Table of Contents Table of Contents Product Overview........................................................................................ 3 Package Contents............................................................................................ 3 System Requirements..................................................................................... 4 Introduction....................................................................................................... 5 Features........................
Section 1 - Product Overview Product Overview Package Contents • DSL-2740R Wireless N ADSL2+ Modem Router • 2 non-detachable Antennas (MIMO 2x2) • Power Adapter • CD-ROM with Installation Wizard, User Manual, and Special Offers • One twisted-pair telephone cable used for ADSL connection • One straight-through Ethernet cable • One Quick Installation Guide Note: Using a power supply with a different voltage rating (12 V/ 1 A) than the one included with the DSL-2740R will cause damage and void the warranty
Section 1 - Product Overview System Requirements • ADSL Internet service • Computer with: • 200MHz Processor • 64 MB Memory • CD-ROM Drive • Ethernet Adapter with TCP/IP installed • Windows 7/Vista/XP/2000 • MAC OS • Internet Explorer 6 or higher, FireFox 1.
Section 1 - Product Overview Introduction High-Speed ADSL2/2+ Internet Connection Latest ADSL2/2+ standards provide Internet transmission speeds of up to 24 Mbps downstream and 1 Mbps upstream.* High-Performance Wireless Embedded 802.11n technology for high-speed wireless connection, complete compatibility with 802.11b/g wireless devices. Total Security Firewall protection from Internet attacks, user access control, WPA/WPA2 wireless security.
Section 1 - Product Overview Features • Faster Wireless Networking - The DSL-2740R provides a wireless connection of up to 300 Mbps* with other 802.11n wireless clients. This capability allows users to fully participate in real-time activities online, such as video streaming, online gaming, and real-time audio. • Compatible with 802.11b and 802.11g Devices - The DSL-2740R is still fully compatible with the IEEE 802.11b and g standards, so it can connect with existing 802.
Section 1 - Product Overview Hardware Overview Connections RESET BUTTON To manually reset the device, depress the button with the power on for between ten and fifteen seconds. ADSL PORT Use the ADSL cable to connect to your telephone line (RJ-11 port). FOUR ETHERNET PORTS Use the Ethernet ports to connect the router to your Ethernet LAN or Ethernet devices. D-Link DSL-2740R WIRELESS ON/OFF SWITCH Turns wireless function on or off.
Section 1 - Product Overview Hardware Overview LEDs POWER A steady green light indicates the unit is powered on. When the device is powered off, this is dark. DSL A steady green light indicates a valid ADSL connection. This will light after the ADSL negotiation process has been settled. A blinking green light indicates activity on the WAN (ADSL) interface. WLAN A steady green light indicates a wireless connection. A blinking green light indicates activity on the WLAN.
Section 2 - Installation Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage. Before you Begin Please read and make sure you understand all the prerequisites for proper installation of your new router. Have all the necessary information and equipment on hand before beginning the installation.
Section 2 - Installation Installation Notes In order to establish a connection to the Internet it will be necessary to provide information to the router that will be stored in its memory. For some users, only their account information (Username and Password) is required. For others, various parameters that control and define the Internet connection will be required. You can print out the two pages below and use the tables to list this information.
Section 2 - Installation 802.11 Wireless LAN Configuration All the 802.11 wireless LAN settings may be configured on a single page using the web-based manager. For basic wireless communication you need to decide what channel to use and what SSID to assign. These two settings must be the same for any wireless workstations or other wireless access point that communicate with the DSL-2740R through the wireless interface. Security for wireless communication can be accomplished in a number of ways.
Section 2 - Installation Information you will need from your ADSL service provider Username This is the username used to log on to your ADSL service provider’s network. It is commonly in the form user@isp.co.uk. Your ADSL service provider uses this to identify your account. Password This is the password used, in conjunction with the Username above, to log on to your ADSL service provider’s network. This is used to verify the identity of your account.
