User Manual DIR-320NRU Multifunction Wireless Router Supporting WiMAX, 3G GSM/CDMA with Built-in Switch May 2012
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting User Manual Contents Chapter 1. Introduction..........................................5 Contents and Audience.......................................................5 Conventions.................................................................5 Document Structure..........................................................5 Chapter 2. Overview..............................................6 General Information........
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting User Manual Net........................................................................73 WAN......................................................................73 Creating 3G WAN Connection.............................................74 Creating PPPoE WAN Connection..........................................77 Creating Static IP WAN Connection......................................
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting User Manual System....................................................................144 Administrator Password..................................................144 Configuration...........................................................145 System Log..............................................................146 Firmware Upgrade........................................................148 NTP Client.............
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Introduction User Manual CHAPTER 1. INTRODUCTION Contents and Audience This manual describes the router DIR-320NRU and explains how to configure and operate it. This manual is intended for users familiar with basic networking concepts, who create an in-home local area network, and system administrators, who install and configure networks in offices.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Overview User Manual CHAPTER 2. OVERVIEW General Information The DIR-320NRU device is a multifunction wireless router supporting WiMAX, 3G GSM and CDMA with a built-in switch. It provides a fast and simple way to create a wireless and wired network at home or in an office. The router is equipped with a USB port for connecting a USB modem1, which can be used to establish connection to the Internet.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Overview User Manual Specifications* WAN Interface: • 1 10/100BASE-TX Ethernet port for cable or DSL modem or private Ethernet line. LAN Interface: • 4 10/100BASE-TX Ethernet ports. WLAN Interface: • IEEE 802.11b/g/n. USB Interface: • USB 2.0 type A port for USB modem.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Overview User Manual USB Modem2: • Auto connection to available type of supported network (3G/2G) • Enabling/disabling PIN code check, changing PIN code.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Overview User Manual Transmitter Output Power: • 802.11b: ◦ typical 17dBm (+/-2dB) at 11, 5.5, 2, and 1Mbps at 25 °C • 802.11g: ◦ typical 17dBm (+/-2dB) at 6 to 36Mbps at 25 °C ◦ typical 16dBm (+/-2dB) at 48Mbps at 25 °C ◦ typical 15dBm (+/-2dB) at 54Mbps at 25 °C • 802.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Overview User Manual • 802.11g (typical at PER = 10% (1000-byte PDUs) at room temperature): ◦ –84dBm at 6Mbps ◦ –82dBm at 9Mbps ◦ –80dBm at 12Mbps ◦ –78dBm at 18Mbps ◦ –77dBm at 24Mbps ◦ –74dBm at 36Mbps ◦ –70dBm at 48Mbps ◦ –68dBm at 54Mbps • 802.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Overview User Manual Firewall Functions: • Network Address Translation (NAT) • Stateful Packet Inspection (SPI) • IP filters • URL filter • MAC filter • DMZ • Prevention of ARP and DDoS attacks • Virtual servers.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Overview User Manual Operating Humidity: • from 10% to 90% non-condensing. Storage Humidity: • from 5% to 95% non-condensing.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Overview User Manual Product Appearance Front Panel and Right Side Panel Figure 1. Front panel view. LED Power Internet WLAN Mode Solid green The router is powered on. No light The router is powered off. Solid green The Internet connection is on. Blinking green The WAN interface is active (upstream or downstream traffic). Solid green The router's WLAN is on.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Overview User Manual Back Panel Figure 2. Back panel view. Port LAN 1-4 INTERNET USB 5V=2A Description 4 Ethernet ports to connect computers or network devices. A port to connect to a cable or DSL modem or to a private Ethernet line (it is recommended to use the cable included in the delivery package). A port for USB modem. Power connector. A button to restore the factory default settings.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Overview User Manual Delivery Package The following should be included: • Wireless router DIR-320NRU • Power adapter 5V/2A • Ethernet cable (CAT 5E) • CD-ROM with “User Manual” and “Quick Installation Guide” • “Quick Installation Guide” (brochure). ! Using a power supply with a different voltage rating than the one included will cause damage and void the warranty for this product.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual CHAPTER 3. INSTALLATION AND CONNECTION Before You Begin Please, read this manual prior to installing the device. Make sure that you have all the necessary information and equipment.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual USB Modem To connect to a WiMAX, 3G GSM or CDMA network, you should use a USB modem. Connect it to the USB port of the router, then access the web-based interface of the router, and you will be able to configure a connection to the Internet3. WiMAX USB modem ! Some WiMAX operators require subscribers to activate their WiMAX USB modems prior to using them.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual Connecting to PC PC with Ethernet Adapter 1. Make sure that your PC is powered off. 2. Connect an Ethernet cable between any of LAN ports located on the back panel of the router and the Ethernet port of your PC. 3. To connect via a WiMAX, 3G GSM or CDMA network: connect your USB modem to the USB port4 located on the back panel of the router.