Safety Notices Please read the following safety notices before installing or using this phone. They are crucial for the safe and reliable operation of the device. Please use the external power supply that is included in the package. Other power supplies may cause damage to the phone, affect the behavior or induce noise. Before using the external power supply in the package, please check with home power voltage. Inaccurate power voltage may cause fire and damage. Please do not damage the power cord.
Table of Content 1 2 INTRODUCING VOIP PHONE.................................................................................................6 1.1 SIMPLE INTRODUCTION...........................................................................................................6 1.2 DELIVERY CONTENT...............................................................................................................6 1.3 KEYPAD .......................................................................................
5 6 7 8 OTHER FUNCTIONS...............................................................................................................22 5.1 AUTO HANDDOWN ...............................................................................................................22 5.2 BAN ANONYMOUS CALL .......................................................................................................22 5.3 DIAL PLAN ...........................................................................................
8.3.2.6 8.3.3 VOIP ............................................................................................................................... 44 8.3.3.1 SIP....................................................................................................................................... 44 8.3.3.2 STUN................................................................................................................................... 52 8.3.3.3 DIAL PEER .......................................
1 Introducing VoIP Phone 1.1 Simple Introduction Thank you for your purchasing DPH-400S/DPH-400SE.DPH-400S/ DPH-400SE is a full-feature telephone that provides voice communication over the same data network that your computer uses. This phone functions not only much like a traditional phone, allowing to place and receive calls, and enjoy other features that traditional phone has, but also it owns many data services features which you could not expect from a traditional telephone.
1.3 Keypad Key Key name Function Description Navigation keys assist users for operating. In idle state they have special function. Navigation You can configure through the web page according to your patterns of use. Access to phone book, check the record list and add new records and revise the record. When check Phonebook the phone book record, press this key again will return to idle mode. Press this key in calling mode, you can hear the Mute other side, and the other side cannot hear you.
Turn down or turn up the volume by pressing these Volume -/+ two keys. Redial Hands-free Indicator light Soft key 1/2/3/4 Call logs 1. In the hook off /hands-free mode, use the key to dial the last call number. 2. In stand-by mode, it has a function to check the Outgoing Call. Make the phone into hands-free mode. If power on, the indicator is light. Keys combination, include functions such as History/PBook /DND /Menu /Del /Redial /Send / Quit/Answer/Divert/Reject/Hold/Transfer/Conf/Cl ose and so on.
LAN 10/100M Connect it to PC. Headset Port type: RJ-9 connector. Handset Port type: RJ-9 connector. External console Port type: RJ-11 direct connector. interface 1.5 Icon introduction Icon Description Call out. Call in. Call hold. Auto answer. Call mute. Contact. DND(Do not Disturb). In hand free mode. In handset mode. In headset mode. SMS. Missed call. Call forward.
1.6 LED introduction Table 1 Programmable key LEDs for BLF LED Status Description Steady green The object is in idle status. Slow blinking red The object is ringing. Steady red The object is active. Fast blinking red The object is failed. Off No subscribe. Table 2 Programmable key LEDs for Presence LED Status Description Steady green The object is online. Slow blinking red The object is ringing. Steady red The object is active. Fast blinking red The object is failed. Off No subscribe.
Shared network connection—Use this method if you have a single Ethernet port in your workspace with your desktop computer already connected to it. First, disconnect the Ethernet cable from the computer and attach it to the WAN port on the back of your phone. Next, use the Ethernet cable in the package to connect LAN port on the back of your phone to your desktop computer. Your IP Phone now shares a network connection with your computer. The following figure is for your reference.
finishing startup, phone will show greeting, current date and time and so forth. 4. If phone has registered to the server, you can place or answer calls. 2.2 Basic Initialization DPH-400S/DPH-400SE is provided with a plenty of functions and parameters for configuration. User needs some network and VoIP knowledge so that user could understand the meanings of parameters.
5. Press Quit six times to return to the idle screen. 6. Check the status, the screen shows “Static” .the screen shows the IP address and gateway which were set just now, if the phone could display the right time, it shows that Static IP mode takes effect. Setting DHCP mode 1. Press Menu->Settings->Advanced Setting, then enter passwords, and choose network ->WAN->Net Mode, enter and choose DHCP through navigation keys and press the Save key. 2. Press Quit six times to return to the idle screen. 3.
