-effective and secure ADSL Internet connection for your small- to medium-sized private network.
DSL-500 ADSL Router User’s Guide video gaming, without experiencing any loss of quality or disruption of voice/fax telephone capabilities. ADSL provides a dedicated service over a single telephone line operating at speeds of up to 8 Mbps downstream (to the user) and up to 640 Kbps upstream depending on local telephone line conditions. These conditions are ideal for many user applications.
DSL-500 ADSL Router User’s Guide Static Routing This allows you to select a data path to a particular network destination that will remain in the routing table and never “age out”. If you wish to define a specific route that will always be used for data traffic from your LAN to a specific destination within your LAN (for example to another router or a server) or outside your network (to a ISP defined default gateway for instance).
DSL-500 ADSL Router User’s Guide Standards Compatability and Compliance The DSL-500 complies with or is compatible with the following standards as recognized by their respective agencies. ♦ ITU G.994.1 (G.Hs Auto-handshake) compliant ♦ ITU G.992.1 (G.dmt Full-rate ADSL) compliant ♦ ITU G.992.2 (G.lite “Splitterless ADSL”) compliant ♦ ITU-T Rec. I.361 compliant ♦ ITU-T Rec. I.610 compliant ♦ Compatible with all T1.
DSL-500 ADSL Router User’s Guide Front Panel Place the Router in a location that permits an easy view of the LED indicators shown in the front panel diagram below. Front Panel Rear Panel The rear panel of the Router provides access to the AC power adapter cord connection as well as the port connections.
DSL-500 ADSL Router User’s Guide LED Indicators LED Indicators The LED Indicators read as follows: Power Steady green light indicates the unit is powered on. Status Lights steady green during the ADSL negotiation phase. Once the connection status has been settled, the light will blink green. ADSL: Link Steady green light indicates a valid ADSL connection. This will light after the ADSL negotiation process has been settled. ADSL: Act Blinking green light indicates an active wan session.
DSL-500 ADSL Router User’s Guide Verify Package Contents Open the box and carefully remove all items. In addition to this Installation Guide, make sure that you have: 5 3 1 ADSL Cable 2 4 6 1. One DSL-500 ADSL Router 2. One AC power adapter suitable for your electric service 3. One RS-232 (DB-9 to DB-9) cable for console connection 4. One ADSL telephone cable with RJ-11 connectors for ADSL connection (standard telephone wire) 5. One DSL-500 tool kit on CD-ROM 6.
DSL-500 ADSL Router User’s Guide 2 Prepare for Installation For the smoothest possible installation, assemble all the equipment and information needed to set up the Router and establish the initial ADSL connection before you begin. Everything needed for the installation is listed and discussed in this chapter. Microfilters and Splitters Most ADSL clients will be required to install a simple device that prevents the ADSL line from interfering with regular telephone services.
DSL-500 ADSL Router User’s Guide Microfilters Unless you are instructed to use a “line splitter” (see below), it will be necessary to install a microfilter (low pass filter) device for each telephone or telephone device (answering machines, Faxes etc.) that share the line with the ADSL service. Microfilters are easy-to-install, in-line devices, which attach to the telephone cable between the telephone and wall jack. Microfilters that install behind the wall plate are also available.
DSL-500 ADSL Router User’s Guide Line Splitter If you are instructed to use a “line splitter”, you must install the device between the Modem and the phone jack. Use standard telephone cable with standard RJ11 connectors. The splitter has three RJ-11 ports used to connect to the wall jack, the Modem and if desired, a telephone or telephone device. The connection ports are typically labeled as follows: Line - This port connects to the wall jack. ADSL – This port connects to the Modem.
DSL-500 ADSL Router User’s Guide Additional Requirements You will need a PC (referred to in this guide as the Manager PC) to set up and use the Router. In addition, it will be necessary to configure the device using information provided by your ADSL service provider. This information is used to establish the parameters of the ADSL connection and identify the Router on the WAN. The requirements for the PCs on your LAN are summarized below.