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual 3. In the Local Area Connection Properties window, on the General tab, select the Internet Protocol (TCP/IP) line. Click the Properties button. Figure 4. The Local Area Connection Properties window.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual 4. Select the Obtain an IP address automatically and Obtain DNS server address automatically radio buttons. Click the OK button. Figure 5. The Internet Protocol (TCP/IP) Properties window. 5. Click the ОК button in the connection properties window. Now your computer is configured to obtain an IP address automatically.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual Obtaining IP Address Automatically in OS Windows 7 1. Click the Start button and proceed to the Control Panel window. 2. Select the Network and Sharing Center section.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual 3. In the menu located on the left part of the window, select the Change adapter settings line. Figure 7. The Network and Sharing Center window.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual 4. In the opened window, right-click the relevant Local Area Connection icon and select the Properties line in the menu displayed. Figure 8. The Network Connections window.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual 5. In the Local Area Connection Properties window, on the Networking tab, select the Internet Protocol Version 4 (TCP/IPv4) line. Click the Properties button. Figure 9. The Local Area Connection Properties window.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual 6. Select the Obtain an IP address automatically and Obtain DNS server address automatically radio buttons. Click the OK button. Figure 10. The Internet Protocol Version 4 (TCP/IPv4) Properties window. 7. Click the OK button in the connection properties window. Now your computer is configured to obtain an IP address automatically.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual PC with Wi-Fi Adapter 1. To connect via a WiMAX, 3G GSM or CDMA network: connect your USB modem to the USB port5 located on the back panel of the router. ! If you need to connect or change a USB modem to another one when the router is powered on, power off the device, connect the modem to the USB port, and power on the router. 2.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual Configuring Wi-Fi Adapter in OS Windows XP 1. Click the Start button and proceed to the Control Panel > Network and Internet Connections > Network Connections window. 2. Select the icon of the wireless network connection and make sure that your Wi-Fi adapter is on. Figure 11. The Network Connections window. 3. Search for available wireless networks. 4.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual Configuring Wi-Fi Adapter in OS Windows 7 1. Click the Start button and proceed to the Control Panel window. 2. Select the Network and Sharing Center section.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual 6. In the opened window, in the list of available wireless networks, select the wireless network DIR-320NRU and click the Connect button. Figure 14. The list of available networks. 7. Wait for about 20-30 seconds. After the connection is established, the network icon will be displayed as the signal level scale.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual Connecting to Web-based Interface When you have configured your computer, you can access the web-based interface and configure needed parameters (create a WAN connection, change the parameters of the wireless network, specify the settings of the firewall, etc.). 1. Start a web browser (see the Before You Begin section, page 16). 2.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual Figure 17. The page for changing the default administrator password. Enter the new password in the Password and Confirmation fields. Then click the Save button. ! Remember or write down the new password for the administrator account.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual To configure the router's wireless network, click the Configure Wi-Fi button. After clicking the button, the Wi-Fi Setup Wizard opens (see the Wi-Fi Setup Wizard section, page 62). To configure the router to use an IPTV set-top box, click the Configure IPTV button. After clicking the button, the IPTV Setup Wizard opens (see the IPTV Setup Wizard section, page 68).
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual To configure the router's WLAN parameters, left-click the SSID of the WLAN (the right column of the SSID line). After clicking the line, the Wi-Fi / Basic settings page opens (see the Basic Settings section, page 99). The web-based interface of the router is multilingual. Select a needed language from the menu displayed when the mouse pointer is over the Language caption.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual Saving and Restoring Settings ! Note that you should regularly save the changes of the router's settings to the nonvolatile memory. The router's web-based interface displays the notification on unsaved changes at the top of the page. Figure 21. The notification on unsaved changes.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Installation and Connection User Manual 1. Power off the device. 2. Insert a small paperclip into the hole of the RESET button and push. 3. Power on the device keeping the button pushed. 4. After 5 seconds, release the button. ! When you keep the button pushed for more than 8 seconds, the router switches to crash recovery mode.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual CHAPTER 4. CONFIGURING INTERFACE VIA WEB-BASED Setup Wizards Internet Setup Wizard To configure connection to the Internet, click the Connect to internet button. Figure 23. Configuring connection to the Internet. By default, the WAN connection is configured in the system.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Figure 25. The page for selecting the connection type. On the opened page, select the needed choice of the radio button and click the Next button. To create a WiMAX WAN connection, on the opened page, select the USB-WiMAX choice and click the Next button (the page is displayed only when a WiMAX USB modem is connected to the router).
