Preface D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Manual Revisions Revision Date Description 1.0 September 01, 2010 DHP-1320 Revision A1 Trademarks D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
Table of Contents Table of Contents Preface............................................................................................................ i Manual Revisions................................................................................................i Trademarks...........................................................................................................i Product Overview........................................................................................ 1 Package Contents.
Table of Contents IPv6 Routing . ..................................................................................................85 Tools....................................................................................................................86 Admin........................................................................................................86 Time...........................................................................................................87 SysLog......................
Table of Contents Check your IP address................................................................................ 162 Statically Assign an IP address................................................................ 163 Technical Specifications.........................................................................164 Contacting Technical Support...............................................................166 Warranty....................................................................................
Section 1 - Product Overview Product PackageOverview Contents DHP-1320 Wireless N PowerLine Router Two Detachable Antennas Ethernet Cable Power Adapter CD-ROM with Manual and Setup Wizard Note: Using a power supply with a different voltage rating than the one included with the DHP-1320 will cause damage and void the warranty for this product.
Section 1 - Product Overview System Requirements Network Requirements • An Ethernet-based Cable or DSL modem • IEEE 802.11n or 802.11g wireless clients • 10/100 Ethernet Computer with the following: • Windows®, Macintosh, or Linux-based operating system • An installed Ethernet adapter Web-based Configuration Utility Requirements Browser Requirements: • Internet Explorer 6 or higher • Firefox 3.0 or higher • Safari 3.0 or higher • Chrome 2.
Section 1 - Product Overview Introduction TOTAL PERFORMANCE Combines award winning router features and IEEE 802.11n/g wireless technology to provide the best wireless performance. TOTAL SECURITY The most complete set of security features including Active Firewall and WPA/WPA2 to protect your network against outside intruders. TOTAL COVERAGE Provides greater wireless signal rates even at farther distances for best-in-class Whole Home Coverage.
Section 1 - Product Overview Features • Faster Wireless Networking - The DHP-1320 provides up to 300Mbps* wireless connection with other 802.11n wireless clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming, and real-time audio. The performance of this 802.11n wireless router gives you the freedom of wireless networking at speeds 650% faster than 802.11g. • Compatible with 802.
Section 1 - Product Overview Hardware Overview Connections 1 1 2 3 4 5 6 7 AP-Router Switch Two-way switch used to Select AP or Router Mode. 2 LAN Ports (1-3) 3 Internet Port The auto MDI/MDIX Internet port is the connection for the Ethernet cable to the cable or DSL modem. 4 Reset Button Pressing the Reset button restores the router to its original factory default settings.
Section 1 - Product Overview Hardware Overview WPS Button 1 2 1 WPS Button Press the WPS button for one second to initiate the WPS process. The button will flash blue while a WPS connection is being established. The button will light solid blue for 5 seconds when the device has successfully been added to the network. 2 ENY Button Push this button to establish a secure PowerLine network with other PowerLine AV devices.
Section 1 - Product Overview Hardware Overview LEDs 1 2 3 4 5 6 1 Power LED A solid green light indicates a proper connection to the power supply. This LED will light orange during a factory reset or reboot. A slow blinking orange LED indicates that the Router has crashed during bootup. 2 Internet LED A solid green light indicates that the internet connection has successfully completed. This LED blinks green during data transmission.
Section 2 - Installation Installation This section will walk you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area such as a closet, cabinet, or in the attic or garage. Before you Begin • Please configure the router with the computer that was last connected directly to your modem. • You can only use the Ethernet port on your modem.
Section 2 - Installation Wireless Installation Considerations The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Section 2 - Installation Hardware Installation - For Router Mode 1 LAN 2 INTERNET RESET USB ON/OFF AC IN 3 AR RT Start Here Windows users can use the Quick Router Setup Wizard (from the CD) to configure their router. If you do not want to use the wizard, lost your CD, or are running Mac or Linux, you will need to use the manual setup procedure below. Quick Router Setup Wizard For the Wizard to work, the computer must be connected to the Internet and be online.
Section 2 - Installation Connect to Cable/DSL/Satellite Modem If you are connecting the router to a cable/DSL/satellite modem, please follow the steps below: 1. Place the router in an open and central location. Do not plug the power adapter into the router. 2. Unplug the modem’s power adapter. 3. Unplug the Ethernet cable (that connects your computer to your modem) from your computer and place it into the Internet port on the router. 4. Plug an Ethernet cable into one of the three LAN ports on the router.