DSL-500 ADSL Router User’s Guide CONNECTION METHOD It is necessary to know the connection method used for the ADSL connection. The connection method is also known as the ADSL Protocol, Encapsulation Protocol or Encapsulation Method. These protocols are defined by “RFCs” which are internationally recognized standards for networking protocols. You will be required to configure the Router to use the correct method. PPP connections require account information to be entered and stored in the device.
DSL-500 ADSL Router User’s Guide BRIDGED ETHERNET CONNECTIONS (RFC 1483) For Bridged Ethernet connections it will be necessary to give the Router a global IP address and default gateway. Global IP Address If the connection method used is Ethernet over ATM (RFC 1483), a unique global IP address will be needed for the Router. The assigned global IP address must be entered only if the connection method used is Ethernet over ATM (RFC 1483).
DSL-500 ADSL Router User’s Guide 3 Hardware Installation This chapter discusses the various connections you will need to make in order to use the Router. When selecting the location for the Router, allow room to access the connections on the rear panel. You will want to place the Router so that you will be able to see the LED indicators on the front panel. Also allow some space above the Router for ventilation to avoid problems with overheating.
DSL-500 ADSL Router User’s Guide straight-through (MDI-X) connection. Follow standard Ethernet guidelines when deciding what type of cable to use to make this connection. Use a normal crossed cable when connecting the Router to a normal (MDI-X) port on a switch or hub. Use a straight-through cable when connecting it to an uplink (MDI-II) port on a hub or switch. When connecting the Router directly to a PC or server (MDI-II) use a straight-through cable.
DSL-500 ADSL Router User’s Guide Connect Server or PC to Router The Router may be connected directly to a server or PC using the RJ-45 Ethernet port. The diagram below illustrates a PC/Server to Router connection with the Router being employed as a firewall.
DSL-500 ADSL Router User’s Guide 4 First Time Set Up It will be convenient for most users to establish an initial ADSL connection for one PC equipped with an Ethernet NIC (Network Interface Card). It is recommended that you install and configure the Router using one non-networked computer. This allows you to verify that the ADSL service is functioning and that you are able to communicate with the device.
DSL-500 ADSL Router User’s Guide Configure the Manager PC for DHCP Use the following steps to configure the manager PC to be a DHCP client. These same steps must be performed for every host PC on your network if you use the DHCP function of the Router. 7. In Windows 95/98, click on the START button, go to Settings and choose Control Panel. 8. In the Control Panel window, double-click on the Network icon.
DSL-500 ADSL Router User’s Guide 9. Under the Configuration tab, select the TCP/IP component and click Properties. 10. Choose the Obtain an IP address automatically option and click OK. 11. Restart the PC to let the new setting take effect.
DSL-500 ADSL Router User’s Guide Access the Web-based Manager The Manager PC can now use a web browser to communicate with the Router. Be sure that the Manager PC is not configured to use a proxy server for Internet access. Note: Be sure that the Manager PC is not configured to use a proxy server in the Internet settings. In Windows Internet Explorer, you can check if a proxy server is enabled using the following procedure: 1. In Windows, click on the START button, go to Settings and choose Control Panel.
DSL-500 ADSL Router User’s Guide NOTE: Do not confuse the user name and password used to access the web-based manager with the ADSL account user name and password needed for PPP connections to access the ADSL or network service provider’s network. Logging in will bring up the main page of the web-based management module. Click the DSL-500 folder in the main window. This folder will open revealing the management menu options.
DSL-500 ADSL Router User’s Guide PPPoE Connections The default connection method used by the Router is Point-to-Point-Protocol over Ethernet (PPPoE) as defined in RFC 2516. In the PPPoE Configuration window (shown below) you must to enter the VPI and VCI values, as well as the user name and password for network account authentication and verification. When this information is entered, the changes must be saved and the Router restarted. Follow these steps to establish the PPP and ADSL network connection: 1.
DSL-500 ADSL Router User’s Guide Changing the Connection Type The default connection method used by the Router for the WAN connection is PPP over Ethernet. If you wish to use this method you do not need to change this setting. However if you plan to use a static IP address for a “Bridged Ethernet” (RFC 1483) connection, or PPP over ATM (RFC 2364) you must select those protocols in this window.