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual PPPoE Connection Figure 26. Configuring PPPoE WAN connection. In the Name field, specify a name for the connection for easier identification and click the Next button. Figure 27. Configuring PPPoE WAN connection. If needed, in the MTU field, change the maximum size of units transmitted by the interface.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Also you can set the address of a device connected to the router's LAN at the moment. To do this, select the relevant value from the drop-down list located to the right of the field (the field will be filled in automatically). In the Username field, enter your login, and in the Password and Password confirmation fields – the password provided by your ISP.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description Keep Alive Select the checkbox if you want the router to keep you connected to your ISP even when the connection has been inactive for a specified period of time. When the checkbox is selected, the LCP interval and LCP fails fields are available. Specify the required values.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual If needed, change the connection settings available in the Miscellaneous section. Figure 29. Configuring PPPoE WAN connection. Parameter Enable RIP Description Select the checkbox to allow using RIP for this connection. Enable IGMP Multicast Select the checkbox to allow multicast traffic from the external network (e.g. video streaming) to be received.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Static IP Connection Figure 30. Configuring Static IP WAN connection. In the Name field, specify a name for the connection for easier identification and click the Next button. Figure 31. Configuring Static IP WAN connection. If needed, in the MTU field, change the maximum size of units transmitted by the interface.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Also you can set the address of a device connected to the router's LAN at the moment. To do this, select the relevant value from the drop-down list located to the right of the field (the field will be filled in automatically). Fill in the IP address and Netmask fields. In the Gateway IP address field, enter the IP address of the gateway used by this WAN connection.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual If needed, change the connection settings available in the Miscellaneous section. Figure 33. Configuring Static IP WAN connection. Parameter Enable RIP Description Select the checkbox to allow using RIP for this connection. Enable IGMP Multicast Select the checkbox to allow multicast traffic from the external network (e.g. video streaming) to be received.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Dynamic IP Connection Figure 34. Configuring Dynamic IP WAN connection. In the Name field, specify a name for the connection for easier identification and click the Next button. Figure 35. Configuring Dynamic IP WAN connection. If needed, in the MTU field, change the maximum size of units transmitted by the interface.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual If your ISP has provided the addresses of the DNS servers, deselect the Obtain DNS server addresses automatically checkbox and fill in the Primary DNS server and Secondary DNS server fields. If your ISP has provided its identifier, fill in the Vendor ID field. Click the Next button to continue.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual PPTP + Static IP or L2TP + Static IP Connection Figure 37. Configuring PPTP + Static IP WAN connection. In the Name field, specify a name for the connection for easier identification and click the Next button. Figure 38. Configuring PPTP + Static IP WAN connection. If needed, in the MTU field, change the maximum size of units transmitted by the interface.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Also you can set the address of a device connected to the router's LAN at the moment. To do this, select the relevant value from the drop-down list located to the right of the field (the field will be filled in automatically). Fill in the IP address and Netmask fields. In the Gateway IP address field, enter the IP address of the gateway used by this WAN connection.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual If needed, change the connection settings available in the Miscellaneous section. Figure 40. Configuring PPTP + Static IP WAN connection. Parameter Enable RIP Description Select the checkbox to allow using RIP for this connection. Enable IGMP Multicast Select the checkbox to allow multicast traffic from the external network (e.g. video streaming) to be received.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Figure 41. Configuring PPTP + Static IP WAN connection. Leave the Connect automatically checkbox selected to allow automatic start of the connection upon the load of the router. In the Username field, enter your login, and in the Password and Password confirmation fields – the password provided by your ISP.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual If needed, specify additional settings for your PPTP + Static IP or L2TP + Static IP WAN connection. Parameter Description Select a method of MPPE encryption. Encryption • No encrypt: MPPE encryption is not applied. • MPPE 40/128 bit: MPPE encryption with a 40-bit or 128-bit key is applied. • MPPE 40 bit: MPPE encryption with a 40-bit key is applied.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual If needed, change the settings of the VPN tunnel available in the Miscellaneous section. Figure 42. Configuring PPTP + Static IP WAN connection. Parameter Enable RIP Description Select the checkbox to allow using RIP for this connection. NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual PPTP + Dynamic IP or L2TP + Dynamic IP Connection Figure 43. Configuring PPTP + Dynamic IP WAN connection. In the Name field, specify a name for the connection for easier identification and click the Next button. Figure 44. Configuring PPTP + Dynamic IP WAN connection. If needed, in the MTU field, change the maximum size of units transmitted by the interface.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual If your ISP has provided the addresses of the DNS servers, deselect the Obtain DNS server addresses automatically checkbox and fill in the Primary DNS server and Secondary DNS server fields. If your ISP has provided its identifier, fill in the Vendor ID field. Click the Next button to continue.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Figure 46. Configuring PPTP + Dynamic IP WAN connection. Leave the Connect automatically checkbox selected to allow automatic start of the connection upon the load of the router. In the Username field, enter your login, and in the Password and Password confirmation fields – the password provided by your ISP.