Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date 1.0 May 25th, 2010 Description • First release version Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
Table of Contents Table of Contents Preface ............................................................... i Manual Revisions ............................................................... i Trademarks ........................................................................ i Product Overview ...................................................1 Package Contents .............................................................. 1 System Requirements .......................................................
Table of Contents Wireless .................................................................... 45 Support ..................................................................... 46 Wireless Security ................................................. 47 What is WPA? ................................................................. 47 Wireless Connection Setup Wizard .................................. 48 Conigure WPA-Personal (PSK) ...................................... 51 Connect to a Wireless Network .......
Section 1 - Product Overview Product PackageOverview Contents • D-Link DIR-600 Wireless Router • Power Adapter • Ethernet Cable Note: Using a power supply with a different voltage rating than the one included with the DIR-600 will cause damage and void the warranty for this product. The product must be used with the power adapter included with the device. Note: Always attach the power cord plug to the power supply, before inserting the power cord and connected power supply to the wall outlet.
Section 1 - Product Overview System Requirements Network Requirements • An Ethernet-based Cable or DSL modem • IEEE 802.11n/g wireless clients • 10/100 Ethernet Computer with the following: • Windows®, Macintosh, or Linux-based operating system • An installed Ethernet adapter Web-based Coniguration Utility Requirements Browser Requirements: • Internet Explorer 6.0 or higher • Mozilla 1.7.12 or higher • Firefox 1.5 or higher • Safari 1.0 or higher (with Java 1.3.1 or higher) • Flock 0.7.
Section 1 - Product Overview Features • Faster Wireless Networking - The DIR-600 provides up to 150Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. • Compatible with 802.11g Devices - The DIR-600 is still fully compatible with the IEEE 802.11g standard, so it can connect with existing 802.11g PCI, USB and Cardbus adapters.
Section 1 - Product Overview Hardware Overview Connections Power Receptor Receptor for the supplied power adapter. Internet Port The auto MDI/MDIX Internet port is the connection for the Ethernet cable to the cable or DSL modem. Reset Pressing the Reset button restores the router to its original factory default settings. LAN Ports (1-4) Connect Ethernet devices such as computers, switches, and hubs.
Section 1 - Product Overview Hardware Overview LEDs WLAN LED A solid light indicates that the wireless segment is ready. This LED blinks during wireless data transmission. Internet LED A solid light indicates connection on the Internet port. This LED blinks during data transmission. Local Network LEDs A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4. This LED blinks during data transmission. Power LED A solid light indicates a proper connection to the power supply.
Section 2 - Installation Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage. Before you Begin • Please conigure the router with the computer that was last connected directly to your modem. • You can only use the Ethernet port on your modem.
Section 2 - Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Section 2 - Installation Connect to Cable/DSL/Satellite Modem If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below: 1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down your computer. 3.
Section 2 - Installation Connect to Another Router If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network: • Disable UPnP™ • Disable DHCP • Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address from your other router. To connect to another router, please follow the steps below: 1.
Section 2 - Installation 6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the Internet port of the D-Link router. 8. You may now use the other 3 LAN ports to connect other Ethernet devices and computers. To conigure your wireless network, open a web browser and enter the IP address you assigned to the router.
Section 3 - Coniguration Coniguration This section will show you how to conigure your new D-Link wireless router using the web-based coniguration utility. Web-based Coniguration Utility To access the Easy Setup Wizard or coniguration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1). DIR-600 will detect WAN connection type.
Section 3 - Coniguration Easy Setup Wizard Once logged into the web interface of the router, Easy Setup Wizard will appear and perform WAN auto detection for the type of Internet connection.
Section 3 - Coniguration According to the detection result, the wizard will indicate the type of Internet connection that you’re currently use. You can configure your wireless network. Click Conigure button in Wireless Settings. Select the type of Wireless security you use (Disable Wireless Security or AUTO-WPA/WPA2) and enter the network name (SSID, Service Set Identiier) and security password. The network name(SSID) is the name of your wireless network. Create a name using up to 32 characters.