DSL-500 ADSL Router User’s Guide PPPoA Connections Although the protocols differ significantly, from the viewpoint of the ADSL client, there is little difference between the two variations of PPP connections. The values that must be entered for PPPoA connections are the same as those you would enter for PPPoE connections. To configure the Router using for a PPPoA connection, follow the instructions below. 1.
DSL-500 ADSL Router User’s Guide RFC 1483 Bridged Ethernet Connections To configure the Router for RFC 1483 connections it is necessary to provide a static global IP address and subnet mask for the WAN interface. In addition, you may need to define the DNS settings as well. Ask your network service provider about DNS configuration settings. You can enter the DNS settings in the DHCP Configuration menu. DHCP Configuration is discussed in Chapter 5, Web-based Management.
DSL-500 ADSL Router User’s Guide Changing the User Name and Password Before you configure the Router and connect to the WAN you should change the user name and password used to access the web-based manager. Click on the User Name and Password button in the main menu. User Name and Password Window Type the new User Name and Old Password in their respective fields. Type the New Password and confirm it in the Confirm New Password field and click the OK button.
DSL-500 ADSL Router User’s Guide When the Restart System window appears, click the Restart button. Restart System Window Connect to WAN Once you have configured the Router, saved changes and restarted it, you can connect the manager PC to the Internet. The procedure is the same for PPPoE and PPPoA connections. Connect with PPP (PPPoE and PPPoA) If you have enabled the Connect on Demand feature, the Router will have established the WAN connection upon restarting.
DSL-500 ADSL Router User’s Guide 5 Web-based Management The DSL-500 offers a web-based (HTML) graphical user interface allowing users to manage the Router from anywhere on the network using a standard browser, software such as Netscape Navigator or Microsoft Internet Explorer. The web browser is used for direct communication with the Router using HTTP protocol. Your browser window may not appear exactly with the screen captures (pictures) in this guide.
DSL-500 ADSL Router User’s Guide In the page that opens, click on the Login to web-based management module button: Login Button A new window will appear and you will be prompted for a user name and password. Use default user name admin and password admin for first time set up. User Login Logging in will bring up the main page of the web-based management module. Click the D-Link DSL-500 folder located below the D-Link logo in the upper lefthand corner.
DSL-500 ADSL Router User’s Guide Change User Name and Password Before you configure the Router and connect to the WAN you should change the user name and password you just used to access the web-based manager. You can change these by clicking on the User Name and Password button in the main menu. User Name and Password Window Use this window to change the User Name and Password used to access the web-based manager. Type the new User Name and Old Password in their respective fields.
DSL-500 ADSL Router User’s Guide Connection Configuration To establish the WAN connection, the Router must be configured to suit the requirements of the ADSL connection protocol. This section discusses how to configure the Router for the various connection types. Most ADSL clients will use the default method PPPoE, discussed below.
DSL-500 ADSL Router User’s Guide PVC Use this field to assign the VPI and VCI values for the Router. These numbers are given to you by your DSL service provider and must be entered in order to establish the ADSL connection. PPPoE Login Use this field to assign a Login User Name and Password used for authentication by your network service provider. Type in the user name and password in their respective fields. You can use any combination of up to 64 characters (no spaces) in both fields.
DSL-500 ADSL Router User’s Guide Connection Type Connection Type Window (PPPoE) The default connection method used by the Router for the WAN connection is PPP over Ethernet. If you wish to use this method you do not need to change this setting. However if you are using a static IP address (also called “Bridged Ethernet” encapsulation as defined by RFC 1483), or PPP over ATM (RFC 2364) you can select them here.
DSL-500 ADSL Router User’s Guide Static IP Address Configuration (for RFC 1483) Static IP Address Configuration Window In the Static IP Address configuration window enter the static IP Address and subnet mask assigned by your network service provider for your WAN interface. The Static IP Address is a globally unique IP address used to identify the Router on the Internet. If you are given a Default Gateway IP address enter that here as well.