3.2 Answering a call Answering an incoming call 1. If you are not on another phone, lift the handset using, or press the Speaker button/ Answer softkey to answer using the speakerphone, or press the headset button to answer the headset. 2. If you are on another call, press the answer softkey. During the conversation, you can alternate between Headset, Handset and Speaker phone by pressing the corresponding buttons or picking up the handset. 3.3 DND Press DND softkey to active DND Mode.
3.6 Call Waiting 1. Press Menu ->Features->Enter->Call Waiting->Enter. 2. Use the navigation keys to active or inactive call waiting. 3. Then press the Save to save the changes. 3.7 Mute Press Mute button during the conversation, icon will be showed in the LCD. Then the called will not hear you, but you can hear the called. Press it again to get the phone to normal conversation. 3.8 Call transfer 1.
3. When the call is answered, press Conf and add the first call to the conference. 4. If you want to release the conference, press Split key. 3.10 Multiple-way call If user has 4 line calls and wants to invite the five party during the call, they can press Conf or Transf “New Call”, press OK, enter the number ,then press Send and wait for the other party to answer. When the multiple-way calls, you can press the arrow keys to select a call.
4 Advanced function 4.1 Call pickup Call pickup is implemented by simulating pickup function of PBX. it’s that, when A calls B, B rings but no answer, at this moment, C can hook off and input an appointed prefix plus B’s number, pick up A’s call and talk with A. The following chart shows how to configure an appointed prefix in dial peer to have call pick up function. *1* means appointed prefix code. After making the above configuration, C can dial *1* plus B’s phone number to pick up A’s call.
*3* is appointed prefix code. After making the above configuration, A can dial *3* plus B’s phone number to make the redial function. *4* is appointed prefix code. After configuration, A can dial *4* to cancel redial function. User can set prefix in random, in the case of no affecting current dialing rules. 4.
4) If you want to write a message, you can press New and enter message. Use the 123 softkey to change the Input Method. When you input the message you want to send, press OK, then use the navigation keys to select the line from which you want to send, then Send. 5) If you want to delete the message, after view the message, press Del, then you have three options to choose: Yes, All, No. 4.8.2 Memo You can add some memos to record some important things to remind you.
environment as a quick access to connect to the operator or the secretary. BLF BLF is also called “Busy lamp field”, and it is used to prompt the user to pay attention to the state of the object than has been subscribed, and used to cooperate with the server to pick up the phone call. You can configure the key for Busy Lamp Field (BLF) which allows you to monitor the status (idle, ringing, or busy) of other SIP account. User can dial out on a BLF configured key.
Prefix SMS Call Back Hot Desking: Pressing the key, you can clear all sip information and register yourself sip information 4. Set the type as Dtmf You can configure the key as Dtmf. This key function allows you to easily dial or edit dial number. 5. Set the type as Remote You need to match a XML Phonebook address, pressing the button you can directly access the corresponding remote phonebook. 6. Set the type as BLF List Key It needs the cooperation with the Broadsoft server.
5 Other functions 5.1 Auto Handdown 1. Press Menu ->Features-> Enter->Auto Handdown-> Enter. 2. Set the Mode Enable through the navigation key, then set Time, unit is minute, then press Save. 3. When the call ends, after the time that you have set, the phone will back to the idle interface. 5.2 Ban Anonymous Call 1. Press Menu ->Features-> Enter->Ban Anonymous Call-> Enter. 2. Choose which sip you want to enable Ban Anonymous Call, and then press Enter, choose Enabled or Disabled through navigation key.
3. After enable auto redial, calling out someone, if he is in busy, it will pop up a prompt box whether to auto redial, press OK, the phone will call out him according the Interval and Times that you set. 5.6 Call completion 1. Press Menu ->Features-> Enter->Call Completion-> Enter. 2. Enable the function through the navigation key, and then Save . 3.
