DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Information in this document is subject to change without notice. Reproduction of this document in any manner, without the written permission of the D-Link Corporation, is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of the D-Link Corporation; Microsoft and Windows are registered trademarks of the Microsoft Corporation.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Table of Contents 1. INTRODUCTION ................................................................................................................................................................. 1 AUDIENCE ............................................................................................................................................................................................. 1 OTHER DOCUMENTATION ..........................
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch IPv6 Interface ............................................................................................................................................................................... 21 PORT CONFIGURATION .......................................................................................................................................................................... 21 Port Settings ..............................................
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch MAC Address Table Settings ........................................................................................................................................................ 48 MAC Address Table ...................................................................................................................................................................... 49 VLAN .......................................................................
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch RADIUS Global Settings ............................................................................................................................................................... 93 RADIUS Server Settings ................................................................................................................................................................ 93 RADIUS Statistic .........................................................
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Group Details ............................................................................................................................................................................. 119 IP-CAMERA INFORMATION ................................................................................................................................................................... 120 NVR INFORMATION .................................................
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch 1. Introduction This manual’s descriptions are based on the software release 1.20. All software functions of the DIS200G Series switches can be managed, configured and monitored via the embedded web-based (HTML) interface. Manage the Switch from remote stations anywhere on the network through a standard browser. The browser acts as a universal access tool and can communicate directly with the Switch using the HTTP protocol.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Notes, Notices, and Cautions Below are examples of the three types of indicators used in this manual. When administering your switch using the information in this document, you should pay special attention to these indicators. Each example below provides an explanatory remark regarding each type of indicator. NOTE: A note indicates important information that helps you make better use of your device.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch 2. Web-based Switch Configuration Management Options Connecting using the Web User Interface Logging onto the Web Manager Smart Wizard Web User Interface (Web UI) Management Options The Switch provides multiple access platforms that can be used to configure, manage and monitor networking features available on the Switch. Currently there are three management platforms available and they are described below.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Figure 2-1 Displays entering the IP address in Internet Explorer This will open the user authentication window, as seen below. Figure 2-2 User Authentication window Enter the User Name and Password in the corresponding fields and click Login. The default username is admin and the default password is admin. This will open the Web-based user interface. The Switch’s management features available in the web-based manager are explained below.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Smart Wizard After a successfully connecting to the Web User Interface for the first time, the Smart Wizard embedded Web utility will be launched. This wizard will guide the user through basic configuration steps that is essential for first time connection to the Switch. Step 1 - Web Mode The Switch supports two Web Modes, Standard Mode and Surveillance Mode.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Step 2 – System IP Information In this window, the user can configure the IP address assignment method, the static IP address, Netmask and Gateway address. NOTE: The Switch will probe for surveillance devices every 30 seconds. If a surveillance device is not in the same subnet as the switch, it will not be discovered automatically.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Step 3 – User Accounts Settings In this window, the user can configure the user password of ‘admin’ account. Figure 2-5 Password window The fields that can be configured are described below: Parameter Description Password Enter the new password for the user account here. Confirm Password Enter the new password again for confirmation here. Tick the Ignore the wizard next time option to skip the Smart Wizard on the next login.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Step 4 – SNMP Settings In this window, the user can enable or disable the SNMP function. Figure 2-7 SNMP window Figure 2-6 SNMP window The fields that can be configured are described below: Parameter Description SNMP Select the Enabled option to enable the SNMP function. Select the Disabled option to disable the SNMP function. Tick the Ignore the wizard next time option to skip the Smart Wizard on the next login.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Web User Interface (Web UI) By clicking the Exit button in the Smart Wizard, you will enter the Web-based Management interface. Areas of the User Interface The figure below shows the Web UI in the Standard Mode. Three distinct areas that divide the user interface, as described in the table.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Surveillance Mode After accessing the Web UI in the Surveillance Mode,the following will be displayed:. Figure 2-8 Web UI (Surveillance Mode) The following Areas can be observed in the above window: Parameter Description AREA 1 Select the folder or window to display. Open folders and click the hyperlinked window buttons and subfolders contained within them to display windows.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch 3. Save and Tools Save Configuration Firmware Information Firmware Upgrade & Backup Configuration Restore & Backup Log Backup Ping Reset Reboot System Save Configuration This window is used to save the running configuration to the start-up configuration or the file system of the Switch. This is to prevent the loss of configuration in the event of a power failure.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Firmware Upgrade & Backup Firmware Upgrade from HTTP This window is used to initiate a firmware upgrade from a local PC using HTTP.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Firmware Backup to HTTP This window is used to initiate a firmware backup to a local PC using HTTP. To view the following window, click Tools > Firmware Upgrade & Backup > Firmware Backup to HTTP, as shown below: Figure 3-5 Firmware Backup to HTTP window The fields that can be configured are described below: Parameter Description Source Specify the firmware image ID to be backup. Click the Backup button to initiate the firmware backup.