DSL-500 ADSL Router User’s Guide PPPoA Configuration PPPoA Configuration PVC Use this field to assign the VPI and VCI values for the Router. These numbers are given to you by your DSL service provider and must be entered in order to establish the ADSL connection. PPPoA Login Use this field to assign a Login User Name and Password used for authentication by your network service provider. Type in the user name and password in their respective fields.
DSL-500 ADSL Router User’s Guide If your network account is not billed according to the amount of time connected, the Idle Time field should be left at the default value 0. This means that the Router is always connected and able to connect on demand. If your network account is billed according to the amount of time the Router is actually connected to the Internet, enter an appropriate Idle Time value (in seconds).
DSL-500 ADSL Router User’s Guide Line Condition Line Condition In the Line Condition window you can monitor the characteristics of the ADSL connection and confirm that it has been established. From here you can observe various performance statistics of each end of the connection, including: Data Path: Displays the current data path type, Fast or Interleaved. Operation Mode: Describes the of modulation technique used to make the ADSL connection.
DSL-500 ADSL Router User’s Guide Router Functions The DHCP and NAT functions of the Router allows the network manager to more easily manage IP addresses and subnets, and enhance network security by presenting only one global IP address to the Internet. This section discusses how to use these conventional routing functions. DHCP The Dynamic Host Configuration Protocol (DHCP) allows the Router to assign IP addresses to all properly configured hosts on the network.
DSL-500 ADSL Router User’s Guide Netmask This mask informs the client, how the destination IP address is to be divided into network, subnet, and host parts. The netmask has ones in the bit positions in the 32-bit address which are to be used for the network and subnet parts, and zeros for the host part. Default Gateway This specifies the Gateway IP Address that will be assigned to and used by the DHCP clients.
DSL-500 ADSL Router User’s Guide Port Redirection to allow appropriate use of your servers by outside users. See the section on Port Redirection for more information. For the purposes of network administration, NAT is almost indispensable. Hosts and servers on the internal network can be moved easily. Using NAT together with DHCP can greatly reduce the workload of a network manager while allowing tremendous flexibility. NAT Configuration Window The NAT function is enabled by default on the Router.
DSL-500 ADSL Router User’s Guide Security Features Network security is an unfortunate necessity for any network connected to the Internet. Protection of sensitive information and proprietary assets on your private network should be designed into the network infrastructure from the beginning. If you are not already, it is recommended that you become familiar with network security issues and the strategies available to help reduce risks from outside as well as from within your LAN.
DSL-500 ADSL Router User’s Guide Advanced Filtering and Firewall (Screen #1) To define the filter rule sets, click on the Advanced Filtering and Firewall button to bring up the first window. Choose Enable in the IP Filter pull-down menu and click the OK button to enable IP filtering. Then click on the set number you wish to configure to proceed to the next window.
DSL-500 ADSL Router User’s Guide Advanced Filtering and Firewall (Screen #2) In the second Advanced Filtering window you can supply a comment or name of up to 15 characters for the set in the Set Comments field. Click the OK button to save the comments, then click on the number of the subset you want to configure to proceed to the next window.
DSL-500 ADSL Router User’s Guide Advanced Filtering and Firewall (Screen #3) In the third Advanced Filtering window you will define the rule applied for the chosen subset. Again you can supply a name for the subset in the Comment field and click the box on the right to enable the Filter Rule. In the Pass or Block field select the action to be performed on the IP packets, the default is Pass Immediately. All blocked packets will be dropped.
DSL-500 ADSL Router User’s Guide in either the Source or Destination row. If there is no port specified in the Start Port column, the filter rule will be ignored. Use the <, >, = or ≠ in the pull down menu to specify the port or range of ports to be filtered.
DSL-500 ADSL Router User’s Guide Redirect Port Window The Redirect Port window presents five entry fields. The first field, Comment can be used to assign an appropriate name to the new route, for our example we will use the name HTTP Server. In the Internet Port field enter the designated TCP or UDP protocol port number for the particular protocol packet you wish to redirect. In our example an incoming HTTP packets use port 80. The local port is the port used by the designated host on the LAN.