6 Basic setting 6.1 Keyboad 1. Press Menu ->Settings-> Enter->Basic Setting-> Enter->Keyboard->Enter. 2. There are four items: DSS Keys, Multiplex, Long Click, SoftKey, You can set up respectively on them. Press the key Enter to the interface, then use the navigation keys to choose the function for the key according to you want. 3. Press the key OK to save. 6.2 Screen Set 1. Press Menu ->Settings-> Enter->Basic Setting-> Enter->Screen Set->Enter. 2.
6.6 Greeting Word 1. Press Menu ->Settings-> Enter->Basic Setting-> Enter->Greeting Word->Enter. 2. You can enter the message and press Save, it will display in the phone screen when the phone start up. 6.7 Language Setting 1. Press Menu ->Settings-> Enter->Basic Setting-> Enter->Language->Enter. 2. DPH-400S/DPH-400SE support three languages, you can use the navigation keys to choose. The default two languages are English and Chinese.
7 Advanced settings 7.1 Account Press Menu->Enter->Advanced settings, and then input the password to enter the interface, the default password is 123. You can set it through the web page. Then choose Account then press Enter, you can do some SIP settings. 7.2 Network Press Menu->Enter->Advanced settings, and then input the password to enter the interface. Then choose Network and press Enter, you can do network settings, you can refer to 2.2.1 Network settings. 7.
8 Web configuration 8.1 Introduction of configuration 8.1.1 Ways to configure DPH-400S/DPH-400SE has three different ways to different users. Use phone keypad. Use web browser (recommendatory way). Use telnet with CLI command. 8.1.2 Password Configuration There are two levels to access to phone: root level and general level.
8.3 Configuration via WEB 8.3.1 BASIC 8.3.1.
WAN/LAN Accounts 8.3.1.2 (Static, DHCP, PPPoE), MAC address, the IP address of WAN port and LAN port, ON or OFF of DHCP mode of LAN port and bridge mode. Shows the phone numbers provided by the SIP LINE 1~5 servers. The last line shows the version number. Wizard Wizard Please select the proper network mode according to the network condition.
IP Address Subnet Mask IP Gateway DNS Domain Primary DNS Secondary DNS Input the IP address distributed to you. Input the Netmask distributed to you. Input the Gateway address distributed to you. Set DNS domain postfix. When the domain which you input cannot be parsed, phone will automatically add this domain to the end of the domain which you input before and parse it again. Input your primary DNS server address. Input your secondary DNS server address.
Password SIP User Enable Registration Input the phone number assigned by your VOIP service provider. Start to register or not by selecting it or not. Display detailed information that you manual configure. Choose DHCP MODE，click【NEXT】can configure SIP(default SIP1)simply, also can browse too. Click【BACK】can return to the last page. Like Static IP MODE. Choose PPPoE MODE，click【NEXT】can configure the PPPoE account/password and SIP(default SIP1)simply, also can browse too.
Password Input your ADSL password. Notice: Click【Finish】button after finished your setting, IP Phone will save the setting automatically and reboot, After reboot, you can dial by the SIP account. 8.3.1.3 Call Log You can query all the dialed calls through this page. Call Log Field name Start Time Duration Dialed Calls 8.3.1.4 explanation Display the start time of the dialed calls. Display the conversation time of the dialed calls. Display the account /line of the dialed calls.
Language Set the language of phone, English is default. The greeting message will display on LCD when Greeting Words phone is idle. It can support 12 chars. the default chars are VOIP PHONE. Notice: the maximal length of the greeting message is twelve English characters and five Chinese characters. 8.3.2 Network 8.3.2.1 WAN WAN Status Active IP Address The current IP address of the phone.
Current Subnet Mask MAC Address Current IP Gateway The current Netmask address. The current MAC address of the phone. The current Gateway IP address. Please select the proper network mode according to the network condition. DPH-400S/DPH-400SE provide three different network settings: Static: If your ISP server provides you the static IP address, please select this mode, and then finish Static Mode setting. If you don’t know about parameters of Static Mode setting, please ask your ISP for them.
User Input your ADSL account. Password Input your ADSL password. Notice: 1) Click “Apply” button after finished your setting, IP Phone will save the setting automatically and new setting will take effect. 2) If you modify the IP address, the web will not response by the old IP address. Your need input new IP address in the address column to logon in the phone.