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Configuration Restore & Backup Configuration Restore from HTTP This window is used to initiate a configuration restore from a local PC using HTTP.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Take effect after the next boot (startup-config) Specify this radio button to restore and overwrite the start-up configuration file on the Switch. Click the Restore button to initiate the configuration restore. Configuration Backup to HTTP This window is used to initiate a configuration file backup to a local PC using HTTP.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Log Backup Log Backup to HTTP This window is used to initiate a system log backup to a local PC using HTTP. To view the following window, click Tools > Log Backup > Log Backup to HTTP, as shown below: Figure 3-11 Log Backup to HTTP window Click the Backup button to initiate the system log backup. Log Backup to TFTP This window is used to initiate a system log backup to a TFTP server.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Ping Ping is a small program that sends ICMP Echo packets to the IP address you specify. The destination node then responds to or “echoes” the packets sent from the Switch. This is very useful to verify connectivity between the Switch and other nodes on the network.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Reset This window is used to reset the Switch’s configuration to the factory default settings. To view the following window, click Tools > Reset, as shown below: Figure 3-15 Reset window Select the The Switch will be reset to its factory defaults including IP address, and then will save, reboot option to reset the Switch’s configuration to its factory default settings.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch 4. System Device Information System Information Settings Port Configuration PoE System Log Time Time Profile Device Information In this window, the Device Information, CPU, and Used status are displayed. It appears automatically when you log in the Switch. To return to the Device Information window after viewing other windows, click the DIS-200G-12PS/12PSW link.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch IPv4 Interface This window is used to view and configure the IPv4 interface settings. To view the following window, click System > System Information Settings > IPv4 Interface, as shown below: Figure 4-3 IPv4 Interface window The fields that can be configured are described below: Parameter Description Get IP From Select the get IP from option here. Options to choose from are Static and DHCP.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch IPv6 Interface This window is used to view and configure the IPv6 interface settings. To view the following window, click System > System Information Settings > IPv6 Interface, as shown below: Figure 4-4 IPv6 Interface window The fields that can be configured are described below: Parameter Description IPv6 State Click to enable or disable the IPv6 feature.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Parameter Description From Port / To Port Select the appropriate port range used for the configuration here. State Select this option to enable or disable the physical port here. MDIX Select the Medium Dependent Interface Crossover (MDIX) option here. Options to choose from are Auto, Normal, and Cross. Auto - Select this option for auto-sensing of the optimal type of cabling. Normal - Select this option for normal cabling.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Jumbo Frame This window is used to view and configure the Jumbo Frame size and settings. The Switch supports jumbo frames. Jumbo frames are Ethernet frames with more than 1,518 bytes of payload. The Switch supports jumbo frames with a maximum frame size of up to 9600 bytes.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch PoE(DIS-200G-12PS and DIS-200G-12PSW Only) This switch support Power over Ethernet (PoE) as defined by the IEEE 802.3af and 802.3at. All ports can support PoE up to 30W. The Switch follows the standard PSE (Power Sourcing Equipment) pin-out Alternative A, whereby power is sent out over pins 1, 2, 3 and 6. The Switches work with all D-Link 802.3af capable devices.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch PoE Status This window is used to configure the description, and display the PoE status of each port. To view the following window, click System > PoE > PoE Status, as shown below: Figure 4-8 PoE Status window PoE Configuration This window is used to configure the PoE port.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Time Profile Select the name of the time range to determine the activation period. Click the Delete Time Profile button to clear the setting in the corresponding Time Range field. Click the Apply button to accept the changes made. PD Alive This window is used to configure the PD Alive function for PDs connected to the PoE ports. The ping function is used to check if PDs, connected to the PoE ports, are active or not.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch System Log System Log Settings This window is used to view and configure the system’s log settings. To view the following window, click System > System Log > System Log Settings, as shown below: Figure 4-11 System Log Settings window The fields that can be configured for Global State are described below: Parameter Description System log Select this option to enable or disable the global state.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Severity Select the severity value of the type of information that will be logged. Options to choose from are Errors, Warning, Notice and Informational. Facility Select the facility value here. Options to choose from are 0 to 7. Click the Apply button to accept the changes made. System Log This window is used to view and clear the system log.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Time Zone Settings This window is used to configure time zones and Daylight Savings Time settings for SNTP. To view the following window, click System > Time > Time Zone Settings, as shown below: Figure 4-15 Time Zone Settings window The fields that can be configured are described below: Parameter Description Summer Time State Select the summer time setting. Options to choose from are Disabled, Recurring Setting, and Date Setting.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch From: Day of the Week Select the day of the week that summer time will start. From: Month Select the month that summer time will start. From: Time (HH:MM) Select the time of the day that summer time will start. To: Week of the Month Select week of the month that summer time will end. To: Day of the Week Select the day of the week that summer time will end. To: Month Select the month that summer time will end.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Poll Interval Enter the synchronizing interval in seconds. The value is from 30 to 99999 seconds. The default interval is 720 seconds. Click the Apply button to accept the changes made. The fields that can be configured for SNTP Server Setting are described below: Parameter Description IPv4 Address Enter the IP address of the SNTP server which provides the clock synchronization. Click the Apply button to accept the changes made.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch 5. Management User Account Settings Password Encryption SNMP RMON HTTP/HTTPS D-Link Discovery Protocol User Account Settings This window is used to create and configure the user accounts. The active user account sessions can be viewed. The pre-defined user account privilege levels supported by this switch is: Administrator - Privilege read-write.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Password Encryption This window is used to configure the encryption of the password before stored in the configuration file. To view the following window, click Management > Password Encryption, as shown below: Figure 5-2 Password Encryption Settings window The fields that can be configured are described below: Parameter Description Password Encryption State Choose the enable or disable password encryption.