Section 2 - Installation VPI Most users will not be required to change this setting. The Virtual Path Identifier (VPI) is used in conjunction with the Virtual Channel Identifier (VCI) to identify the data path between your ADSL service provider’s network and your computer. If you are setting up the router for multiple virtual connections, you will need to configure the VPI and VCI as instructed by your ADSL service provider for the additional connections.
Section 2 - Installation Information you will need about the DSL-2740R Username This is the username needed to access the router’s management interface. When you attempt to connect to the device through a web browser you will be prompted to enter this username. The default username for the router is “admin.” The user cannot change this. Password This is the password you will be prompted to enter when you access the router’s management interface. The default Password is “admin.” The user may change this.
Section 2 - Installation Information you will need about your LAN or computer Ethernet NIC If your computer has an Ethernet NIC, you can connect the DSL-2740R to this Ethernet port using an Ethernet cable. You can also use the Ethernet ports on the DSL-2740R to connect to other computers or Ethernet devices. DHCP Client status Your DSL-2740R ADSL Router is configured, by default, to be a DHCP server.
Section 2 - Installation Wireless Installation Notes DSL-2740R lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness, and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business.
Section 2 - Installation Device Installation The DSL-2740R Wireless ADSL Router maintains three separate interfaces: an Ethernet LAN, a wireless LAN and an ADSL Internet (WAN) connection. Carefully consider the router’s location’s suitability for connectivity for your Ethernet and wireless devices. You must have a functioning broadband connection via a bridge device such as a Cable or ADSL modem in order to use the router’s WAN function.
Section 2 - Installation Factory Reset Button The router may be reset to the original factory default settings by using a ballpoint or paperclip to gently push down the reset button in the following sequence: 1. Press and hold the reset button while the device is powered off. 2. Turn on the power. 3. Wait for 10~15 seconds and then release the reset button. Remember that this will wipe out any settings stored in flash memory including user account information and LAN IP settings.
Section 2 - Installation Hub or Switch to Router Connection Connect the router to an uplink port (MDI-II) on an Ethernet hub or switch with a straight-through cable as shown in this diagram. If you wish to reserve the uplink port on the switch or hub for another device, connect to any of the other MDI-X ports (1x, 2x, etc.) with a crossed cable.
Section 3 - Configuration Configuration This section will show you how to configure your new D-Link wireless router using the web-based configuration utility. Web-based Configuration Utility Connect to the router To configure the WAN connection used by the router it is first necessary to communicate with the router through its management interface, which is HTML-based and can be accessed using a web browser.
Section 3 - Configuration Setup Wizard This chapter is concerned with using your computer to configure the WAN connection. The following chapter describes the various windows used to configure and monitor the router including how to change IP settings and DHCP server setup. ADSL SETUP Click on Setup Wizard to launch the Setup Wizard. WELCOME TO D-LINK SETUP WIZARD There are four steps for configuring your router. Click on Next to continue.
Section 3 - Configuration STEP 1: CHANGE YOUR DSL-2740R PASSWORD The default password is admin. In order to secure your network, please modify the password. Note: The Confirm Password entry must be the same as that for New Password. Of course, you can click on Skip to ignore the step. STEP 2: SET TIME AND DATE TIME SETTING: Please enable Automatically synchronize with Internet time servers if you want to use the time server.
Section 3 - Configuration Daylight Saving time starts in the European Union on the last Sunday of March. Thus, in the European Union, you must select March, Last, Sunday. The time must depend on your country’s time zone. For example, in Germany you must type 2 because Germany’s time zone is 1 hour ahead of GMT or UTC (GMT+1). Thus, in Germany you must select March, Last, Sunday, at 1:00 A.M. Daylight Saving time ends in most parts of the United States on the first Sunday of November.
Section 3 - Configuration STEP 3: SELECT INTERNET CONNECTION TYPE Please select your Country and ISP Provider from the list. If you cannot find the country and ISP in the list; you can select Others, and then input the VPI and VCI and Connection Type. Please enter the VPI/VCI numbers if provided by the ISP. Click on Next to save the configuration and continue. Please enter your Username and Password provided by your ISP provider. Click on Next to go to the next Setup Wizard window.