NAT Port Mirror Enable Bridge Mode DHCP server setting will take effect. Select NAT or not. Select Port Mirror or not, it only works in bridge mode, the function of the port mirror is that copy the data stream from the WAN port to the LAN port of the phone. Select Bridge Mode or not: If you select Bridge Mode, the phone will no longer set IP address for LAN physical port，LAN and WAN will join in the same network. Click “Apply”, the phone will reboot.
In chart 1, there is a layer 2 that switches without setting VLAN. Any broadcast frame will be transmitted to the other ports except the send port. For example, a broadcast information is sent out from port 1 then transmitted to port 2,3and 4. In chart 2, red and blue indicate two different VLANs in the switch, and port 1 and port 2 belong to red VLAN, port 3 and port 4 belong to blue VLAN.
QoS &VLAN LLDP Settings Enable LLDP Enable Learning Function Package Interval QoS Setting Enable DSCP SIP DSCP Audio RTP DSCP WAN Port VLAN Setting Enable WAN Port VLAN WAN Port VLAN ID SIP 8021.p Priority Enable LLDP by selecting it. After enabling LLDP Learn, telephone can automatically learn the data of DSCP, 802.1p, VLAN ID from the switch. If the data is different from the data of the LLDP server, telephone will change its own value as the value of the switch (Synchronous with VLAN in switch).
Audio 802.1p Priority LAN Port VLAN Setting LAN Port VLAN Mode LAN Port VLAN ID 8.3.2.4 range of the value is 0-7. Specify the value of the voice 802.1p priority, the range of the value is 0-7. Follow WAN: Follow the WAN ID. Disable: Disable Port VALN. Enable: Enable Port VLAN and specify the Port VLAN ID different from WAN ID. Specify the value of the Port VLAN ID different from WAN ID, the range of the value is 0-4095. Service Port You can set the port of telnet/HTTP/RTP by this page.
HTTPS Port value is 8090, the accessing address is http://192.168.1.70:8090. Before using the https, you must download https authentication certification into the phone, then set web browser port, the default is 443 port，if you want to enhance system safety，you'd better change it Telnet Port RTP Port Range Start RTP Port Number into non-443 standard port. You can access to the web in https after rebooting the phone. Set Telnet Port, the default is 23. You can change the value into others.
8.3.2.5 DHCP SEVICE DHCP SERVICE Field name DHCP Lease Table explanation IP-MAC mapping table. If the LAN port of the phone connects to a device, this table will show the IP and MAC address of this device. Shows the DHCP Lease Table， the unit of Lease time is Minute. Leased Table Name Start IP Address End IP Address Subnet Mask IP Gateway Specify the name of the lease table. Set the start IP address of the lease table.
Leased Time DNS Server Address Set the Lease Time of the lease table. Set the default DNS server IP of the lease table; Click the Add button to submit and add this lease table. Select name of lease table, click the Delete button will delete the selected lease table from DHCP lease table. DNS Relay Select DNS Relay, the default is enabled. Click the Apply button to become effective. Notice: 1) The size of lease table cannot be larger than the quantity of C network IP address.
TIME&DATE Field name explanation Simple Network Time Protocol (SNTP) Settings Enable SNTP Enable SNTP by selecting it. Enable DHCP Time Enable DHCP Time by selecting it, then the phone will automatically synchronize the standard time. Primary Server Set SNTP Primary Server IP address. Secondary Server Set SNTP Secondary Server IP address. Time Zone Select the Time zone according to your location. Resync Period Set the time out, the default is 60 seconds.
Default is 24 hours mode. Specify the date display format. Date format Daylight Saving Time Settings Enable Enable daylight saving time. Offset(minutes) Setup the variety length. Month Setup start and end month. Week Setup start and end week. Day Setup start and end day. Hour Setup start and end hours. Minute Setup start and end minutes. Manual Time Settings Notice: You need specify the above all items. Notice: You need specify the above all items. 8.3.3 VOIP 8.3.3.
SIP Config Field name explanation SIP Line Choose line to set info about SIP, there are 4 lines to choose. You can switch by【Load】button.
