User Manual

ManualsBrandsD-Link ManualsAutomationD-Link DIS-200G-12PS Network RJ45/SFP switch 12 ports PoE

DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch

Summary of content (269 pages)

PAGE 1
DIS-200G Series Industrial Gigabit Ethernet Smart Managed Switch
PAGE 2
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Information in this document is subject to change without notice. Reproduction of this document in any manner, without the written permission of the D-Link Corporation, is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of the D-Link Corporation; Microsoft and Windows are registered trademarks of the Microsoft Corporation.
PAGE 3
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Table of Contents 1. Introduction ............................................................................................................................................................ 1 2. Basic CLI Commands ............................................................................................................................................... 9 3. Access Management Commands .......................................................
PAGE 4
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 42. Traffic Segmentation Commands ....................................................................................................................... 229 43. Virtual LAN (VLAN) Commands ........................................................................................................................... 231 44. Voice VLAN Commands..............................................................................................................
PAGE 5
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 1. Introduction This manual’s command descriptions are based on the software release 1.10 The commands listed here are the subset of commands that are supported by the DIS-200G Series Smart Switch. Audience This CLI Reference Guide is intended for network administrators and other IT networking professionals responsible for managing the switch by using the Command Line Interface (CLI).
PAGE 6
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide NOTICE: A notice indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A caution indicates a potential for property damage, personal injury, or death. Command Descriptions The information pertaining to each command in this reference guide is presented using a number of template fields.
PAGE 7
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide EXEC Mode.  Users with a basic user level will log into the Switch in the User EXEC Mode.  Users with administrator level accounts will log into the Switch in the Privileged EXEC Mode. Therefore, the User EXEC Mode can operate at a basic user level and the Privileged EXEC Mode can operate at the administrator levels. The user can only enter the Global Configuration Mode from the Privileged EXEC Mode.
PAGE 8
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Global Configuration Mode The primary purpose of the global configuration mode is to apply global settings on the entire switch. Global configuration mode can be accessed at administrator level user accounts. In addition to applying glabal settings on the entire switch, the user can also access other sub-configuration modes.
PAGE 9
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide of user and a password of pass1234. Save the running configuration to the start-up configuration. This means to save the changes made so that when the Switch is rebooted, the configuration will not be lost. The following example shows how to save the running configuration to the start-up configuration. Switch# copy running-config startup-config Building configuration...
PAGE 10
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Error Messages When the users issue a command that the Switch does not recognize, error messages will be generated to assist users with basic information about the mistake that was made. A list of possible error messages are found in the table below. Error Message Meaning Ambiguous word detected at '^' marker Not enough keywords were entered for the Switch to recognize the command.
PAGE 11
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Left Arrow Moves the cursor to the left. Right Arrow Moves the cursor to the right. Return Scrolls down to display the next line or used to issue a command. Space Scrolls down to display the next page. Display Result Output Modifiers Results displayed by show commands can be filtered using the following parameters:  begin FILTER-STRING - This parameter is used to start the display with the first line that matches the filter string.
PAGE 12
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch# show running-config | include vlan vlan 1 interface vlan 1 Switch# The example below shows how to use the exclude FILTER-STRING parameter in a show command.
PAGE 13
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 2. Basic CLI Commands 2-1 help This command is used to display a brief description of the help system. Use the help command in any command modes help Parameters None. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1.
PAGE 14
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide the character '?' in a string argument, press ctrl+v immediately followed by the character '?'. Switch# The following example shows how to use the word help to display all the Privileged EXEC Mode commands that begin with the letters “re”. The letters entered before the question mark (?) are reprinted on the next command line to allow the user to continue entering the command. Switch# re? reboot Reboot system.
PAGE 15
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 2-3 logout This command is used to close an active terminal session by logging off the Switch. logout Parameters None. Default None. Command Mode User EXEC Mode. Privilege EXEC Mode. Command Default Level Level:1. Usage Guideline Use this command to close an active terminal session by logging out of the device.
PAGE 16
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch(config-if)#end Switch# 2-5 exit This command is used to end the configuration mode and go back to the last mode. If the current mode is the User EXEC Mode or the Privilege EXEC Mode, executing the exit command logs you out of the current session. exit Parameters None. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1.
PAGE 17
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Commands entered are recorded by the system. A recorded command can be recalled by pressing CTRL+P or the Up Arrow key which will recall previous commands in sequence. The history buffer size is fixed at 32 commands. The function key instructions, below, displays how to navigate the command in the history buffer.  CTRL+P or the Up Arrow key - Recalls commands in the history buffer, beginning with the most recent command.
PAGE 18
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 2-8 show version This command is used to display the Switch’s software version information. show version Parameters None. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command displays version information about the Switch. Example This example shows how to displays version information about the Switch.
PAGE 19
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 3. Access Management Commands 3-1 ip http secure-server This command is used to enable the HTTPS server. Use the no form of this command to disable the HTTPS server function. ip http secure-server no ip http secure-server Parameters None. Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15 Usage Guideline This command enables the HTTPS server function.
PAGE 20
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline Use this command to display information about the terminal configuration parameters for the current terminal line. Example This example shows how to display information about the terminal configuration parameter settings for the current terminal line.
PAGE 21
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 3-4 show users This command is used to display information about the active lines on the Switch. show users Parameters None. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command displays information about the active lines on the Switch. Example This example shows how to display all session information.
PAGE 22
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Default By default, this value is 24. Command Mode Use the EXEC Mode or Privilege EXEC Mode for the terminal length command. Command Default Level Level: 1 (for the terminal length command). Usage Guideline When the terminal length is 0, the display will not stop until it reaches the end of the display. If the terminal length is specified to a value other than 0, for example 50, then the display will stop after every 50 lines.
PAGE 23
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide command changes the terminal width value which applies only to the current session. When changing the value in a session, the value applies only to that session. When the no form of this command is used, the number of lines in the terminal display screen is reset to the default, which is 80 characters.
PAGE 24
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide syntax remains plain text 7 Specifies the encrypted password based on SHA-1. The password length is fixed at 35 bytes. It is case-sensitive. The password is encrypted. If the password syntax is not specified, the syntax is plain text. 15 Specifies the encrypted password based on MD5. The password length is fixed at 31 bytes. It is case-sensitive. The password is encrypted. If the password syntax is not specified, the syntax is plain text.
PAGE 25
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 3-8 service password encryption This command is used to enable the encryption of the password before stored in the configuration file. The no command will disable the encryption. service password-encryption [7 | 15] no service password-encryption Parameters 7 Specifies the algorithm of password encryption as SHA-1. 15 Specifies the algorithm of password encryption as MD5. Default By default, this option is disabled.
PAGE 26
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 4. Asymmetric VLAN Commands 4-1 asymmetric-vlan his command is used to enable the asymmetric VLAN function. Use the no form of this command todisable the asymmetric VLAN function. asymmetric-vlan no asymmetric-vlan Parameters None. Default By default, this feature is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15 Usage Guideline Use this command to enable or disable the asymmetric VLAN function.
PAGE 27
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 5. Basic IPv4 Commands 5-1 ip address This command is used to IPv4 address for an interface, or acquire an IP address on an interface from the DHCP. Use the no form of this command to remove the configuration of an IP address or disable DHCP on the interface. ip address {IP-ADDRESS SUBNET-MASK | dhcp} no ip address Parameters IP-ADDRESS Specifies the IP address. SUBNET-MASK Specifies the subnet mask for the associated IP address.
PAGE 28
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide NETWORK-PREFIX Specifies the network address. NETWORK-MASK Specifies the network mask IP-ADDRESS Specifies to an IP address. Default none. Command Mode Global Configuration Mode. Command Default Level Level: 15 Usage Guideline Use this command to configure static route that destination is default gateway. The net-address and net-mask only allow to configure with 0.0.0.0.
PAGE 29
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Interface Address Method Status ---------------- -------------------- -------- -----VLAN 1 10.90.90.91/24 Manual UP Switch# 5-4 show ip route This command is used to display ip address of default gateway. show ip route Parameters None. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the ip address of default gateway.
PAGE 30
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 6. Basic IPv6 Commands 6-1 ipv6 address This command is used to manually configure an IPv6 addresses on the management VLAN . Use the no form of this command to disable IPv6 address for management VLAN. ipv6 address IPV6-ADDRESS no ipv6 address Parameters IPV6-ADDRESS Specifies the IPv6 address and the length of prefix for the management VLAN. Default None. Command Mode Interface Configuration Mode. Command Default Level Level: 15.
PAGE 31
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide show ipv6 interface [INTERFACE-ID] brief Parameters INTERFACE-ID Specifies the interface for display. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display IPv6 interface related configurations. Example This example shows how to display IPv6 interface information.
PAGE 32
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 7. Cable Diagnostics Commands 7-1 test cable-diagnostics This command is used to start the cable diagnostics to test the status and length of copper cables. test cable-diagnostics interface INTERFACE-ID Parameters interface INTERFACE-ID Specifies the interface ID. The acceptable interface will be a physical port. Default None. Command Mode EXEC Mode. Command Default Level Level: 15.
PAGE 33
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide None. Command Mode EXEC Mode. Command Default Level Level: 1. Usage Guideline This command is used to display the test results for the cable diagnostics. Example This example shows how to display the test results for the cable diagnostics.
PAGE 34
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Usage Guideline This command is used to clear the test results for the cable diagnostics. Example This example shows how to clear the test results for the cable diagnostics.
PAGE 35
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 8. Digital Diagnostics Monitoring (DDM) Commands 8-1 show interfaces transceiver This command is used to display the current SFP module operating parameters. show interfaces [INTERFACE-ID [,|-] transceiver [detail] Parameters INTERFACE-ID [,|-] (Optional) Specifies multiple interfaces for transceiver monitoring status display. If no interface ID is specified, transceiver monitoring statuses on all valid interfaces are displayed. Default None.
PAGE 36
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide ++ : high alarm, + : high warning, - : low warning, -- : low alarm mA: milliamperes, mW: milliwatts A: The threshold is administratively configured. eth1/0/11 Transceiver Monitoring is enabled Transceiver Monitoring shutdown action：Alarm Temperature(C) Current High-Alarm High-Warning Low-Warning Low-Alarm 30.090 75.000(A) 70.000 0.000 -5.000 3.630 3.465 3.135 2.970 Voltage (v) 3.353 Bias Current(mA) 16.794(++) 10.500 9.000 2.
PAGE 37
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch(config)# snmp-server enable traps transceiver-monitoring warning Switch(config)# 8-3 transceiver-monitoring action shutdown This command is used to shut down a port from an alarm or a warning of an abnormal status. Use the no form of the command to disable the shutdown action.