Section 3 - Coniguration In the inal stage of Easy setup wizard, the summary will show your current coniguration. Click Save to complete the setting. When the internet connectivity is established, the webpage will be redirected to D-Link Website.
Section 3 - Coniguration Manual Coniguration Dynamic (Cable) If you opt to set up your Internet connection manually, you will be redirected to a WAN page that allows you to select your Internet type and enter the correct coniguration parameters. Select your Internet connection type using the “My Internet Connection is” drop-down menu. Click the Save Settings button when you have conigured the connection.
Section 3 - Coniguration Dynamic IP Address (DHCP) Select Dynamic IP (DHCP) to obtain IP Address information Connection: automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for Cable modem services. Host Name: The Host Name is optional but may be required by some ISPs. Enter the Primary DNS server IP address assigned by your ISP.
Section 3 - Coniguration PPPoE (DSL) Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. Select PPPoE (Username/Password) from the dropConnection: down menu.
Section 3 - Coniguration Static IP Address Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the ields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
Section 3 - Coniguration Wireless Settings If you want to conigure the wireless settings on your router using the wizard, click Wireless Connection Setup Wizard and refer to page 51. If you want to manually conigure the wireless settings on your router click Manual Wireless Network Setup and refer to the next page.
Section 3 - Coniguration Manual Wireless Network Setup '()*+, -./,+,001 Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Click Add New to create your own time schedule to enable the wireless function. Wireless Network Service Set Identiier (SSID) is the name of your Name: wireless network. Create a name using up to 32 characters. The SSID is case-sensitive. 802.11 Mode: Select one of the following: Mixed 802.
Section 3 - Coniguration Transmission Select the transmit rate. It is strongly suggested to select Best (Auto) for best performance. Rate: 234567 89::73 Enabling Hidden Mode is another way to secure your network. With this option enabled, no wireless clients will Wireless: be able to see your wireless network when they perform a scan to see what’s available. In order for your wireless devices to connect to your router, you will need to manually enter the Wireless Network Name on each device.
Section 3 - Coniguration Network Settings This section will allow you to change the local network settings of the router and to conigure the DHCP settings. ;< =>>?@AAB Enter the IP address of the router. The default IP address is 192.168.0.1. If you change the IP address, once you click Save Settings, you will need to enter the new IP address in your browser to get back into the coniguration utility. Subnet Mask: Enter the Subnet Mask. The default subnet mask is 255.255.255.0.
Section 3 - Coniguration DHCP Server Settings DHCP stands for Dynamic Host Control Protocol. The DIR-600 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DIR-600.
Section 3 - Coniguration DHCP Reservation If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range. MNOPQRST UVOSW Enter the computer name or select from the drop-down menu and click <<. IP Address: Enter the IP address you want to assign to the computer or device.
Section 3 - Coniguration Virtual Server The DIR-600 can be conigured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DIR-600 irewall feature ilters out unrecognized packets to protect your LAN network so all computers networked with the DIR-600 are invisible to the outside world.
Section 3 - Coniguration This will allow you to open a single port. If you would like to open a range of ports, refer to the next page. XYZ[\ Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the ields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Coniguration Port Forwarding This will allow you to open a single port or a range of ports. ]^_`a Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the ields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Coniguration Trafic Control Use this section to conigure D-Link’s Smart Trafic Control. The Trafic Control improves your online gaming experience by ensuring that your game trafic is prioritized over other network trafic, such as FTP or Web. bcdefg hidjkl Select this function to control the access bandwidth Control: of computer in LAN. Auto Bandwidth All the computers in LAN will be distributed the Equal: bandwidth equally.
Section 3 - Coniguration Network Filters Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the Network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the Broadband Router. mnopqrst uvm Select Turn MAC Filtering Off, allow MAC addresses listed Filtering: below, or deny MAC addresses listed below from the drop-down menu.