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual If needed, specify additional settings for your PPTP + Dynamic IP or L2TP + Dynamic IP WAN connection. Parameter Description Select a method of MPPE encryption. Encryption • No encrypt: MPPE encryption is not applied. • MPPE 40/128 bit: MPPE encryption with a 40-bit or 128-bit key is applied. • MPPE 40 bit: MPPE encryption with a 40-bit key is applied.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual If needed, change the settings of the VPN tunnel available in the Miscellaneous section. Figure 47. Configuring PPTP + Dynamic IP WAN connection. Parameter Enable RIP Description Select the checkbox to allow using RIP for this connection. NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual 3G Connection Figure 48. Configuring 3G connection. In the Name field, specify a name for the connection for easier identification and click the Next button. Figure 49. Configuring 3G connection.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual In the Mode drop-down list, leave the auto value in order to let the router connect automatically to an available type of network, or select a needed value from the drop-down list. For GSM USB modems only. In the Username field, enter your login, and in the Password and Password confirmation fields – the password provided by your 3G operator.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual If needed, change the connection settings available in the Miscellaneous section. Figure 50. Configuring 3G connection. Parameter Description NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN. Firewall Select the checkbox to enable protection against ARP and DDoS attacks. Click the Next button to continue.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Site Setup Wizard To create a virtual server for redirecting incoming Internet traffic to a specified IP address in the LAN, click the Host site button. Figure 51. The page for adding a virtual server. On the opened page, you can specify the following parameters: Parameter Description Name Enter a name for the virtual server for easier identification.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Wi-Fi Setup Wizard To specify all needed settings for your wireless network, click the Configure Wi-Fi button. Figure 52. Common and advanced settings of the wireless LAN. On the opened page, in the Common settings section, select the Enable Wireless checkbox (if it was deselected before) to enable Wi-Fi connections.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Click the Next button to continue. On the next page, you can modify security settings of the WLAN. By default, the Open network authentication type with no encryption is specified for the WLAN. Figure 54. The default security settings. ! The default security settings do not provide sufficient protection for the WLAN.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Authentication type Description WEPAUTO A mixed type of authentication. When this value is selected, devices using the Open authentication type with enabled WEP encryption and devices using the Shared authentication type can connect to the router's WLAN.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual When the Open, Shared, or WEPAUTO value is selected, the WEP Encryption settings section is displayed (the section is unavailable for the wireless network operating modes which support the standard 802.11n): Figure 56. The Open value is selected from the Network Authentication drop-down list. Parameter Description The checkbox activating WEP encryption.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual When the WPA-PSK, WPA2-PSK, or WPA-PSK/WPA2-PSK mixed value is selected, the WPA Encryption settings section is displayed: Figure 57. The WPA2-PSK value is selected from the Network Authentication drop-down list. Parameter Description Encryption Key PSK A key for WPA encryption. The key can contain digits and/or Latin characters.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual When the WPA, WPA2, or WPA/WPA2 mixed value is selected, the RADIUS settings and WPA Encryption settings sections are available: Figure 58. The WPA2 value is selected from the Network Authentication drop-down list.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual IPTV Setup Wizard To configure the router to use an IPTV set-top box, click the Configure IPTV button. Figure 59. The page for selecting a LAN port to connect an IPTV set-top box. On the opened page, select the LAN port of the router to which you will connect your IPTV set-top box and click the Change button. After that you will get to the quick settings page.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Status The pages of this section display data on the current state of the router: • network statistics • IP addresses leased by the DHCP server • the routing table • data on devices connected to the router's network and its web-based interface.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual DHCP The Status / DHCP page displays the information on computers that have been identified by hostnames and MAC addresses and have got IP addresses from the DHCP server of the device, as well as the IP address expiration periods (the lease time). Figure 61. The Status / DHCP page.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Routing Table The Status / Routing table page displays the information on routes. The table contains destination IP addresses, gateways, subnet masks, and other data. Figure 62. The Status / Routing table page.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual LAN Clients On the Status / LAN clients page, you can view the list of devices connected to the router and devices accessing its web-based interface. Figure 63. The Status / LAN clients page. For each device the following data are displayed: the IP address, the MAC address, and the interface to which the device is connected.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Net In this menu you can configure basic parameters of the router's local area network and configure connection to the Internet (a WAN connection). WAN On the Net / WAN page, you can create and edit connections used by the router. By default, the WAN connection is configured in the system. It is assigned to the INTERNET port of the router.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Creating 3G WAN Connection If the PIN code check is enabled for the SIM card inserted into your USB modem, then prior to creating a 3G WAN connection, proceed to the USB modem menu and enter the PIN code on the page displayed (see the USB Modem section, page 137).
