DSL-200 ADSL USB Modem User’s Guide First Edition (Jan.
DSL-200 ADSL USB Modem User’s Guide Wichtige Sicherheitshinweise 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Bitte lesen Sie sich diese Hinweise sorgfä ltig durch. Heben Sie diese Anleitung für den spä tern Gebrauch auf. Vor jedem Reinigen ist das Gerä t vom Stromnetz zu trennen. Vervenden Sie keine Flüssigoder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung.
DSL-200 ADSL USB Modem User’s Guide Limited Warranty Hardware: D-Link warrants its hardware products to be free from defects in workmanship and materials, under normal use and service, for the following periods measured from date of purchase from D-Link or its Authorized Reseller: Product Type Warranty Period Complete products One year Spare parts and spare kits 90 days The one-year period of warranty on complete products applies on condition that the product's Registration Card is filled out and returned
DSL-200 ADSL USB Modem User’s Guide D-Link pursuant to this warranty, but shall not apply to any update or replacement which may be provided for download via the Internet, or to any update which may otherwise be provided free of charge. D-Link's sole obligation under this software warranty shall be to replace any defective software product with product which substantially conforms to D-Link's applicable product documentation.
DSL-200 ADSL USB Modem User’s Guide D-Link Offices for Registration and Warranty Service The product's Registration Card, provided at the back of this manual, must be sent to a D-Link office. To obtain an RMA number for warranty service as to a hardware product, or to obtain warranty service as to a software product, contact the D-Link office nearest you. An addresses/telephone/fax list of D-Link offices is provided in the back of this manual. Trademarks Copyright © 2006 D-Link Corporation.
DSL-200 ADSL USB Modem User’s Guide Table of Contents ABOUT THIS USER’S GUIDE ...................................................................................................................................... 1 BEFORE YOU START .................................................................................................................................................... 2 INTRODUCTION ...................................................................................................................
DSL-200 ADSL USB Modem User’s Guide About This User’s Guide This user’s guide tells you how to install your DSL-200 ADSL USB Modem and use it to connect to the Internet. ADSL services are provided by, and sold by a variety of businesses. Your ADSL service provider may be your telephone company, an Internet service provider (ISP), a business that specializes in providing network services or a combination of any of these.
DSL-200 ADSL USB Modem User’s Guide Before You Start In addition to the Modem hardware and software drivers, you will to gather information before you begin to install the device. Your DSL service provider will give you information required for a successful ADSL connection. You will use this information when you decide which driver to install and when you configure the Modem.
DSL-200 ADSL USB Modem User’s Guide Microfilters Unless you are instructed to use a “line splitter” (see below), it will be necessary to install a microfilter (low pass filter) device for each telephone or telephone device (answering machines, Faxes etc.) that share the line with the ADSL service. Microfilters are easy-to-install, in-line devices, which attach to the telephone cable between the telephone and wall jack. Microfilters that install behind the wall plate are also available.
DSL-200 ADSL USB Modem User’s Guide ADSL Service In order to use the Modem you must first have ADSL service established with a DSL service provider. There are four standards used for ADSL connections known as ANSI T1.413 issue 2, G.Lite, G.dmt and G.hs. The standards differ somewhat as to data transfer speed or bit rate. For user convenience, the Modem supports the G.hs Auto-handshake ADSL standard. This allows the Modem to operate with either type of connection.
DSL-200 ADSL USB Modem User’s Guide Use the tables provided here to record the information you need to install the Modem. SETTINGS TABLE (all users) VPI: VCI: Software Driver: The driver used depends on the connection protocol used for your network services. ¾ Select the WAN driver if your connection is a PPP connection. That is if you are using RFC 2364 PPP over ATM or RFC 2516 PPPoE PPP over Ethernet. ¾ Select the LAN driver if you are using RFC 1483 Ethernet over ATM.
DSL-200 ADSL USB Modem User’s Guide INTRODUCTION ADSL modem technology is a relatively new technology and may be unfamiliar to the reader. In this section, we introduce you to ADSL technology and give a brief description of its key attributes. We also give a general description of the D-Link DSL-200 USB Modem and its main features.
DSL-200 ADSL USB Modem User’s Guide Product Features The D-Link DSL-200 Modem provides the following features: ¾ G.hs compliant (Auto-handshake) ¾ G.dmt full rate compliant ¾ G.lite compliant ¾ RFC 1483 (Bridged Ethernet) compliant ¾ RFC 2364 PPP over ATM compliant ¾ RFC 2516 PPP over Ethernet compliant ¾ Compatible with all T1.413 issue 2 (full rate DMT over analog POTS), and CO DSLAM equipment ¾ Compliant with USB Specification Revision 1.