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch SNMP Simple Network Management Protocol (SNMP) is an OSI Layer 7 (Application Layer) designed specifically for managing and monitoring network devices. SNMP enables network management stations to read and modify the settings of gateways, routers, switches, and other network devices. Use SNMP to configure system features for proper operation, monitor performance and detect potential problems in the Switch, switch group or network.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The Switch incorporates a flexible SNMP management for the switching environment. SNMP management can be customized to suit the needs of the networks and the preferences of the network administrator. Use the SNMP V3 menus to select the SNMP version used for specific tasks. The Switch supports the Simple Network Management Protocol (SNMP) versions 1, 2c, and 3.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Coldstart Tick this option to control the sending of SNMP coldStart notifications. Warmstart Tick this option to control the sending of SNMP warmStart notifications. Click the Apply button to accept the changes made. SNMP View Table Settings This window is used to assign views to community strings that define which MIB objects can be accessed by a remote SNMP manager.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch SNMP Community Table Settings This window is used to create an SNMP community string to define the relationship between the SNMP manager and an agent. The community string acts like a password to permit access to the agent on the Switch. The characteristics can be associated with the community string: Read/write or read-only level permission for the MIB objects accessible to the SNMP community.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch SNMP Group Table Settings An SNMP Group created with this table maps SNMP users (identified in the SNMP User Table) to the views created in the previous window.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Read View Name Enter the read view name that the group user can access. Write View Name Enter the write view name that the group user can access. Notify View Name Enter a write view name that the group user can access. The notify view describes the object that can be reported its status via trap packets to the group user. Click the Add button to add a new entry based on the information entered.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Parameter Description User Name Enter an alphanumeric string of up to 32 characters. This is used to identify the SNMP users. Group Name Enter the SNMP group name to which the user belongs. The syntax is general string that does not allow spaces. SNMP Version Select the SNMP version. Options to choose from are v1, v2c, and v3. SNMP V3 Encryption When selecting v3 in the SNMP Version drop-down list, this option is available.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The fields that can be configured are described below: Parameter Description Host IPv4 Address Enter the IPv4 address of the SNMP notification host. SNMP Version Select the security model here. Options to choose from are SNMPv1, SNMPv2c, and SNMPv3. SNMPv1 - Select to allow the group user to use the SNMPv1 security model. SNMPv2c - Select to allow the group user to use the SNMPv2c security model.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch RMON RMON Global Settings This window is used to enable or disable remote monitoring (RMON) for the rising and falling alarm trap feature for the SNMP function on the Switch.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch After clicking the Show Detail button, the following window will appear. Figure 5-12 RMON Statistics Table window Click the Back button to return to the previous window. RMON History Settings This window is used to configure and display RMON MIB history statistics gathering on the specified port.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Figure 5-14 RMON History Table window Click the Back button to return to the previous window. RMON Alarm Settings This window is used to configure and display alarm entries to monitor an interface. To view the following window, click Management > RMON > RMON Alarm Settings, as shown below: Figure 5-15 RMON Alarm Settings window The fields that can be configured are described below: Parameter Description Index Enter the alarm index.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch RMON Event Settings This window is used to configure and display event entries. To view the following window, click Management > RMON > RMON Event Settings, as shown below: Figure 5-16 RMON Event Settings The fields that can be configured are described below: Parameter Description Index Enter the index of the alarm entry between 1 and 65535. Description Enter a description for the RMON event entry.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch HTTP/HTTPS This window is used to configure the web server running on HTTP or HTTPS protocol. To view the following window, click Management > HTTP/HTTPS, as shown below: Figure 5-18 HTTP/HTTPS window The fields that can be configured for HTTP/HTTPS are described below: Parameter Description WEB Session Select the protocol for web server. Web Session Timeout Enter the session timeout value for web session.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch 6. Layer 2 Features FDB VLAN Spanning Tree Loopback Detection Link Aggregation L2 Multicast Control LLDP FDB Static FDB Unicast Static FDB This window is used to view and configure the static unicast forwarding settings on the Switch.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Multicast Static FDB This window is used to view and configure the multicast static FDB settings. To view the following window, click L2 Features > FDB > Static FDB > Multicast Static FDB, as shown below: Figure 6-2 Multicast Static FDB window The fields that can be configured are described below: Parameter Description From Port / To Port Select the appropriate port range used for the configuration here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Figure 6-4 MAC Address Table Settings (MAC Address Learning) window The fields that can be configured are described below: Parameter Description From Port / To Port Select the range of ports that will be used for this configuration here. State Select to enable or disable the MAC address learning function on the ports specified here. Click the Apply button to accept the changes made.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch VLAN VLAN Configuration Wizard This window is used to guide the user to create a new VLAN or configure an existing VLAN on the Switch. Step 1 – Select VLAN To view the following window, click L2 Features > VLAN > VLAN Configuration Wizard, as shown below: Figure 6-6 VLAN Configuration Wizard (Select VLAN) window The fields that can be configured are described below: Parameter Description Create VLAN VID Select and enter a new VLAN ID.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Figure 6-8 VLAN Configuration Wizard (Configure VLAN) Window The fields that can be configured are described below: Parameter Description VLAN Name Enter the name of the VLAN. Tagged Click to designate the post as tagged. Click the All button to select all ports. Untagged Click to designate the port as untagged. Click the All button to select all ports Not Member Click to allow an individual port to be specified as a non-VLAN member.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch 802.1Q VLAN This window is used to view and configure the VLAN settings on this switch. To view the following window, click L2 Features > VLAN > 802.1Q VLAN, as shown below: Figure 6-10 802.1Q VLAN window The fields that can be configured for 802.1Q VLAN are described below: Parameter Description VID List Enter the VLAN ID list that will be created here. Click the Apply button to accept the changes made.