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Figure 66. The page for creating a new connection. The PPP and Miscellaneous sections. Parameter Description PPP Username Without authorization Password Password confirmation APN A username (login) to connect to the network of the operator. Select the checkbox if your operator does not require authorization. A password to connect to the network of the operator.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description Extra options In the field, you can specify additional data for encryption or authentication. Optional. Dial on demand Select the checkbox if you want the router to establish connection to the Internet on demand. In the Maximum idle time field, specify a period of inactivity (in seconds) after which the connection should be terminated.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Creating PPPoE WAN Connection To create a connection of this type, click the Add button on the Net / WAN page. On the opened page, select the PPPoE value from the Connection Type drop-down list and specify the needed values. Figure 67. The page for creating a new connection. The General settings and Ethernet sections.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description PPP Username Without authorization Password Password confirmation A username (login) to access the Internet. Select the checkbox if you don't need to enter a username and password to access the Internet. A password to access the Internet. The confirmation of the entered password (to avoid mistypes).
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description Enable IGMP Multicast Select the checkbox to allow multicast traffic from the external network (e.g. video streaming) to be received. NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN. Firewall Select the checkbox to enable protection against ARP and DDoS attacks.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Creating Static IP WAN Connection To create a connection of the Static IP type, click the Add button on the Net / WAN page. On the opened page, select the Static IP value from the Connection Type drop-down list and specify the needed values. Figure 69. The page for creating a new connection. The General settings and Ethernet sections.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description Enable IGMP Multicast Select the checkbox to allow multicast traffic from the external network (e.g. video streaming) to be received. NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN. Firewall Select the checkbox to enable protection against ARP and DDoS attacks.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Creating Dynamic IP WAN Connection To create a connection of the Dynamic IP type, click the Add button on the Net / WAN page. On the opened page, select the Dynamic IP value from the Connection Type drop-down list and specify the needed values. Figure 71. The page for creating a new connection. The General settings and Ethernet sections.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN. Firewall Select the checkbox to enable protection against ARP and DDoS attacks. When all needed settings are configured, click the Save button.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Creating PPTP + Static IP or L2TP + Static IP WAN Connection To create a connection of the PPTP + Static IP or L2TP + Static IP type, click the Add button on the Net / WAN page. On the opened page, select the relevant value from the Connection Type dropdown list and specify the needed values. Figure 73. The page for creating a new connection.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description Enable IGMP Multicast Select the checkbox to allow multicast traffic from the external network (e.g. video streaming) to be received. NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN. Firewall Select the checkbox to enable protection against ARP and DDoS attacks. Figure 75.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description VPN Connect automatically Username Without authorization Password Password confirmation VPN server address Select the checkbox to enable auto-start of the connection upon the boot-up of the router. A username (login) to access the Internet. Select the checkbox if you don't need to enter a username and password to access the Internet.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description PPP debug Select the checkbox if you want to log all data on PPP connection debugging. IP received The IP address assigned by the ISP. Miscellaneous Enable RIP Select the checkbox to allow using RIP for this connection. NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Creating PPTP + Dynamic IP or L2TP + Dynamic IP WAN Connection To create a connection of the PPTP + Dynamic IP or L2TP + Dynamic IP type, click the Add button on the Net / WAN page. On the opened page, select the relevant value from the Connection Type drop-down list and specify the needed values. Figure 76. The page for creating a new connection.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description A MAC address assigned to the interface. This parameter is mandatory if your ISP uses MAC address binding. In the field, enter the MAC address registered by your ISP upon concluding the agreement.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description NAT Select the checkbox if you want one WAN IP address to be used for all computers of your LAN. Firewall Select the checkbox to enable protection against ARP and DDoS attacks. Figure 78. The page for creating a new connection. The VPN and Miscellaneous sections.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description Select a method of MPPE encryption. Encryption • No encrypt: MPPE encryption is not applied. • MPPE 40/128 bit: MPPE encryption with a 40-bit or 128-bit key is applied. • MPPE 40 bit: MPPE encryption with a 40-bit key is applied. • MPPE 128 bit: MPPE encryption with a 128-bit key is applied.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual LAN To configure the router's local interface, proceed to the Net / LAN page. Figure 79. The page for configuring the local interface. If needed, edit the basic parameters of the local interface. Parameter Description IP Address The IP address of the router in the local subnet. By default, the following value is specified: 192.168.0.1.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Existing MAC-IP pairs are displayed in the table of the Static DHCP section. To remove a pair, select the relevant line in the table and click the Remove button. Then click the Save button. In the DHCP server section, you can configure the built-in DHCP sever of the router. Parameter Description An operating mode of the router's DHCP server.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Wi-Fi In this menu you can specify all needed settings for your wireless network. Common settings On the Wi-Fi / Common settings page, you can enable your wireless local area network (WLAN) and split it into parts. Figure 80. Common settings of the wireless LAN. The Enable Wireless checkbox enables Wi-Fi connections. By default, the checkbox is selected.