Section 2 - Installation Connect to Another Router If you are connecting the D-Link router to another router to use as a wireless access point and/or switch, you will have to do the following before connecting the router to your network: • Disable UPnP™ • Disable DHCP • Change the LAN IP address to an available address on your network. The LAN ports on the router cannot accept a DHCP address from your other router. To connect to another router, please follow the steps below: 1.
Section 2 - Installation 6. Disconnect the Ethernet cable from the router and reconnect your computer to your network. 7. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. Do not plug anything into the Internet (WAN) port of the D-Link router. 8. You may now use the other 2 LAN ports to connect other Ethernet devices and computers. To configure your wireless network, open a web browser and enter the IP address you assigned to the router.
Section 2 - Installation Hardware Installation - For Access Point Mode Room 1 Room 2 DHP-306AV Wireless Router Modem RESET 1 2 1 LAN 2 LAN 3 4 INTERNET INTERNET RESET USB ON/OFF USB INTERNET 5V - - - 3A AC IN 3 AR RT DHP-306AV Wireless N PowerLine Router (AP Mode) Room3 Step 1 Move the switch on the back of the DHP-1320 to “AP”. Connect the supplied power cord into the power receptor located on the back of the DHP1320 and plug into a power outlet as illustrated in Room 3.
Section 1 - Product Overview PowerLine Installation Considerations Plan the location of your PowerLine devices: 1. Connect the PowerLine devices to electrial outlets that are not controlled by a wall switch in order to avoid accidentally turning off the power to the device. 2. Do not connect the Wireless N PowerLine Router to an extension cord, surge protector, or power strip. This might prevent the device from working correctly or it may reduce the network performance. 3.
Section 1 - Product Overview PowerLine Security It is strongly recommended to encrypt your PowerLine network. By encrypting the data that is sent via your PowerLine adapters, you will prevent nearby hackers with a Powerline adapter to connect to your network and steal your information. To encrypt your PowerLine network, follow the steps below: PowerLine Network-Quick Setup Encryption Button Usage The ENY Button is used to add a PowerLine AV device to a PowerLine network.
Section 1 - Product Overview Configuring a PowerLine Network Connecting two PowerLine AV devices for the first time To initially connect the DHP-1320 AV to another PowerLine AV device and create a network: 1. Plug the DHP-1320 into a power outlet. Press the ENY button for 1 to 3 seconds. The PowerLine AV LED should start to blink. 2. Plug the other PowerLine device (e.g. the DHP-W306AV) into a power outlet. Press the ENY button on this PowerLine device for 1 to 3 seconds. 3.
Section 1 - Product Overview Connecting a PowerLine AV device to an existing PowerLine network To add a DHP-1320 if you already have an existing network with 2 more PowerLine devices: 1. Press the ENY button on the DHP-1320 for more than 10 seconds to make sure it is not connected to any other PowerLine network. 2. Press the ENY button of any device already in your PowerLine network (e.g. the DHP-306AV) for 1 to 3 seconds. The ENY LED should start to blink. 3.
Section 2 - Installation Getting Started The DHP-1320 includes a Quick Router Setup Wizard CD. Follow the simple steps below to run the Setup Wizard to guide you quickly through the installation process. Insert the Quick Router Setup Wizard CD in the CD-ROM drive. The step-by-step instructions that follow are shown in Windows® XP. The steps and screens are similar for the other Windows operating systems. If the CD Autorun function does not automatically start on your computer, go to Start > Run.
Section 3 - Configuration Configuration (Router Mode) This section will show you how to configure your new D-Link wireless router using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router (192.168.0.1). Select Admin in the User Name field. Leave the password blank by default.
Section 3 - Configuration Setup Internet This section allows you to configure your Router’s Internet settings. Internet The Internet Connection Setup Wizard provides a quick Connection method for configuring your Internet settings. To start Setup Wizard: the Internet Connection Setup Wizard, click the Internet Connection Setup Wizard button. Refer to “Internet Connection Setup Wizard” on page 22 for more information on how to use the Internet Connection Setup Wizard.