Basic Settings Status Server Address Server Port Authentication User Authentication Password SIP User Display Name Proxy Server Address Proxy Server Port Proxy User Proxy Password Domain Realm Backup Server Address Backup Server Port Enable Registration Codecs Settings Disable Codecs/Enable Codecs Advanced SIP Setting Shows if the phone has been registered the SIP server or not; or so, show Unapplied. Input your SIP server address. Set your SIP server port. Input your SIP register account name.
will be forwarded to the appointed phone after a specific. Always：Incoming calls will be forwarded to the Forward Number No Answer Forward Wait Time Transfer Timeout Enable Hot Line Hot Line Number Warm Line Wait Time SIP Encryption SIP Encryption Key RTP Encryption RTP Encryption Key Enable Auto Answer Auto Answer Timeout Enable Session Timer Session Timeout Subscribe for MWI MWI Number Subscribe Period(s) Conference Type Conference Number appoint phone immediately.
conference number. Registration Expire(s) Set expire time of SIP server register, default is 60 seconds. If the register time of the server requested is longer or shorter than the expired time set, the phone will change automatically the time into the time recommended by the server, and register again.
No Answer CFwd On Code Set the No Answer CFwd On Code, when you choose to enable the on answer forward function on your phone, it will send message to the server, and the server will turn on the function immediately. When there are calls to the extension, the server will forward it to the set number automatically based the forward type. And the IP phone will not show the record in the call history anymore.
Enable Long Contact Convert URI Dial Without Registered Ban Anonymous Call Enable DNS SRV Server Type RFC Protocol Edition Transport Protocol RFC Protocol Edition Keep Authentication Answer With A Single Codec Auto TCP Enable Strict Proxy the default config. Set more parameters in contact field. Convert # to %23 when send the URI. Set call out by proxy without registration. Set to ban Anonymous incoming Call. Support DNS looking up with _sip.udp mode.
Enable BLF List BLF List Number SIP Global Settings Strict Branch Enable Group Registration Failure Retry Time 8.3.3.2 Enable BLF List by selecting it, BLF list is a function which can monitor the group status, it is not one to one monitoring, but the information feedback from the sever to decide which BLF list will monitor. Specify the BLF List Number.
STUN Field name Simple Traversal of UDP through NATs (STUN) Settings STUN NAT Traversal Server Address Server Port Blinding Period SIP Waiting Time explanation Shows STUN NAT Transverse estimation, true means STUN can penetrate NAT, while False means not. Set your SIP STUN Server IP address. Set your SIP STUN Server Port. Set STUN blinding period(s).
Use STUN Enable/Disable SIP STUN. Notice: SIP STUN is used to realize SIP penetration to NAT. If your phone configures STUN Server IP and Port (default is 3478), and enable SIP Stun, you can use the ordinary SIP Server to realize penetration to NAT. 8.3.3.3 DIAL PEER This functionality offers you more flexible dial rule, you can refer to the following content to know how to use this dial rule.
DIAL PEER Field name explanation There are two types of matching conditions: one is full matching, the other is prefix matching. In the Full matching, you need input your desired phone number Phone number in this blank, and then you need dial the phone number to realize calling to what the phone number is mapped. In the prefix matching, you need input your desired prefix number and T; then dial the prefix and a phone number to realize calling to what your prefix number is mapped.
2) All: xxx, it means that xxx will replace some phone number. 3) Del: It means that phone will delete the number with length appointed. 4) Rep: It means that phone will replace the number with length and number appointed. You can refer to the following examples of different alias application to know more how to use different aliases and this dial rule. Call Mode Select different signal protocol, SIP Suffix Set suffix, this is optional config item. It will show no suffix if you don’t set it.
The phone will automatically send out alias number adding your dialed number, if your dialed number starts with your set phone number. When you dial “8309“, the SIP1 server will receive “07558309” You need set Phone Number, Alias and Delete Length. Phone number is XXXT and Alias is rep: xxx If your dialed phone number starts with your set phone number, the first digits same as your set phone number will be replaced by the alias number specified and New phone number will be send out.