DSL-200 ADSL USB Modem User’s Guide LED Indicators There are two LED indicators on the Modem: Power - Indicates the Modem is powered on when lit. ADSL Link – Indicates a valid ADSL link has been established when lit.
DSL-200 ADSL USB Modem User’s Guide MODEM INSTALLATION Before you connect the USB cable, you must install the driver. See the next chapter for driver installation instructions. The only cable you should connect initially is the ADSL cable. Place the Modem in a location so that you are able to view the LEDs. It should be placed in an area that is clean, dry and ventilated. Make certain it is not placed near a heat source.
DSL-200 ADSL USB Modem User’s Guide SOFTWARE INSTALLATION The DSL-200 can be used with the following operating systems: Microsoft Windows 98 Second Edition Microsoft Windows 2000 Microsoft Windows Millennium Edition Microsoft Windows XP Microsoft Windows XP x64 The procedures for each system are slightly different so be sure to follow the instructions provided for your PC’s operating system. The Microsoft Plug and Play feature will automatically detect the modem after it has been installed.
DSL-200 ADSL USB Modem User’s Guide Install Modem Drivers Before starting the software setup process, close all windows and quit any application programs you are running. 1.1 Windows 98SE/ME 1) Insert the DSL-200 Installation CD into the CD-ROM drive. The system should detect the installation program and run the program automatically. If installation does not begin automatically after a few seconds, find the autorun.exe icon located on the CD and double-click it.
DSL-200 ADSL USB Modem User’s Guide 2) Choose the appropriate driver from the driver list and click it. A notification message will appear indicating that the setup process has begun. Choose this driver and click it 3) The Welcome window will appear. Make sure you have quit all other programs and click Next. Click Next.
DSL-200 ADSL USB Modem User’s Guide 4) In the Select Service Provider window, select Other Service Provider and click Next. Click Next. 5) In the Select Driver Type window, choose the driver that best suits your ADSL connection, and then click Next. Select WAN Driver Click Next. 6) In the Communication Settings window you must provide the PVC settings, Encapsulation method and Modulation method for configuring the Modem. Type in the VPI and VCI values in their respective fields.
DSL-200 ADSL USB Modem User’s Guide Enter your VPI and VCI. Select your Encapsulation. Select your Modulation. Click Next 9) The Ready to Install window appears. Click Next to copy the needed driver files. Click Next.
DSL-200 ADSL USB Modem User’s Guide 10) After clicking Next, the Installing screen below will appear notifying you that your computer is downloading files and preparing for installation. Wait for installation. 11) After the files are downloaded, another Installing screen will prompt you to plug your modem into your computer. Plug the rectangular end of the USB cable into the USB port of your PC, and then plug the square end of the USB cable into the USB port of the ADSL Modem.
DSL-200 ADSL USB Modem User’s Guide Please insert Win 98 CD-ROM now. 13) The Found New Hardware screen will appear notifying you that your computer has detected the modem and is currently installing it. 14) At the end of this process, the Reboot screen will appear prompting you to restart your computer. Choose Yes, reboot the computer now because it is necessary to reboot your computer to continue the installation, and then click Close. Click Close to reboot the computer.
DSL-200 ADSL USB Modem User’s Guide After reboot, click Finish to complete the installation. Upon restarting your computer, a new icon (two arrows) will appear in the System Tray. If you are using PPP (WAN driver only) the D-Link Dial-up PPP Connection icon after restarting.
DSL-200 ADSL USB Modem User’s Guide 1.2 Windows 2000/XP 1) Insert the DSL-200 Installation CD into the CD-ROM drive. The system should detect the installation program and run the program automatically. If installation does not begin automatically after a few seconds, find the autorun.exe icon located on the CD and double-click it. To view the contents of the CD, open My Computer from the desktop, and right-click on your CD-ROM.
DSL-200 ADSL USB Modem User’s Guide Click Next. 4) In the Select Service Provider window, select Other Service Provider and click Next. Click Next. 5) In the Select Driver Type window, choose the driver that best suits your ADSL connection, and then click Next. Select WAN Driver or LAN Driver. Click Next.
