Table of Contents Manual Overview This manual contains the following sections: Section 1 - “Product Overview” describes what is included with the DIR-130 router, and things to consider before installing (page 1). Section 2 - “Installation” describes how to install the router on your network (page 6). Section 3 - “Configuration” describes how to configure the settings on your DIR-130 router (page 10). Section 4 - “Troubleshooting” explains how to resolve common issues (page 56).
Table of Contents D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date Description 1.0 February 8, 2007 • DIR-130 Revision A1 with firmware version 1.00 1.1 September 5, 2007 • Updated for firmware version 1.
Table of Contents Table of Contents Manual Overview........................................................... i Manual Revisions..................................................... ii Trademarks............................................................... ii Product Overview......................................................... 1 Package Contents.................................................... 1 System Requirements.............................................. 2 Features.........................
Table of Contents DDNS................................................................ 46 System Check................................................... 47 Schedules......................................................... 48 Log Settings...................................................... 49 Device Information............................................ 50 Log.................................................................... 51 Statistics...........................................................
Section 1 - Product Overview Product PackageOverview Contents D-Link DIR-130 8-port VPN Router Power Adapter Ethernet Cable CD-ROM Note: Using a power supply with a different voltage rating than the one included with the DIR-130 will cause damage and void the warranty for this product.
Section 1 - Product Overview System Requirements Network Requirements • An Ethernet-based Cable or DSL modem • 10/100 Ethernet devices Computer with the following: • Windows®, Macintosh, or Linux-based operating system • An installed Ethernet adapter Web-based Configuration Utility Requirements Browser Requirements: • Internet Explorer 6.0 or higher • Mozilla 1.7.12 or higher • Firefox 1.5 or higher • Safari 1.0 or higher (with Java 1.3.1 or higher) • Flock 0.7.14 or higher • Opera 6.
Section 1 - Product Overview Features • Advanced Firewall Features - The Web-based user interface displays a number of advanced network management features including: • Parental Controls - Easily applied content filtering based on MAC Address, URL, and/or Domain Name. • Filter Scheduling - These filters can be scheduled to be active on certain days or for a duration of hours or minutes. • Secure Multiple/Concurrent Sessions - The DIR-130 can pass through VPN sessions.
Section 1 - Product Overview Hardware Overview Connections LAN Ports (1-8) Connect Ethernet devices such as computers, switches, and hubs. Reset Pressing the Reset button restores the router to its original factory default settings. Internet Port The auto MDI/MDIX Internet port is the connection for the Ethernet cable to the cable or DSL modem. Power Receptor Receptor for the supplied power adapter.
Section 1 - Product Overview Hardware Overview LEDs Status LED A blinking light indicates that the DIR-130 is ready. Power LED A solid light indicates a proper connection to the power supply. D-Link DIR-130 User Manual Local Network LEDs A solid light indicates a connection to an Ethernet-enabled computer on ports 1-8. This LED blinks during data transmission. Internet LED A solid light indicates connection on the Internet port. This LED blinks during data transmission.
Section 2 - Installation Installation This section will walk you through the installation process. Before you Begin Please configure the router with the computer that was last connected directly to your modem. Also, you can only use the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn the modem back on.
Section 2 - Installation Connect to Cable/DSL/Satellite Modem If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below: 1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Turn the power off on your modem. If there is no on/off switch, then unplug the modem’s power adapter. Shut down your computer. 3.
Section 2 - Installation Connect to Another Router If you are connecting the D-Link router to another router to use as a switch, you will have to do the following before connecting the router to your network: • Disable UPnP™ • Disable DHCP • Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address from your other router. To connect to another router, please follow the steps below: 1. Plug the power into the router.
Section 2 - Installation 6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the Internet port of the D-Link router. 8. You may now use the other 7 LAN ports to connect other Ethernet devices and computers.
Section 3 - Configuration Configuration This section will show you how to configure your new D-Link router using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1). Enter admin as the User name field and enter the password in the Password field. Leave the password blank by default.