DSP Configuration Field name First Codec Second Codec Third Codec Fourth Codec Fifth Codec Sixth codec Handset Input Volume G.729AB Payload Length Onhook Time Default Ring Type Handset Output Volume Speakerphone volume Ring Volume G.722 Timestamps explanation The first preferential DSP codec: G.711A/u, G.722, G.723, G.729, G.726 The second preferential DSP codec: G.711A/u, G.722, G.723, G.729, G.726 The third preferential DSP codec: G.711A/u, G.722, G.723, G.729, G.726 The forth preferential DSP codec: G.
G.723.1 Bit Rate Default Ring Type Tone Standard EnableVAD DTMF Payload Type 8.3.4.2 5.3kb/s or 6.3kb/s is available. Set up the ring by default. Select Tone Standard. Select it or not to enable or disable VAD. If enable VAD, G.729 Payload length could not be set over 20ms. Set DTMF Payload Type. FEATURE In this web page, you can configure Call Transfer, Call Waiting, 3 Ways Call, Black List, white list Limit List and so on.
FEATURE Field name Do Not Disturb Ban Outgoing Enable Call Transfer Semi-Attend ed Transfer explanation Select DND, the phone will reject any incoming call, the callers will be reminded by busy, but any outgoing call from the phone will work well. If you select Ban Outgoing to enable it, and you cannot dial out any number. Enable Call Transfer by selecting it. Enable Semi-Attended Transfer by selecting it.
Enable Auto Redial Auto Redial interval Auto Redial Times Enable Call Completion Enable Call Waiting Enable 3-way Conference Accept Any Call Enable Auto Hand down Auto Hand down Time Ring From Headset Enable Intercom Enable Intercom Mute Enable Intercom Tone Enable Intercom Barge Enable Silent Mode Turn Off Power Light Emergency Call Number Enable Auto Redial by selecting it, then the phone reminds whether redial, when the callee is busy or rejects. Specify the Auto Redial interval.
Enable Password Dial Password Dial Prefix Password Length DND Return Code Busy Return Code Reject Return Code Hide DTMF Push XML Server Enable Password Dial by selecting it, When number entered is beginning with the password prefix, the following N numbers after the password prefix will be hidden as *, N stand for the value which you enter in the Password Length field.
X and are wildcard x means matching any single digit. For example, 4xxx expresses any number with prefix 4 which length is 4 will be forbidden to dialed out means matching any arbitrary number digit. For example, 6 expresses any number with prefix 6 will be forbidden to dialed out. Notice: Block out List support 100 records. 8.3.4.3 DIAL PLAN This system supports 4 dial modes: 1) End with “#”: dial your desired number, and then press #.
DIAL PLAN Configuration Field name Basic Setting Press "#" to Send Dial Fixed Length explanation Set Enable/Disable the phone ended with “#” dial. Specify the Fixed Length of phone ending with. Set the timeout of the last dial digit. The call will be Send after （3-30） sent after timeout.
separated by commas, or a list of digits. x Match any single digit that is dialed. . Match any arbitrary number of digits including none. Tn Indicates an additional time out period before digits are sent of n seconds in length. n is mandatory and can have a value of 0 to 9 seconds. Tn must be the last 2 characters of a dial plan. If Tn is not specified it is assumed to be T0 by default on all dial plans. Cause extensions 1000-8999 to be dialed immediately.
CONTACT Field name Phonebook Table Name Number Ring Type Group explanation Shows the name corresponding to the phone number. Shows the phone number. Shows the ring type of the incoming call. Shows the group of the contact.
Notice: the maximum capability of the phonebook is 500 items, you can select many or a contact to add to group and add to blacklist, and delete many or a contact, and delete all contacts. Add Contact List Name Specify the name corresponding to the phone number. Office Number Specify the office number. Mobile Number Specify the mobile number. Other Number Specify the other number. Ring Type Specify the ring type for the phone number. Line Specify the sip line for the each number.
the Black List, and these calls will be rejected. x and are wildcard x means matching any single digit. for example, 4xxx expresses any number with prefix 4 which length is 4 will be forbidden to be responded. DOT (.) means matching any arbitrary number digit. for example, 6. expresses any number with prefix 6 will be forbidden to be responded. If user wants to allow a number or a series of number incoming, he may add the number(s) to the list as the white list rule.
8.3.4.6 WEB DIAL You can make a call through the WEB DIAL, enter the Dial Num then press Dial, if you want to finish the talk, press Hang-up.