DSL-200 ADSL USB Modem User’s Guide and Modulation method for configuring the Modem. Type in the VPI and VCI values in their respective fields. 7) In the same window, select the appropriate Encapsulation method from the drop-down menu. You will select the encapsulation setting that is appropriate for the driver you are installing. For RFC 2516 PPPoE, select RFC 2516 PPPoE Encapsulation.
DSL-200 ADSL USB Modem User’s Guide 10) After clicking Next, the Installing screen below will appear notifying you that your computer is downloading files and preparing for installation. Wait for installation. 11) After the files are downloaded, another Installing screen will prompt you to plug your modem into your computer. Plug the rectangular end of the USB cable into the USB port of your PC, and then plug the square end of the USB cable into the USB port of the ADSL Modem.
DSL-200 ADSL USB Modem User’s Guide Click Finish to complete the installation. After finishing the installation procedure, a new icon (two arrows) will appear in the System Tray. If you are using PPP (WAN driver only) the D-Link Dial-up PPP Connection icon desktop after installing.
DSL-200 ADSL USB Modem User’s Guide 1.3 Windows XP 64bit 1) Insert the DSL-200 Installation CD into the CD-ROM drive. The system should detect the installation program and run the program automatically. If installation does not begin automatically after a few seconds, find the autorun.exe icon located on the CD and double-click it. To view the contents of the CD, open My Computer from the desktop, and right-click on your CD-ROM.
DSL-200 ADSL USB Modem User’s Guide 3) The Welcome window will appear. Make sure you have quit all other programs and click Next. Click Next. 4) In the Select Service Provider window, select Other Service Provider and click Next. Click Next. 5) In the Select Driver Type window, choose the driver that best suits your ADSL connection, and then click Next. Select ATM, WAN or LAN Driver. Click Next.
DSL-200 ADSL USB Modem User’s Guide 6) In the Communication Settings window you must provide the PVC settings, Encapsulation method and Modulation method for configuring the Modem. Type in the VPI and VCI values in their respective fields. 7) In the same window, select the appropriate Encapsulation method from the drop-down menu. You will select the encapsulation setting that is appropriate for the driver you are installing. For RFC 2516 PPPoE, select RFC 2516 PPPoE Encapsulation.
DSL-200 ADSL USB Modem User’s Guide 9) The Ready To Install window appears. Click Next to copy the needed driver files Click Next 10) After clicking Next, the Installing screen below will appear notifying you that your computer is downloading files and preparing for installation. Wait for installation.
DSL-200 ADSL USB Modem User’s Guide 11) After the files are downloaded, another Installing screen will prompt you to plug your modem into your computer. Plug the rectangular end of the USB cable into the USB port of your PC, and then plug the square end of the USB cable into the USB port of the ADSL Modem. The USB Modem will be detected and messages will be displayed as the modem software is installed. Plug in your Modem now.
DSL-200 ADSL USB Modem User’s Guide Making a Connection Fixed IP Your need to specify the fixed IP address and other required settings in this window to perform your connection. Enter your IP address, Subnet mask and Default gateway. Enter your Preferred and/or Alternate DNS server. Click OK.
DSL-200 ADSL USB Modem User’s Guide Dynamic IP Double click the icon named Connect D-Link Dial-Up PPP Connection on desktop. Enter user name and password provided by the service provider to perform the connection. Enter your User name and Password. Click Dial.
DSL-200 ADSL USB Modem User’s Guide Verify the ADSL Connection Before you continue to the final step, make sure that the ADSL connection has been established. This can be done easily using the Modem’s ADSL connection monitoring feature described below. Desktop Monitoring A new icon will appear in the System Tray of your desktop. These colored arrows will help you monitor the status of your ADSL connection. The table below summarizes how to interpret the icon indicator.
DSL-200 ADSL USB Modem User’s Guide CONNECT TO THE INTERNET Now that the driver has been installed, you are ready to connect to the Internet. You establish an Internet connection indirectly, using DSL link to your network service provider. Follow the instructions for the driver you have installed and the operating system you use on your computer. If you have installed the WAN driver, you are using PPP to connect to your network service provider.
DSL-200 ADSL USB Modem User’s Guide 2. In the Connect To window type in the correct User name and Password given to you by your ADSL or network service provider. Checks the Save password box if do not want to retype the password if you need to reconnect. The Phone number field will display the VPI/VCI values you entered earlier. DO NOT change the numbers in the Phone number field if displayed. Click Dial. It may take a few seconds for the connection to be established. 3.