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Basic Settings On the Wi-Fi / Basic settings page, you can configure basic parameters of the device's WLAN. Figure 81. Basic settings of the wireless LAN. Parameter Description Hide Access Point If the checkbox is selected, other users cannot see your Wi-Fi network.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Security Settings On the Wi-Fi / Security settings page, you can modify security settings of the WLAN. Figure 82. The default security settings. By default, the Open network authentication type with no encryption is specified for the WLAN. ! The default security settings do not provide sufficient protection for the WLAN.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Authentication type Description WEPAUTO A mixed type of authentication. When this value is selected, devices using the Open authentication type with enabled WEP encryption and devices using the Shared authentication type can connect to the router's WLAN.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual When the Open, Shared, or WEPAUTO value is selected, the WEP Encryption settings section is displayed (the section is unavailable for the wireless network operating modes which support the standard 802.11n): Figure 84. The Open value is selected from the Network Authentication drop-down list. Parameter Description The checkbox activating WEP encryption.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual When the WPA-PSK, WPA2-PSK, or WPA-PSK/WPA2-PSK mixed value is selected, the WPA Encryption settings section is displayed: Figure 85. The WPA2-PSK value is selected from the Network Authentication drop-down list. Parameter Description Encryption Key PSK A key for WPA encryption. The key can contain digits and/or Latin characters.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual When the WPA, WPA2, or WPA/WPA2 mixed value is selected, the RADIUS settings and WPA Encryption settings sections are available: Figure 86. The WPA2 value is selected from the Network Authentication drop-down list.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual MAC Filter On the Wi-Fi / MAC Filter page, you can define a set of MAC addresses of devices which will be allowed to access the WLAN, or define MAC addresses of devices which will not be allowed to access the WLAN. Figure 87. The MAC filter for the wireless network.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Figure 88. The tab for adding a MAC address. Enter an address in the MAC address field of the MAC address adding section and click the Add button.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Station List On the Wi-Fi / Station List page, you can view the list of wireless clients connected to the router. Figure 89. The list of the wireless clients. If you want to disconnect a wireless device from your WLAN, select the checkbox in the line containing the relevant MAC address, and click the Disconnect button.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual WPS On the Wi-Fi / WPS page, you can enable the function for secure configuration of the WLAN and select a method used to easily add wireless devices to the WLAN. The WPS function helps to configure the protected wireless network automatically. Devices connecting to the wireless network via the WPS function must support the WPS function.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual To activate the WPS function, select the WPS Enable checkbox and click the Change button. When the checkbox is selected, the Information and Connection sections are available on the page. Parameter Description Default PIN code The PIN code of the router. This parameter is used when connecting the router to a registrar to set the parameters of the WPS function.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Using WPS Function via Web-based Interface To add a wireless device via the PIN method of the WPS function, follow the next steps: 1. Select the WPS Enable checkbox. 2. Click the Change button. 3. Select the PIN value from the WPS Method drop-down list. 4. Select the PIN method in the software of the wireless device that you want to connect to the router's WLAN. 5.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Later you will be able to add wireless devices to the WLAN by pressing the WPS button of the router. 1. Select the PBC method in the software of the wireless device that you want to connect to the router's WLAN. 2. Click the relevant button in the software or press the WPS button on the cover of the wireless device that you want to connect to the WLAN. 3.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Additional Settings On the Wi-Fi / Additional settings page, you can define additional parameters for the WLAN of the router. ! Changing parameters presented on this page may negatively affect your WLAN! Figure 91. Additional settings of the WLAN.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description The 802.11b and 802.11g protection function is used to minimize collisions between devices of your wireless network. Select a value from the drop-down list.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual WMM On the Wi-Fi / WMM page, you can enable the Wi-Fi Multimedia function. The WMM function implements the QoS features for Wi-Fi networks. It helps to improve the quality of data transfer over Wi-Fi networks by prioritizing different types of traffic. To enable the function, select the WMM checkbox and click the Change button. Figure 92.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual For every Access Category the following fields are available: Parameter Description Aifsn Arbitrary Inter-Frame Space Number. This parameter influences time delays for the relevant Access Category. The lower the value, the higher is the Access Category priority. CWMin/CWMax Contention Window Minimum/Contention Window Maximum.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Client On the Wi-Fi / Client page, you can configure the router as a client to connect to a wireless access point. As a rule, the client mode is used to connect to a WISP network. All parameters specified on this page should be provided by your WISP. Figure 93. The page for configuring the client mode.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual When the Open or Shared authentication type is selected, the following fields are available: Parameter Description The checkbox activating WEP encryption. When the checkbox is selected, the Default Key ID field and four Encryption Key Enable Encryption WEP WEP fields are displayed on the page. For the Shared authentication type the checkbox is always selected.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual After configuring the device as a client, you need to create a WAN connection with relevant parameters for the WiFiClient port.