Section 3 - Configuration Internet Connection Setup Wizard Click the Internet Connection Setup Wizard button to start the Internet Connection Setup Wizard.
Section 3 - Configuration The following window appears, summarizing the steps required to complete the Internet Connection Setup Wizard: Click Next to continue. Create a new password and then click Next to continue. Select your time zone from the drop-down menu and then click Next to continue.
Section 3 - Configuration Select the type of Internet connection you use and then click Next to continue. If you selected DHCP Connection (Dynamic IP Address), you may need to enter the MAC address of the computer that was last connected directly to your modem. If you are currently using that computer, click Clone Your PC’s MAC Address and then click Next to continue. The Host Name is optional but may be required by some ISPs. The default host name is the device name of the router and may be changed.
Section 3 - Configuration If you selected PPPoE, enter your PPPoE username and password. If your ISP requires you to enter a PPPoE service name, enter the service name in the Service Name field. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. Click Next to continue. Note: Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
Section 3 - Configuration If you selected L2TP, enter your L2TP username and password. Select Static if your ISP assigned you the IP address, subnet mask, gateway, and L2TP server addresses. Click Next to continue. If you selected Static, enter your network settings supplied by your Internet provider. Click Next to continue.
Section 3 - Configuration Click Connect to save your settings. The following window appears to indicate that the settings are being saved. When the Router has finished saving all the changes, the Setup> Internet window will open. Close your browser window and reopen it to test your Internet connection. It may take a few tries to initially connect to the Internet.
Section 3 - Configuration Manual Internet Connection Setup Internet Use the My Internet Connection is drop-down menu to Connection select the mode that the router should use to connect to Type: the Internet. Advanced Advanced Domain Name System (DNS) Services enhances DNS Service: your Internet performance by getting you the information and web pages you are looking for faster and more reliably.
Section 3 - Configuration Manual Internet Connection Setup Static IP Select Static IP from the drop-down menu if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
Section 3 - Configuration Manual Internet Connection Setup Dynamic IP (DHCP) Select Dynamic IP (DHCP) from the drop-down menu to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP numbers to use. This option is commonly used for cable modem services such as Comcast and Cox. Host Name: The Host Name is optional but may be required by some ISPs. Leave blank if you are not sure.
Section 3 - Configuration Manual Internet Connection Setup PPPoE (Username/Password) Select PPPoE (Username/Password) from the drop-down menu if your ISP uses a PPPoE connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The software is no longer needed and will not work through a router.
Section 3 - Configuration MAC Address: The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card. Click the Save Settings button to save any changes made.
Section 3 - Configuration Manual Internet Connection Setup PPTP Select PPTP (Point-to-Point Tunneling Protocol) from the drop-down menu if your ISP uses a PPTP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Address Mode: Select Static IP if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic IP. PPTP IP Address: Enter the IP address (Static PPTP only).
Section 3 - Configuration MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU. MAC Address: The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP.
Section 3 - Configuration Manual Internet Connection Setup L2TP Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a username and password. This option is typically used for DSL services. Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses. In most cases, select Dynamic. L2TP IP Address: Enter the L2TP IP address supplied by your ISP (Static only).
Section 3 - Configuration MTU: Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specific ISP. 1454 is the default MTU. MAC Address: The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not recommended that you change the default MAC address unless required by your ISP.
Section 3 - Configuration Wireless Settings If you want to configure the wireless settings on your router using the wizard, click Wireless Connection Setup Wizard and refer to “Wireless Connection Setup Wizard” on page 103. Click Add Wireless Device with WPS if you want to add a wireless device using Wi-Fi Protected Setup (WPS) and refer to “Add Wireless Device with WPS Wizard” on page 106.
Section 3 - Configuration Manual Wireless Settings 802.11n/b/g (2.4GHz) Enable Wireless: Check the box to enable the wireless function. If you do not want to use wireless, uncheck the box to disable all the wireless functions. Schedule: Select the time frame that you would like your wireless network enabled. The schedule may be set to Always. Any schedule you create will be available in the drop-down menu. Click New Schedule to create a new schedule.
Section 3 - Configuration Channel Width: Select the Channel Width: Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices. 20MHz - Select if you are not using any 802.11n wireless clients. This is the default setting. Wireless Security Refer to “Wireless Security” on page 136 for more information regarding wireless security. Mode: Click the Save Settings button to save any changes made.