8.3.5 Function Key Function Key Field name Contrast Enable Backlight Function Key Settings key Type explanation Set contrast of screen. Set enable/disable backlight. Show the function key's serial number. Memory Key: settings can be stored in key storage for each number, the standby or off-hook, select the function keys on the keyboard can call this number.
SIP4, SIP5).Key Key Event functions, monitor state. DTMF：In the call, send DTMF. Value Line Subtype URL: You can input remote book url . Set the type parameter values. Choose which lines to use this feature. Select the function parameters Key Event and Memory Event. NOTICE： memory keys can be configured through the following: Speed Dial function, through the configuration of the key corresponding to the number of ways as shown below. User can press the F1 key to allocate this number by line1 line.
EXT KEY EXT KEY has the same usage with the Function key. “In” port connects the phone, “Out” port connects the next one, if there is only, you don’t need for power supply; if there are more than one, you need supply 5V power for the first one, and use RJ-11 direct connector to the others EXT.
SOFTKEY You can configure different functions in different screens for every softkey. 8.3.6 Maintenance 8.3.6.
DPH-400S/DPH-400SE supports DHCP, PnP, TR069 and Phone Flash to obtain the parameters. The PnP and DHCP and Phone Flash are all deployed, endpoint will go by the following process to try to obtain the server address and other parameters, when it boots up: DHCP option PnP server Phone Flash Auto Provision Field name Auto Update Setting Current Config Version Common Config Version explanation Show the current config file’s version.
configurations are the same, the auto provision would stop here. If the endpoints confirm the configuration by Digest method, the endpoints wouldn’t upgrade configuration unless the configuration in the server is different with the running configuration. CPE Serial Number Show CPE Serial Number. User Specify FTP/HTTP/HTTPS server Username. System will use anonymous if username keep blank. Password Specify FTP/HTTP/HTTPS server Password.
name keep blank. For example, 000102030405. Protocol Type Update Interval Update Mode TR069 Settings Enable TR069 ACS Server Type ACS Server URL ACS User ACS Password TR069 Auto Login "Inform" Sending Period 8.3.6.2 Specify the Protocol type FTP、TFTP or HTTP. Specify update interval time, unit is hour. Different update modes: 1. Disable: means no update. 2. Update after reboot: means update after reboot. 3. Update at time interval: means periodic update. Enable TR069 by selecting it.
Syslog Configuration Field name Syslog Setting Server Address Server Port MGR Log Level SIP Log Level Enable Syslog Web Capture Start Stop explanation Set Syslog server IP address. Set Syslog server port. Set the level of MGR log. Set the level of SIP log. Select it or not to enable or disable syslog. Click the start button when you need capture the WAN packet stream of the phone, then open or save the file as the interface. Click the end button to stop capturing the packet stream.
8.3.6.3 Config Config Setting Field name explanation You can save all changes of configurations. Click the Save Configuration Save button, all changes of configuration will be saved, and be effective immediately. Backup Right clicks on “Right click here…” and select “Save Configuration Target As config File(.txt)” then you will save the config file in .txt format, or select “Save Target As config File(.xml)” then you will save the config file in .xml format.
Update Field name Web Update Web Update FTP Update Server Address explanation Click the browse button, find out the config file saved before or provided by manufacturer, download it to the phone directly, press “Update” to save. You can also update downloaded update file, logo picture, ring, mmiset file by web. Set the FTP/TFTP server address for download/upload. The address can be IP address or Domain name with subdirectory. User Set the FTP server Username for download/upload.
Action type that system want to execute： Type Protocol Update Logo File Select File Delete Logo File Select File Logo File Logo File 8.3.6.5 1. Application update: download system update file 2. Config file export: Upload the config file to FTP/TFTP server, name and save it. 3. Config fie import: Download the config file to phone from FTP/TFTP server. The configuration will be effective after the phone is reset. 4. Phone book export (.vcf, .csv, .
Access Configuration Field name explanation Keyboard Password Set the password for entering the setting menu of the phone by the phone‘s key board. The password is digit. This table shows the current user existed. User Set account user name. User Level Set user level, Root user has the right to modify configuration, General can only read. Password Set the password. Confirm Confirm the password.
