D-Link DSL-2640B Wireless ADSL2/2+ 4-port Ethernet Router (for ToT) User Manual Building Networks for People RECYCLABLE 2007/06/25
Table of Contents GENERAL INFORMATION .......................................................................... 3 Package Contents ........................................................................ 3 Important Safety Instructions.......................................................... 3 Front Panel View ......................................................................... 4 Back Panel View ..........................................................................
Wireless—MAC Filter .............................................................58 Wireless—QoS .....................................................................59 TOOLS ..........................................................................................60 Access Control ...........................................................................60 Access Control—Admin ..........................................................61 Access Control—Services .............................................
General Information The D-Link DSL-2640B is an ADSL2+ router that provides a convenient wireless routing function. This user manual offers you with a simple and easy-to-understand format to install and configure your router.
Front Panel View LED Power Status DSL WLAN LAN 1-4 Mode Indication Solid Green No light Red Flashing Green Solid Green No Light Slow Flashing Fast Flashing Solid Green Flashing No Light Solid Green Flashing Green The router is powered on. (READY) The power is off. Failure or device malfunction. (NOT READY) Traffic is passing through the device. (INTERNET TRAFFIC) DSL is synchronized. No carrier signal. DSL attempting synch. Trying to detect carrier signal.
Back Panel View Port Description On/ Off Power Press to turn the router on and off. Connects to the power adapter. Press for less than 3 seconds to reset the router. Press for 3 seconds or more to revert to factory settings. For use by D-Link service personnel for maintenance purposes only. RJ-45 connects the unit to Ethernet devices such as a PC or a switch. RJ-11 telephone port connects telephone cable to telephone or fax machine.
Connecting the Router to Your Computer Power Input Reset Button LAN 1-4 Console * DSL Port On / Off Button * Console—for use by D-Link repair service personnel only. Connect the Telephone Cable • Connect one end of the telephone cable to the DSL port on the router and the other end of the cable into the wall socket.
Configuring the Router To use your web browser to access the web pages used to set up the router, your computer must be configured to “Obtain an IP address automatically”, that is, you must change the IP network settings of your computer so that it is a DHCP client. If you are using Windows XP and do not know how to change your network settings, skip ahead to Appendix A and read the instructions provided. Open your web browser and enter the URL http://192.168.1.1 in the address bar and press Enter.
After you log into the router, the first screen will be the Quick Setup screen which requires you to enter the PPP Username and Password. Click on Save/Reboot or click on Advance Setup to go directly to the main user interface.
Home The home section provides configurations for general use, including a Quick Setup Wizard with steps to quickly set up your router for Internet connection. Also included in this section are LAN / WAN setup and DNS configuration. The below sections explains the setup for each. Wizard This section will explain how to quickly configure the router if your only intention is to access the Internet.
10
Connection Type Following is the Connection Type screen where you select the type of network protocol and encapsulation mode over the ATM PVC that your ISP has instructed you to use. The following is a PPPoA example. Click on Next to continue.
PPP Username and Password Now, enter the PPP username and password as given by your ISP. Then decide if you will be using any features such as Dial on demand, PPP IP extension, Keep Alive and then click on Next. Network Address Translation Settings The next step is to configure the Network Address Translation (NAT) settings. For the example, NAT will be enabled. The remaining fields are left as default and then click on Next to continue.
Device Setup You can configure the DSL Router IP address and Subnet Mask for the LAN interface to correspond to your LAN’s IP Subnet. If you want the DHCP server to automatically assign IP addresses, then enable the DHCP server and enter the range of IP addresses that the DHCP server can assign to your computers. Disable the DHCP server if you would like to manually assign IP addresses. Click on Next to continue.
Wireless The router’s wireless function can be enabled on the following screen. If the function is enabled, then continue by entering the SSID, the wireless network name. Click on Next to continue.
Setup - Summary After all of the configurations are done, the WAN Setup Summary screen displays all WAN settings that you have made. Check that the settings are correct before clicking on the Save / Reboot button. Clicking on Save / Reboot will save your settings and restart your router.