Section 3 - Configuration STEP 4: CONNECT TO INTERNET Click on APPLY to save the configuration.
Section 3 - Configuration Internet Setup To access the INTERNET SETUP (WAN) settings window, click on the INTERNET SETUP button in the SETUP directory and select Manual Setup to configure the MANUAL ADSL interface on this page: INTERNET SETUP If you want to type connection configuration for various types, please enable Manual Setup. MANUAL ADSL CONNECTION SETUP PPPoE/PPPoA Choose this option if your ISP uses PPPoE/PPPoA.
Section 3 - Configuration For PPPoE/PPPoA connection Type the Username and Password (and PPPoE Service Name, if required by your ISP). Type the service name from your ISP in Servername. Choose PPPoE LLC/Snap-Bridging, PPPoE VC-mux, PPPoA LLC/ encapsulation or PPPoA VC-mux in Connection Type. Type the MTU value which you want (it should be less than 1492) in MTU. Set the time for which if your data doesn’t pass through the connection, it will be disconnected in Idle Time Out.
Section 3 - Configuration Type the PVC values which are from your ISP in VPI/VCI. Select Enable NAT when you want to have WAN and LAN. Select Enable Firewall when you want to have the basic filter function, for example, ICMP ping to DSL-2740R. Select Enable IGMP Proxy when you want to let IAD act as a IGMP proxy which can help the proxy server to send IGMP query packets to the IPTV clients. Click on Apply to save the configuration.
Section 3 - Configuration Wireless Use this section to configure the wireless settings for your D-Link router. Please note that changes made in this section will also need to be duplicated onto your wireless clients and PC. To access the WIRELESS (WLAN) settings window, click on Wireless Setup in the SETUP directory. Wireless Network Setting Click on Wireless Connection Setup Wizard to set up the wireless connection in an easy way.
Section 3 - Configuration Clicking on Wireless Connection Setup Wizard will open the D-Link Wireless Security Setup Wizard. Enable Your Wireless Network Your wireless network is enabled by default. You can simply uncheck the Enable Your Wireless Network checkbox to disable wireless. Network Name (SSID) identifies members of the Service Set. Accept the default name or change it to something else. If the default SSID is changed, all other devices on the wireless network must also use the same SSID.
Section 3 - Configuration On this page, you can check the Wireless Status, Network Name (SSID), Wireless Security Mode, and Pre-shared Key. Click Prev to go back to the previous page. Click Save to save the configuration and return to the main menu of the Wireless Setup page. Click Cancel to return to the main menu of the Wireless Setup page. Add Wireless Device with WPS Clicking on Add Wireless Device with WPS will open the D-Link Add Wireless Device with WPS (Wi-Fi Protected Setup) Wizard.
Section 3 - Configuration Add Wireless Device with WPS (Automatically) This page allows you to select the PIN or PBC method for WPS connection. PIN- Enter the PIN code from your wireless device and click Connect to start the handshaking. PBC- Click Connect on your wireless device and press the Connect button on your wireless device within 120 seconds to start the handshaking. Click Prev to go back to the previous page.
Section 3 - Configuration Add Wireless Device with WPS (WI-FI PROTECTED SETUP) Wizard It will show the wireless login information. You can check if it is correct, then click Next. Manual WIRELESS Connection Setup SETTINGS Clicking on Manual Wireless Connection Setup on the Wireless Setup page will take you to the Manual Wireless Connection Setup page. Click on Enable Wireless to allow the router to operate in the wireless environment. The SSID identifies members of the Service Set.
Section 3 - Configuration Channel Width The maximum rate for 20 MHz/GI=0 is 130 Mbps. The maximum rate for 40 MHz/GI=1 is 300Mbps. Transmission Rate It is suggested that you keep the Best (automatic) selection. This is related to Receive Sensitivity as follows, for example: MCS 0 MCS 1 MCS 2 MCS 3 MCS 4 MCS 5 MCS 6 MCS 7 MCS 8 MCS 9 MCS 10 MCS 11 MCS 12 MCS 13 MCS 14 MCS 15 MANRATE 0x80 0x81 0x82 0x83 0x84 0x85 0x86 0x87 0x88 0x89 0x8a 0x8b 0x8c 0x8d 0x8e 0x8f HT20/GI=0 6.5 Mbps 13 Mbps 19.