PAGE 38
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 8-4 transceiver-monitoring bias-current This command is used to configure the thresholds of the bias current for a specified port. Use the no form of the command to remove the configuration. transceiver-monitoring bias-current INTERFACE-ID {high | low} {alarm | warning} VALUE no transceiver-monitoring bias-current INTERFACE-ID {high | low} {alarm | warning} Parameters INTERFACE-ID Specifies the interface to modify.
PAGE 39
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 8-5 transceiver-monitoring enable This command is used to enable the optical transceiver monitoring function for an SFP port. Use the no form of the command to disable optical transceiver monitoring. transceiver-monitoring enable no transceiver-monitoring enable Parameters None. Default By default, this option is disabled. Command Mode Interface Configuration Mode. Command Default Level Level: 15.
PAGE 40
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Parameters INTERFACE ID Specifies the interface to modify. high Specifies that when the operating parameter rises above the highest threshold, it indicates an abnormal status. low Specifies that when the operating parameter falls below the low threshold this value, it indicates an abnormal status. alarm Specifies to configure the high and low threshold value condition.
PAGE 41
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide INTERFACE ID Specifies the interface to modify. high Specifies that when the operating parameter rises above this high threshold value, it indicates an abnormal status. low Specifies that when the operating parameter falls below this low threshold value, it indicates an abnormal status. alarm Specifies to configure the high and low threshold value condition. warning Specifies to configure the high and low warning threshold conditions.
PAGE 42
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide high Specifies the interface to modify. low Specifies that when the operating parameter rises above this high threshold value, it indicates an abnormal status. alarm Specifies that when the operating parameter falls below this low threshold value, it indicates an abnormal status. warning Specifies to configure the high and low warning threshold conditions. mwatt VALUE Specifies the power threshold value in milliwatts.
PAGE 43
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide low Specifies that when the operating parameter falls below this low threshold value, it indicates an abnormal status. alarm Specifies to configure the high and low threshold value condition. warning Specifies to configure the high and low warning threshold conditions. VALUE Specifies the threshold value. This value must be between 0 and 6.55 Volt. Default None. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 44
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 9. D-Link Discovery Protocol (DDP) ClientCommands 9-1 ddp This command is used to enable DDP client function globally. Use the no form of this command to disable DDP client. ddp no ddp Parameters None. Default By default, this option is enabled. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command to enable or disable DDP client function globally.
PAGE 45
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Parameters 30 Specifies the report interval to 30 seconds. 60 Specifies the report interval to 60 seconds. 90 Specifies the report interval to 90 seconds. 120 Specifies the report interval to 120 seconds. Never Specifies to stop sending report message. Default By default, this option is 30 seconds. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 46
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This example shows how to display DDP global information.
PAGE 47
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 10. DoS Prevention Commands 10-1 dos-prevention This command is used to enable and configure the DoS prevention mechanism. Use the no form of this command to reset DoS prevention to the default setting. dos-prevention DOS-ATTACK-TYPE no dos-prevention DOS-ATTACK-TYPE Parameters DOS-ATTACK-TYPE Specifies the string that identifies the DoS type to be configured. Default By default all supported DoS types are disabled.
PAGE 48
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide  All: All of above types. Example This example shows how to enable the DoS prevention mechanism for land attack. Switch# configure terminal Switch(config)# dos-prevention land Switch(config)# This example shows how to enable the DoS prevention mechanism on all supported types. Switch# configure terminal Switch(config)# dos-prevention all Switch(config)# This example shows how to disable the DoS prevention mechanism for all supported types.
PAGE 49
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide DoS Type State -------------------------- -------Land Attack Enabled Blat Attack Enabled TCP Null Enabled TCP Xmas Enabled TCP SYN-FIN Enabled TCP SYN SrcPort Less 1024 Enabled Ping of Death Attack Enabled Switch# This example shows how to display the specified type configuration information of the DoS prevention.
PAGE 50
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 11. Ethernet Ring Protection Switching (ERPS) Commands 11-1 description This command is used to configure the description for Ethernet Ring Protection (ERP) instances. description DESCRIPTION Parameters None. Default None. Command Mode ERP Instance Configuration Mode. Command Default Level Level: 15. Usage Guideline This command is used to configure the description for the ERP instances.
PAGE 51
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide None. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline This command is used to create, modify or delete an ITU-T G.8032 ERP physical ring and enter the ERP configuration mode. Example This example shows how to create an ERP ring named “campus”.
PAGE 52
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 11-4 r-aps channel-vlan This command is used to specify the APS channel VLAN for an ERP instance. Use the no form of this command to delete the configuration. r-aps channel-vlan VLAN-ID no r-aps channel-vlan Parameters VLAN-ID Specifies the VLAN ID. The valid values are from 1 to 4094. Default None. Command Mode ERP Instance Configuration Mode. Command Default Level Level: 15.
PAGE 53
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide VLAN-ID Specified the VLAN IDs protected by the ERP mechanism. The range is 1 to 4094. , (Optional) Specifies a series of VLANs, or separate a range of VLANs from a previous range. No spaces are required before and after the comma. - (Optional) Specifies a range of VLANs. No spaces are required before and after the hyphen. Default None. Command Mode ERP Instance Configuration Mode. Command Default Level Level: 15.
PAGE 54
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Level: 15. Usage Guideline This command is used to create or remove an ERP instance and enter ERP instance configuration mode. Example This example shows how to configure service protected VLAN as 100-200 for ERP instance 1. Switch# configure terminal Switch(config)# ethernet ring g8032 ring2 Switch(config-erp)# instance 1 Switch(config-erp-instance)# 11-7 level This command is used to configure ring MEL value of an ERP instance.
PAGE 55
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 11-8 profile This command is used to associate an ERP instance with a G.8032 profile. Use the no form of this command to remove the association. profile PROFILE-NAME no profile PROFILE-NAME Parameters PROFILE-NAME Specifies the profile name to be associated with the ERP instance. Default None. Command Mode ERP Instance Configuration Mode. Command Default Level Level: 15.
PAGE 56
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Mode ERP Configuration Mode. Command Default Level Level: 15. Usage Guideline This command is used to specify or remove the first ring port of a physical ring. Example This example shows how to configure the interface “eth1/0/1” as the first ring port of the G.8032 ring “ring1”.
PAGE 57
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch(config-erp)# instance 1 Switch(config-erp-instance)# port1 none Switch(config-erp-instance)# 11-11 revertive This command is used to revert back to the working transport entity, for example, when the RPL was blocked. Use the no form of this command to continue using the RPL, if it has not failed and if the ‘switch link defect’ condition was cleared. revertive no revertive Parameters None. Default By default, this option is revertive.
PAGE 58
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide no rpl Parameters port0 Specified port0 as the RPL port. port1 Specified port1 as the RPL port. owner (Optional) Specifies the ring node as the RPL owner node. Default None. Command Mode ERP Instance Configuration Mode. Command Default Level Level: 15. Usage Guideline This command is used to configure the node as the RPL owner or RPL neighbor, or assign the port as the RPL port.
PAGE 59
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline This command is used to display information of the ERP instances. Example This example shows how to display the detailed information of the ERP instances.
PAGE 60
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide MEL Ring MEL value of ERP instance. R-APS Channel APS channel of ERP instance. Protected VLANs Service protected VLANs of ERP instance. Profile The profile associated with the ERP instance. Guard timer Time value for guard timer of the profile. Hold-Off timer Time value for hold-off timer of the profile.
PAGE 61
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 11-14 Port-State Current ring ports state. (- / Forwarding / Blocked) status Specifies to display the status of the ERP instances. brief Specifies to display the brief information of the ERP instances. activate This command is used to activate the specified ERP instance. Use the no form of this command to deactivate the specified ERP instance. Activate no activate Parameters None. Default By default, this option is no activate.
PAGE 62
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide no timer {guard | hold-off | wtr} Parameters guard MILLI-SECONDS (Optional) Specifies the guard timer in milliseconds. The value is range from 10 to 2000. hold-off SECONDS (Optional) Specifies the hold-off timer in seconds. The value is range from 0 to 10. wtr MINUTES (Optional) Specifies the WTR timer in minutes. The value is range from 1 to 12. status Specifies to display the status of the ERP instances.
PAGE 63
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 12. File System Commands 12-1 delete This command is used to delete a file. delete FILE-URL Parameters FILE-URL Specifies the name of the file in flash. Sytax: . Default None. Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline The firmware image or the default configuration file cannot be deleted. Example This example shows how to delete the file named “office.
PAGE 64
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Usage Guideline Use to display all files information in the Flash. Example This example shows how to display all files information in the Flash. Switch# dir Directory of flash: 1 -r- 308 Jan 01 1970 00:00:00 default-config 2 -rw 776 Mar 13 2017 13:28:51 startup-config 3 -rw 776 Mar 15 2017 11:31:09 office.cfg 4 -r- 3898396 Mar 14 2017 09:57:09 R1.10.B013.dat 5 -r- 3893579 Mar 15 2017 11:28:57 R1.10.B014.
PAGE 65
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 13. Filter Database (FDB) Commands 13-1 clear mac-address-table This command is used to delete a specific dynamic MAC address, all dynamic MAC addresses on a particular interface, all dynamic MAC addresses on a particular VLAN, or all dynamic MAC addresses from the MAC address table. clear mac-address-table dynamic {all | interface INTERFACE-ID} Parameters all Specifies to clear all dynamic MAC addresses.
PAGE 66
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Default By default, this value is 300 seconds. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline Setting the aging time to 0 will disable the MAC address table aging out function. Example This example shows how to set the aging time value to 200 seconds.
PAGE 67
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch# configure terminal Switch(config)# mac-address-table learning interface Ethernet 1/0/1 Switch(config)# 13-4 mac-address-table static This command is used to add a static address to the MAC address table. Use the no form of this command to remove a static MAC address entry from the table.
PAGE 68
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Ethernet 1/0/1 Switch(config)# This example shows how to add the static address C2:F3:22:0A:22:33 to the MAC address table. It also specifies that when any packet received on VLAN 4 that has a destination MAC address of C2:F3:22:0A:22:33 will be forwarded to port-channel 2.
PAGE 69
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch(config)# 13-6 show mac-address-table This command is used to display a specific MAC address entry or the MAC address entries for a specific interface or VLAN. show mac-address-table [dynamic | static] [address MAC-ADDR | interface [INTERFACE-ID | vlan VLAN-ID] Parameters dynamic (Optional) Specifies to display dynamic MAC address table entries only. static (Optional) Specifies to display static MAC address table entries only.
PAGE 70
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This example shows how to display all the static MAC address table entries.