Wireless Wireless -- Basic The below Wireless – Basic screen lets you enable or disable wireless. The default setting for wireless is enabled. You can also hide the access point so others cannot see your ID on the network. Click on Apply to save your configurations before clicking on Security to continue to the Security configurations.
Wireless – Security The next screen is the Wireless – Security screen which allows you to select the network authentication method and to enable or disable WEP encryption. Note that depending on the network authentication that is selected, the screen will change accordingly so additional fields can be configured for the specific authentication method. Network authentication methods include the following— • Open—anyone can access the network. The default is a disabled WEP encryption setting.
WAN Configure the WAN settings as provided by your ISP. Click on the Add button if you want to add a new connection for the WAN interface and to proceed to the ATM PVC Configuration screen as seen below. The ATM PVC Configuration screen allows you to configure an ATM PVC identifier (VPI and VCI) and select a service category.
Find out the following values from your ISP before you change them. • • • • VPI: Virtual Path Identifier. The valid range is 0 to 255. VCI: Virtual Channel Identifier. The valid range is 32 to 65535. Service Category: Five classes of traffic are listed— o UBR Without PCR (Unspecified Bit Rate without Peak Cell Rate)— UBR service is suitable for applications that can tolerate variable delays and some cell losses.
The following screen shows the below types of network protocols and encapsulation modes— • • • • • PPP over ATM (PPPoA) PPP over Ethernet (PPPoE) MAC Encapsulation Routing (MER) IP over ATM (IpoA) Bridging If you will be using VLAN tagging, then click on the Enable 802.1q checkbox and then enter the VLAN ID number. Note that the 802.1q function is only available if you select PPPoE, MER, or Bridging. When finished with your selections, click on Next to continue.
The following screen allows you to enter PPP username and password as well as make any selections regarding your connection. • • • • Dial on demand: Allows you to manually connect to the Internet so you are not permanently connected. Idle timeout timer is included. PPP IP extension: Used by some ISP’s. Check with your ISP to see if it is required. Keep alive: Keeps you connected to your ISP even when no activity is present for a certain period of time.
When finished, click on Next to proceed to the NAT Settings screen. • • • • Enable NAT: Select enable if you wish to share one WAN IP address for multiple computers on your LAN. Enable Firewall: Select if you wish to enable the router’s firewall for security. Enable IGMP Multicast: Select enable if you wish to be able to provide multicasts, mostly used in video streaming. Enable WAN Service: Select if you wish to use WAN service and then set the service name.
Click Next when finished with your configurations and the below screen will follow displaying the WAN settings that you made. When satisfied with the settings click on the Apply button.
After you apply the configurations, it will return to the WAN Setup screen showing the new configurations. Select the Finish button to save the changes and reboot the router. Below is the DSL Router Reboot screen that will appear during the rebooting process.
LAN You can configure the DSL Router IP address and Subnet Mask for the LAN interface. An available option if you will be multicasting is IGMP snooping, for which you can also select standard or blocking mode. If you want the DHCP server to automatically assign IP addresses, enable DHCP server and enter the range of IP addresses that DHCP server can assign. Disable DHCP server if you would like to manually assign IP addresses.
DNS DNS Server Configuration Use the DNS Server screen to request automatic assignment of a DNS or to specify a primary and secondary DNS. If you uncheck the Enable Automatic Assigned DNS checkbox, two additional fields— primary and secondary DNS server—will appear. Enter the information and click on Apply to save the configuration.
Dynamic DNS Dynamic DNS is a service for allowing an Internet domain name to be assigned to a varying IP address. This makes it possible for other sites on the Internet to establish connections to you without needing to track the IP address themselves. Click on Add to set up a dynamic DNS configuration. This screen allows you to add a dynamic DNS address from DynDNS.org or TZO. First select the D-DNS provider—DynDNS.org or TZO—from which you have obtained a dynamic DNS address.
