DMC8 0 5 X Ver s i on1.
FCC Class A Certification This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications.
Introduction Thank you for choosing the DMC-805X, a 10G CX4 to 10G SFP+ Media Converter. The DMC-805X` converts 10G CX4 signals to 10G fiber signals. Comes with an SFP+ slot for user-selectable fiber transceivers and extends the network connection to various lengths depending on SFP+ transceiver capability. About DMC-805X The DMC-805X is a high performance 10G media converter which is flexible for distance extension on a server equipped with CX4 NIC or previous 10G switch built with 10G CX4 ports.
Product Features Compliance with IEEE802.3ak CX4 XAUI and IEEE802.
1. The ambient temperature should be between 32 and 104 degrees Fahrenheit (0 to 40 degrees Celsius). 2. The relative humidity should be less than 90 percent, non-condensing. 3. Surrounding electrical devices should not exceed the electromagnetic field (RFC) standards for IEC 801-3, Level 2 (3V/M) field strength. 4. Make sure that the equipment receives adequate ventilation. Do not block the ventilation holes on each side of the switch or the fan exhaust port on the side or rear of the equipment. 5.
Follow up the following steps to install the converter onto a carrier supplied with D-Link special designed chassis (DMC-1000): Step 1- Unscrew and pull out the media converter board. (Refer to figure 1) Step 2- Plug in the media board to any of the vacant slot. (Refer to figure 2) Step 3- Fit the converter onto the carrier and use the screw to secure it.
Monitoring the Converter through Management Module (DMC-1002) There is a management module named as DMC-1002 that can control this media converter through D-Link special designed chassis system (DMC-1000), this media converter can be controlled through Web Browser, SNMP and terminal emulation program. The management module will detect the default reset on the DIP switches and display out the status, also the management module (DMC-1002) can control the function through the chassis system (DMC-1000).
LED Indicator The LED indicators give you instant feedback on status of the converter: LEDs PWR (Power) CX4 SPF+ State Lights on Lights off Lights on Lights Blinking Lights off Lights on Lights Blinking Lights off Indication Power on Power off Linking Data transmitting and receiving Not Linking Linking Data transmitting and receiving Not Linking Refer to figure 4 to check the LED location on the front panel.
Link Pass Through Function (LLCF) Link Loss Carry Forward When a device connected to the converter and the CX4 XAUI lost the link connection, the converter’s fiber will disconnect the link of transmit, so that the other ends will know that there is a linkage error on this end. And when the Fiber line lost the link, the converter’s CX4 XAUI will be disconnected, and the other end will know that there is linkage problem exist. The LLCF setting is always Enable on this converter.
Link Pass Through Function (LLR) Link Loss Return When a device connected to the converter and the fiber line lot the link, the converter’s fiber will disconnect the link of transmit. There is a switch to enable or disable the function of the media converter.
Switch There is one pin DIP switch on the module which defines as switch 1: Switch 1: LLR When the switch was turned to “On”, it means that the LLR was enabled and “Off” for disabled. Note: When using two converters, don’t enable the both devices’ LLR function at the same time.
Specifications Standards: Data Transfer Rate: Duplex Mode: IEEE802.3ak 10GBASE-CX4 IEEE802.
CX4 Cable 10GBASE-CX4 XAUI 4-lane PCS (Clause 48) and copper cabling similar to that used by InfiniBand technology, up to 15m DIP Switch Bit 1: Off: LLR disable(default) On: LLR enable Dimensions L120 × W88 × H25 mm Power External power adapter 12V/0.5A Temperture: Storage: -10°C ~ 70°C (14 ~ 158º F) Humidity: 10% ~90% non-condensing Power Consumption: 3.4 Watts Max.
Notes 14
Notes 15
Ver. 1.