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch GVRP GVRP Global This window is used to view and configure the GARP VLAN Registration Protocol (GVRP) global settings. To view the following window, click L2 Features > VLAN > GVRP > GVRP Global, as shown below: Figure 6-12 GVRP Global window The fields that can be configured are described below: Parameter Description Asymmetric VLAN State Select this option to enable or disable the global GVRP state here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Figure 6-13 GVRP Port window Guide The fields that can be configured are described below: Parameter Description From Port / To Port Select the appropriate port range used for the configuration here. GVRP Status Select this option to enable or disable the GVRP port status. This enables the port to dynamically become a member of a VLAN. By default, this option is disabled. Click the Apply button to accept the changes made.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch used. Advertise VID List Enter the advertised VLAN ID list here. Click the Apply button to accept the changes made. GVRP Forbidden VLAN This window is used to view and configure the GVRP forbidden VLAN settings.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Asymmetric VLAN This window is used to configure the asymmetric VLAN function. To view the following window, click L2 Features > VLAN > Asymmetric VLAN, as shown below: Figure 6-16 Asymmetric VLAN window The fields that can be configured are described below: Parameter Description Asymmetric VLAN State Select this option to enable or disable the asymmetric VLAN function Click the Apply button to accept the changes made.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch More detailed information about the VLAN of the specific interface is displayed. Click the Back button to return to the previous window. After click the Edit button, the following window will appear. This is a dynamic window that will change when a different VLAN Mode was selected. When Access was selected as the VLAN Mode, the following page will appear.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The fields that can be configured are described below: Parameter Description VLAN Mode Select the VLAN mode option here. Options to choose from are Access, Hybrid, and Trunk. Acceptable Frame Select the acceptable frame behavior option here. Options to choose from are Tagged Only, Untagged Only, and Admit All. Ingress Checking Select the check box to enable or disable the ingress checking function.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch value must be between 1 and 4094. Action Select the action that will be taken here. Options to choose from are All, Add, Remove, and Except. Allowed VLAN Range Enter the allowed VLAN range information here. Click the Apply button to accept the changes made. Click the Back button to return to the previous window.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Auto Surveillance VLAN Auto Surveillance Properties This window is used to configure the auto surveillance VLAN global settings and display the ports surveillance VLAN information.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Log State Set the Surveillance VLAN log state Click the Apply button to accept the changes made. The fields that can be configured for Port Settings are described below: Parameter Description From Port / To Port Select the appropriate port range used for the configuration here. State Select this option to enable or disable the state of the port. Click the Apply button to accept the changes made.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch ONVIF IP-Camera Information This window is used to display ONVIF IP camera information. Figure 6-24 Auto Surveillance VLAN Summary window To view the following window, click L2 Features > VLAN > Auto Surveillance VLAN > ONVIF IPCamera Information, as shown below: Figure 6-25 ONVIF IP-Camera Information window Click the IP Address hyperlink to connect to the Web Interface of the IP camera.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Click the Back button to discard the changes made and return to the previous window. Click the Apply button to accept the changes made. ONVIF NVR Information This window is used to display ONVIF Network Video Recorder (NVR) information.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Voice VLAN Voice VLAN Global Voice VLAN is a VLAN used to carry voice traffic from IP phone. Because the sound quality of an IP phone call will be deteriorated if the data is unevenly sent, the quality of service (QoS) for voice traffic shall be configured to ensure the transmission priority of voice packet is higher than normal traffic. The switches determine whether a received packet is a voice packet by checking its source MAC address.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Figure 6-32 Voice VLAN Port window The fields that can be configured are described below: Parameter Description From Port / To Port Select the appropriate port range used for the configuration here. State Select this option to enable or disable the state of the port. Mode Select the mode of the port. Options to choose from are Auto Untagged, Auto Tagged, and Manual. Click the Apply button to accept the changes made.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Voice VLAN OUI This window is used to configure the user-defined voice traffic’s OUI. The OUI is used to identify the voice traffic. There are a number of pre-defined OUIs. The user can further define the user-defined OUIs if needed. The user-defined OUI cannot be the same as the pre-defined OUI.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Spanning Tree This Switch supports three versions of the Spanning Tree Protocol: 802.1D-1998 STP, 802.1D-2004 Rapid STP, and 802.1Q- 2005 MSTP. 802.1D-1998 STP will be familiar to most networking professionals. However, since 802.1D-2004 RSTP and 802.1Q-2005 MSTP have been recently introduced to D -Link managed Ethernet switches, a brief introduction to the technology is provided below followed by a description of how to set up 802.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch by Ethernet switches. The basic function and much of the terminology is the same as STP. Most of the settings configured for STP are also used for RSTP. This section introduces some new Spanning Tree concepts and illustrates the main differences between the two protocols.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch STP Global Settings This window is used to view and configure the STP global settings. To view the following window, click L2 Features > Spanning Tree > STP Global Settings, as shown below: Figure 6-35 STP Global Settings window The field that can be configured for Spanning Tree State is described below: Parameter Description Spanning Tree State Select this option to enable or disable the STP global state here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Click the Apply button to accept the changes made. The fields that can be configured for BPDU Forward are described below: Parameter Description BPDU Forward Select to enable or disable BPDU forwarding. If enabled, the received STP BPDU will be forwarded to all VLAN member ports in the untagged form. By default, this option is Disabled. Click the Apply button to accept the changes made.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch MST Configuration Identification This window is used to view and configure the MST configuration identification settings. These settings will uniquely identify a multiple spanning tree instance set on the Switch. The Switch initially possesses one CIST, or Common Internal Spanning Tree, of which the user may modify the parameters for but cannot change the MSTI ID for, and cannot be deleted.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch STP Instance This window is used to view and configure the STP instance settings. To view the following window, click L2 Features > Spanning Tree > STP Instance, as shown below: Figure 6-38 STP Instance window Click the Edit button to re-configure the specific entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch ERPS (G.8032) ERPS This window is used to view and configure Ethernet Ring Protection Switching (ERPS) settings. To view the following window, click L2 Features > ERPS (G.8032) > ERPS, as shown below: Figure 6-40 ERPS window The fields that can be configured are described below: Parameter Description Ring Name Enter the Ethernet Ring Protection (ERP) instance’s name here. This name can be up to 32 characters long.