Logout To log out of the router’s user interface at any time during the setup, click on the Logout button. A confirmation screen will appear confirming that you really want to log out.
Advanced Setup This section of the setup is an advanced version of the quick setup. If you want to make specific configurations to your router such as creating a virtual server, DMZ, RIP, Quality of Service (QoS), etc., consider going through this advanced setup for a more comprehensive configuration. ADSL The ADSL settings page contains a modulation and capability section to be specified by your ISP. Consult your ISP to select the correct settings for each.
The test mode can be selected from the DSL Advanced Settings page. Test modes include—normal, reverb, medley, no retrain, and L3. After you make your selections of the test mode, click on Apply to save these settings first before you go to Tone Selection. ADSL Tone Settings The frequency band of ADSL is split up into 256 separate tones, each spaced 4.3125 kHz apart. With each tone carrying separate data, the technique operates as if 256 separate modems were running in parallel.
Virtual Server If you enable NAT (Network Address Translation), you can configure the Virtual Server, Port Triggering, and DMZ Host. NAT—Virtual Servers Setup A virtual server allows you to direct incoming traffic from the WAN side to a specific IP address on the LAN side.The following figure shows the screen that allows you to configure your virtual server(s). Click on the Add button to configure a virtual server.
32
The following screen appears after you save your selection. To add additional virtual servers, click on the Add button. If you need to remove any of the server names, select the check box and click on the Remove button. DMZ You can define the IP address of the DMZ Host on this screen. Enter the IP address and click on Apply.
SNMP SNMP—Configuration SNMP is Simple Network Management Protocol that provides a means to monitor status and performance as well as set configuration parameters. It enables a management station to configure, monitor and receive trap messages from network devices. IP Filter IP filters can be configured to manage your incoming and outgoing traffic. Click on the Inbound and Outbound buttons to advance to the next section for further configuration.
Incoming IP Filtering Setup Incoming IP filter allows specified the WAN traffic to pass through the firewall. Click on the Add button to add incoming filter settings. Enter a filter name, information about the source address (from the WAN side), and information about the destination address (to the LAN side). Select the protocol and WAN interface, then click on Apply to add the setting.
The following screen appears when you apply the IP filter. The screen lists the IP filters that were added from the previous screen. To change your settings, click on the Add or Remove buttons.
Outgoing IP Filtering Setup The outgoing filter will block the LAN traffic from entering the WAN side. Click on the Add button to create filters.
The below screen will appear when you click on Add. Input the filter name, source information (from the LAN side), and destination information (from the WAN side). Then click on Apply to save. The following screen appears when you apply the IP filter. The screen lists the IP filters that were added from the previous screen. To change your settings, click on the Add or Remove buttons.
Bridge Filters MAC Filtering Setup MAC filtering can forward or block traffic by MAC address. You can change the policy or add settings to the MAC filtering table using the MAC Filtering Setup screen.
If you click on Change Policy, a confirmation dialog allows you to verify your change. If you want to add a setting to the MAC filtering table, select protocol type, enter the destination and source MAC address, the necessary frame direction, and WAN interface (bridge mode only). Then click on Apply to save.
After you save the settings, a screen showing the settings will appear. On this screen you will be able to view and delete MAC filtering rules. Parental Control Time of Day Restrictions In a home setting, parents can also restrict the day of the week certain computers can access the router. Click on Add to set up the restrictions. After you click you on Add, you will see the below screen where you will be able to enter the MAC address of the PC that you wish to place on a time of day restriction.
Routing Static route, default gateway, and RIP type routing configurations can be performed here.
Routing--Static Route The Static Route page can be used to add a routing table (a maximum of 32 entries can be configured). To proceed, click on Add.
Enter the route information and then apply your configurations. Routing—Default Gateway The router has the ability to accept the first received default gateway assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC’s. This function is enabled by default as seen below.