Section 3 - Configuration WIRELESS SECURITY Mode To protect your privacy you can configure wireless security features. This device supports three wireless security modes including WEP, WPA, and WPA-Personal. WEP is the original wireless encryption standard. WPA provides a higher level of security. WPA-Personal does not require an authentication server.
Section 3 - Configuration WIRELESS SECURITY MODE - WEP WEP (Wireless Encryption Protocol) encryption can be enabled for security and privacy. WEP encrypts the data portion of each frame transmitted from the wireless adapter using one of the predefined keys. The router offers 64 or 128 bit encryption with four keys available. Select WEP Key Length from the drop-down menu. (128 bit is stronger than 64 bit.) Specify the encryption key from the Current Network Key drop-down menu.
Section 3 - Configuration WIRELESS SECURITY MODE – WPA-Personal Use WPA or WPA2 mode to achieve a balance of strong security and best compatibility. This mode uses WPA for legacy clients while maintaining a higher level of security with stations that are WPA2 capable. Also the strongest cipher that the client supports will be used. For best security, use WPA2 Only mode. This mode uses AES (CCMP) cipher and legacy stations are not allowed access with WPA security. For maximum compatibility, use WPA Only.
Section 3 - Configuration Local Network You can configure the LAN IP address to suit your preference. Many users will find it convenient to use the default settings together with DHCP service to manage the IP settings for their private network. The IP address of the router is the base address used for DHCP. In order to use the router for DHCP on your LAN, the IP address pool used for DHCP must be compatible with the IP address of the router.
Section 3 - Configuration ADD/EDIT DHCP RESERVATION (OPTIONAL) Click on the Add button under the DHCP Reservations List. Select Enable to let you reserve the IP Address for the designated PC with the configured MAC Address. The Computer Name can help you recognize this PC with the MAC Address by assigning it a name like “Father’s Laptop.” Click on Copy Your PC’s MAC Address to help you get the Mac address from the PC you are using to browse the web page. Click on Apply to save the configuration.
Section 3 - Configuration Time The TIME configuration option allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the NTP (Network Time Protocol) Server. Daylight Saving can also be configured to automatically adjust the time when needed. To access the TIME setting window, click on the Time and Date button in the SETUP directory. TIME Check Enable NTP Server.
Section 3 - Configuration Daylight Saving time ends in most parts of the United States on the first Sunday of November. Each time zone in the United States must use Daylight Saving time at 2:00 A.M. Thus, in the United States you must set November, First, Sunday, at 2:00 A.M as your end time. Daylight Saving time ends in the European Union on the last Sunday of October. For instance, in Germany you must type 2 because Germany’s time zone is 1 hour ahead of GMT (GMT+1).
Section 3 - Configuration Logout The LOGOUT page enables you to log out of your router configuration and closes the browser. To access the LOGOUT setting window, click on Logout in the SETUP directory LOGOUT Click on Logout to log out of the router configuration and close the browser.
Section 3 - Configuration Advanced This chapter includes the more advanced features used for network management and security as well as administrative tools to manage the router, view status, and other information used to examine performance, and for troubleshooting. Port Forwarding Use the PORT FORWARDING window to open ports in your router and re-direct data through those ports to a single PC on your network (WANto-LAN traffic).
Section 3 - Configuration Application Rules Use this feature as parental controls to only grant or block access from applications such as peer-to-peer utilities or games . APPLICATION RULES Select Allow or Deny for applications such as ICQ, MSN, Yahoo messenger, and Real Audio/Video. Click Apply Settings to save the configuration.