Section 3 - Coniguration Website Filters Website Filters are used to allow you to set up a list of allowed Web sites that can be used by multiple users through the network. To use this feature select to Allow or Deny, enter the domain or website and click Add, and then click Save Settings. You must also select Apply Web Filter under the Access Control section (page 40). wxyz{|}~ ~~ Filter Below: Select Deny or Allow computers access to only these sites.
Section 3 - Coniguration Firewall Settings A irewall protects your network from the outside world. The D-Link DIR-600 offers a irewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
Section 3 - Coniguration Advanced Wireless Settings Set the transmit power of the antennas. Beacon Period: Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. RTS Threshold: This value should remain at its default setting of 2346. If inconsistent data low is a problem, only a minor modiication should be made.
Section 3 - Coniguration Advanced Network Settings ¡ ¢£¤¤¥¡¦§¨ To use the Universal Plug and Play (UPnP™) feature click on Enabled. UPNP provides compatibility with networking equipment, software and peripherals. Enable WAN Ping Unchecking the box will not allow the DIR-600 to respond Response: to pings. Blocking the Ping may provide some extra security from hackers. Check the box to allow the Internet port to be “pinged”.
Section 3 - Coniguration Administrator Settings This page will allow you to change the Administrator and User passwords. You can also enable Remote Management. There are two accounts that can access the management interface through the web browser. The accounts are admin and user. Admin has read/write access while user has read-only access. User can only view the settings but cannot make any changes. Only the admin account has the ability to change both admin and user account passwords.
Section 3 - Coniguration Time Settings The Time Coniguration option allows you to conigure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be conigured to automatically adjust the time when needed. µ¶·¸ ¹º»¸¼ Select the Time Zone from the drop-down menu.
Section 3 - Coniguration E-mail Settings The Email feature can be used to send the system log iles, router alert messages, and irmware update notiication to your e-mail address. ½¾¿À ÁÀÂÃÄ This e-mail address will appear as the sender when Address: you receive a log ile or irmware upgrade notiication via e-mail. To Email Address: Enter the e-mail address where you want the e-mail sent. SMTP Server Enter the SMTP server address for sending Address: e-mail.
Section 3 - Coniguration System Settings ÅÆÇÈ ÅÈÉÉÊËÌÍ ÉÎ Use this option to save the current router coniguration Local Hard Drive: settings to a ile on the hard disk of the computer you are using. First, click the Save button. You will then see a ile dialog, where you can select a location and ile name for the settings. Load Settings Use this option to load previously saved router from Local Hard coniguration settings.
Section 3 - Coniguration Update Firmware You can upgrade the irmware of the Router here. Make sure the irmware you want to use is on the local hard drive of the computer. Click on Browse to locate the irmware ile to be used for the update. Please check the D-Link support site for irmware updates at http://support.dlink.com. You can download irmware upgrades to your hard drive from the D-Link support site. ÏÐÑÒÓÔÑÕ Information: Displays the current firmware version and date.
Section 3 - Coniguration DDNS The DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.
Section 3 - Coniguration System Check The System Check feature allows you to verify the physical connectivity on both LAN and Internet interface. ÚÛÜÝ Þßàáâ The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP Address that you wish to Ping, and click Ping. Ping Results: The results of your ping attempts will be displayed here.
Section 3 - Coniguration Device Information This page displays the current information for the DIR-600. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed.
Section 3 - Coniguration Log The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the router logs. You can deine what types of events you want to view and the level of the events to view.
Section 3 - Coniguration Stats The screen below displays the Trafic Statistics. Here you can view the amount of packets that pass through the DIR-600 on both the Internet and the LAN ports. The trafic counter will reset if the device is rebooted.