PAGE 71
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This command is used to display the MAC address table’s aging time. Example This example shows how to display the MAC address table’s aging time. Switch# show mac-address-table aging-time Aging Time is 300 seconds Switch# 13-8 show mac-address-table learning This command is used to display the MAC-address learning state.
PAGE 72
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch# 13-9 show multicast filtering-mode This command is used to enable and configure the DoS prevention mechanism. Use the no form of this command to reset DoS prevention to the default setting. show multicast filtering-mode Parameters None. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline None.
PAGE 73
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 14. GARP VLAN Registration Protocol (GVRP) Commands 14-1 gvrp global This command is used to enable the GVRP function globally. Use the no form of this command to disable the GVRP function globally. gvrp global no gvrp global Parameters None. Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 74
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 15. Usage Guideline Administrators can enable the global GVRP state and individual port’s GVRP state to start GVRP on the port. Example This example shows how to enable the GVRP protocol global state.
PAGE 75
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Level: 15. Usage Guideline The command is available for both physical ports and port-channel interface configuration. Administrators can use the gvrp advertise command to enable the specified VLANs’ GVRP advertise function on the specified interface. The command only takes effect when GVRP is enabled. The command only takes effect for hybrid mode and trunk mode.
PAGE 76
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 14-5 gvrp forbidden This command is used to specify a port as being a forbidden member of the specified VLAN. Use the no form of this command to remove the port as a forbidden member of all VLANs. gvrp forbidden {all | [add | remove] VLAN-ID [, | -]} no gvrp forbidden Parameters all Specifies that all VLANs, except VLAN 1, are forbidden on the interface. add (Optional) Specifies a VLAN or a list VLANs to be added to forbidden the VLAN list.
PAGE 77
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 14-6 gvrp timer This command is used to configure the GVRP timer value on a port. Use the no form of this command to revert the timer to the default setting. gvrp timer [join JOIN-TIMER-VALUE] [leave LEAVE-TIMER-VALUE] [leave-all LEAVE-ALL-TIMERVALUE] no gvrp timer [join] [leave] [leave-all] Parameters join (Optional) Specifies to set the timer for joining a group. The unit is in a hundredth of a second.
PAGE 78
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 14-7 show gvrp configuration This command is used to display the GVRP settings. show gvrp configuration [interface [INTERFACE-ID [,|-]]] Parameters configuration Specifies to display the GVRP configuration. If the interface is not specified, the GVRP global configuration is displayed. interface Specifies to display the GVRP interface configuration. If the interface ID is not specified, all interfaces are displayed.
PAGE 79
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Advertise VLAN : 1-3 Forbidden VLAN : 5-8 Switch# 75
PAGE 80
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 15. IGMP Snooping Commands 15-1 ip igmp snooping This command is used to enable the IGMP snooping function on the Switch. Use the no form of this command to disable the IGMP snooping function. ip igmp snooping no ip igmp snooping Parameters None. Default IGMP snooping is disabled on all VLAN. The IGMP snooping global state is disabled by default. Command Mode VLAN Configuration Mode. Global Configuration Mode. Command Default Level Level: 15.
PAGE 81
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 15-2 ip igmp snooping querier This command is used to enable the capability of the entity as an IGMP querier. Use the no form of this command to disable the querier function. ip igmp snooping querier no ip igmp snooping querier Parameters None. Default By default, this option is disabled. Command Mode VLAN Configuration Mode. Command Default Level Level: 15.
PAGE 82
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Default Level Level: 15. Usage Guideline The ip igmp snooping fast-leave command allows IGMP membership to be immediately removed from a port when receiving the leave message without using the group specific or group-source specific query mechanism.
PAGE 83
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Example This example shows how to statically add a group for IGMP snooping. Switch# configure terminal Switch(config)# vlan 1 Switch(config-vlan)# ip igmp snooping static-group 225.1.2.3 interface Ethernet 1/0/1 Switch(config-vlan)# 15-5 show ip igmp snooping This command is used to display IGMP snooping information on the Switch. show ip igmp snooping [vlan VLAN-ID] Parameters vlan VLAN-ID (Optional) Specifies the VLAN to be displayed.
PAGE 84
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch# 15-6 show ip igmp snooping groups This command is used to display IGMP snooping group information learned on the Switch. show ip igmp snooping groups [vlan VLAN-ID | IP-ADDRESS] Parameters vlan VLAN-ID (Optional) Specifies the VLAN interface to be displayed. If no VLAN is specified, IGMP snooping group information of all VLANs will be displayed, at which IGMP Snooping is enabled.
PAGE 85
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This command is used to display IGMP snooping statistics group information on the Switch. show ip igmp snooping static-group [GROUP-ADDRESS | vlan VLAN-ID] Parameters GROUP-ADDRESS (Optional) Specifies the group IP address to be displayed. vlan VLAN-ID (Optional) Specifies the VLAN ID to be displayed. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1.
PAGE 86
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 16. Interface Commands 16-1 clear counters This command is used to clear counters for a physical port interface. clear counters {all | interface INTERFACE-ID [,|-]} Parameters all Specifies to clear counters for all interfaces. INTERFACE-ID Specifies the interface ID to clear the counter. Default None. Command Mode Privileged EXEC Mode. Command Default Level Level: 1.
PAGE 87
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Interface Configuration Mode. Command Default Level Level: 15. Usage Guideline The specified description corresponds to the MIB object “ifAlias” defined in the RFC 2233. Notice that space is not alllowed in the description. Example This example shows how to add the description “Port10” to interface Ethernet 1/0/10.
PAGE 88
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide physical port interface has the channel-group command configured for it. Use the no interface portchannel command to remove a port-channel. Example This example shows how to enter the interface configuration mode for the interface Ethernet1/0/1. Switch# configure terminal Switch(config)# interface Ethernet 1/0/1 Switch(config-if)# This example shows how to enter the interface configuration mode for VLAN 1.
PAGE 89
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This command enters the interface configuration mode for the specified range of interfaces. Commands configured in the interface range mode, applies to interfaces in the range.
PAGE 90
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide rxHCPkt64Octets : 0 rxHCPkt65to127Octets : 0 rxHCPkt128to255Octets : 0 rxHCPkt256to511Octets : 0 rxHCPkt512to1023Octets : 0 rxHCPkt1024to1518Octets : 0 rxHCPkt1519to9216Octets : 0 txHCPkt64Octets : 0 txHCPkt65to127Octets : 0 txHCPkt128to255Octets : 0 txHCPkt256to511Octets : 138 txHCPkt512to1023Octets : 0 txHCPkt1024to1518Octets : 0 txHCPkt1519to9126Octets : 0 rxCRCAlignErrors : 0 rxUndersizedPkts : 0 rxOversizedPkts
PAGE 91
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Usage Guideline If no interface is specified, all existing physical ports will be displayed. Example This example shows how to display the interface information for interface VLAN 1. Switch# show interfaces vlan 1 VLAN1 LINK: 00-01-c1-13-14-08 Mtu:1500 IPv4: 192.168.1.2/24 192.168.1.
PAGE 92
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command displays the Switch’s port connection status.
PAGE 93
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Default Level Level: 15. Usage Guideline The physical port is valid for this configuration. This command is also configurable for port channel member ports. The command will cause the port to enter the disabled state. Under the disabled state, the port will not be able to receive or transmit any packets. Using the no shutdown command will put the port back into the enabled state.
PAGE 94
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 17. IP Utility Commands 17-1 ping This command is used to diagnose basic network connectivity. ping {[ip] IP-ADDRESS } [count TIMES] [timeout SECONDS] Parameters ip (Optional) Specifies the destination IPv4 address. IP-ADDRESS Specifies the IPv4 address of the destination host. count TIMES (Optional) Specifies to stop after sending the specified number of echo request packets.
PAGE 95
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 18. Jumbo Frame Commands 18-1 max-rcv-frame-size This command is used to configure the maximum Ethernet frame size allowed. Use the no form of this command to revert to the default setting. max-rcv-frame-size BYTES no max-rcv-frame-size Parameters BYTES Specifies the maximum Ethernet frame size allowed. Default By default, this value is 1518 bytes. Command Mode Interface Configuration Mode. Command Default Level Level: 15.
PAGE 96
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 19. Link Aggregation Control Protocol (LACP)Commands 19-1 channel-group This command is used to assign an interface to a channel group. Use the no form of this command to remove an interface from a channel-group. channel-group CHANNEL-NO mode {on | active | passive} no channel-group Parameters CHANNEL-NO Specifies the channel group ID. The valid range is 1 to 6. on Specifies that the interface is a static member of the channel-group.
PAGE 97
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 19-2 show channel-group This command is used to display the channel group information. show channel-group [channel [CHANNEL-NO] {detail | neighbor} | load-balance | sys-id] Parameters CHANNEL-NO (Optional) Specifies the channel group ID. channel (Optional) Specifies to display information for the specified portchannels. detail (Optional) Specifies to display detailed channel group information.
PAGE 98
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Member Ports: 2, Maxports = 8, Protocol: LACP Port Flags LACP Port Port State Priority Number ------------------------------------------------eth1/0/10 SA bndl 32768 10 eth1/0/11 SA bndl 32768 11 Channel Group 2 Member Ports: 2, Maxports = 8, Protocol: Static Port Flags LACP Port Port State Priority Number -------------------------------------------------eth1/0/8 N/A bndl N/A N/A eth1/0/9 N/A down N/A N/A Switch#
PAGE 99
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch# This example shows how to display the summary information for all port-channels.
PAGE 100
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 20. Link Layer Discovery Protocol (LLDP)Commands 20-1 lldp run This command is used to enable the Link Layer Discovery Protocol (LLDP) globally. Use the no form of this command to revert to the default setting. lldp run no lldp run Parameters None. Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 101
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Default The LLDP states is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline Use the snmp-server enable traps lldp command to enable the sending of LLDP notifications. Example This example shows how to enable the LLDP trap.
PAGE 102
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 20-4 show lldp neighbor interface This command is used to display each physical interface’s information currently learned from the neighbor. show lldp neighbors interface INTERFACE-ID [, | -] brief Parameters INTERFACE-ID Specifies the interface ID. , (Optional) Specifies a series of interfaces, or separate a range of interfaces from a previous range. No spaces before and after the comma. - (Optional) Specifies a range of interfaces.
PAGE 103
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Port Description : RMON Port 1 on Unit 4 Port ID : eth1/0/2 --------------------------------------------------------------------Remote Entities Count : 3 Entity 1 Chassis ID Subtype : MAC Address Chassis ID : 00-01-02-03-04-03 Port ID Subtype : Local Port ID : eth1/0/1 Port Description : RMON Port 2 on Unit 1 Entity 2 Chassis ID Subtype : MAC Address Chassis ID : 00-01-02-03-04-04 Port ID Subtype : Local Port ID : eth1/0/2 Port Description
PAGE 104
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 21. Loopback Detection (LBD) Commands 21-1 loopback-detection (Global) This command is used to enable the loopback detection function globally. Use the no form of this command to disable the function globally. loopback-detection no loopback-detection Parameters None. Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 105
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Parameters None. Default By default, this option is disabled. Command Mode Interface Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command to enable the loopback detection function on an interface. This command is available for port and port-channel interface configuration. Example This example shows how to enable the loopback detection function on interface Ethernet 1/0/1.