Section 3 - Configuration Network Settings This section will allow you to change the local network settings of the router and to configure the DHCP settings. Router Use this section to configure the Router’s local network Settings: settings. DHCP Server Use this section to configure the DHP-1320’s built-in DHCP Settings: server settings. Add DHCP Use this section to create a new DHCP reservation or Reservation: manage existing DHCP reservations.
Section 3 - Configuration Network Settings Router Settings Router IP Address: Enter the IP address of the router. The default IP address is 192.168.0.1. If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to get back into the configuration utility. Default Subnet Enter the Subnet Mask. The default subnet mask is Mask: 255.255.255.0. Device Name: Enter a Host Name to identify the DHP-1320. Local Domain: Enter the Domain name (Optional).
Section 3 - Configuration Network Settings DHCP Server Settings DHCP stands for Dynamic Host Control Protocol. The DHP-1320 has a built-in DHCP server. The DHCP Server will automatically assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load the proper TCP/IP settings provided by the DHP-1320.
Section 3 - Configuration Network Settings DHCP Reservation If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP address only to that computer or device. Note: This IP address must be within the DHCP IP Address Range. Enable: Check this box to enable the reservation. Computer Enter the computer name.
Section 3 - Configuration USB Settings In this section you may configure your USB port. You can select several configurations to choose from such as Share Port and WCN Configuration.
Section 3 - Configuration PLC Settings (Router Mode) This section will show you how to configure your new D-Link PowerLine AV using the web-based configuration utility.
Section 3 - Configuration Network You can set the name of your network and to make it Name: either public or private. Make sure the Network Name of all of the devices within your PowerLine network is the same. Public Select this option if you would like to make your powerline Network network public with the default Network Name of Name: “HomePlugAV”. Since this is a commonly used Network Name, it is less secure than a private Network Name.
Section 3 - Configuration Member List: This section provides information on the PowerLine AV devices in your PowerLine network, or any devices that were previously connected but it are currently disconnected. Link Rate: Displays the device’s current data rate in Mbps. Status: This field shows the status of the device. If the field displays the word Connect, then the device is connected to your PowerLine network.
Section 3 - Configuration Advanced Virtual Server The DHP-1320 can be configured as a virtual server so that remote users accessing Web or FTP services via the public IP address can be automatically redirected to local servers in the LAN (Local Area Network). The DHP-1320 firewall feature filters out unrecognized packets to protect your LAN network so all computers networked with the DHP-1320 are invisible to the outside world.
Section 3 - Configuration The Virtual Server window allows you to open a single port. If you would like to open a range of ports, refer to the next page. Enable Check the box on the left side to enable the Virtual Checkbox: Server rule. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Configuration Port Forwarding This will allow you to open a single port or a range of ports. Enable Checkbox: Tick the checkbox on the left side to enable the Port Forwarding rule. Name: Enter a name for the rule or select an application from the drop-down menu. Select an application and click << to populate the fields. IP Address: Enter the IP address of the computer on your local network that you want to allow the incoming service to.
Section 3 - Configuration Application Rules Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others. These applications have difficulties working through NAT (Network Address Translation). Special Applications makes some of these applications work with the DHP1320.
Section 3 - Configuration QoS Engine The QoS Engine option helps improve your network gaming performance by prioritizing applications. By default the QoS Engine settings are disabled and application priority is not classified automatically. Enable Traffic This option is disabled by default. Enable this option Shapping: for better performance and experience with online games and other interactive applications, such as VoIP.
Section 3 - Configuration Network Filter Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from accessing the network. You can either manually add a MAC address or select the MAC address from the list of clients that are currently connected to the Broadband Router.
Section 3 - Configuration Access Control The Access Control section allows you to control access in and out of your network. Use this feature as Parental Controls to only grant access to approved sites, limit web access based on time or dates, and/or block access from applications like P2P utilities or games. Add Policy: Check the Enable Access Control check box and click the Add Policy button to start the Access Control Wizard. Access Control Wizard Click Next to continue with the wizard.
Section 3 - Configuration Enter a name for the policy and then click Next to continue. Select a schedule (I.E. Always) from the drop-down menu and then click Next to continue. Enter the following information and then click Next to continue. • Address Type - Select IP address, MAC address, or Other Machines. • IP Address - Enter the IP address of the computer you want to apply the rule to.