Section 3 - Configuration Setup Wizard You may click Setup Wizard to quickly configure your router. If you want to enter your settings without running the wizard, click Manual Configure and skip to page 16. Click Launch Internet Connection Setup Wizard to begin.
Section 3 - Configuration Click Next to continue. Create a new password and then click Next to continue. Select your time zone from the drop-down menu and then click Next to continue. Select the type of Internet connection you use and then click Next to continue.
Section 3 - Configuration If you selected Dynamic, you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click Clone Your PC’s MAC Address and then click Next to continue. The Host Name is optional but may be required by some ISPs. The default host name is the device name of the Router and may be changed. If you selected PPPoE, enter your PPPoE username and password. Click Next to continue.
Section 3 - Configuration If you selected L2TP, enter your L2TP username and password. Click Next to continue. If you selected Static, enter your network settings supplied by your Internet provider. Click Next to continue. If you selected Big Pond, select your authentication server from the drop down menu. You will also need to enter your Big Pond username and password. Click Next to continue.
Section 3 - Configuration If you selected Russian PPPoE, enter your PPPoE username and password. Click Next to continue. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. If you selected Russian PPTP, enter your PPTP username and password. Click Next to continue. Click Connect to save your settings.
Section 3 - Configuration Manual Configuration Dynamic (Cable) My Internet Select Dynamic IP (DHCP) to obtain IP Address Connection: information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for Cable modem services. Host Name: The Host Name is optional but may be required by some ISPs. MAC Address: The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router.
Section 3 - Configuration Internet Setup PPPoE (DSL) Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. My Internet Select PPPoE (Username/Password) from the drop-down menu.
Section 3 - Configuration Internet Setup PPTP Choose PPTP (Point-to-Point-Tunneling Protocol) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. IP Address: Enter the IP address (Static PPTP only).
Section 3 - Configuration Internet Setup L2TP Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. IP Address: Enter the L2TP IP address supplied by your ISP (Static only).
Section 3 - Configuration Internet Setup Big Pond (Australia) My Internet Select BigPond (Australia) from the drop-down Connection: menu. Username: Enter your BigPond username. Password: Enter your BigPond password and then retype the password in the next box. Auth Server: Select the type of authentication server being used from the drop-down menu. Login Server IP: Enter the IP address of the login server.
Section 3 - Configuration Internet Setup Static (assigned by ISP) Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The router will not accept the IP address if it is not in this format.
Section 3 - Configuration Internet Setup Russian PPPoE (DSL) Choose Russian PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses.
Section 3 - Configuration Internet Setup Russian PPTP Choose Russian PPTP (Point-to-Point-Tunneling Protocol) if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. Server IP/Name: Enter the Server IP provided with your ISP. PPTP Account: Enter your PPTP account (username).
Section 3 - Configuration Network Settings This section will allow you to change the local network settings of the router and to configure the DHCP settings. Router IP Address: Enter the IP address of the router. The default IP address is 192.168.0.1. If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the configuration utility. Default Subnet Enter the Subnet Mask. The default subnet mask is Mask: 255.255.255.0.
Section 3 - Configuration DHCP Server Settings The router has a built-in DHCP (Dynamic Host Control Protocol) server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the router.
Section 3 - Configuration DHCP Reservation If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range. DHCP Check the box under the first column to enable Reservations List: the reservation. Computer Name: Enter the computer name or select from the drop-down menu (last column) and click <<.
Section 3 - Configuration VPN Settings The DIR-130 supports IPSec, PPTP, and L2TP VPN as the Server Endpoint. Add VPN Profile: Select IPSec or PPTP/L2TP from the drop-down menu and then click Add.
Section 3 - Configuration IPSec Settings Enable: Check this box to enable IPSec. Name: Enter a name for your VPN. Local Net/ Mask: Enter the local (LAN) subnet and mask. (ex. 192.168.0.0/24) Remote IP: Select Site to Site or Remote User for the required VPN configuration. • Site to Site - Network-to-network VPN in which two entire LAN networks are virtually connected across the Internet.