PAGE 106
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This example shows how to configure the time interval to 20 seconds. Switch# configure terminal Switch(config)# loopback-detection interval 20 Switch(config)# 21-4 loopback-detection recover-time This command is used to configure the recover timer interval. Use the no form of this command to revert to the default setting. loopback-detection recover-time SECONDS no loopback-detection recover-time Parameters recover-time SECONDS 0 or 60-1000000.
PAGE 107
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide , (Optional) Specifies a series of interfaces, or separate a range of interfaces from a previous range. No spaces are allowed before and after the comma. - (Optional) Specifies a range of interfaces. No spaces are allowed before and after the hyphen. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the loopback detection setting and status.
PAGE 108
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This example shows how to displays the loopback detection status for port-channel 2. Switch# show loopback-detection interface port-channel2 Interface State Result Time Left (sec) -------------- -------- ----------------- --------------- Port-channel2 Disabled Normal - Switch# Display Parameters Interface Indicates the port that has loopback detection enabled. State Indicates the loopback detection state in each port.
PAGE 109
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch(config)# snmp-server enable traps loopback-detection. Switch(config)# 22. Mirror Commands 22-1 monitor session destination interface This command is used to configure the destination interface for a port monitor session, allowing packets on source ports to be monitored via a destination port. Use the no form of this command to delete a port monitor session or remove the destination interface of the session.
PAGE 110
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide monitor session SESSION-NUMBER source interface INTERFACE-ID [, | -] [both | rx | tx] no monitor session SESSION-NUMBER source interface INTERFACE-ID [, | -] no monitor session SESSION-NUMBER Parameters session SESSION-NUMBER Specifies the session number for the port monitor session. The valid range is 1. interface INTERFACE-ID Specifies the source interface for a port monitor session.
PAGE 111
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide show monitor session [SESSION-NUMBER] Parameters session SESSION-NUMBER (Optional) Specifies the session number which you want to display. The valid range is 1. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline If this command is used without specifying a session number, all monitor sessions are displayed.
PAGE 112
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 23. MLD Snooping Commands 23-1 ipv6 mld snooping This command is used to enable or disable MLD snooping. ipv6 mld snooping no ipv6 mld snooping Parameters None. Default MLD snooping is disabled on all VLAN interfaces. The MLD snooping global state is disabled by default. Command Mode VLAN Configuration Mode. Global Configuration Mode. Command Default Level Level: 15.
PAGE 113
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 23-2 ipv6 mld snooping querier This command is used to enable the MLD snooping querier on the Switch. Use the no form of this command to disable the MLD snooping querier function. ipv6 mld snooping querier no ipv6 mld snooping querier Parameters None. Default By default, this option is disabled. Command Mode VLAN Configuration Mode. Command Default Level Level: 15.
PAGE 114
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Usage Guideline The ipv6 mld snooping fast-leave command allows MLD membership to be immediately removed from a port when receiving the leave message without using the group specific or group-source specific query mechanism. Example This example shows how to enable MLD snooping fast-leave on VLAN 1.
PAGE 115
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 23-5 show ipv6 mld snooping This command is used to display MLD snooping information on the Switch. show ipv6 mld snooping [vlan VLAN-ID] Parameters vlan VLAN-ID (Optional) Specifies the VLAN to be displayed. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display MLD snooping configurations. .
PAGE 116
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide vlan VLAN-ID (Optional) Specifies the VLAN interface. If no interface is specified, MLD group information about all interfaces will be displayed. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display MLD group information by command. Example This example shows how to display MLD snooping group information.
PAGE 117
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command displays the MLD snooping static group information. Example This example shows how to display MLD snooping static group information .
PAGE 118
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 24. Multiple Spanning Tree Protocol (MSTP) Commands 24-1 instance This command is used to map a VLAN or a set of VLANs to an MST instance. Use the no instance without VLANs specified to remove instances. Use the no instance with VLAN specified to return the VLANs to the default instance (CIST).
PAGE 119
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 24-2 name This command is used to configure the name of an MST region. Use the no form of this command to revert to the default setting. name NAME no name NAME Parameters NAME Specifies the name given for a specified MST region. The name string has a maximum length of 32 characters and the type is a general string which allows spaces. Default The default name is the Switch’s MAC address. Command Mode MST Configuration Mode.
PAGE 120
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide By default, this value is 0. Command Mode MST Configuration Mode. Command Default Level Level: 15. Usage Guideline Two Ethernet switches that have the same configuration but different revision numbers are considered to be part of two different regions. Example This example shows how to configure the revision level of the MSTP configuration to 2.
PAGE 121
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This example shows how to display MSTP summary information.
PAGE 122
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide None. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline This command is used to enter the MST Configuration Mode. Example This example shows how to enter the MST Configuration Mode. Switch# configure terminal Switch(config)# spanning-tree mst configuration Switch(config-mst)# 24-6 spanning-tree mst priority This command is used to configure the bridge priority value for the selected MSTP instance.
PAGE 123
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 25. Power over Ethernet (PoE) Commands 25-1 poe pd priority This command is used to configure the priority for provisioning power to the port. Use the no form of this command to revert to the default setting. poe pd priority {critical | high | low} no poe pd priority Parameters critical Specifies the PD connected to the port gains the highest priority. high Specifies the PD connected to the port gains the second high priority.
PAGE 124
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide no poe power-inline [auto time-range] Parameters auto Specifies to enable the auto-detection of PDs and provision power to the PD. time-range PROFILE-NAME (Optional) Specifies the name of the time-range profile to delineate the activation period. never Specifies to disable supplying power to PD connected to the port. Default By default, this option is set as auto. Command Mode Interface Configuration Mode. Command Default Level Level: 15.
PAGE 125
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide poe usage-threshold This command is used to configure the utilization threshold to record a log. Use the no form of this command to restore to the default setting. poe usage-threshold PERCENTAGE no poe usage-threshold Parameters PERCENTAGE Specifies the usage threshold to generate a log. The valid range is from 1 to 99. The unit is percentage. Default By default, this value is 99. Command Mode Global Configuration Mode.
PAGE 126
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Default Level Level: 15. Usage Guideline Use this command to enable sending PoE usage threshold exceeding traps. Example This example shows how to enable trap for PoE event. Switch#configure terminal Switch(config)#snmp-server enable traps poe Switch(config)# 25-4 show poe power-inline This command is used to display the Power over Ethernet (PoE) status for the specified PoE port, or for all PoE ports in the switch system.
PAGE 127
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch# show poe power-inline status Interface State Class Max(W) Used(W) -----------------------------------------------eth1/0/1 Searching Class-0 0.0 0.0 eth1/0/2 Searching Class-0 0.0 0.0 eth1/0/3 Disabled Class-0 0.0 0.0 eth1/0/4 Searching Class-0 0.0 0.0 eth1/0/5 Searching Class-0 0.0 0.0 eth1/0/6 Searching Class-0 0.0 0.0 eth1/0/7 Searching Class-0 0.0 0.0 eth1/0/8 Searching Class-0 0.0 0.
PAGE 128
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch# show poe power-inline configuration Interface Admin Priority Time-Range ----------------------------------------------------eth1/0/1 auto low eth1/0/2 auto low eth1/0/3 auto low eth1/0/4 auto low eth1/0/5 auto low eth1/0/6 auto low eth1/0/7 auto low eth1/0/8 auto low day-time Switch# Display Parameters Interface The PoE interface ID.
PAGE 129
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Example This example shows how to display the PoE power system’s power information. Switch# show poe power module Unit Delivered(W) Power Budget(W) Usage-Threshold(%) Trap State ------------------------------------------------------------------1 0.0 40.0 50 Disabled Switch# Display Parameters Unit The unit ID of stacking device. Delivered The actual amount of power delivered to the PD in watts.
PAGE 130
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide reply the ping request. reset - Specifies to disable and then enable the PoE port state. notify - Specifies to send logs and traps to notify the administrator. both - Specifies to send log and trap first, and then reset the PoE port state. Default By default, this function is disabled. The default IP address of the target PD is none. The default interval for system to issue ping requests is 30 seconds.
PAGE 131
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Example This example shows how to enable the PoE PD alive check function on interface eth1/0/1-2. Switch# configure terminal Switch(config)# interface range Ethernet 1/0/1-2 Switch(config-if-range)#poe pd alive Switch(config-if-range)# This example shows how to configure the IP address of the target PD. Switch# configure terminal Switch(config)# interface Ethernet 1/0/2 Switch(config-if)# poe pd alive ip 192.168.1.
PAGE 132
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide show poe pd alive [interface INTERFACE-ID [, | -]] Parameters interface INTERFACE-ID Specifies the interface ID to display. , (Optional) Specifies a series of interfaces, or separate a range of interfaces from a previous range. No spaces before and after the comma. - (Optional) Specifies a range of interfaces. No spaces before and after the hyphen. Default None Command Mode EXEC Mode or Any Configuration Mode.
PAGE 133
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 26. Power Saving Commands 26-1 dim led This command is used to disable the port LED function. Use the no form of this command to restore the LED function. dim led no dim led Parameters None. Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command to turn off the port LED function. Use the no form of this command to restore the LED function.
PAGE 134
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide port-shutdown Specifies that power saving will be applied by scheduled port shutdown. hibernation Specifies that power saving will be applied by scheduled system hibernation. This parameter can only be used when the stacking is disabled. Default By default, all the options are disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 135
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Default Level Level: 15. Usage Guideline Use this command to enable or disable the specified port’s EEE power saving function. The Energy-Efficient Ethernet (EEE) power-saving mode saves power consumption while a link is up when there s low utilization of packet traffic. The physical interface will enter into a Low Power Idle (LPI) mode when there is no data to be transmitted.
PAGE 136
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch(config)# 26-5 power-saving hibernation time-range This command is used to configure the time range profile for the system hibernation schedule. Use the no form of this command to delete the specified time range profile. power-saving hibernation time-range PROFILE-NAME no power-saving hibernation time-range PROFILE-NAME Parameters PROFILE-NAME Specifies the name of the time range profile to be configured.
PAGE 137
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide PROFILE-NAME Specifies the name of the time range profile to be configured. The maximum length is 32 characters. Default None. Command Mode Interface Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command to add or delete a time range profile for the port shutdown schedule. When the schedule is up, the specific port will be disabled.