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Select the Specify radio button to configure this parameter as per normal. Select the None radio button to revert this parameter to the default setting. Click the Back button to discard the changes made and return to the previous window. Click the Apply button to accept the changes made. After clicking the ERPS Brief tab, the following page will appear.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch ERP instance should be identical. Select the Specify radio button to configure this parameter as per normal. Select the None radio button to revert this parameter to the default setting. Profile Name Select the checkbox and enter the G.8032 profile’s name here that will be associated with this ERP instance. Multiple ERP instances can be associated with the same G.8032 profile.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Figure 6-45 ERPS Profile window The fields that can be configured are described below: Parameter Description Profile Name Enter the G.8032 profile’s name here. This name can be up to 32 characters long. Multiple ERP instances can be associated with the same G.8032 profile. The instances associated with the same profile protect the same set of VLANs, or the VLANs protected by one instance are a subset of LANs protected by another instance.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Loopback Detection The Loopback Detection (LBD) function is used to detect the loop created by a specific port. This feature is used to temporarily shut down a port on the Switch when a CTP (Configuration Testing Protocol) packet has been looped back to the Switch. When the Switch detects CTP packets received from a port, this signifies a loop on the network. The Switch will automatically block the port and send an alert to the administrator.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Link Aggregation Understanding Port Trunk Groups Port trunk groups are used to combine a number of ports together to make a single high-bandwidth data pipeline. The Switch supports up to 6 port trunk groups with 1 to 8 ports in each group. Figure 6-48 Example of Port Trunk Group The Switch treats all ports in a trunk group as a single port.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The Spanning Tree Protocol will treat a link aggregation group as a single link, on the switch level. On the port level, the STP will use the port parameters calculation of port cost and in determining the state of the link aggregation group. If two redundant link aggregation groups are configured on the Switch, STP will block one entire group; in the same way STP will block a single port that has a redundant link.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch After clicking the Channel Detail button, the following page will be available. Figure 6-50 Port Channel window Click the Back button to return to the previous window.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch L2 Multicast Control IGMP Snooping Internet Group Management Protocol (IGMP) snooping allows the Switch to recognize IGMP queries and reports sent between network stations or devices and an IGMP host. IGMP Snooping Settings In order to use IGMP Snooping it must first be enabled for the entire Switch under IGMP Global Settings at the top of the window.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The fields that can be configured for VLAN Querier Status Settings are described below: Parameter Description VID Enter a VLAN ID from 1 to 4094, and select to enable or disable IGMP snooping querier on the VLAN. Click the Apply button to accept the changes made.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch MLD Snooping Multicast Listener Discovery (MLD) Snooping is an IPv6 function used similarly to IGMP snooping in IPv4. It is used to discover ports on a VLAN that are requesting multicast data.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch MLD Snooping Settings This window is used to configure the MLD snooping settings. To view the following window, click L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Settings, as shown below: Figure 6-53 MLD Snooping Settings window The field that can be configured for Global Settings is described below: Parameter Description Global State Select this option to enable or disable MLD snooping global state.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch MLD Snooping Groups Settings This window is used to configure and view the MLD snooping static group, and view MLD snooping group.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch LLDP LLDP Global Settings This window is used to configure the LLDP global settings.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch 7. Quality of Service (QoS) 802.1p Priority Port Rate Limiting Port Trust State 802.1p Priority This window is used to view and configure the port’s scheduler method and default CoS settings. To view the following window, click QoS > 802.1p Priority, as shown below: Figure 7-1 802.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Click the Apply button to accept the changes made. The fields that can be configured in Port Default CoS are described below: Parameter Description From Port / To Port Select the appropriate port range used for the configuration here. Default CoS Select the default CoS option for the port(s) specified here. Options to choose from are Low, Medium, High, and Highest. Click the Apply button to accept the changes made.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Port Trust State This window is used to view and configure port trust state settings To view the following window, click QoS > Port Trust State, as shown below: Figure 7-3 Port Trust State window The fields that can be configured are described below: Parameter Description From Port / To Port Select the appropriate port range used for the configuration here. Trust State Select the port trust state option here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Click the Apply button to accept the changes made 8. Security Port Security RADIUS Safeguard Engine Traffic Segmentation Storm Control DoS Attack Prevention Zone Defense SSL Web-based Access Control Port Security Port Security Global Settings This window is used to view and configure the port security global settings.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Port Security Port Settings This window is used to view and configure the port security port settings. To view the following window, click Security > Port Security > Port Security Port Settings, as shown below: Figure 8-2 Port Security Port Settings window The fields that can be configured are described below: Parameter Description From Port / To Port Select the appropriate port range used for the configuration here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Port Security Address Entries This window is used to view, clear and configure the port security address entries. To view the following window, click Security > Port Security > Port Security Address Entries, as shown below: Figure 8-3 Port Security Address Entries window The fields that can be configured are described below: Parameter Description Port Select the port used for the configuration here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch RADIUS RADIUS Global Settings This window is used to view and configure the RADIUS global settings. To view the following window, click Security > RADIUS > RADIUS Global Settings, as shown below: Figure 8-4 RADIUS Global Settings window The fields that can be configured are described below: Parameter Description Dead Time Enter the dead time value here. This value must be between 1 and 1440 minutes. By default, this value is 0 minutes.