Section 3 - Configuration • Additional Authentication Methods (Optional) XAUTH - Check this box to include additional username and password authentication requirements for the VPN. Select Server Mode or Client Mode. • Server Mode - Select a group from the Authentication database drop-down menu containing the list of user credentials permitted. • Client Mode - Enter the user name and password if required by the remote VPN server endpoint configured in xAuth Server Mode.
Section 3 - Configuration Keep Alive / DPD: Select None, Keep Alive, or DPD (Dead Peer Connection). • None - Select this option to disable Keep Alive. • Keep Alive - Select this option to send random ping requests from this endpoint to the remote endpoint keeping the tunnel established during long idle periods of inactivity. • DPD - Select this option to delete the VPN tunnel if there is no traffic detected. The VPN will re-establish once traffic is again sent through the tunnel.
Section 3 - Configuration PPTP/L2TP Settings PPTP uses TCP port 1723 for its control connection and uses GRE (IP protocol 47) for the PPP data. PPTP supports data encryption by used MPPE. L2TP uses UDP protocol to transport the PPP data. This is often encapsulated in IPSec encryption instead of MPPE. Enable Setting: Check this box to enable. Name: Enter a name for your VPN. Connection Type: Select PPTP, L2TP, or L2TP over IPSec.
Section 3 - Configuration Port Forwarding This section allows you to open a single port or a range of ports. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Configuration Application Rules Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DIR-130.
Section 3 - Configuration MAC Filters Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the Network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the router. You may enter up to 25 rules.
Section 3 - Configuration Website Filters Website Filters are used to deny LAN computers from accessing specific web sites by the URL or domain. A URL is a specially formatted text string that defines a location on the Internet. If any part of the URL contains the blocked word, the site will not be accessible and the web page will not display. To use this feature, enter the text string to be blocked and click Save Settings. The text to be blocked will appear in the list.
Section 3 - Configuration Firewall Settings DMZ A firewall protects your network from the outside work. The D-Link DIR-130 offers a firewall protection such as SPI (Stateful Packet Inspection) and NAT/PAT (Network Address Translation/Port Address Translation). Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ (Demilitarized Zone).
Section 3 - Configuration Firewall Settings Firewall Rules Up to 75 Firewall Rules can be created to control the incoming and outgoing traffic on your router. For each rule you can create a name and control the direction of traffic. You can also allow or deny a range of IP Addresses, protocol and a port range. In order to apply a schedule to a Firewall Rule, you must first define a schedule on the Maintenance > Schedules page. The first 2 Firewall Rules are default and cannot be changed.
Section 3 - Configuration Advanced Network Settings UPnP: Click on the checkbox to enable Universal Plug and Play (UPnP™). UPnP provides compatibility with networking equipment, software and peripherals. Enable WAN Ping Unchecking the box will not allow the DIR-130 Respond: to respond to pings. Blocking pings may provide some extra security from hackers. Check the box to allow the Internet port to be “pinged”. WAN Port Speed: You may set the port speed of the Internet port to 10Mbps, 100Mbps, or Auto.
Section 3 - Configuration Routing This section allows you to define static routes for the WAN types of Static IP, Dynamic IP, Russian PPPoE, and Russian PPTP with ISPs that require these parameters. Up to 50 Static Routing Rules can be defined. Interface: Select WAN or WAN_Physical from the drop down menu. Only select WAN_Physical if your Internet connection type is Russian PPPoE or Russian PPTP. Destination Enter the destination address for the static routing Address: rule.
Section 3 - Configuration Certificates This section is used to configure Certificates that are used with an IPSec based VPN. You can configure local certificates and the certificates of remote peers. Select one of the three options from the drop-down menu: Local Certificate & Private key, Certificate of Remote Peers, or Certificate Authorities. Local Certificate Select this option from the drop-down menu to & Private Key: configure your local certificates. Enter a name for the certificate.