PAGE 138
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline If no optional keywords were specified, all power saving configuration information will be displayed. Example This example shows how to display all power saving configuration information. Switch# show power-saving Function Version: 3.
PAGE 139
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 27. Port Security Commands 27-1 clear port-security This command is used to delete the auto-learned secured MAC addresses. clear port-security {all | {address MAC-ADDR | interface INTERFACE-ID [, | -]} [vlan VLAN-ID]} Parameters all Specifies to delete all auto-learned secured entries. address MAC-ADDR Specifies to delete the specified auto -learned secured entry based on the MAC address entered.
PAGE 140
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 27-2 show port-security This command is used to display the current port security settings. show port-security [[interface INTERFACE-ID [, | -]] [address] Parameters INTEFACE-ID Specifies the ID of the interface to be displayed. , (Optional) Specifies a series of interfaces, or separate a range of interfaces from a previous range. No space is allowed before and after the comma. - (Optional) Specifies a range of interfaces.
PAGE 141
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 27-3 snmp-server enable traps port-security This command is used to enable sending SNMP notifications for port security address violation. Use the no form of the command to disable sending SNMP notifications. snmp-server enable traps port-security [trap-rate TRAP-RATE] no snmp-server enable traps port-security [trap-rate] Parameters trap-rate TRAP-RATE (Optional) Specifies the number of traps per second. The range is from 0 to 1000.
PAGE 142
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide The valid range is from 0 to 1440 in minutes. maximum VALUE (Optional) Specifies to set the maximum number of secure MAC addresses allowed. If not specified, the default value is 32. The valid range is from 1 to 64. protect (Optional) Specifies to drop all packets from the insecure hosts at the port-security process level, but does not increment the securityviolation count.
PAGE 143
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch(config)# interface Ethernet 1/0/1 Switch(config-if)# switchport port-security violation restrict Switch(config-if)# This example shows how to apply the aging time for automatically learned secure MAC addresses for interface eth1/0/1.
PAGE 144
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 28. Quality of Service (QoS) Commands 28-1 mls qos cos This command is used to configure the default Class of Service (CoS) value of a port. Use the no form of this command to revert to the default settings. mls qos cos {COS-VALUE } no mls qos cos Parameters Specifies to assign a default CoS value to a port. This CoS will be applied to the incoming untagged packets received by the port. COS-VALUE Default By default, this CoS value is 0.
PAGE 145
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide separated by commas (,) or hyphens (-) with no spaces or hyphens before and after. Specifies the range of DSCP values. DSCP-LIST Default CoS Value: 0 DSCP Value: 0-7 1 2 3 4 5 6 7 8-15 16-23 24-31 32-39 40-47 48-55 56-63 Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline The DSCP to CoS map is used by a DSCP trust port to map a DSCP value to an internal CoS value.
PAGE 146
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Specify schedule algorithms to WRR, SP for the output queue. By default, the output queue scheduling algorithm is WRR. Example This example shows how to configure the queue scheduling algorithm to the strict priority mode.
PAGE 147
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Example This example shows how to configure port eth1/0/1 to trust the DSCP mode. Switch# configure terminal Switch(config)# interface Ethernet 1/0/1 Switch(config-if)# mls qos trust dscp Switch(config-if)# 28-5 rate-limit This command is used to set the received bandwidth limit values for an interface. Use the no form of this command to disable the bandwidth limit.
PAGE 148
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 28-6 show mls qos interface This command is used to display port level QoS configurations. show mls qos interface INTERFACE-ID [, | -] {cos | scheduler| trust | rate-limit } Parameters interface INTERFACE-ID Specifies the interface ID to display. , (Optional) Specifies a series of interfaces, or separate a range of interfaces from a previous range. No space is allowed before and after the comma. - (Optional) Specifies a range of interfaces.
PAGE 149
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This example shows how to display the port trust state for eth 1/0/2 to eth 1/0/5. Switch# show mls qos interface eth1/0/2-1/0/5 trust Interface Trust State -------------- ----------------eth1/0/2 trust DSCP eth1/0/3 trust CoS eth1/0/4 trust DSCP eth1/0/5 trust CoS Switch# This example shows how to display the scheduling configuration for eth1/0/2 to eth1/0/4.
PAGE 150
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide none Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display the DSCP to CoS map infomration on the switch Example This example shows how to display the DSCP to CoS map information.
PAGE 151
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Use this command to display the QoS queueing infomration on the switch Example This example shows how to display the QoS queuing information.
PAGE 152
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 29. RADIUS Server Commands 29-1 radius-server deadtime This command is used to specify the default duration of the time to skip the unresponsive server. Use the no form of this command to revert to the default setting. radius-server deadtime MINUTES no radius-server deadtime Parameters MINUTES Specifies the dead time. The valid range is 0 to 1440 (24 hours). When the setting is 0, the unresponsive server will not be marked as dead.
PAGE 153
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 29-2 radius-server host This command is used to create a RADIUS server host. Use the no form of this command to delete a server host. radius-server host {IP-ADDRESS | IPV6-ADDRESS} [auth-port PORT] [acct-port PORT] [timeout SECONDS] [retransmit COUNT] key KEY-STRING no radius-server host {IP-ADDRESS | IPV6-ADDRESS} Parameters IP-ADDRESS Specifies the IP address of the RADIUS server.
PAGE 154
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch(config)# 29-3 show radius statistics This command is used to display RADIUS statistics for accounting and authentication packets. show radius statistics Parameters None. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Use this command to display statistics counters related to servers. Example This example shows how to display the server related statistics counters.
PAGE 155
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Display Parameters Auth Statistics for authentication packets. Acct Statistics for accounting packets. Round Trip Time The time interval (in hundredths of a second) between the most recent Response and the Request that matched it from this RADIUS server. Access Requests The number of RADIUS Access-Request packets sent to this server. This does not include retransmissions.
PAGE 156
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 30. Remote Network MONitoring (RMON) Commands 30-1 rmon collection stats This command is used to enable RMON statistics on the configured interface. Use the no form of this command to disable the RMON statistics. rmon collection stats INDEX [owner NAME] no rmon collection stats INDEX Parameters INDEX Specifies the Remote Network Monitoring (RMON) table index. The range is from 1 to 65535. owner NAME Specifies the owner string.
PAGE 157
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide INDEX Specifies the history group table index. The range is from 1 to 65535. owner NAME Specifies the owner string. The maximum length is 127. buckets NUM Specifies the number of buckets specified for the RMON collection history group of statistics. If not specified, the default is 50. The range is from 1 to 65535. interval SECONDS Specifies the number of seconds in each polling cycle. The range is from 1 to 3600.
PAGE 158
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide delta Specifies that the delta of two consecutive sampled values is monitored. absolute Specifies that the absolute sampled value is monitored. rising-threshold VALUE Specifies the rising threshold. The valid range is from 0 to 2147483647. RISING-EVENT-NUMBER (Optional) Specifies the index of the event entry that is used to notify the rising threshold crossing event. The valid range is from 1 to 65535.
PAGE 159
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide INDEX Specifies the index of the alarm entry. The valid range is from 1 to 65535. log (Optional) Specifies to generate log message for the notification. trap COMMUNITY (Optional) Specifies to generate SNMP trap messages for the notification. The maximum length is 127. owner NAME (Optional) Specifies the owner string. The maximum length is 127. description STRING (Optional) Specifies a description for the RMON event entry.
PAGE 160
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline This command displays the RMON alarm table. Example This example shows how to displays the RMON alarm table. Switch# show rmon alarm Alarm index 23, owned by IT Monitors OID: 1.3.6.1.2.1.2.2.1.10.
PAGE 161
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Event 2, owned by manager2 Description is Errors Event trigger action: log & trap Last triggered time: Switch# 30-7 show rmon history This command is used to display RMON history statistics information. show rmon history Parameters None. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command displays the history of the statistics for all of the configured entries.
PAGE 162
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Fragments: 2, Jabbers: 1 CRC alignment errors: 0, Collisions: 0 Drop events : 0 Switch# 30-8 show rmon statistics This command is used to display RMON Ethernet statistics. show rmon statistics Parameters None. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline Statistics for all of the configured entries are displayed. Example This example shows how to display the RMON statistics.
PAGE 163
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 30-9 snmp-server enable traps rmon This command is used to enable the RMON trap state. snmp-server enable traps rmon [rising-alarm | falling-alarm] no snmp-server enable traps rmon [rising-alarm | falling-alarm] Parameters rising-alarm (Optional) Specifies to configure the rising alarm trap state. falling-alarm (Optional) Specifies to configure the falling alarm trap state. Default By default, this option is disabled.
PAGE 164
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 31. Safeguard Engine Commands 31-1 cpu-protect safeguard This command is used to enable the Safeguard Engine. Use the no form of this command to disable the Safeguard Engine. cpu-protect safeguard no cpu-protect safeguard Parameters None. Default By default, Safeguard Engine is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 165
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Default Level Level: 1. Usage Guideline This command is used to display the status of the Safeguard Engine. Example This example shows how to display the current status of the Safeguard Engine.
PAGE 166
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 32. Simple Network Management Protocol(SNMP) Commands 32-1 show snmp-server This command is used to display the SNMP server’s global state settings and trap related settings. show snmp-server [traps] Parameters traps (Optional) Specifies to display trap related settings. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1.
PAGE 167
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide warmstart : Disabled Switch# 32-2 snmp-server This command is used to enable the SNMP agent. Use the no form of this command to disable the SNMP agent. snmp-server no snmp-server Parameters None. Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 168
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide maximum length is 255 characters The syntax is a general string that allows spaces. Default None. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline This command configures the system contact information for management of the device. Example This example shows how to configure the system contact information with the string MIS Department.
PAGE 169
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch(config)# 32-5 snmp-server enable traps snmp This command is used to enable the sending of all or specific SNMP notifications. Use the no form of this command to disable sending of all or specific SNMP notifications.
PAGE 170
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch(config)# snmp-server host 10.9.18.100 version 2c public Switch(config)# This example shows how to enable the SNMP authentication traps. Switch# configure terminal Switch(config)# snmp-server enable traps snmp authentication Switch(config)# 32-6 snmp-server location This command is used to configure the system’s location information. Use the no form of this command to remove the setting.
PAGE 171
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 32-7 snmp-server name This command is used to configure the system’s name information. Use the no form of this command to remove the setting. snmp-server name NAME no snmp-server name Parameters NAME Specifies the string that describes the SNMP server name information. Spaces are not allowed here. Default By default, this name is “Switch”. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 172
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 32-8 show snmp This command is used to display the SNMP settings. show snmp {community | host | view | group | engineID } Parameters community Specifies to display SNMP community information. host Specifies to display SNMP trap recipient information. view Specifies to display SNMP view information. group Specifies to display SNMP group information. engineID Specifies to display SNMP local engine ID information. Default None.