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The fields that can be configured are described below: Parameter Description IP Address Enter the RADIUS server’s IPv4 address here. IPv6 Address Enter the RADIUS server’s IPv6 address here. Authentication Port Enter the authentication port number used here. This value must be between 0 and 65535. By default, this value is 1812. If no authentication is used, use the value 0. Accounting Port Enter the accounting port number used here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Safeguard Engine Periodically, malicious hosts on the network will attack the Switch by utilizing packet flooding (ARP Storm) or other methods. These attacks may increase the switch’s CPU load beyond its capability. To alleviate this problem, the Safeguard Engine function was added to the Switch’s software.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Traffic Segmentation Settings This window is used to view and configure the traffic segmentation settings. When the traffic segmentation forwarding domain is specified, packets received by the port will be restricted in Layer 2 packet forwarding to interfaces within the domain. When the forwarding domain of a port is empty, Layer 2 forwarding for packets received by the port is not restricted.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The fields that can be configured for Storm Control Settings are described below: Parameter Description Type Select the type of storm attack that will be controlled here. Options to choose from are Broadcast, Multicast, and Unicast.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch DoS Attack Prevention Settings This window is used to view and configure the Denial-of-Service (DoS) attack prevention settings. The following well-known DoS types which can be detected by most switches: • Land Attack: This type of attack involves IP packets where the source and destination address are set to the address of the target device. It may cause the target device to reply to itself continuously.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Click the Apply button to accept the changes made. Zone Defense This window is used to view and configure the zone defense settings.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch SSH Secure Shell (SSH) is a program allowing secure remote login and secure network services over an insecure network. It allows a secure login to remote host computers, a safe method of executing commands on a remote end node, and will provide secure encrypted and authenticated communication between two non-trusted hosts. SSH, with its array of unmatched security features is an essential tool in today’s networking environment.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch SSL Secure Sockets Layer (SSL) is a security feature that will provide a secure communication path between a host and client through the use of authentication, digital signatures and encryption.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch SSL Global Settings This window is used to view and configure the SSL feature’s global settings. To view the following window, click Security > SSL > Global Settings, as shown below: Figure 8-13 SSL Global Settings window The fields that can be configured for SSL Global Settings are described below: Parameter Description SSL State Select to enable or disable the SSL feature’s global status here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Web-based Access Control Web-based Access Control (WAC) is a feature designed to authenticate a user when the user is trying to access the Internet via the Switch. The authentication process uses the HTTP or HTTPS protocol. The Switch enters the authenticating stage when users attempt to browse Web pages (e.g., http://www.dlink.com) through a Web browser.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Web Authentication This window is used to view and configure the Web authentication settings. To view the following window, click Security > Web-based Access Control > Web Authentication, as shown below: Figure 8-14 Port Security Global Settings window The fields that can be configured are described below: Parameter Description Web Authentication State Select to enable or disable the Web authentication feature’s global state.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch WAC Port Settings This window is used to view and configure the WAC port settings. To view the following window, click Security > Web-based Access Control > WAC Port Settings, as shown below: Figure 8-15 WAC Port Settings window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch WAC Customize Page This window is used to view and configure the WAC customized login page. To view the following window, click Security > Web-based Access Control > WAC Customize Page, as shown below: Figure 8-16 WAC Customize Page window The fields that can be configured are described below: Parameter Description Page Title Enter a custom page title message here. This message can be up to 128 characters long.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch 9. OAM Cable Diagnostics DDM Cable Diagnostics The cable diagnostics feature is designed primarily for administrators or customer service representatives to verify and test copper cables; it can rapidly determine the quality of the cables and the types of error.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch DDM This folder contains windows that perform Digital Diagnostic Monitoring (DDM) functions on the Switch. There are windows that allow the user to view the digital diagnostic monitoring status of SFP modules inserting to the Switch and to configure alarm settings, warning settings, temperature threshold settings, voltage threshold settings, bias current threshold settings, Tx power threshold settings, and Rx power threshold settings.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch DDM Temperature Threshold Settings This window is used to configure the DDM Temperature Threshold Settings for specific ports on the Switch. To view the following window, click OAM > DDM > DDM Temperature Threshold Settings, as show below: Figure 9-3 DDM Temperature Threshold Settings window The fields that can be configured are described below: Parameter Description Port Select the port used for the configuration here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The fields that can be configured are described below: Parameter Description Port Select the port used for the configuration here. Action Select the action that will be taken here. Options to choose from are Add and Delete. Type Select the type of voltage threshold. Options to choose from are Low Alarm, Low Warning, High Alarm, and High Warning. Value Enter the threshold value. This value must be between 0 and 6.55 Volt.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch DDM TX Power Threshold Settings This window is used to configure the threshold of TX power for specific ports on the Switch. To view the following window, click OAM > DDM > DDM TX Power Threshold Settings, as show below: Figure 9-6 DDM TX Power Threshold Settings window The fields that can be configured are described below: Parameter Description Port Select the port used for the configuration here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The fields that can be configured are described below: Parameter Description Port Select the port used for the configuration here. Action Select the action that will be taken here. Options to choose from are Add and Delete. Type Select the type of TX power threshold. Options to choose from are Low Alarm, Low Warning, High Alarm, and High Warning. Power Unit Select the power unit here. Options to choose from are mW and dBm.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch 10. Monitoring Statistics Mirror Settings Statistics Port Counters This window is used to display port counter statistics. To view the following window, click Monitoring > Statistics > Port Counters, as show below: Figure 10-1 Port Counters window The fields that can be configured are described below: Parameter Description From Port / To Port Select the appropriate port range used for the configuration here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Mirror Settings This window is used to view and configure the mirror feature’s settings. The Switch allows users to copy frames transmitted and received on a port and redirect the copies to another port. Attach a monitoring device to the mirroring port, such as a sniffer or an RMON probe, to view details about the packets passing through the first port. This is useful for network monitoring and troubleshooting purposes.