Section 3 - Configuration User Groups This section is used to configure Certificates that are used with an IPSec based VPN. You can configure local certificates and the certificates of remote peers. Select one of the three options from the drop-down menu: Local Certificate & Private key, Certificate of Remote Peers, or Certificate Authorities. Authentication Select a user group from the menu and click the Database: EDIT button to configure that group. Group Name: Enter a name for the user group.
Section 3 - Configuration Administrator Settings This page will allow you to change the Administrator password. You can also enable Remote Management. Admin Password: Enter a new password for the administrator login. Only the administrator can make changes to the settings. Enable Remote Remote management allows the router to be Management: configured from the Internet by a web browser. A username and password is still required to access the Web-Management interface.
Section 3 - Configuration Time and Date The Time and Date page allows you to configure, update, and maintain the correct time and date on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configure to automatically adjust the time when needed. Time Zone: Select the Time Zone from the drop-down menu. Enable Daylight Check the checkbox to enable daylight savings Saving: time. Sync.
Section 3 - Configuration System Settings Save Settings to Use this option to save the current router Local Hard Drive: configuration settings to a file on the hard disk of the computer you are using. First, click the Save Configuration button. You will then see a file dialog, where you can select a location and file name for the settings. Load Settings Use this option to load previously saved from Local Hard router configuration settings.
Section 3 - Configuration Update Firmware You can upgrade the firmware of the router here. Make sure the firmware you want to use is on the local hard drive of the computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site.
Section 3 - Configuration DDNS DDNS (Dynamic Domain Name System) is a method of keeping a domain name linked to a changing IP Address. The DDNS feature allows you to host a server (Web, FTP, Game Server, etc.) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic IP addresses.
Section 3 - Configuration System Check The router System Check uses a ping test to send ping packets to test if a computer in on the Internet. Ping Test: Enter the IP address that you wish to ping and click the Ping button. Ping Results: The results of your ping attempts will be displayed here.
Section 3 - Configuration Schedules This section is used to manage schedule rules for port forwarding, firewall rules, web filtering, and remote Name: Enter a name for your new schedule. Days: Select a day, a range of days, or All Week to include every day. Time: Check All Day - 24hrs or enter a start and end time for your schedule. Save: Click Save to save your schedule. You must click Save Settings at the top for your schedules to go into effect. Schedule Rules The list of schedules will be listed here.
Section 3 - Configuration Log Settings SMTP Server/IP The address of the SMTP server that will be Address: used to send the logs. Email Address: The email address to which the logs will be sent. Click on Send Mail Now to send the email. Save Log File to Click to save the log to your hard drive. Local Hard Drive: Log Type: Select the type of log you would like to view.
Section 3 - Configuration Device Information This page displays the current information for the DIR-130. It will display the LAN, WAN (Internet), and the firmware version of the router. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed.
Section 3 - Configuration Log This page displays the log events of the router. Here you can view the logs of the router. First Page: This button will direct you to the current first page of the log. Last Page: This button will direct you to the current last page of the log. Previous: Click to view the previous page of the log. Next: Click to view the next page of the log. Clear: Clears all current log content.
Section 3 - Configuration Statistics This page displays the current statistics of the router. Here you can view the amount of packets that pass through the router. Refresh: This button will refresh the statistics to display updated information. Reset: This button will reset the statistics packet count to zero for all interfaces listed. WAN: Displays the amount of packets transmitted and received on the WAN interface. LAN: Displays the amount of packets transmitted and received on the LAN interface.
Section 3 - Configuration Active Session The Active Session Status menu shows the active sessions currently running on your router. The list will display the protocol, the source IP address and the destination IP address for each active session. First Page: This button will direct you to the current first page of the active sessions. Last Page: This button will direct you to the current last page of the active sessions. Previous: This button will direct you to the previous page of the active sessions.