If you uncheck the Enable Automatic Assigned Default Gateway option, the below screen will be shown. Enter the default gateway IP address or select the established gateway to be used.
Routing—RIP Configuration If RIP is enabled, the router operation can be configured as active or passive.
Quality of Service You can configure the Quality of Service to apply different priorities to traffic on the router. Click on Add to view the Add Network Traffic Class Rule screen.
This screen allows you to add a network traffic class rule.
Port Mapping Port mapping is a feature that allows you to open ports to allow certain Internet applications on the WAN side to pass through the firewall and enter your LAN. To use this feature, mapping groups should be created. Click on the Add button as displayed below. If you need to remove an entry, then click on the Remove button. After clicking the Add button, the below configuration screen appears, allowing you enter the groups and the interfaces they are associated with.
50
Certificate There are two types of certificates—local & trusted CA. Local A local certificate identifies your router over the network. To apply for a certificate, click on Create Certificate Request and if you have an existing certificate, click on Import Certificate to retrieve it.
If you need to create a certificate request, enter the following information— • • • • • Certificate name Common name Organization name State/province name Country/region name.
If you already have a certificate, then you can simply import the certificate by pasting the certificate content and private key into the space provided. Click Apply to submit the request to import the certificate.
The trusted certificate authority (CA) allows you to verify the certificates of your peers. Note that you can store up to 4 certificates. The below screen also allows you to view the CA’s that you may have already added and can be removed. Click on Import Certificate to continue to the next screen. Paste the content of the certificate that you wish to add and click Apply.
The Wireless section under Advanced contains three sections for further configurations. Sections include— • • • • Advanced Settings MAC Filter Bridge QoS (Quality of Service) Wireless—Advance Setting Advanced features of the wireless LAN interface can be configured in this section.
Settings can be configured for the following— • AP Isolation—if you select enable, then each of your wireless clients will not be able to communicate with each other. • Band—a default setting at 2.4GHz – 802.11g • Channel—802.11b and 802.11g use channels to limit interference from other devices. If you are experiencing interference with another 2.4Ghz device such as a baby monitor, security alarm, or cordless phone, then change the channel on your router.
• Transmit Power— this is the percentage of power that should be transmitted from your wireless router. Select from 20%, 40%, 60%, 80%, and 100%.
Wireless—MAC Filter The MAC Filter feature allows you to disable, allow or deny users access to the wireless router based on their MAC address. To add MAC addresses, click on Add to continue. Click on Remove if you want to take out a MAC address from the MAC filter list. The MAC filter screen allows you to manage MAC address filters. Add the MAC addresses that you want to manage and then select the mode that you want to use to manage them.
Wireless—QoS WMM (Wi-Fi Multimedia) technology is available on the wireless router, allowing you to give multimedia applications a higher quality of service and priority in a wireless network so applications such as videos will be of higher quality. Enabling WMM may delay the network traffic of other lower assigned quality applications. WMM No Acknowledgement can be enabled if you enable WMM which refers to the acknowledgement policy used at the MAC level.
Tools The tools section contains various administrator functions to maintain your router. Sections include the following—Admin, Time, Remote Log, System, Firmware, and Test.
Access Control—Admin Three user names and passwords—admin, support, and user—can be used to control your router. The passwords for these user names can be changed on the following screen. Enter the user name followed by the old password and the new password that you wish to change to.
Access Control—Services Services that can be enabled / disabled on the LAN / WAN are FTP, HTTP, ICMP, SNMP, Telnet, and TFTP. Access Control—IP Address Web access to the router can be limited when Access Control Mode is enabled. The IP addresses of allowed hosts can be added using Access Control→IP Address. Add the IP address to the IP address list by clicking on the Add button, then select “Enabled” to enable Access Control Mode.
To assign the IP address of the management station that is permitted to access the local management services, enter the IP address in the box and click on the Apply button.
Time The Time Settings page allows you to automatically synchronize your time with a time server on the Internet. If you choose to set the router’s time, click on the “automatically synchronize with Internet time servers” checkbox and the below fields appear. Select from the list of NTP (Network Time Protocol) time servers. Then select the time zone that you are in and click on Apply to save.