8.4 Reboot If you modified some configurations which need the phone’s reboot to be effective, you need click the Reboot, then the phone will reboot immediately. Notice: Before reboot, you need confirm that you have saved all configurations. 8.4.1 Security 8.4.1.1 Web Filter WEB Filter User could make some device own IP, which is pre-specified, access to the MMI of the phone to configure and manage the phone.
column, and click Add to add this IP segment. You can also click Delete to delete the selected IP segment. Web Filter setting Select it or not to enable or disable Web Filter. Click Apply to make it effective. Notice: Do not set your visiting IP outside the Web filter range, otherwise, you cannot logon through the web. 8.4.1.
We will give you an instance for your reference. Field name explanation Enable Input Rules Select it to Enable Input Rules. Enable Output Select it to Enable Output Rules. Rules Input / Output Specify current adding rule by selecting input rule or output rule. Deny/Permit Specify current adding rule by selecting Deny rule or Permit rule. Protocol Filter protocol type. You can select TCP, UDP, ICMP, or IP. Port Range Set the filter Port range. Src Address Set source address.
port of private network to public, also is the IP address mapping which we usually say. DMZ config： In order to make some intranet equipments support better service for extranet, and make internal network security more effectively, these equipments open to extranet need be separated from the other equipments not open to extranet by the corresponding isolation method according to different demands.
NAT Configuration Field name IPSec ALG explanation It is an encryption technology. Select it to enable IPSec ALG, the default is enable. FTP is a service of connection layer which can FTP ALG transform intranet IP into extranet IP when intranet IP is sending out packet. Select it to enable FTP ALG, the default is enable. PPTP ALG Select it enable PPTP ALG, the default is enable. Shows the NAT TCP mapping table.
Shows the NAT UDP mapping table. Transfer Type Select the NAT mapping protocol style, TCP or UDP. Inside IP Set the IP address of device which is connected to LAN interface to do NAT mapping. Inside Port Set the LAN port of the NAT mapping. Outside Port Set the WAN port of the NAT mapping. Notice: After finish setting, click the Add button to add new mapping table; click the Delete button to delete the selected mapping table. Shows the outside WAN port IP address and the inside LAN port IP address.
VPN Configuration Field name explanation VPN IP Shows the current VPN IP address. Select L2TP. You can choose only one for current state. After you select it, you’d better save configuration and reboot your phone. Enable VPN Select it or not to enable or disable VPN. VPN Server Addr Set VPN L2TP Server IP address. VPN User Name Set User Name access to VPN L2TP Server. VPN Password Set Password access to VPN L2TP Server.
8.4.1.5 Security Security Field name Update Security File Select Security File explanation Select the security file you want to update, then click Update button to update. Delete Security File Select Security File Select the security file you want to delete, then click Delete button to update. SIP TLS File Show SIP TLS authentication certification file. HTTPS File Show HTTPS authentication certification file. Open VPN Files Show Open VPN File authentication certification file.
8.4.2 Logout Click Logout，and you will exit web page. If you want to enter it next time, you need input user name and password again.
9 Appendix 9.1 Specification 9.1.1 Hardware Item Adapter (Input / Output) port WAN LAN EXT Power Consumption LCD Size Operation Temperature Relative Humidity CPU SDRAM Flash Dimension(L x W x H) Weight DPH-400S/DPH-400SE Input: 100-240V Output: 5V 1A 10/100Base- T RJ-45 1 PORT 10/100Base- T RJ-45 1 PORT RJ11 1 PORT Idle: 2.5W/Active: 2.8W 128x64 53.5 x 70mm 0～40℃ 10～65% Broadcom 16MB 4MB 295×295×175mm 1.5kg 9.1.2 Voice features SIP supports 5 SIP servers Support SIP 2.
Automatically select calling line, if one line can’t be connected, the phone can automatically switch to other line to call.
Support VPN (L2TP) function Wan Port supports main DNS and secondary DNS server, can select dynamically to get DNS in DHCP mode or statically set DNS address. Support DHCP client on WAN Support DHCP server on LAN QoS with DiffServ Network tools in telnet server: including ping, trace route, telnet client 9.1.