PAGE 173
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This example shows how to display the SNMP server host setting. Switch# show snmp host Host IP Address : 10.20.30.40 SNMP Version V1 : Community Name : UDP Port : public 162 Host IP Address : 10.10.10.1 SNMP Version V3 noauthnopriv : SNMPv3 User Name : user1 UDP Port : 162 Total Entries: 2 Switch# This example shows how to display the MIB view setting.
PAGE 174
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This example shows how to display the SNMP group setting.
PAGE 175
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This example shows how to display the SNMP engine ID. Switch# show snmp engineID Local SNMP engineID : 800000ab03000102183401 Switch# 32-9 show snmp user This command is used to display information about the configured SNMP user. show snmp user [USER-NAME] Parameters USER-NAME (Optional) Specifies the name of a specific user to display SNMP information. Default None. Command Mode EXEC Mode or Any Configuration Mode.
PAGE 176
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 32-10 snmp-server community This command is used to configure the community string to access the SNMP. Use the no form of this command to remove the community string, snmp-server community COMMUNITY-STRING [ro | rw] [view VIEW-NAME] no snmp-server community COMMUNITY-STRING Parameters COMMUNITY-STRING Specifies the community string with a maximum of 32 characters. Spaces are not allowed here. ro (Optional) Specifies read-only access.
PAGE 177
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide snmp-server engineID local 32-11 This command is used to specify the SNMP engine ID on the local device. Use the no command to revert the SNMP engine ID to the default. snmp-server engineID local ENGINEID-STRING no snmp-server engineID local Parameters ENGINEID-STRING Specifies the engine ID string of a maximum of 24 characters. Default None. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 178
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide v2c Specifies that the group user can use the SNMPv2c security model. v3 Specifies that the group user can use the SNMPv3 security model. auth Specifies to authenticate the packet but not encrypt it. noauth Specifies not to authenticate and not to encrypt the packet. priv Specifies to authenticate and encrypt the packet. read READ-VIEW (Optional) Specifies a read-view that the group user can access.
PAGE 179
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch# configure terminal Switch(config)# snmp-server view interfacesMibView 1.3.6.1.2.1.2 included Switch(config)# snmp-server group guestgroup v3 auth read interfacesMibView Switch(config)# snmp-server group guestgroup v2c read CommunityView write CommunityView Switch(config)# 32-13 snmp-server host This command is used to specify the recipient of the SNMP notification. Use the no form of this command to remove the recipient.
PAGE 180
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide will be sent in the trap protocol data unit (PDU). For SNMPv3, the notification will be sent in the SNMPv2TRAP-PDU with the SNMPv3 header. When specifying to send the trap packets in SNMPv1 or SNMPv2c to a specific host, the specified community string acts as the community string in the trap packets.
PAGE 181
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Parameters USER-NAME Specifies a username of a maximum of 32 characters. The syntax is general string that does not allow spaces. GROUP-NAME Specifies the name of the group to which the user belongs. The syntax is general string that does not allow spaces. v1 Specifies that the user uses the SNMPv1 security model. v2c Specifies that the user uses the SNMPv2c security model. v3 Specifies that the user uses the SNMPv3 security model.
PAGE 182
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch# configure terminal Switch(config)# snmp-server user user1 public v3 entrypted auth md5 112233445566778899AABBCCDDEE Switch(config)# 32-15 snmp-server view This command is used to create or modify a view entry. Use the no form of this command to remove a specified SNMP view entry. snmp-server view VIEW-NAME OID-TREE {included | excluded} no snmp-server view VIEW-NAME Parameters VIEW-NAME Specifies the name of the view entry.
PAGE 183
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Use this command to create a view of MIB objects. Example This example shows how to create a MIB view called “interfacesMibView” and define an SNMP group “guestgroup” with “InterfaceMIBView” as the read view. Switch# configure terminal Switch(config)# snmp-server view interfacesMibView 1.3.6.1.2.1.
PAGE 184
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 33. Spanning Tree Protocol (STP) Commands 33-1 show spanning-tree This command is used to display the information of spanning tree protocol operation. This command is only for STP and RSTP. show spanning-tree [interface [INTERFACE-ID [, | -]] Parameters interface INTERFACE-ID Specifies the interface ID to display. , (Optional) Specifies a series of interfaces, or separate a range of interfaces from a previous range.
PAGE 185
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 33-2 show spanning-tree configuration interface This command is used to display the information about STP interface related configuration. show spanning-tree configuration interface [INTERFACE-ID [, | -]] Parameters interface INTERFACE-ID Specifies the interface ID to display. , (Optional) Specifies a series of interfaces, or separate a range of interfaces from a previous range. No space before and after the comma.
PAGE 186
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide new-root (Optional) Specifies the sending of STP new root notification. topology-chg (Optional) Specifies the sending of STP topology change notification. Default By default, these options are disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command to enable the sending of notification traps.
PAGE 187
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Usage Guideline Use this command in the global configuration mode to enable the global spanning-tree function. Example This example shows how to enable the spanning-tree function. Switch# configure terminal Switch(config)# spanning-tree global state enable Switch(config)# 33-5 spanning-tree mode This command is used to configure the STP mode. Use the no form of this command to revert to the default setting.
PAGE 188
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 33-6 spanning-tree portfast This command is used to specify the port’s fast mode. Use the no form of this command to revert to the default setting. spanning-tree portfast {disable | edge| network} no spanning-tree portfast Parameters disable Specifies to set the port to the port fast disabled mode. edge Specifies to set the port to the port fast edge mode. network Specifies to set the port to the port fast network mode.
PAGE 189
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide spanning-tree priority PRIORITY no spanning-tree priority Parameters PRIORITY Specifies that the bridge priority and bridge MAC address together forms the Spanning-Tree Bridge-ID, which is an important factor in the Spanning-Tree topology. The range is from 0 to 61440. Default By default, this value is 32768. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 190
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Level: 15. Usage Guideline If enabled, the received STP BPDU will be forwarded to all VLAN member ports in the untagged form. The command does not take effect if the Layer 2 protocol tunnel is enabled for STP. Example This example shows how to enable the forwarding of STP BPDUs.
PAGE 191
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 34. Storm Control Commands 34-1 storm-control This command is used to configure the device to protect the device from broadcast, multicast, and DA unknown packet storm attacks. Use the no form of this command to restore the function to its default settings.
PAGE 192
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Parameters None. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline None. Example This example shows how to display the current storm control settings.
PAGE 193
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 34-3 spanning-tree priority This command is used to configure the bridge priority. It is only used for RSTP and STP versions. Use the no form of this command to restore to the default setting. spanning-tree priority PRIORITY no spanning-tree priority Parameters PRIORITY Specifies that the bridge priority and bridge MAC address together forms the Spanning-Tree Bridge-ID, which is an important factor in the Spanning-Tree topology.
PAGE 194
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 35. Surveillance VLAN Commands 35-1 surveillance vlan This command is used to enable the global surveillance VLAN state and configure the surveillance VLAN. Use the no form of this command to disable the surveillance VLAN state. surveillance vlan VLAN-ID no surveillance vlan Parameters VLAN-ID Specifies the ID of the surveillance VLAN. The range is from 2 to 4094. Default By default, this option is disabled.
PAGE 195
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Example This example shows how to enable the surveillance VLAN function and configure VLAN 1001 as a Surveillance VLAN. Switch# config terminal Switch(config)# surveillance vlan 1001 Switch(config)# 35-2 surveillance vlan aging This command is used to configure the aging time for aging out the surveillance VLAN dynamic member ports. Use the no form of this command to revert to the default setting.
PAGE 196
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This command is used to enable the surveillance VLAN state of ports. Use the no form of this command to disable the surveillance VLAN state of ports. surveillance vlan enable no surveillance vlan enable Parameters None. Default By default, this option is disabled. Command Mode Interface Configuration Mode. Command Default Level Level: 15. Usage Guideline The command is available for physical port and port-channel interface configuration.
PAGE 197
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide MAC-ADDRESS Specifies the OUI MAC address. MASK Specifies the OUI MAC address matching bitmask. component-type (Optional) Specifies surveillance components that could be autodetected by surveillance VLAN. vms (Optional) Specifies the surveillance components type as Video Management Server (VMS). vms-client (Optional) Specifies the surveillance components type as VMS client.
PAGE 198
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 35-5 surveillance vlan onvif-discover-port This command is used to configure the TCP/UDP port number for RTSP stream snooping. Use the no form of this command to revert to the default setting. surveillance vlan onvif-discover-port VALUE no surveillance vlan onvif-discover-port Parameters VALUE Enter the TCP/UDP port number here. The range is either 554, or from 1025 to 65535. Default By default, this value is 554.
PAGE 199
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide MAC-ADDRESS (Optional) Enter the MAC address of the IPC that is recognized with ONVIF. enable Specifies that the ONVIF recognition IPC state will be enabled. disable Specifies that the ONVIF recognition IPC state will be disabled. Default By default, this feature is enabled. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 200
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline This command is used to configure the description of the ONVIF recognized IPC with only the IP address of the IPC, or both the IP and MAC address of the IPC. If there is more than one IPC with the same IP address and the MAC addresses of those IPCs are not specified, the description of those IPCs will be configured.
PAGE 201
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This example shows how to define the description of the NVR with an IP address of 172.18.60.2 to 'nvr1'. Switch# config terminal Switch(config)# surveillance vlan onvif-nvr 172.18.60.2 description nvr1 Switch(config)# 35-9 surveillance vlan qos This command is used to configure the CoS priority for the incoming surveillance VLAN traffic. Use the no form of this command to revert to the default settings.
PAGE 202
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Parameters device Specifies to display the learned surveillance devices information. interface (Optional) Specifies to display surveillance VLAN information of ports. INTERFACE-ID (Optional) Specifies the port to be displayed. , (Optional) Specifies a series of interfaces, or separate a range of interfaces from a previous range. No space is allowed before and after the comma. - (Optional) Specifies a range of interfaces.
PAGE 203
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide B0-C5-54-00-00-00 FF-FF-FF-80-00-00 D-Link Device IP Surveillance Device F0-7D-68-00-00-00 FF-FF-FF-F0-00-00 D-Link Device IP Surveillance Device Total OUI : 4 Switch# 35-11 show surveillance vlan onvif-ipc interface This command is used to display ONVIF-based IPC information. show surveillance vlan onvif-ipc interface [INTERFACE-ID [,|-]] {brief | detail} Parameters INTERFACE-ID (Optional) Specifies the port to be displayed.