Section 3 - Configuration Inbound Filter By default, all incoming IP traffic from the Internet is allowed. The Inbound Filter allows you to create a filter rule to filter incoming IP traffic by specifying a filter name and at least one condition. All of the specified conditions in this filter rule must be satisfied for the rule to take effect. ADD INBOUND IP FILTER Type the filter name in the Filter Name field. Choose ICMP, TCP/UDP, TCP, or UDP in Protocol.
Section 3 - Configuration IP/Mac Filter This is the ability to set filters in the router and re-direct data through those to a single PC on your network. SELECT IP/MAC FILTER RULE INDEX Choose Both, Incoming, or Outgoing in Direction. Type the Source IP address, Subnet Mask, and Port Number. Type Destination IP address, Subnet Mask, and Port Number. Choose ICMP, TCP, or UDP in Protocol. Click Save to add the policy in the list.
Section 3 - Configuration DNS Setup The DNS is used to resolve the DNS name to IPs. You can type the DNS name or obtain it automatically. The Dynamic DNS feature allows you to host a server (Web, FTP, Game Server, etc.) using a domain name that you have purchased (for example: www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses.
Section 3 - Configuration DDNS CONFIGURATION Please access a DDNS web server to obtain a domain name. You can use the D-Link DDNS server at https://www.dlinkddns.com to receive a free DDNS. Please enable Enable Dynamic DNS if you want to use DDNS. Choose which DDNS web site to use in Server Address. Type the Host name which you registered with your DDNS service provider in Host Name. Type the username/password on the Username/Password/Verify Password of your DDNS account.
Section 3 - Configuration Firewall & DMZ The router already provides a simple firewall by virtue of the way NAT works. By default NAT does not respond to unsolicited incoming requests on any port, thereby making your WAN invisible to Internet cyber attackers. DMZ means Demilitarised Zone. DMZ allows computers behind the router firewall to be accessible to Internet traffic. Typically, your DMZ would contain Web servers, FTP servers, and others.
Section 3 - Configuration DMZ SETTINGS Please select Enable DMZ and type the DMZ client IP in the DMZ IP Address. Or you also can choose the DMZ host using the pulldown menu. Click on Apply Settings to apply these settings.
Section 3 - Configuration Advanced Wireless These options are for users who wish to change the performance of their 802.11g wireless radio from the standard settings. D-Link does not recommend changing the factory default settings. Incorrect settings may impair the performance of your wireless radio. The default settings should provide the best wireless radio performance in most environments.
Section 3 - Configuration GUEST WIRELESS SETTINGS Select how many SSIDs you need in Wireless SSID Num. Please select Enable Wireless Guest Network. Type SSID in Guest SSID1. Click on Apply Settings to apply these settings.
Section 3 - Configuration Wi-Fi Protected Setup Wi-Fi Protected Setup is used to easily add devices to a network using a PIN or button press. Devices must support Wi-Fi Protected Setup in order to be configured by this method. If the PIN changes, the new PIN will be used in following the Wi-Fi Protected Setup process. Clicking on Cancel will not reset the PIN. However, if the new PIN is not saved, it will get lost when the device reboots or loses power.
Section 3 - Configuration Advanced LAN These options are for users that wish to change the LAN settings. D-Link does not recommend changing these settings from factory default. Changing these settings may affect the behavior of your network. UPNP Please select Enable UPnP when you want to have Universal Plug and Play (UPnP) support peer-to-peer Plug and Play functionality for network devices. MULTICAST STREAMS Please click on Enable Multicast Streams (IGMP) to let a IGMP stream pass through DSL-2740R.
Section 3 - Configuration Maintenance Click on the MAINTENANCE tab to view the window buttons for various functions located in this directory. Password The factory default password of this router is admin. To help secure your network, D-Link recommends that you choose a new password. SET PASSWORD (OPTIONAL) Please type the Current Password, New Password, and Confirm Password. Please click Apply Settings to save the settings.
Section 3 - Configuration Save/Restore Settings Once the router is configured, you can save the configuration settings to a configuration file on your hard drive. You also have the option to load configuration settings or restore the factory default settings. SAVE/RESTORE CONFIGURATION Please click Save next to Save Settings to Local Hard Drive. Please click Browse to choose the configurations file and then click Update Settings to upload the file.