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch 11. Green Power Saving EEE Power Saving This window is used to configure the power saving settings of the Switch. To view the following window, click Green > Power Saving, as shown below: Figure 11-1 Power Saving window The fields that can be configured are described below: Parameter Description Link Detection Power Saving Select this option to enable or disable the link detection state.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch NOTE: The hibernation feature can only be configured when physical stacking is disabled on this switch. After clicking the Power Saving Shutdown Settings tab, the following page will appear. . Figure 11-2 Power Saving Shutdown Settings window The fields that can be configured are described below: Parameter Description From Port / To Port Select the appropriate port range used for the configuration here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch EEE Energy Efficient Ethernet (EEE) is defined in IEEE 802.3az. It is designed to reduce the energy consumption of a link when no packets are being sent. To view the following window, click Green > EEE, as shown below: Figure 11-3 EEE window The fields that can be configured are described below: Parameter Description From Port / To Port Select the appropriate port range used for the configuration here.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch 12. Surveillance Mode Surveillance Overview Port Information IP-Camera Information NVR Information PoE Information PoE Scheduling Management Time Surveillance Settings Surveillance Log Health Diagnostic Toolbar Surveillance Overview In this window, the Surveillance Topology and Device Information are displayed. It appears automatically when you access the Surveillance Mode in the Web UI of the Switch.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The following icons are available in this window and are described below: Parameter Description This displays the total amount of ONVIF IP cameras connected to the Ethernet ports on the Switch. This displays the total amount of D-Link legacy IP cameras (detected by ASV 1.0) connected to the Ethernet ports on the Switch.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch After hovering (with the mouse pointer) over the network device icon, the following additional information will be displayed: Figure 12-3 Additional Device Information After clicking (left-click) the network device icon, the following window will appear.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch After clicking Ping Test button, the following window will appear. Figure 12-5 PD Alive Configuration window (Ping Result) The Ping Result will be displayed. NOTE: A breakdown of the device icons can be found by clicking the Help menu in the toolbar. NOTE: The Switch uses ONVIF traffic to monitor the status of the surveillance device, but some third party devices do not fully comply with the ONVIF standard.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Port Information This window is used to display port information like distance of the network cable, PoE provisioning status, power consumption, Loopback Detection status, group, and how many IP cameras, NVRs, and other devices are connected to the ports.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch This displays the Loopback Detection status on the Ethernet port. Normal - Specifies that there are no loops in the network. Loop - Specifies that there is a loop in the network. Click the Loop link to navigate to the Health Diagnostic window. If an ONVIF IP camera or NVR is connected to the port, the Group Details link will be available. Select the Group Details link to access the Group Details window.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Guide Click the < Back option to return to the previous window. IP-Camera Information This window is used to display IP camera information.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch This displays the IP address and MAC address of the IP camera. This displays the description for the IP icon to modify the camera. Click the description Enter the description for the IP camera here. Click the icon to apply the modified description. NVR Information This window is used to display NVR information.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch This displays the description for the NVR. Click the icon to modify the description Enter the description for the NVR here. Click the icon to apply the modified description. This displays the group ID of the NVR. This displays the number of ONVIF IP cameras managed by this NVR. This displays information about the ONVIF IP camera that is managed by this NVR.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch This displays the number of PoE devices connected to the Switch that is using 15 Watts of power per port. This displays the number of PoE devices connected to the Switch that is using 30 Watts of power per port. This displays the Ethernet port number on the Switch. This displays the PoE state on the port. This can be either PoE ON or PoE OFF. This displays the maximum PoE budget available on this port.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Parameter Description Range Name Enter the name of the time range schedule here. From: Time (Week/HH) Select the starting day and hour in the time range schedule here. Alternatively, click the icon to open a calendar for easy day and hour selection. To: Time (Week/HH) Select the ending day and hour in the time range schedule here. The schedule will end at the end of the selected hour.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Time Clock Settings This window is used to display and configure the time settings on the Switch. To view the following window, click Time > Clock Settings, as shown below: Figure 12-14 Clock Settings window The fields that can be configured are described below: Parameter Description Time (HH:MM:SS) Enter the current time in hours, minutes, and seconds. Enter the current day, month, and year to Date (DD/MM/YYYY) update the system clock.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The fields that can be configured in the SNTP Global Settings section are described below: Parameter Description SNTP State Select to enable or disable the SNTP feature here. Poll Interval Enter the poll interval value here. The range is from 30 to 99999 seconds. By default, this value is 720 seconds. Click the Apply button to accept the changes made.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The fields that can be configured in the Surveillance VLAN Settings section are described below: Parameter Description VLAN ID Enter the ID of the surveillance VLAN here. The range is from 2 to 4094. Click the Apply button to accept the changes made.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch The fields that can be configured in the Uplink Port Settings section are described below: Parameter Description From Port / To Port Select the uplink port range that will be used here. Click the Apply button to accept the changes made. Click the Delete button to remove the specified entry. Surveillance Log This window is used to display the surveillance log.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Health Diagnostic This window is used to display Health Diagnostics information, Discovered Surveillance Devices information, and initiate a cable distance test on all or selected ports on the Switch. For each link-up port, the system will check the link status, PoE status and error counters periodically. This page will refresh every 30s.