Section 3 - Configuration LAN Clients This page displays a list of currently connected wired clients. This table also displays the connection time and MAC address of the connected wired clients. Routing This page displays a list of the default and static routes used by the router.
Section 3 - Configuration VPN The VPN table displays a list of current PPTP, L2TP, L2TP over IPSec, and IPSec VPN sessions. Help The support menu provides additional information regarding features included in the DIR-130 Web Management Interface.
Section 4 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DIR-130. Read the following descriptions if you are having problems. (The examples below are illustrated in Windows® Vista™ and XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples.) 1.
Section 4 - Troubleshooting • Configure your Internet settings: • Go to Start > Control Panel. In Windows® XP or Windows Vista™, make sure you are in Classic View. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK.
Section 4 - Troubleshooting 3. Why can’t I connect to certain sites or send and receive e-mails when connecting through my router? If you are having a problem sending or receiving e-mail, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to.
Section 4 - Troubleshooting You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size.
Appendix A - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter or if you already have an Ethernet adapter installed on your computer, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. router) automatically. To verify your IP address, please follow the steps below. Windows Vista™ Users: • Click Start > All Programs > Accessories > Command Prompt. You may need administrative access to run this application.
Appendix A - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Windows® XP/2000 Users • Windows® XP - Click on Start > Control Panel. Make sure you are in Classic View. Double-click on the Network Connections icon. Windows® 2000 – From the desktop, right-click My Network Places > Properties.
Appendix A - Networking Basics Windows Vista™ Users • Click on Start > Control Panel. Make sure you are in Classic View. Double-click on the Network and Sharing Center icon. Along the left panel in the window, click on Manage network connections. • Right-click on the Local Area Connection which represents your D-Link network adapter (or other adapter) which will be connected to your router. • Highlight Internet Protocol Version 4 (TCP /IPv4) and click Properties.
Appendix B - Technical Specifications Technical Specifications Standards • IEEE 802.3 • IEEE 802.3u LEDs • Power • Status • WAN • LAN (1-8) Operating Temperature • 32°F to 104°F ( 0°C to 40°C) Humidity • 95% maximum (non-condensing) Safety & Emissions • FCC • CE • IC Dimensions • L = 7.6 inches • W = 4.6 inches • H = 1.
Appendix B - Technical Specifications Default Factory Settings When you receive your router, the default factory settings are in effect as listed in the table below. You may change any of the network settings. If you perform a reset (hold the reset button on the back of the unit), the router will reset with the following settings: D-Link DIR-130 User Manual Setting Default Value Username admin Password (leave blank) LAN IP Address 192.168.0.1 DHCP Server Enabled DHCP IP Range 192.168.0.
Appendix C - Contacting Technical Support Contacting Technical Support U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. Before you contact technical support, please have the following ready: • Model number of the product (e.g. DIR-130) • Hardware Revision (located on the label on the bottom of the router (e.g. rev A1)) • Serial Number (s/n number located on the label on the bottom of the router).
Appendix D - Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Appendix D - Warranty Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation.
Appendix D - Warranty • After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. DLink will only replace the defective portion of the product and will not ship back any accessories.
Appendix D - Warranty IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT.
Appendix D - Warranty CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix E - GNU/Linux GPL GNU/Linux GPL • “GPL Software” means GPL software licensed to you under the GNU General Public License as published by the Free Software Foundation (GPL). A copy of the GPL is included below. • “Open Source Software” means various open source software components licensed under the terms of applicable open source license agreements included in the materials relating to such software.
Appendix E - GNU/Linux GPL GNU General Public License Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The licenses for most software are designed to take away your freedom to share and change it.
Appendix E - GNU/Linux GPL Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow.
Appendix E - GNU/Linux GPL b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
Appendix E - GNU/Linux GPL The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable.
Appendix E - GNU/Linux GPL It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices.
Appendix E - GNU/Linux GPL 12.
Appendix F - Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.