Section 3 - Configuration Firmware Update Use the FIRMWARE UPGRADE window to load the latest firmware for the device. Note that the device configuration settings may return to the factory default settings, so make sure you first save the configuration settings in the SAVE/RESTORE SETTINGS window described in the previous page. To access the FIRMWARE UPGRADE setting window, click Firmware Update under the MAINTENANCE tab. It shows Current Firmware Version and Current Firmware Date.
Section 3 - Configuration Diagnostics Your router is capable of testing your DSL connection. The individual tests are listed below. If a test displays a fail status, click Re-run Diagnostics Tests at the bottom of this page to make sure the fail status is consistent. If the test continues to fail, click Help and follow the troubleshooting procedures. SYSTEM CHECK There are two tests: Test your Ethernet(1-4) Connection and Test ADSL Synchronization. They will either show PASS or FAIL.
Section 3 - Configuration System Log The System Log allows you to configure local, remote and email logging, and to view the logs that have been created. This section allows you to view the logs.
Section 3 - Configuration Status Click on the STATUS tab to reveal the window buttons for various functions located in this directory. The DEVICE STATUS window is the first item in the STATUS directory. Use these windows to view system information and monitor performance. Device Info The Device Info page displays a summary overview of your router status, including the device software version and summary of your Internet configuration (both wireless and Ethernet status).
Section 3 - Configuration INTERNET STATUS This window displays WAN information including IP address, Mask, Default Gateway, Preferred, and Alternate DNS Server. WIRELESS LAN This window displays authenticated wireless stations and their status.
Section 3 - Configuration LOCAL NETWORK INFO This window displays LAN information including MAC, IP address, Subnet Mask, and DHCP Server.
Section 3 - Configuration Connected Clients This page shows the connected DHCP clients on the LAN. NUMBER OF DYNAMIC DHCP CLIENTS This window displays all the entities which have linked to the LAN interface successfully.
Section 3 - Configuration Statistics This information reflects the current status of your router. WAN STATISTICS This window displays all the Receiver and Transmitted packet statistics and status on the WAN interface. LAN STATISTICS This window displays all the Receiver and Transmitted packet statistics and status on the LAN interface.
Section 3 - Configuration ADSL STATISTICS This window displays the ADSL statistics.
Section 4 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DSL-2740R. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples.) 1. Why can’t I access the web-based configuration utility? When entering the IP address of the D-Link router (192.
Section 4 - Troubleshooting • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click on the Internet Options Icon. From the Security tab, click on the button to restore the settings to their defaults. • Click on the Connection tab and set the dial-up option to Never Dial a Connection. Click on the LAN Settings button. Make sure nothing is checked. Click on the OK. • Go to the Advanced tab and click on the button to restore these settings to their defaults.
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Appendix A - Wireless Basics Wireless Local Area Network (WLAN) In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point as seen in the picture, the signal can travel up to 300 feet.
Appendix A - Wireless Basics Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations like: Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers. Wireless network is easy to setup, but if you’re installing it for the first time it could be quite a task not knowing where to start. That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.
Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click on the OK. At the prompt, type ipconfig and press Enter. This will display the IP address, subnet mask, and the default gateway of your adapter.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® 7 - Click on Start > Control Panel > Network Connections. Windows® Vista - Click on Start > Control Panel > Network Connections. Windows® XP - Click on Start > Control Panel > Network Connections. Windows® 2000 - From the desktop, right-click on My Network Places > Properties.
Appendix C - Contacting Technical Support Technical Specifications ADSL Standards • ANSI T1.413 Issue 2 • ITU G.992.1 (G.dmt) AnnexA • ITU G.992.2 (G.lite) Annex A • ITU G.994.1 (G.hs) • ITU G.992.5 Annex A ADSL2 Standards • ITU G.992.3 (G.dmt.bis) Annex A • ITU G.992.4 (G.lite.bis) Annex A Protocols • IEEE 802.
