DP-100+ Multi-protocol Ethernet Print Server User’s Manual Rev.
0 TABLE OF C ONTENTS 0 ABOUT THIS GUIDE ..................................................................V 1 INTRODUCTION..........................................................................6 DP-100+ Print Server Features..................................................7 External Features .....................................................................8 Port Connectors ...................................................................... 9 Network Cable Connectors ..............................
Management and Diagnostics.................................................19 Environmental and Physical ...................................................19 4 PORT PINOUTS...................................................................... 21 Parallel Ports..........................................................................21 Serial Port...............................................................................22 5 INDEX .......................................................................
1 A BOUT T HIS G UIDE This manual describes the DP-100+ Ethernet Multiprotocol Print Server, including a description of the print server’s features, as well as the print server installation procedures and troubleshooting self-test results. For information about software configuration of the DP-100+ to allow it to be used with your network, consult the Print Server Administration User’s Guide included with your DP-100+.
1 2 INTRODUCTION The DP-100+ Print Server is a compact print server which connects to your Ethernet network anywhere you wish to locate printer services. It manages the flow of print files from your workstations or file servers to its connected printers, delivering print jobs to high-performance printers much faster than a file server or a PC acting as a print server can.
DP-100+ Multiprotocol Ethernet Print Server User’s Guide DP-100+ Print Server Features DP-100+ print servers improve network printing services in three ways: ♦ The DP-100+ picks up the workload of managing print file traffic to its connected printers. This provides workload relief to your file servers, and allows the file servers' full capacity to be used for file access or other direct services to network users.
Unix lpr/lpd (HP-UX, SunOS, Solaris, SCO, UnixWare, IBM AIX) Windows NT/2000/XP LPR for Windows 95/98/Me NetWare 5.x NDPS LPR remote printing ♦ NetBEUI Windows NT/2000, Windows 95/98/Me, Windows for Workgroups, Microsoft LAN Manager, IBM LAN Server ♦ AppleTalk MacOS EtherTalk Windows-based setup and administration software, PS Admin, is supplied with the DP-100+, making configuration and management quick and easy.
DP-100+ Multiprotocol Ethernet Print Server User’s Guide Port Connectors The DP-100+’s three printer ports are located on its rear panel. Two identical parallel ports are labeled LPT1 and LPT2; the single serial port is labeled COM. These printer ports are independently configurable using the PS Admin program or the print server’s telnet interface. (See the Print Server Administration User’s Guide for information about configuring the print server’s ports.
Network Cable Connectors The DP-100+ features two alternative network cable connectors for either twisted-pair 10Base-T cabling (using an RJ-45 connector) or thin coaxial 10Base2 cabling (using a BNC connector). Both of these network cable connectors are located on the DP-100+’s right side panel. DC Power Connector The DC power input connector is located on the DP-100+’s right side panel and is labeled DC 5V.
DP-100+ Multiprotocol Ethernet Print Server User’s Guide ◊ Steady or flashing green confirms that the DP-100+ is powered on. ◊ The indicator blinks off briefly to indicate that the DP100+ is transmitting to the network. ♦ Link/Rx ◊ Steady or flashing green confirms that the DP-100+ has a good connection to the Ethernet network. ◊ The indicator blinks off briefly to indicate that the DP100+ is receiving from the network.
Note when clicking each bracket into place, the round feet on the bottom of the device will line up with the round holes on the bracket. The brackets are designed to fit snugly in place. Please do not force them. The brackets are now ready for stacking devices. See the diagram below.
DP-100+ Multiprotocol Ethernet Print Server User’s Guide 2 3 U NPACKING AND INSTALLATION This chapter explains how to install your DP-100+ print server and connect it to the network. It also describes the print server self test indications, and tells how to wall-mount your print server. Unpacking and Inspecting the Print Server Carefully remove all items from the package.
♦ One Multi-language Quick Installation Guide If any item is missing, or if you find any damage or mismatch, promptly contact your dealer for assistance. Installing the DP-100+ WARNING: Configuration problems may result if the DP100+ is powered up without first establishing its network connection. Follow this procedure to avoid complications at the configuration stage. 1. Confirm proper operation of each of the printers to be connected to the DP-100+.
DP-100+ Multiprotocol Ethernet Print Server User’s Guide 5. While each printer is powered off, connect its tested and confirmed port with a like printer port of the DP-100+. If you are connecting fewer than three printers, then keep in mind that parallel- port connections are preferred for high-performance printers. 6. Switch on each connected printer. 7. Plug the DC power adapter’s DC output plug into the DC 5V power socket on the side panel of the DP-100+. 8.
Contact your dealer for correction of any LED problems before proceeding. The actual component tests immediately follow the LED tests. A normal (no fault) result is signaled by a series of three cycles of sequential flashing of the three LEDs, followed by a quiescent state with all three LEDs dark. If the self-test routine traps any component error, then following the LED tests the self-test will halt and the LED’s will continuously signal the error accordi ng to the following table.