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Tx/Rx CRC Counter This field displays the TX/RX CRC counter. Discovered Surveillance Devices This field displays the number of ONVIF IP cameras and NVRs discovered on the port. Click the hyperlink (1) to view the group details associated with IP camera or NVR connected to the port. For more information, refer to Group Details on page 360.. Detect Distance Click the Detect button to initiate a cable distance test on the specified port.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch HTTP, as shown below: The fields that can be configured are described below: Parameter Description Source File Enter the source filename and path of the firmware file located on the local PC. This field can be up to 64 characters long. Alternatively click the Browse button to navigate to the location of the firmware file located on the local PC. Click the Upgrade button to initiate the firmware upgrade.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch To view the following window, click Tools > Configuration Restore & Backup > Configuration Restore from HTTP, as shown below: Figure 12-22 Configuration Restore from HTTP window The fields that can be configured are described below: Parameter Description Source File Click the Browse button to navigate to the location of the configuration file located on the local PC.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch To view the following window, click Tools > Reset, as shown below: Figure 12-24 Reset window Select the The Switch will be reset to its factory defaults including IP address, and then will save, reboot option to reset the Switch’s configuration to its factory default settings.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Help Click this option to access the built-in Surveillance Help window. Guide After clicking the Help option, the following window will appear.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Online Help D-Link Support Site Click this option to connect to the D-Link support website. An Internet connection is required. User Guide Click this option to connect to the online user guide for the Switch. An Internet connection is required. Standard Mode Click the Standard Mode button in the toolbar to change the Web UI mode and style from Surveillance Mode to Standard Mode.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Appendix A - System Log Entries The following table lists all possible entries and their corresponding meanings that will appear in the System Log of this switch. Auto Surveillance VLAN Log Description Severity Event description: When a new surveillance device is detected on an interface. Informational Log Message: New surveillance device detected (, MAC: ) Parameters description: interface-id: Interface name.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Event description: When an NVR is added in the surveillance VLAN, the log message Informational will be sent. Log Message: ASV: Add NVR (IP: MAC:< mac-address >) Parameters description: ipaddr: Represent the IP address of the NVR mac-address: Represent the MAC address of the NVR Event description: When an NVR is removed from the surveillance VLAN, the log Informational message will be sent.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Log Message: Optical transceiver alarm threshold exceeded Parameters description: interface-id: port interface ID. component: DDM threshold type. It can be one of the following types: temperature supply voltage bias current TX power RX power high-low: High or low threshold. Event description: when the any of SFP parameters recovers from the warning threshold.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Event description: Record the event when an interface detect loop. Critical Log Message: LBD loop occurred. Parameters description: interface-id: Interface on which loop is detected. Event description: Record the event when an interface loop recovered Critical Log Message: LBD loop recovered. Parameters description: interface-id: Interface on which loop is detected.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Event description: Login through telnet unsuccessfully. Warning Log Message: Login failed through Telnet (Username: , IP: ) Parameters description: username: Represent current login user. ipaddr: Represent client IP address. Informational Event description: Telnet session timed out. Log Message: Telnet session timed out (Username: , IP: ) Parameters description: username: Represent current login user.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Port Security Log Description Severity Event description: Address full on a port. Warning Log Message: MAC address causes port security violation on Parameters description: macaddr: The violation MAC address. interface-id: The interface name. Event description: Address full on system.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Event description: Successful login through Telnet. Informational Log Message: Successful login through Telnet (Username: , IP: ) Parameters description: ipaddr: The IP address of telnet client. username: the user name that used to login telnet server. Warning Event description: Login failed through Telnet.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch vid:VLAN ID Event description: When an interface leaves the voice VLAN and at the same time, Informational no voice device is detected in the aging interval for that interface, the log message will be sent. Log Message: < interface-id > remove from voice VLAN Parameters description: interface-id: Interface name. vid:VLAN ID Web Log Description Severity Event description: Successful login through Web.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Web-Authentication Log Description Severity Event description: When a host has passed the authentication. Log Message: Web-Authentication host login success (Username: , IP: , MAC: , , VID: ) Parameters description: Informational Username: The host username. IP: The host IP address mac-address: The host MAC addresses.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Appendix B - Trap Entries The following table lists all possible trap log entries and their corresponding meanings that will appear in the switch. Authentication Fail Trap Name Description OID authenticationFailure An authenticationFailure trap signifies that the 1.3.6.1.6.3.1.1.5 SNMPv2 entity, acting in an agent role, has received a .5 protocol message that is not properly authenticated.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch LBD Trap Name Description OID isLbdLoopOccurred his trap is sent when an interface loop occurs. 1.3.6.1.4.1.171. Binding objects: 11.155.1000.46. (1) isLbdNotifyInfoIfIndex isLbdLoopRestart 0.1 This trap is sent when an interface loop restarts after 1.3.6.1.4.1.171. the interval time. 11.155.1000.46. Binding objects: 0.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch to the Forwarding state, or from the Forwarding state to the Blocking state. The trap is not sent if a newRoot trap is sent for the same transition. Implementation of this trap is optional PoE Trap Name Description OID pethMainPowerUsageOn This trap indicates PSE Threshold usage indication is 1.3.6.1.2.1.105. Notification on, the usage power is above the threshold. At least 0.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch (3) ifOperStatu Port Security Trap Name Description OID dPortSecMacAddrViolatio When the port security trap is enabled, new MAC 1.3.6.1.4.1.171. n addresses that violate the pre-defined port security 11.155.1000.8.0 1.14.8.0.1 configuration will trigger trap messages to .1 be sent out.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch (5) isnaSessionClientAddress (6) isnaSessionAuthUserName isWebAuthLoggedFail The trap is sent when a host has failed to pass Web- 1.3.6.1.4.1.17.1 Authentication (login failed). 1.155.1000.154. Binding objects: 0.
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch Appendix C - IETF RADIUS Attributes Support Remote Authentication Dial-In User Service (RADIUS) attributes carry specific authentication, authorization, information and configuration details for the request and reply. This appendix lists the RADIUS attributes currently supported by the switch. RADIUS attributes are supported by the IETF standard and Vendor-Specific Attribute (VSA).