PAGE 204
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Description : P3384-VE Total Entries: 1 Switch# This example shows how to display detailed ONVIF-based IP camera information. Switch# show surveillance vlan onvif-ipc interface Ethernet 1/0/1 detail Interface : eth1/0/1 IP Address : 10.90.90.1 MAC Address : 00-01-02-03-04-05 Model : P3384-VE Manufacturer : D-Link State : Enabled Description : P3384-VE Protocol : ONVIF Power Consumption: 1.9W/15W PoE : 802.
PAGE 205
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command is used to display ONVIF-based NVR and group information. The group ID is the group ID of the IPCs that belong to the NVR group. NVRs and IPCs, managed by it, must have the same group ID. Example This example shows how to display ONVIF-based NVR information.
PAGE 206
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 36. Switch Port Commands 36-1 duplex This command is used to configure the physical port interface’s duplex setting. Use the no form of command to revert to the default setting. duplex {full | half | auto} no duplex Parameters full Specifies that the port operates in the full-duplex mode. half Specifies that the port operates in the half-duplex mode. auto Specifies that the port’s duplex mode will be determined by autonegotiation.
PAGE 207
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide no flowcontrol Parameters on Specifies to enable a port to send PAUSE frames or process PAUSE frames from remote ports. off Specifies to disable the ability for a port to send or receive PAUSE frames. Default By default, this option is disabled. Command Mode Interface Configuration Mode. Command Default Level Level: 15.
PAGE 208
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide mode. cross Specifies to force the port interface’s MDIX state to the cross mode. Default By default, this option is set as auto. Command Mode Interface Configuration Mode. Command Default Level Level: 15. Usage Guideline This command cannot be applied to a port when the medium of the port interface is fiber.
PAGE 209
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Mode Interface Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command is to configure the physical port interface’s speed settings. Example This example shows how to configure eth1/0/3 to 1000 Mbps.
PAGE 210
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 37. System File Management Commands 37-1 boot image This command is used to specify image that will be used as the image file for the next boot. boot image {image1 | image2} Parameters Image1 Specifies the image1 for the next boot. Image2 Specifies the image2 for the next boot. Default By default, there is an image file as the boot image. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 211
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide is to upload the running configuration or save the running configuration as the startup configuration or to save it as the file in the file system. If flash: [PATH-FILE-NAME] is specified as the SOURCE-URL, the purpose is to specify the source file to be copied in the file system. If log is specified as the SOURCE-URL, the system log can be retrieved to the TFTP server.
PAGE 212
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Building configuration... % Saving 1072 bytes to TFTP server 10.10.1.141: /office.cfg Switch# This example shows how to save the system’s running configuration into the FLASH memory and uses it as the next boot configuration. Switch# copy running-config startup-config Building configuration... % Saving 1072 bytes to flash:startup-config Switch# 37-3 clear running-config This command is used to clear the system’s running configuration.
PAGE 213
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 37-4 reset system This command is used to reset the system, clear the system’s configuration. reset system Parameters None. Default None. Command Mode Privilege EXEC Mode. Command Default Level Level: 15. Usage Guideline Use this command to clear the system’s configuration. The configuration data will revert to the default settings.
PAGE 214
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Level: 1. Usage Guideline This command is used to display the boot image setting. Example This example shows how to display system boot information. Switch# show boot Unit 1 Boot image: flash:/R1.10.B014.dat Image info (* : Next bootup image) : * R1.10.B014.dat (Image1) R1.10.B014.dat (Image2) Switch# 37-6 show running-config This command is used to display the commands in the running configuration file. show running-config Parameters None.
PAGE 215
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide multicast filtering-mode filter-unregistered clock timezone + 0 0 ip http secure-server ip http timeout-policy idle 60 snmp-server enable traps storm-control multicast level pps 8 cpu-protect safeguard threshold 60 40 ! ! interface Ethernet 1/0/1 switchport mode access ! interface Ethernet 1/0/2 switchport mode access mls qos cos 3 ! interface Ethernet 1/0/3 switchport mode access rate-limit input 1300 mls qos scheduler sp speed 1000 flowcontrol on
PAGE 216
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide ! interface Ethernet 1/0/12 switchport mode access ! interface vlan 1 ip address 10.10.1.19 255.255.248.
PAGE 217
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 37-7 show startup-config This command is used to display the content of the startup configuration file. show startup-config Parameters None. Default None. Command Mode Privileged EXEC Mode. Command Default Level Level: 15. Usage Guideline This command displays the configuration settings that the system will be initialized with. Example This example shows how to display the content of the startup configuration file.
PAGE 218
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 38. System Log Commands 38-1 clear logging This command is used to delete log messages. clear logging Parameters None. Default None. Command Mode Privilege EXEC Mode. Command Default Level Level: 15. Usage Guideline This command deletes all the log messages in the system. Example This example shows how to delete all the log messages in the system.
PAGE 219
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide The content of the logging messages will be saved to the FLASH immediately such that the message can be restored on reboot. The content of the logged messages in the FLASH will be reloaded into the logging buffer on reboot. Example This example shows how to enable the logging of messages .
PAGE 220
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide The following is a table for the facility. Numerical code Facility 16 Local use 0 (local0). 17 Local use 1 (local1). 18 Local use 2 (local2). 19 Local use 3 (local3). 20 Local use 4 (local4). 21 Local use 5 (local5). 22 Local use 6 (local6). 23 Local use 7 (local7). Example This example shows how to enable the logging of system messages with a severity higher than warnings to the remote host 10.10.1.141.
PAGE 221
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Example This example shows how to configure VLAN 100 as the source interface for SYSLOG packets. Switch# config t Switch(config)# logging source-interface vlan 100 ERROR : Syslog source interface only support on management vlan interface Switch(config)# 38-5 show logging This command is used to display the system messages logged in the local message buffer. show logging Parameters none Default None.
PAGE 222
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 39. Secure Shell(SSH) Commands 39-1 ip ssh server This command is used to enable the SSH server function. Use the no form of this command to disable the SSH server function. ip ssh server no ip ssh server Parameters None. Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command to enable the SSH server function.
PAGE 223
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Level: 1. Usage Guideline Use this command to display the SSH configuration settings. Example This example shows how to display the SSH configuration settings. Switch# show ip ssh IP SSH server : Enabled SSH server mode : V2 Switch# 40. Time and SNTP Commands 40-1 clock set This command is used to manually set the system’s clock.
PAGE 224
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide replaced by the new synced clock. Example This example shows how to manually set the software clock to 3:45 p.m. on Mar 16, 2017. Switch# clock set 15:45:00 16 mar 2017 Switch# 40-2 clock summer-time This command is used to configure the system to automatically switch to summer time (daylight saving time). Use the no form of this command to configure the Switch to not automatically switch over to summer time.
PAGE 225
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 40-3 clock timezone This command is used to set the time zone for display purposes. Use the no form of this command to revert to the default setting. clock timezone {+ | -} HOURS-OFFSET [MINUTES-OFFSET] no clock timezone Parameters +|- +: Specifies that time to be added to the UTC. - : Specifies that time to be subtracted from the UTC. HOURS-OFFSET Specifies the hours difference from UTC.
PAGE 226
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command also indicates the clock’s source. The clock source can be “No Time Source” or“SNTP”. Example This example shows how to display the current time.
PAGE 227
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide SNTP Poll Interval : 720 sec SNTP Server Status: SNTP Server Stratum Version Last Receive ---------------------------------------------- ------- ------- --------------10.10.1.112 0 4 - ---------------------------------------------- ------- ------- --------------Total Entries : 1 Switch# 40-6 sntp server This command is used to allow the system clock to be synchronized with an SNTP time server.
PAGE 228
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 40-7 sntp enable This command is used to enable the SNTP function. Use the no form of this command to disable the SNTP function. sntp enable no sntp enable Parameters None. Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline This command is used to enable or disable the SNTP function. Example This example shows how to enable the SNTP function.
PAGE 229
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Usage Guideline This command is used to set the polling interval. Example This example shows how to configure the interval to 100 seconds. Switch# configure terminal Switch(config)# sntp interval 100 Switch(config)# 41. Time Range Commands 41-1 periodic This command is used to specify the period of time for a time range profile. This command is used in the time-range configuration mode.
PAGE 230
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Switch(config-time-range)# no periodic daily 9:00 to 12:00 Switch(config-time-range)# 226
PAGE 231
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 41-2 show time-range This command is used to display the time range profile configuration. show time-range [NAME] Parameters NAME (Optional) Specifies the name of the time-range profile to be displayed. Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline If the name is not specified, all configured time-range profiles will be displayed.
PAGE 232
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 41-3 time-range This command is used to enter the time range configuration mode to define a time range. Use the no command to delete a time range. time-range NAME no time-range NAME Parameters NAME Specifies the name of the time-range profile to be configured. The maximum length is 32 characters. Default None. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 233
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 42. Traffic Segmentation Commands 42-1 show traffic-segmentation forward This command is used to display the traffic segmentation for some ports or all ports. show traffic-segmentation forward [interface INTERFACE-ID [, | -]] Parameters interface INTERFACE-ID (Optional) Specifies ID of an interface. The acceptable interface will be physical port or port channel.
PAGE 234
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 42-2 traffic-segmentation forward This command is used to restrict the Layer 2 packet forwarding domain of packets received by the configured port. Use the no form of this command to remove the specification of forwarding domain. traffic-segmentation forward interface INTERFACE-ID [, | -] no traffic-segmentation forward interface INTERFACE-ID [, | -] Parameters interface INTERFACE-ID Specifies the ID of an interface allowed.
PAGE 235
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 43. Virtual LAN (VLAN) Commands 43-1 acceptable-frame This command is used to set the acceptable types of frames by a port. Use the no form of this command to revert to the default settings. acceptable-frame {tagged-only | untagged-only | admit-all} no acceptable-frame Parameters tagged-only Specifies that only tagged frames are admitted. untagged-only Specifies that only untagged frames are admitted.
PAGE 236
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 43-2 ingress-checking This command is used to enable ingress checking for frames received by a port. Use the no command to disable the ingress check. ingress-checking no ingress-checking Parameters None. Default By default, this option is enabled. Command Mode Interface Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command to enable ingress checking for packets received by the interface.
PAGE 237
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Default None. Command Mode EXEC Mode or Any Configuration Mode. Command Default Level Level: 1. Usage Guideline This command is used to display the parameters for all configured VLANs or one VLAN on the Switch. Example This example shows how to display all the current VLAN entries.
PAGE 238
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide VLAN mode : Access Access VLAN : 1 Ingress checking : Disabled Acceptable frame type : Admit-All Switch# 43-4 switchport access vlan This command is used to specify the access VLAN for an interface. Use the no form of this command to revert to the default setting. switchport access vlan VLAN-ID no switchport access vlan Parameters access vlan VLAN-ID Specifies the access VLAN of the interface.