DP-100+ Multiprotocol Ethernet Print Server User’s Guide Testing Your DP-100+ The PS Admin software includes a Print Test function for confirmation of printer cable connections and functions. That operational test can be completed after you have installed the PS Admin software, and have configured your DP-100+ and its ports. See the Testing Your Print Server section of the Print Server Administration User’s Guide.
A 4 P RODUCT S PECIFICATIONS Printer Connection Standards: IEEE 1284 bi -directional parallel interface, RS-232 Ports: Bi-directional 25-pin parallel ports × 2, 9-pin DTE serial port × 1 Parallel Port Bi-directional Communication: Hewlett-Packard PJL (Printer Job Language) supported Network Connection Network Standards: IEEE 802.
DP-100+ Multiprotocol Ethernet Print Server User’s Guide Network Connectors: BNC connector for 10BASE2 shielded pair connection, RJ-45 connector for 10BASE-T unshielded twisted pair connection (auto-switching) Network Protocols Ethernet Frame Types: 802.2, 802.
Dimensions: 190mm × 116.8mm × 30.9mm Weight: approx.
DP-100+ Multiprotocol Ethernet Print Server User’s Guide B 5 P ORT P INOUTS This appendix shows the pinouts of the DP-100+ parallel and serial printer ports. Parallel Ports The following table lists the pinouts of the print server’s 25-pin parallel port connector (identical to the connector used on most personal computers), as well as the 36-pin Centronics connector used on most printers. Signal names beginning with n are active -low signals.
25-pin 10 11 12 13 14 15 16 17 18-25 Centronics 10 11 12 13 14 32 31 36 16, 17, 19-30 Signal nAck Busy PError Select nAutoFd nFault nInit nSelectIn Ground Source Printer Printer Printer Printer Host Printer Host Host Serial Port The table below shows the pinout of the print server’s 9-pin RS232 serial port. The print server’s serial port is a DTE (Data Terminal Equipment) port, and should be connected to a DCE (Data Communications Equipment) serial port on your printer.
DP-100+ Multiprotocol Ethernet Print Server User’s Guide 6 INDEX 10Base2.........................................4, 7 packing list........................................ 6 10Base-T .......................................4, 7 pinout COM ..................................................3 parallel port .................................. 14 COM LED.......................................5, 9 serial port ..................................... 15 DC power adapter.........................
7 AUSTRALIA CANADA CHILE CHINA DENMARK EGYPT FRANCE GERMANY INDIA ITALY JAPAN RUSSIA SINGAPORE S. AFRICA SWEDEN TAIWAN U.K. U.S.A. O FFICES D-LINK AUSTRALASIA Unit 16, 390 Eastern Valley Way, Roseville, NSW 2069, Australia TEL: 61-2-9417-7100 FAX: 61-2-9417-1077 TOLL FREE: 1800-177-100 (Australia), 0800-900900 (New Zealand) URL: www.dlink.com.au E-MAIL: support@dlink.com.au, info@dlink.com.
TEL: 1-949-788-0805 FAX: 1-949-753-7033 INFO LINE: 1-800-326-1688 BBS: 1-949-455-1779, 1-949-455-9616 URL: www.dlink.com E-MAIL: tech@dlink.com, support@dlink.com LIMITED WARRANTY D-Link provides this limited warranty for its product only to the person or entity who originally purchased the product from D-Link or its authorized reseller or distributor.
upon return to D-Link of the defective Hardware. All Hardware (or part thereof) that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund.
THE REGISTRATION CARD MAY AFFECT THE WARRANTY FOR THIS PRODUCT. Submitting A Claim. Any claim under this limited warranty must be submitted in writing before the end of the Warranty Period to an Authorized D-Link Service Office. The claim must include a written description of the Hardware defect or Software nonconformance in sufficient detail to allow D-Link to confirm the same.
Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage; and Any hardware, software, firmware or other products or services provided by anyone other than D-Link.
GOVERNING LAW: This Limited Warranty shall be governed by the laws of the state of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This limited warranty provides specific legal rights and the product owner may also have other rights which vary from state to state.
Wichtige Sicherheitshinweise 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den spätern Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller zugelassen sind. 5. Das Gerät is vor Feuchtigkeit zu schützen. 6.
17. Wenden Sie sich mit allen Fragen die Service und Repartur betreffen an Ihren Servicepartner. Somit stellen Sie die Betriebssicherheit des Gerätes sicher. 18.Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden, Für einen Nennstrom bis 6A und einem Gerätegewicht grõßer 3kg ist eine Leitung nicht leichter als H05VV-F, 3G, 0.75mm2 einzusetzen. Trademarks Copyright 1999 D-Link Corporation. Contents subject to change without prior notice.
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.
Register by mail or online at http://www.dlink.com/sales/reg/ 8 R EGISTRATION C ARD Print, type or use block letters. Your name: Mr./Ms _____________________________________________________________________________ Organization: ________________________________________________ Dept.
__________________________________________________________________________________________
9