DSL-200 ADSL USB Modem User’s Guide Windows 98 / Windows Me (LAN Driver) Follow these steps if you are using the RFC 1483 or RFC 1577 protocol on a computer running Windows 98 or Windows Me. 1. From the Start menu, select Settings, Control Panel, and then double-click on the Network icon. 2. The Network window appears. Select the Configuration tab, scroll down the installed network components list and click on TCP/IP D-Link DSL-200 USB ADSL Modem. 3. Click the Properties button. 4.
DSL-200 ADSL USB Modem User’s Guide MONITORING THE MODEM Once you have installed the Modem you can monitor the status of the ADSL connection by clicking on the connection icon in your System Tray or click on the DSL-200 icon in the Control Panel folder. Clicking on either icon will bring up the following window: The bright green light under the screen indicates a valid link. The screen indicates the current state of you modem, the modulation and the Rx and the Tx data rates.
DSL-200 ADSL USB Modem User’s Guide Under the screen to the left are two scroll buttons . Clicking on the right scroll button will bring up the screen pictured above, showing the Current Package, Driver, Control Panel and Firmware versions. Clicking on the left scroll button will return you to the initial screen.
DSL-200 ADSL USB Modem User’s Guide CHANGING MODEM CONFIGURATION Once the Modem and software have been installed the communication settings may be easily updated by performing the following steps: 1. From your PC desktop click Start – ALL Programs – -Link DSL-200 ADSL Modem – Configure. A notification message will appear indicating that the setup process has begun.
DSL-200 ADSL USB Modem User’s Guide 2. The “Communication Settings” window will be displayed. Make the necessary changes to the VPI, VCI, Encapsulation type and/or Modulation type and click Next. 3. The new settings will be applied after restarting the computer. If you want to restart now click Close. If you do not want to restart now select the “No, I will restart my computer later.” option and then click Close.
DSL-200 ADSL USB Modem User’s Guide Configuring the Idle time You can configure the idle time to automatically disconnect the connection after there is no package passing through the connection for the specified period of time by performing the following steps: 1. From the Windows desktop double-click on the D-Link Dial-Up PPP Connection icon while you are not using this connection to bring up the properties window. Double Click 2. In the D-Link Dial-Up PPP Connection window, choose Options tab.
DSL-200 ADSL USB Modem User’s Guide UNINSTALLING THE MODEM If you need to uninstall the Modem, use the Uninstall program available in the DSL-200 Modem folder. Failure to use the Uninstall program can leave files in the system that can cause problems with future installations, including problems with reinstallation of the Modem. IMPORTANT: Do not remove the Modem using the device manager. You must use the Uninstall Program to remove the device.
DSL-200 ADSL USB Modem User’s Guide 2. You are asked to confirm your intention to remove the device (software). Click Yes to uninstall the Modem. 3. A new window appears and asks that you not unplug the USB cable until after the device driver has been completely removed. Click OK to proceed. 4. A new window appears asking that you unplug the USB cable. Please unplug your modem from the computer and click OK to proceed. 5.
DSL-200 ADSL USB Modem User’s Guide TECHNICAL SPECIFICATIONS General Standards: Protocol: Data Transfer Rate: Software Drivers: Media Interface Exchange: ANSI T1.413 issue 2 ITU G.992.1 (G.dmt) ITU G.992.2 (G.lite) ITU G.994.1 (G.hs) USB 1.1 specifications RFC 2364 PPP over ATM Adaptation Layer 5 RFC 2516 PPP over Ethernet RFC 1483 Multi-protocol Encapsulation over ATM Adaptation Layer 5 G.dmt full rate downstream: up to 8Mbps G.dmt full rate upstream: up to 640Kbps G.lite ADSL downstream: up to 1.
International Offices U.S.A 17595 Mt. Herrmann Street Fountain Valley, CA 92708 TEL: 1-800-326-1688 URL: www.dlink.com Canada 2180 Winston Park Drive Oakville, Ontario, L6H 5W1 Canada TEL: 1-905-8295033 FAX: 1-905-8295223 URL: www.dlink.ca Europe (U. K.) 4th Floor, Merit House Edgware Road, Colindale London NW9 5AB U.K. TEL: 44-20-8731-5555 FAX: 44-20-8731-5511 URL: www.dlink.co.uk Germany Schwalbacher Strasse 74 D-65760 Eschborn Germany TEL: 49-6196-77990 FAX: 49-6196-7799300 URL: www.dlink.de France No.
Registration Card Print, type or use block letters. Your name: Mr./Ms________________________________________________________________________________ Organization: ___________________________________________ Dept.