DSL-500 ADSL Router User’s Guide Save Changes In order to save the configuration changes that have been made to the Router you must save them to the Router’s non-volatile RAM. You can change any or all of the configurable settings in one session before you initiate the saving procedure. If you experience a power loss or reboot the Router before saving, all changes will have to be reset. Save Changes Window When you are ready to save the settings, click the Save Configuration button.
DSL-500 ADSL Router User’s Guide Update Firmware In order to keep pace with changes in ADSL standards and technology the DSL-500 allows you to easily update the embedded firmware. You may obtain the latest version of the DSL-500 firmware by logging onto the D-Link web site at www.dlink.com. If you are connected to the Internet, you can access the D-Link web site by clicking on the blue URL in the Update Firmware window.
DSL-500 ADSL Router User’s Guide Summary Statistics Click on the Summary button for a concise presentation of various Router statistics. Summary This page provides summary statistics of the various features of the Router. The list includes: PPPoE Login, PPPoE Information (when using PPPoE connection method), PVC, Connection Method, DHCP Configuration and NAT Configuration.
DSL-500 ADSL Router User’s Guide 6 LAN Setup The Router allows many possibilities for network layout. This gives the network administrator much flexibility to decide how best to use it. One of the most important decisions for the network administrator involves IP addressing on the LAN. The easiest choice in most cases is to let the Router take care of it for you using DHCP, which is done by default. This chapter discusses the various alternatives for IP address assignment using the Router.
DSL-500 ADSL Router User’s Guide Default Addressing Example Host IP Address Subnet Mask Gateway IP Router 192.168.0.1 255.255.255.0 Computer #1 192.168.0.2 255.255.255.0 192.168.0.1 Computer #2 192.168.0.3 255.255.255.0 192.168.0.1 Computer #3 192.168.0.4 255.255.255.0 192.168.0.1 Please note that when using the default IP address as in the above example, the first three numbers in the IP address must always be the same with only the fourth number changing (for a Class C network).
DSL-500 ADSL Router User’s Guide Connect a standard RS-232 (DB-9 to DB-9) cable to the Router’s RS-232 port on the rear panel, connect the other end to a PC with a terminal emulation program already installed. Power on the Router and launch the emulation program. The terminal emulator will display system information while the unit undergoes selftesting. When 192.168.0.1> appears on the screen the unit has completed its self-test. In this mode, the default IP address 192.168.0.
DSL-500 ADSL Router User’s Guide HyperTerminal Interface with new IP address You must save the new IP address by typing the command series config save and pressing Enter. This will save the new IP address for the Router and store it in the device’s flash memory. You may now disconnect the terminal emulator and access the device using the web-based management interface for configuration. For more thorough instructions on using the out-of-band console manager, see Chapter 7.
DSL-500 ADSL Router User’s Guide 7 Using the Console Manager Settings for the Router can be configured via the RS-232 console port connection using terminal emulation software such as Microsoft HyperTerminal included with Microsoft’s operating systems. This chapter lists and describes a few of the most essential command sets that might be used by the typical user. This chapter is not intended to be a complete list of the commands available.
DSL-500 ADSL Router User’s Guide To see a list of available commands and command syntax along with brief explanation of the command, type help all and depress Enter. Remember that the console interface commands are case sensitive. Typing any of the commands listed above and depressing Enter will put the console interface into that command mode. For example, form the IP address prompt type ip and depress Enter. This will put the interface into “ip” where it can now accept ip mode commands.
DSL-500 ADSL Router User’s Guide A Technical Specifications General Standards: ITU G.992.1 (G.dmt) ITU G.992.2 (G.lite) ITU G.994.1 (G.Hs) ITU-T Rec. I.361 ITU-T Rec. I.610 IEEE 802.3 IEEE 802.3u IEEE 802.
