Networking Basics Sharing a network printer ! Click on Add a printer ! Click Next ! Select Network Printer ! Click Next 62
Networking Basics Sharing a network printer ! Select Browse for a printer ! Click Next Select the printer you would like to share ! Click Next ! Click Finish 63
Networking Basics Sharing a network printer ! To check for proper installation: ! Go to Start > Printers and Faxes The printer icon will appear at right, indicating proper installation. You have completed adding the printer.
Networking Basics Sharing an LPR printer To share an LPR printer (using a print server,) you will need a Print Server such as the DP-101P+. Please make sure that you have run the Network Setup Wizard on all the computers on your network. To share an LPR printer, please follow these directions: ! Go to Start > Printers and Faxes ! Click on Add a Printer The screen to the right will appear ! Click Next ! Select Local Printer...
Networking Basics Sharing an LPR printer ! Select Create a new port ! From the pull-down menu, select Standard TCP/IP Port, as shown. ! Click Next ! Please read the instructions on this screen ! Click Next ! Enter the Printer IP Address and the Port Name, as shown.
Networking Basics Sharing an LPR printer ! In this screen, select Custom ! Click Settings ! Enter the Port Name and the Printer Name or IP Address. ! Select LPR ! Enter a Queue Name (if your PrintServer/ Gateway has more than one port, you will need a Queue name.
Networking Basics Sharing an LPR printer ! This screen will show you information about your printer. ! Click Finish ! Select the printer you are adding from the list of Printers. ! Insert the printer driver disk that came with your printer.
Networking Basics Sharing an LPR printer ! You can rename your printer if you choose. It is optional. ! Please remember the name of your printer. You will need this information when you use the Add Printer Wizard on the other computers on your network. ! Click Next ! Select Yes, to print a test page. ! Click Next This screen will display information about your printer. ! Click Finish to complete the addition of the printer.
Troubleshooting This Chapter provides solutions to problems that can occur during the installation and operation of the DI-754 Wireless Broadband Router. We cover various aspects of the network setup, including the network adapters. Please read the following if you are having problems. Note: It is recommended that you use an Ethernet connection to configure the DI-754 Wireless Broadband Router. 1.The computer used to configure the DI-754 cannot access the Configuration menu.
Troubleshooting 2. The wireless client cannot access the Internet in the Infrastructure mode. Make sure the wireless client is associated and joined with the correct Access Point. To check this connection: Right-click on the Local Area Connection icon in the taskbar> select View Available Wireless Networks. The Connect to Wireless Network screen will appear. Please make sure you have selected the correct available network, as shown in the illustrations below.
Troubleshooting 3. Check that the drivers for the network adapters are installed properly. You may be using different network adapters than those illustrated here, but this procedure will remain the same, regardless of the type of network adapters you are using.
Troubleshooting ! Double-click on Network Adapters ! Right-click on D-Link AirPro DWL-A650 Wireless Cardbus Adapter ! Select Properties to check that the drivers are installed properly ! Look under Device Status to check that the device is working properly ! Click OK 73
Troubleshooting 4. What variables may cause my wireless products to lose reception? D-Link products let you access your network from virtually anywhere you want. However, the positioning of the products within your environment will affect the wireless range. Please refer to Installation Considerations in the Wireless Basics section of this manual for further information about the most advantageous placement of your D-Link wireless products. 5.
Troubleshooting 7. Resetting the DI-754 to Factory Default Settings After you have tried other methods for troubleshooting your network, you may choose to Reset the DI-754 to the factory default settings. Remember that D-Link AirPro products network together, out of the box, at the factory default settings.
Technical Specifications Standards ! ! ! ! Ports IEEE 802.11b (optional with DWL-650+) IEEE 802.11a IEEE 802.3 and IEEE 802.3u IEEE 802.3x ! (1) 10/100Base-T Ethernet, RJ-45 (UTP) ! (1) Power – 5V DC, 3.0A Network Management ! Web-Based Interface Network Architecture ! Supports Infrastructure Mode Diagnostic LED ! ! ! ! ! ! ! Power M1 M2 WAN WLAN 802.11a WLAN 802.
Technical Specifications Emissions: ! FCC part 15b ! UL1950-3 Physical Dimensions: ! L = 9.25 inches ! W = 6.25 inches ! H = 1.50 inches 802.11a Specifications Data Rates: ! 6, 9, 12, 18, 24, 36, 48, 54, 72 Mbps (with auto-Fallback) Data Security: ! 64, 128, 152 bit with Dynamic Keying ! Access Control List Antenna Type: ! External 5dBi dipole antenna with diversity Available Channels: ! Eight non-overlapping channels for North America Frequency Range: ! 5.150 – 5.
802.11a Specifications (continued) Modulation Techniques: ! ! ! ! BPSK QPSK 16 QAM 64 QAM 802.11b Specifications with optional DWL-650+ Data Rates: ! 1, 2, 5.5, 11, 22 Mbps (with Automatic Fallback) Data Security: ! 64, 128, 256-bit WEP (Wired Equivalent Privacy) Encryption Available Channels: ! Eleven channels for North America. Three non-overlapping. Frequency Range: ! 2.4 – 2.4835 GHz Modulation Techniques: ! ! ! ! ! ! ! Barker (1Mbps/0db) Barker (2Mbps/0db) CCK (5.5Mbps/5.5db) PBCC (5.5Mbps/1.
802.11b Specifications (with optional DWL-650+)-continued Modulation Technology: ! PBCC - Packet Binary Convolutional Coding ! Direct Sequence Spread Spectrum (DSSS) ! 11-chip Barker sequence Contacting Technical Support You can find the most recent software and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States for the duration of the warranty period on this product. U.S.
Warranty and Registration Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited warranty for its product only to the person or entity that originally purchased the product from: ! ! D-Link or its authorized reseller or distributor and Products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, addresses with an APO or FPO.
! The original product owner must obtain a Return Material Authorization (“RMA”) number from the Authorized D-Link Service Office and, if requested, provide written proof of purchase of the product (such as a copy of the dated purchase invoice for the product) before the warranty service is provided.
Governing Law: This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This limited warranty provides specific legal rights and the product owner may also have other rights which vary from state to state. Trademarks: D-Link is a registered trademark of D-Link Systems, Inc.