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Advanced In this menu you can configure advanced settings of the router: • create groups of ports for VLANs • enable the UPnP function • configure a DDNS service • add name servers • define static routes • create rules for remote access to the web-based interface • allow the router to use IGMP.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Figure 95. The page for editing a group of ports for VLAN. You can specify the following parameters: Parameter Description Main settings Name A name for the port for easier identification. Enable Select the checkbox to allow using this group of ports. The type of the VLAN which identifier is specified in the VLAN ID field. Local.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description Ports Port From the list, select an available value (a physical port of the router, the wireless interface, or, if the wireless network is splitted into parts, a part of the wireless network) to assign it to this group. The port will be displayed in the table at the bottom of the page.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual UPnP On the Advanced / UPnP page, you can enable the UPnP function. UPnP is a set of networking protocols designed for automatic configuration of network devices. The UPnP function performs automatic configuration of the device's parameters for network applications requiring an incoming connection to the router. Figure 96. The Advanced / UPnP page.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual DDNS On the Advanced / DDNS page, you can define parameters of the DDNS service, which allows associating a domain name with dynamic IP addresses. Figure 97. The Advanced / DDNS page. To add a new DDNS service, click the Add button. Figure 98. The page for adding a DDNS service.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual You can specify the following parameters: Parameter DDNS Service Description Select a DDNS provider from the drop-down list. Host name The domain name registered at your DDNS provider. User name The username to authorize for your DDNS provider. User password The password to authorize for your DDNS provider.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual DNS On the Advanced / DNS page, you can add DNS servers to the system. Figure 99. The Advanced / DNS page. DNS servers are used to determine the IP address from the name of a server in Intranets or the Internet (as a rule, they are specified by an ISP or assigned by a network administrator). The device performs the DNS relay function, i.e.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Routing On the Advanced / Routing page, you can add static routes (routes for networks that are not connected directly to the device but are available through the interfaces of the device) into the system. Figure 100. The Advanced / Routing page. To create a new route, click the Add button. Figure 101. The page for adding a static route.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual You can specify the following parameters: Parameter Description Destination network A destination network to which this route is assigned. Destination netmask The destination network mask. Gateway An IP address through which the destination network can be accessed. The field is displayed when the value is selected from the Via Interface drop-down list.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Remote Access On the Advanced / Remote access page, you can configure access to the web-based interface of the router. By default, the access from external networks to the router is closed. If you need to allow access to the router from the external network, create relevant rules. Figure 102. The Advanced / Remote access page.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual IGMP On the Advanced / IGMP page, you can enable IGMP for the router. IGMP is used for managing multicast traffic (transferring data to a group of destinations). This protocol allows using network resources for some applications, e.g., for streaming video, more efficiently. Figure 104. The Advanced / IGMP page. To enable IGMP, select the Enabled checkbox.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Firewall In this menu you can configure the firewall of the router: • add rules for IP filtering • create virtual servers • define a DMZ • configure the MAC filter. IP Filters On the Firewall / IP filters page, you can create new rules for filtering IP packets and edit or remove existing rules. Figure 105. The Firewall / IP filters page.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual You can specify the following parameters: Parameter Description IP filter rule editing Name Protocol A name for the rule for easier identification. A protocol for network packet transmission. Select a value from the drop-down list. Select an action for the rule. Action ACCEPT: Allows packet transmission in accordance with the criteria specified by the rule.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description Ports Source A port of the source IP address. You can specify one port, several ports separated by a comma, or a range of ports separated by a colon. Destination A port of the destination IP address. You can specify one port, several ports separated by a comma, or a range of ports separated by a colon. Click the Change button.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Virtual Servers On the Firewall / Virtual servers page, you can create virtual servers for redirecting incoming Internet traffic to a specified IP address in the local area network. Figure 107. The Firewall / Virtual servers page. To create a new virtual server, click the Add button. Figure 108. The page for adding a virtual server.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual You can specify the following parameters: Parameter Description Template Select a virtual server template from the drop-down list, or select Custom to specify all parameters of the new virtual server manually. Name A name for the virtual server for easier identification. You can specify any name.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual DMZ A DMZ is a host or network segment located “between” internal (local) and external (global) networks. In the router, the DMZ implements the capability to transfer a request coming to a port of the router from the external network to a specified host of the internal network. On the Firewall / DMZ page you can specify the IP address of the DMZ host. Figure 109.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual MAC Filter On the Firewall / MAC filter page, you can configure MAC-address-based filtering for computers of the router's LAN. Figure 110. The Firewall / MAC filter page. To specify a new address for the MAC filter, click the Add button. Figure 111. The page for adding an address for the MAC filter.