DSL-500 ADSL Router User’s Guide General Media Interface Exchange: RJ-11 port ADSL telephone line connection RJ-45 port for 10BASET Ethernet connection RS-232 (DB9 female) console port for local configuration Physical and Environmental DC inputs: Input: 120V AC 60Hz 24W Power Adapter: Output: 12V DC 1.0 A Power Consumption: 10 Watts (max) Operating Temperature: 0° to 40° C (32° - 104° F) Humidity: 5 to 95% (non-condensing) Dimensions: 215 mm x 163 mm x 45 mm Weight: 455 gm (1 lb.
DSL-500 ADSL Router User’s Guide B IP Concepts This appendix describes some basic IP concepts, the TCP/IP addressing scheme and show how to assign IP Addresses. When setting up the Router, you must make sure it has a valid IP address. Even if you will not use the WAN port (ADSL port), you should, at the very least, make sure the Ethernet LAN port is assigned a valid IP address. This is required for telnet, in-band SNMP management, and related functions such as “trap” handling and TFTP firmware download.
DSL-500 ADSL Router User’s Guide Networks attached to the Internet are assigned class types that determine the maximum number of possible hosts per network. The previous figure illustrates how the net and host portions of the IP address differ among the three classes. Class A is assigned to networks that have more than 65,535 hosts; Class B is for networks that have 256 to 65534 hosts; Class C is for networks with less than 256 hosts.
DSL-500 ADSL Router User’s Guide The network portion of an IP address will be referred to in this manual as a network number; the host portion will be referred to as a host number. To connect to the Internet or to any private IP network that uses an Internetassigned network number, you must obtain a registered IP network number from an Internet-authorized network information center.
DSL-500 ADSL Router User’s Guide C DSL-500 Firmware Upgrade Utility You can update system firmware using the DSL-500 Firmware Upgrade Utility. To upgrade the Router’s firmware you must have installed this software on the PC you wish to use for this purpose. Install the utility by clicking the file titled setup.exe located on the Installation CD-ROM. It will be installed automatically.
DSL-500 ADSL Router User’s Guide Enter the password and click OK. In the new window you will see the MAC address of the Router and the IP address of the PC you are using. The PC and the Router must be on the same subnet for the upgrade to be completed. The upgrade utility will suggest a new IP address to be temporarily assigned to the device during the firmware upgrade procedure.
Offices AUSTRALIA D-LINK AUSTRALASIA Unit 16, 390 Eastern Valley Way, Roseville, NSW 2069, Australia TEL: 61-2-9417-7100 FAX: 61-2-9417-1077 TOLL FREE: 1800-177-100 (Australia), 0800-900900 (New Zealand) URL: www.dlink.com.au E-MAIL: support@dlink.com.au, info@dlink.com.au CANADA D-LINK CANADA 2180 Winston Park Drive, Oakville, Ontario L6H 5W1 Canada TEL: 1-905-829-5033 FAX: 1-905-829-5223 BBS: 1-965-279-8732 FREE CALL: 1-800-354-6522 URL: www.dlink.ca FTP: ftp.dlinknet.com E-MAIL: techsup@dlink.
JAPAN D-LINK JAPAN 10F, 8-8-15 Nishi-Gotanda, Shinagawa-ku, Tokyo 141 Japan TEL: 81-3-5434-9678 FAX: 81-3-5434-9868 URL: www.d-link.co.jp E-MAIL: kida@d-link.co.jp RUSSIA D-LINK RUSSIA Michurinski Prospekt 49, 117607 Moscow, Russia TEL: 7-095-737-3389, 7-095-737-3492 FAX: 7-095-737-3390 E-MAIL: vl@dlink.ru SINGAPORE D-LINK INTERNATIONAL 1 International Business Park, #03-12 The Synergy, Singapore 609917 TEL: 65-774-6233 FAX: 65-774-6322 URL: www.dlink-intl.com E-MAIL: info@dlink.com.sg S.
Registration Card Print, type or use block letters. Your name: Mr./Ms__________________________________________________________________________ Organization: ____________________________________________Dept.