Remote Log The Log dialog allows you to view and configure the log. To view the log, click on the View System Log button. Below is the System Log screen which shows the date/time of the log, the facility that was logged, the severity level and the log message. Click on Refresh to view any new information that is logged. NOTE: When you click on the View System Log button, the System Log screen that you access will be located under the Status section (see screen on left).
If the log is enabled, the system will log selected events including Emergency, Alert, Critical, Error, Warning, Notice, Informational, and Debugging. All events above or equal to the selected log level will be logged and displayed. If the selected mode is “Remote” or “Both”, events will be sent to the specified IP address and UDP port of a remote system log server. If the selected mode is “Local” or “Both”, events will be recorded in the local memory.
67
System The system section includes several tools on one page, including save and reboot, backup settings, update settings, and restore default settings. Save and Reboot To save all configurations made, click on the Save/Reboot button. This will save all your settings and restart the router for the settings to take effect.
When completed, the below pop-up window will appear confirming that the router has been rebooted. Backup Settings To save your configurations in a file on your computer so that it may be accessed again later if your current settings are changed, click on the Backup Settings button. The below pop-up screen will appear with a prompt to open or save the file to your computer.
Update Settings To load a previously saved configuration file onto your router, click Browse and select the file on your computer and then click on Update Settings. The router will restore settings and reboot to activate the restored settings. Restore Default Settings Restore Default will delete all current settings and restore the router to factory default settings. Click on the Restore Default Settings button to proceed.
When completed, the below pop-up window will appear confirming that the router has been rebooted.
Firmware If your ISP releases new software for this router, follow these steps to perform an upgrade. 1. Obtain an updated software image file from your ISP. 2. Enter the path to the image file location or click on the Browse button to locate the image file. 3. Click the Update Software button once to upload the new image file. The below page will appear when you click on the Update Software button.
When completed, the below pop-up window will appear confirming that the router has been rebooted. Test The diagnostics screen allows you to run diagnostic tests to check your DSL connection.
74
Status The status section allows you to view general and status information for your router’s connection. Device Info It shows details of the router such as the version of the software, bootloader, LAN IP address, etc.
DHCP Clients Access the DHCP Leases screen by clicking “DHCP” under “Statistics”. This shows the computers, identified by the hostname and MAC address that have acquired IP addresses by the DHCP server with the time that the lease for the IP address is up.
WAN Info The WAN Info screen displays WAN connections previously set up in the Home section. The information added in the status section is the extra column for connection status information, displaying either ADSL Link Down or ADSL Link Up. Route Info The Route Info section displays route information showing the IP addresses of the destination, gateway, and subnet mask as well as other route information.
Log This is the same screen as seen in the Remotelog section under tools.
LAN The LAN section shows received and transmitted packet information for the Ethernet interfaces. Click on Reset Statistics to renew the information.
WAN The WAN section shows received and transmitted packet information for the WAN connections that you have set up. Click on Reset Statistics to renew the information. ATM The ATM section displays statistical values for your ATM interface as well as for AAL5 and AAL5 VCC. Click on Reset Statistics to renew the values.
81
ADSL Information contained in the ADSL screen is useful for troubleshooting and diagnostics of connection problems.
ADSL BER Test A Bit Error Rate Test (BER Test) is a test that reflects the ratio of error bits to the total number transmitted. If you click on the ADSL BER Test button at the bottom of the ADSL Statistics page, the following pop-up screen will appear allowing you to set the tested time and to begin the test. When you start the ADSL BER Test, the following progress window will display the connection speed as well as the length of time that the test will run for.
When the test is complete, the following window will display the test results showing the test time, total transferred bits, total error bits and error ratio. Wireless Station Info This page displays the stations (identified by their BSSID) that are associated with your wireless router. Click on Refresh to renew the page for new wireless stations.