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual USB Modem This menu is designed to operate USB modems. If the PIN code check for the SIM card inserted into your USB modem is not disabled, then upon the first access to the pages of the USB modem menu (under the current web-interface session) the page for checking the PIN code is displayed6. Enter the PIN code in the relevant field and click the Enter button.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description Mode A type of the network to which the USB modem is connected (2G or 3G). PIN On the USB modem / PIN page, you can change the PIN code of the identification card inserted into your USB modem, disable or enable the check of the PIN code. ! The operations presented on this page are not available for CDMA USB modems. Figure 113.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Figure 114. Entering the PUK code. For further use of the card, enter the PUK code in the relevant field, and then specify a new PIN code for your SIM card in the New PIN code and New PIN code confirmation fields. Click the Enter button.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual WiMAX This menu is designed to operate WiMAX USB modems. Information On the WiMAX / Information page, you can connect to the network of your WiMAX ISP to establish a high-speed wireless connection to the Internet. Figure 115. The WiMAX / Information page.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Parameter Description Connect Click the button to connect to the WiMAX network. Beforehand, you need to create a WAN connection with relevant parameters. The button is displayed when the connection is not established. Click the button to disconnect from the WiMAX network.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Control This menu is designed to create restrictions on access to certain web sites. URL Filter On the Control / URL filter page, you can specify restrictions on access to certain web sites. Figure 116. The Control / URL filter page. The Configuration tab.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Figure 117. The Control / URL filter page. The URL addresses tab. On the opened page, specify the needed parameters. Figure 118. The page for adding an address for the URL filter. Enter a URL address in the URL address field and click the Save button.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual System In this menu you can do the following: • change the password used to access the router's settings • save the current settings to the non-volatile memory • create a backup of the router's configuration • restore the router's configuration from a previously saved file • restore the factory default settings • view the system log • update the firmware
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Configuration On the System / Configuration page, you can save the changed settings to the non-volatile memory, restore the factory defaults, backup the current configuration, or restore the router's configuration from a previously created file. Figure 120. The System / Configuration page.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual System Log On the System / System log page, you can set the system log options and configure sending the system log to a remote host. Figure 121. The System / System log page. The Configuration tab. To enable logging of the system events, select the Logging checkbox on the Configuration tab. Then specify the needed parameters.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual To disable logging of the system events, deselect the Logging checkbox and click the Change button. On the Log tab, the events specified in the Logging level list are displayed. Figure 122. The System / System log page. The Log tab. To view the latest system events, click the Refresh button.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Firmware Upgrade On the System / Firmware upgrade page, you can upgrade the firmware of the router. ! Upgrade the firmware only when the router is connected to your PC via a wired connection. Figure 123. The System / Firmware upgrade page. The current version of the router's firmware is displayed in the Firmware version field on the Start page.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual NTP Client On the System / NTP client page, you can configure automatic synchronization of the system time with a time server on the Internet. Figure 124. The System / NTP client page. To enable automatic synchronization with a time server: 1. Select the Enabled checkbox. 2. Select your time zone. 3.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Ping On the System / Ping page, you can check availability of a host from the local or global network via the Ping utility. The Ping utility sends echo requests to a specified host and receives echo replies. Figure 125. The System / Ping page.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Configuring via Web-based Interface User Manual Telnet On the System / Telnet page, you can enable or disable access to the device settings via TELNET from your LAN. By default, access is disabled. Figure 126. The System / Telnet page. To enable access via TELNET, select the On checkbox.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Operation Guidelines User Manual CHAPTER 5. OPERATION GUIDELINES Supported USB Modems GSM modems: • Huawei E1550 • Huawei E160G • Huawei E169G • Huawei E171 • Huawei E173 • Huawei E220 • ZTE MF112 • ZTE MF192 • ZTE MF626 • ZTE MF627 • ZTE MF652 • ZTE MF668 • ZTE MF752. CDMA modems9: • Airplus MCD-650 • Airplus MCD-800 • AnyDATA ADU-300A • AnyDATA ADU-310A • Axesstel MV110 • Ubiquam UM-400 • WeTelecom WM-D200.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Operation Guidelines User Manual Safety Instructions Place your router on a flat horizontal surface or mount the router on the wall (the mounting holes are located on the bottom panel of the device). Make sure that the router is provided with sufficient ventilation. To prevent overheating, do not obstruct the ventilation openings of the router.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Operation Guidelines User Manual Connecting to Cable or DSL Modem If you need to connect the router to a cable or DSL modem, do the following. 1. Place the router in an open location in the supposed center of your wireless network. Do not plug the power adapter into the router. 2. Turn off your PC. 3.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Abbreviations and Acronyms User Manual CHAPTER 6.
DIR-320NRU Multifunction Wireless Router WiMAX, 3G GSM/CDMA with Built-in Switch Supporting Abbreviations and Acronyms User Manual PPPoE Point-to-point protocol over Ethernet PPTP Point-to-point tunneling protocol PSK Pre-shared key PUK PIN Unlock Key QoS Quality of Service R-UIM Removable User Identity Module RADIUS Remote Authentication in Dial-In User Service RIP Routing Information Protocol RSSI Received Signal Strength Indicator RTS Request To Send SIM Subscriber Identification