Section 3 - Coniguration Internet Sessions The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WANside computer. ôõ ö÷÷øùúúû The IP address and, where appropriate, port number of the local application. TCP Session: This shows the number of TCP packets being sent from the source IP address.
Section 3 - Coniguration Wireless The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients.
Section 3 - Coniguration Support D-Link DIR-600 User Manual 46
Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DIR-600 offers the following types of security: • WPA2 (Wi-Fi Protected Access 2) • WPA (Wi-Fi Protected Access) • WPA2-PSK(Pre-Shared Key) • WPA-PSK (Pre-Shared Key) What is WPA? WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
Section 4 - Security Wireless Connection Setup Wizard To run the security wizard, browse to the Setup page and then click the Wireless Connection Setup Wizard button.
Section 4 - Security Enter the SSID (Service Set Identiier). The SSID is the name of your wireless network. Create a name using up to 32 characters. The SSID is case-sensitive. If you would like the router to automatically assign a network key to your network, you can click the button- “automatically assign a network key”. Click Next to continue. Or if you would like to create the key by your own, please click the button- “ Manual assign a Network key” and click Next to continue.
Section 4 - Security Click Save to inish the Security Wizard.
Section 4 - Security Conigure WPA-Personal (PSK) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based coniguration by opening a web browser and entering the IP address of the router (192.168.0.1).
Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows 7 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before coniguring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). Wireless Icon 2. The utility will display any available wireless networks in your area.
Section 5 - Connecting to a Wireless Network 3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. 4. The following window appears while your computer tries to connect to the router.
Section 5 - Connecting to a Wireless Network 5. Enter the same security key or passphrase that is on your router and click Connect. You can also connect by pushing the WPS button on the router. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 5 - Connecting to a Wireless Network Using Windows® XP Windows® XP users may use the built-in wireless utility (Zero Coniguration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Section 5 - Connecting to a Wireless Network Conigure WPA-PSK It is recommended to enable WEP on your wireless router or access point before coniguring your wireless adapter. If you are joining an existing network, you will need to know the WEP key being used. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router.
Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DIR-600. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different operating system, the screen shots on your computer will look similar to the following examples.) 1. Why can’t I access the web-based coniguration utility? When entering the IP address of the D-Link router (192.168.0.
Section 6 - Troubleshooting • Conigure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Section 6 - Troubleshooting 3. Why can’t I connect to certain sites or send and receive e-mails when connecting through my router? If you are having a problem sending or receiving e-mail, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To ind the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to.
Section 6 - Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you ind your MTU, you can now conigure your router with the proper MTU size.
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Appendix A - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or ofice network. Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford.
Appendix A - Wireless Basics Wireless Personal Area Network (WPAN) Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to 30 feet away. Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other devices that operate on batteries.
Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere not just at home or ofice. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Appendix A - Wireless Basics Security Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up. Wireless Modes There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router.
Appendix B - Networking Basics Networking Basics Check your IP address After you install your adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows Vista® users type in the Start Search box.) At the prompt, type ipconig and press Enter.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows Vista® Windows® XP Windows® 2000 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections. Click on Start > Control Panel > Network Connections. From the desktop, right-click My Network Places > Properties.
Appendix C - Technical Speciications Technical Speciications Standards • IEEE 802.11n • IEEE 802.11g • IEEE 802.11b • IEEE 802.3 • IEEE 802.3u • IEEE 802.3x LEDs Security • 64/128-bit WEP • WPA-Personal • WPA2-Personal Operating Humidity • 10%-90% non-condensing Wireless Signal Rates* • 150Mbps • 48Mbps • 54Mbps • 24Mbps • 36Mbps • 12Mbps • 18Mbps • 9Mbps • 11Mbps • 5.5Mbps • 6Mbps • 1Mbps • 2Mbps Frequency Range • 2.4GHz to 2.
Appendix D - Contacting Technical Support Copyright ©2010 by D-Link Corporation/D-Link Systems, Inc. All rights reserved. CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