PAGE 239
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide switchport hybrid allowed vlan {[add] {tagged | untagged} | remove} VLAN-ID [, | -] no switchport hybrid allowed vlan Parameters add Specifies the port will be added into the specified VLAN(s). remove Specifies the port will be removed from the specified VLAN(s). tagged Specifies the port as a tagged member of the specified VLAN(s). untagged Specifies the port as an untagged member of the specified VLAN(s).
PAGE 240
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 43-6 switchport hybrid native vlan This command is used to specify the native VLAN ID of a hybrid port. Use the no form of this command to reset the native VLAN to the default setting. switchport hybrid native vlan VLAN-ID no switchport hybrid native vlan Parameters vlan VLAN-ID Specifies the native VLAN of a hybrid port. Default By default, the native VLAN of a hybrid port is VLAN 1. Command Mode Interface Configuration Mode.
PAGE 241
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide hybrid Specifies the port as a hybrid port. trunk Specifies the port as a trunk port. Default By default, this option is hybrid. Command Mode Interface Configuration Mode. Command Default Level Level: 15. Usage Guideline When a port is set to access mode, this port will be an untagged member of the access VLAN configured for the port. When a port is set to hybrid mode, the port can be an untagged or tagged member of any VLAN configured.
PAGE 242
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide , (Optional) Specifies a series of VLANs, or separate a range of VLANs from a previous range. No space is required before and after the comma. - (Optional) Specifies a range of VLANs. No space is required before and after the hyphen. Default By default, all VLANs are allowed. Command Mode Interface Configuration Mode. Command Default Level Level: 15. Usage Guideline This command only takes effect when the interface is set to trunk mode.
PAGE 243
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Level: 15. Usage Guideline The command only takes effect when the interface is set to trunk mode. When a trunk port native VLAN is set to tagged mode, normally the acceptable frame type of the port should be set to “tagged- only” to only accept tagged frames.
PAGE 244
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide of a new VLAN, the VLAN will be automatically created. Use the no vlan command to remove a VLAN. The default VLAN cannot be removed. If the removed VLAN is a port’s access VLAN, the port’s access VLAN will be reset to VLAN 1. Example This example shows how to add new VLANs, assigning the new VLANs with the VLAN IDs 1000 to 1005.
PAGE 245
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 44. Voice VLAN Commands 44-1 voice vlan This command is used to enable the global voice VLAN state and configure the voice VLAN. Use the no form of this command to disable the voice VLAN state. voice vlan VLAN-ID no voice vlan Parameters VLAN-ID Specifies the ID of the voice VLAN. The valid range is from 2 to 4094. Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 246
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Parameters MINUTES Specifies the aging time of the voice VLAN. The valid range is from 1 to 65535 minutes. Default By default, this value is 720 minutes. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command to configure the aging time for aging out the voice device and the voice VLAN automatically learned member ports.
PAGE 247
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide function. Example This example shows how to enable the voice VLAN function on the physical port eth1/0/1. Switch# configure terminal Switch(config)# interface Ethernet 1/0/1 Switch(config-if)# voice vlan enable Switch(config-if)# 44-4 voice vlan mac-address This command is used to add the user-defined voice device OUI. Use the no form of this command to delete the user-defined voice device OUI.
PAGE 248
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Usage Guideline Use this command to add a user-defined OUI for the voice VLAN. The OUI for the voice VLAN is used to identify the voice traffic by using the voice VLAN function. If the source MAC addresses of the received packet matches any of the OUI patterns, the received packet is determined as a voice packet. The user-defined OUI cannot be the same as the default OUI. The default OUI cannot be deleted.
PAGE 249
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide packets, the switch will change its priority. When the voice device sends untagged packets, it will forward them in voice VLAN. When the switch receives LLDP-MED packets, it checks the VLAN ID, tagged flag, and priority flag. The switch should follow the tagged flag and priority setting. If auto learning is disabled, the user should use the switchport hybrid vlan command to configure the port as a voice VLAN tagged or untagged member port.
PAGE 250
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 44-7 show voice vlan This command is used to display the voice VLAN configurations. show voice vlan [interface [INTERFACE-ID [, | -]]] show voice vlan {device | lldp-med device} [interface INTERFACE-ID [, | -]] Parameters interface (Optional) Specifies to display voice VLAN information of ports. INTERFACE-ID (Optional) Specifies the interface to display.
PAGE 251
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 00-0F-E2-00-00-00 FF-FF-FF-00-00-00 Huawei&3COM 00-60-B9-00-00-00 FF-FF-FF-00-00-00 NEC&Philips 00-D0-1E-00-00-00 FF-FF-FF-00-00-00 Pingtel 00-E0-75-00-00-00 FF-FF-FF-00-00-00 Veritel 00-E0-BB-00-00-00 FF-FF-FF-00-00-00 3COM 00-02-03-00-00-00 FF-FF-FF-00-00-00 User1 Total OUI: 9 Switch# This example shows how to display the voice VLAN information of ports.
PAGE 252
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Index : 2 Interface : eth1/0/2 Chassis ID Subtype : MAC Address Chassis ID : 00-E0-BB-00-00-12 Port ID Subtype : Network Address Port ID : 172.18.1.
PAGE 253
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 45. Web Authentication Commands 45-1 web-auth enable This command is used to enable the Web authentication function on the port. Use the no form of this command to disable the Web authentication function. web-auth enable no web-auth enable Parameters None. Default By default, this option is disabled. Command Mode Interface Configuration Mode. Command Default Level Level: 15.
PAGE 254
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 45-2 web-auth page-element This command is used to customize the Web authentication page elements. Use the no form of this command to revert to the default setting.
PAGE 255
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide This example shows how to modify two lines of the copyright information at the bottom of the authentication page with: Line 1: Copyright @ 2018 All Rights Reserved Line 2: Site: http://support.website.com Switch# configure terminal Switch(config)# web-auth page-element copyright-line 1 title Copyright @ 2018 All Rights Reserved Switch(config)# web-auth page-element copyright-line 2 title Site: http://support.website.
PAGE 256
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide 45-4 web-auth system-auth-control This command is used to enable the Web authentication function globally on the Switch. Use the no form of this command to disable the Web authentication function globally on the Switch. web-auth system-auth-control no web-auth system-auth-control Parameters None. Default By default, this option is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15.
PAGE 257
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Command Mode Global Configuration Mode. Command Default Level Level: 12. Usage Guideline The virtual IP of Web authentication is just the characterization of the Web authentication function on the Switch. All Web authentication processes communicate with this IP address, however, the virtual IP does not respond to any ICMP packet or ARP request.
PAGE 258
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Appendix A - System Log Entries The following table lists all possible entries and their corresponding meanings that will appear in the System Log of this switch. Auto Surveillance VLAN Log Description Severity Event description: When a new surveillance device is detected on an interface. Log Message: New surveillance device detected (, MAC: ) Parameters description: interface-id: Interface name.
PAGE 259
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide mode: Represent the mode of ASV 2.0. And the mode can be standard or surveillance. DDM Log Description Severity Event description: when the any of SFP parameters exceeds from the warning Warning threshold. Log Message: Optical transceiver warning threshold exceeded Parameters description: interface-id: port interface ID. component: DDM threshold type.
PAGE 260
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Interface Log Description Severity Event description: When port is down Log Message: Port < interface-id> link down Parameters description: interface-id: Interface name Informational Event description: When port is up Log Message: Port < interface-id> link up, Parameters description: interface-id: Interface name link-speed: port link speed.
PAGE 261
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Event description: Login through telnet unsuccessfully. Log Message: Login failed through Telnet (Username: , IP: ) Parameters description: username: Represent current login user. ipaddr: Represent client IP address. Warning Event description: Telnet session timed out. Log Message: Telnet session timed out (Username: , IP: ) Parameters description: username: Represent current login user.
PAGE 262
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Safeguard Log Description Severity Event description: the host enters the mode of exhausted. Log Message: Unit , Safeguard Engine enters EXHAUSTED mode. Parameters description: unit-id: The Unit ID Warning Event description: the host enters the mode of normal. Log Message: Unit , Safeguard Engine enters NORMAL mode.
PAGE 263
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide interface-id: Interface name. mac-address: Voice device MAC address Event description: When an interface which is in auto voice VLAN mode joins the voice VLAN Log Message: < interface-id > add into voice VLAN Parameters description: interface-id: Interface name.
PAGE 264
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Event description: When a host fail to pass the authentication. Message: Web-Authentication host login fail (Username: , IP: , MAC: , , VID: ) Parameters description: Username: The host username. IP: The host IP address mac-address: The host MAC addresses. interface-id: The interface on which the host is authenticated. vlan-id: The VLAN ID on which the host exists.
PAGE 265
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Appendix B - Trap Entries The following table lists all possible trap log entries and their corresponding meanings that will appear in the switch. Authentication Fail Trap Name Description OID authenticationFailure An authenticationFailure trap signifies that the SNMPv2 entity, acting in an agent role, has received a protocol message that is not properly authenticated.
PAGE 266
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide LLDP Trap Name Description OID lldpRemTablesChange A lldpRemTablesChange notification is sent when the value of lldpStatsRemTableLastChangeTime changes. It can be utilized by an NMS to trigger LLDP remote systems table maintenance polls. Binding objects: (1) lldpStatsRemTablesInserts (2) lldpStatsRemTablesDeletes (3) lldpStatsRemTablesDrops (4) lldpStatsRemTablesAgeouts 1.0.8802.1.1.2. 0.0.
PAGE 267
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide linkUp A notification is generated when port linkup. Binding objects: (1) ifIndex (2) ifAdminStatus (3) ifOperStatu 1.3.6.1.6.3.1.1.5 .4 linkDown A notification is generated when port linkdown. Binding objects: (1) ifIndex (2) ifAdminStatus (3) ifOperStatu 1.3.6.1.6.3.1.1.5 .3 Trap Name Description OID dPortSecMacAddrViolatio n When the port security trap is enabled, new MAC addresses that violate the pre-defined port security 1.14.8.0.
PAGE 268
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide (2) isnaSessionAuthVlan (3) isnaSessionClientMacAddress (4) isnaSessionClientAddrType (5) isnaSessionClientAddress (6) isnaSessionAuthUserName 264
PAGE 269
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide Appendix C - IETF RADIUS Attributes Support Remote Authentication Dial-In User Service (RADIUS) attributes carry specific authentication, authorization, information and configuration details for the request and reply. This appendix lists the RADIUS attributes currently supported by the switch. RADIUS attributes are supported by the IETF standard and Vendor-Specific Attribute (VSA).