DMC-1002 SNMP Module for Chassis-Based Media Converter Manual Rev. 01 (JUN.
TABLE OF C ONTENTS ABOUT THIS GUIDE .................................................................. 2 FEATURES......................................................................................................2 UNPACKING ...................................................................................................2 CONFIGURING THE SYSTEM .......................................... 3 THE MEDIA CONVERTER CHASSIS SYSTEM ...................................................
A BOUT T HIS G UIDE This manual shows you how to configuring your DMC-1002 SNMP Module for Chassis-Based Media Converter. Features 9 9 9 9 Compliant with IEEE802.
C ONFIGURING T HE S YSTEM This chapter provides network managers and system administrators with information about how to configure the Media Converter Chassis system. The reader of this document should be knowledgeable about network devices, device configuration, network management, and Internet browsers. The user is assumed to be a network administrator or manager with an understanding of network operations.
Configure through Web browser The Media Converter chassis system is accessible using a Web browser (IE explorer, Netscape Communications, etc.) to open up the chassis monitoring system. The default IP Address for the chassis system is “192.168.1.1”, and the default Login name and password is both “root”. Configuration via Serial Port The Media Converter chassis system can be accessible using a terminal or terminal emulator attached to the RS232 serial port on the Switch too.
5. The default Login name and password is both “root”. Support SNMP Management The Media Converter Management Module support SNMP management. LED Indicators The LED indicators of the Switch include Power, ALERT, HTTP, ICQ, SMTP, SPEED, LINK/ACT and FDX/COL. The following shows the LED indicators for the Switch along with an explanation of each indicator. DMC- 1000i Power On: Lights green when the power is inserted. Power Fail: Lights Amber when the power is inserted and it is fail.
Link/Act: Lights green when link to networking Ethernet and blinks green for activity. M ANAGEMENT S ETTING T HROUGH W EB B ROWSER 1 Main Menu 1-1 System Function Figure (1) Main Menu There are four items in System Function menu, “Software Reboot, Factory Reset, Image Update and Configuration Update. (Figure 2) 1-2 Configuration There are three items in Configuration menu, “General Configuration, System Configuration and SNMP Configuration.
Figure (2) Configuration 1-1-1 Software Reboot To reboot for the software setting. 1-1-2 CPU Factory Reset This function is to set the CPU (DMC-1002) back to the default setting in case of the messy setting. 1-1-3 Factory Reset This function is to set both CPU (DMC-1002) and all system (all smart device installed in chassis) back to the default setting in case of the messy setting. 1-1-4 Image Update The section is to set the TFTP Server IP Address first, and the default address was set to “192.168.1.2”.
While the file is uploading to the system, it will appear a warning sign. (Figure 3.2) Figure (3.1) Figure (3.
1-1-5 Configuration Update Figure (4) The section is explaining how to upload and download the configure setting of the module. The Configuration Upload is to restore a setting file to the management module. The Configuration Download is to backup the setting from the management module.
Figure (5) Hardware revision: noted the version of the hardware. BIOS revision: noted the version of the BIOS. Firmware revision: noted the version of the firmware. Change Password: the changing of the admit password. Confirm Password: to confirm the setting of admit password. System Name: to authorize the device system name. Location: to show the device where it is located. Refresh time: to set the refreshing time of the device through the web.
default IP is “192.168.1.1”. Subnet Mask: to set the Subnet Mask, the default is “255.255.255.0”. Default Gateway: to set the gateway address, the default is “192.168.1.254”. NOTE: After configuring the system device, need to press the save button to save the setting. 1-2-3 SNMP Configuration Figure (7) Get Community Name: to get the device community name (default = public). Set Community Name: to set the device community name (default = private).
Cold Start trap: to set the trap for rebooting the device (default = enable). Authentication Fail Trap: to set the warning trap when the community name of the device and workstation are different (default = enable). Power Fail Trap: to set the Power Fail Trap (default = enable). Fan Fail Trap: to set the fan fail trap (default = enable). MC Plug-in Trap: to set the trap of the Media Converter module if it is plugged in (default = enable).
M ANAGEMENT S ETTING T HROUGH T ERMINAL E MULATOR 2 Main Menu Figure (8) 2-1 System Function There are three items in System Function menu, “Software Reboot, Factory Reset, Image Update. (Figure 9) Figure (9) 2-1-1 Software Reboot To reboot for the software setting.
This function is to set the device back to the default setting in case of the messy setting. 2-1-3 Image Update Figure (10) The section is to set the TFTP Server IP Address first, and the default address was set to “192.168.1.2”. The Image File can be updated by uploading the image file from the TFTP server. (Figure 10) Note: The content of the image file will write the whole firmware of the management module, please be sure that the image file is correct.
There are four items in the Configuration menu, “General Configuration, System Configuration, Media Converter Chassis, Media Converters Status and Media Converters Setting. (Figure 11) 2-2-1 General Configuration Figure (12) Hardware revision: noted the version of the hardware. BIOS revision: noted the version of the BIOS. Firmware revision: noted the version of the firmware. Change Password: the changing of the admit password. Confirm Password: to confirm the setting of admit password.
Figure (13) MAC Address: will show out the MAC address of the device. IP Address: to allocate an IP address for the device, the default IP is “192.168.1.1”. Subnet Mask: to set the Subnet Mask, the default is “255.255.255.0”. Default GW: to set the gateway address, the default is “192.168.1.254”. NOTE: After configuring the system device, need to press the save button to save the setting.
Figure (14) The screen will show out the power status of the chassis system. V stands for “yes” and X stands for “No”. Plug in: indicates if Power 1 or 2 was plugged in or not. Power Fail: indicates if the Power 1 or 2 is fail or not. Fan Fail: indicates if the Fan 1 or 2 is fail or not. 2-2-4 Media Converters Status Figure (15.
media converter. 2-2-4 Media Converters Status Figure (15.2) To control the linkage of each media converter. 2-3 SNMP Configuration Figure (16) Get Community Name: (default = public). to get the device community name Set Community Name: to set the device community name (default = private).
Trap Community Name: to authorize the device trap community name (default = public). Trap Host IP Address: to set the trap host IP address (same as monitoring station IP address). Cold Start trap: to set the trap for rebooting the device (default = enable). Authentication Fail Trap: to set the warning trap when the community name of the device and workstation are different (default = enable). Power Fail Trap: to set the Power Fail Trap (default = enable).
T ECHNICAL S PECIFICATIONS General Standards IEEE 802.3 10BASE-T; IEEE 802.3u 100BASE-TX Protocol CSMA/CD Data Transfer Rate 100Mbps (Half-duplex) 200Mbps (Full-duplex) Topology Star Network Cables 10BASE-T – 2-pair UTP Cat. 3,4,5, up to 100 m (328 ft) 100BASE-TX -2-pair UTP Cat.