Section 3 - Configuration Select the filtering method and then click Next to continue. Enter the rule: Enable - Check to enable the rule. Name - Enter a name for your rule. Dest IP Start - Enter the starting IP address. Dest IP End - Enter the ending IP address. Protocol - Select the protocol. Dest Port Start - Enter the starting port number. Dest Port End - Enter the ending port number. To enable web logging, click Enable. Click Save to save the access control rule.
Section 3 - Configuration Website Filter Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network. To use this feature select the appropriate Web Filtering option, enter the domain or website, and click Save Settings. Configure Web Select ALLOW computers access to ONLY these sites, or Filtering: DENY computers access to ONLY these sites from the drop-down menu. Website URL: Enter the keywords or URLs that you want to allow or block.
Section 3 - Configuration Inbound Filter The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can configure inbound data filtering rules that control data based on an IP address range. Inbound Filters can be used with Virtual Server, Port Forwarding, or Remote Administration features. Name: Enter a name for the inbound filter rule. Action: Select Allow or Deny. Enable: Check to enable rule. Remote IP Enter the starting IP address. Enter 0.0.
Section 3 - Configuration Firewall Settings A firewall protects your network from the outside world. The DHP-1320 offers a firewall type functionality. The SPI feature helps prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications. If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the chosen computer completely to the outside world.
Section 3 - Configuration DMZ Host: If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer. Carry out the following to create a DMZ host: 1. Check the Enable DMZ box. 2. Specify the IP address of the computer on the LAN that you want to have unrestricted Internet communication in the DMZ IP address field.
Section 3 - Configuration Routing The Routing option is an advanced method of customizing specific routes of data through your network. Routing List: Each Route has a checkbox next to it, check the box of the route you wish to enable. Name: Specify a name for identification of this route. Interface: Select the interface which the IP packet must use to transit out of the router when this route is used. Destination IP: Enter the address of the host or network you wish to access.
Section 3 - Configuration Advanced Wireless Settings 802.11n/b/g (2.4GHz) Transmit Power: Set the transmit power of the antennas. Beacon Period: Beacons are packets sent by an Access Point to synchronize a wireless network. Specify a value. 100 is the default setting and is recommended. RTS Threshold: This value should remain at its default setting of 2346. If inconsistent data flow is a problem, only a minor modification should be made.
Section 3 - Configuration Wi-Fi Protected Setup (WPS) Wi-Fi Protected Setup (WPS) System is a simplified method for securing your wireless network during the “Initial setup” as well as the “Add New Device” processes. The Wi-Fi Alliance (WFA) has certified it across different products as well as manufactures. The process is just as easy, as depressing a button for the Push-Button Method or correctly entering the 8-digit code for the Pin-Code Method.
Section 3 - Configuration Add Wireless Click the Add Wireless Device with WPS button to start Wireless Connection Setup Wizard. This wizard helps you add wireless Station: devices to the wireless network. The wizard will either display the wireless network settings to guide you through manual configuration, prompt you to enter the PIN for the device, or ask you to press the configuration button on the device.
Section 3 - Configuration Advanced Network Enable UPnP: To use the Universal Plug and Play (UPnP™) feature click on Enabled. UPNP provides compatibility with networking equipment, software and peripherals. Enable WAN Ping Unchecking the box will not allow the DHP-1320 to Response: respond to pings. Blocking the Ping may provide some extra security from hackers. Check the box to allow the Internet port to be “pinged”.
Section 3 - Configuration IPv6 Use the IPv6 window to configure the mode that the Router will use to access an IPv6 Internet connection. My IPv6 Use the drop-down menu to select the IPv6 Connection is: Internet Connection mode.
Section 3 - Configuration IPv6 Static IPv6 Select Static IPv6 from the My IPv6 Connection is drop-down menu if your Router will use a static IPv6 address to connect to the Internet. WAN IPv6 Address Enter the address settings supplied by your Internet Settings: provider (ISP). LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN Address Use this section to configure the IPv6 autoconfiguration Autoconfiguration settings.
Section 3 - Configuration IPv6 Static IPv6 - Stateless To configure the Router to use a Static IPv6 Stateless connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable automatic Check to enable the Autoconfiguration feature. IPV6 address assignment: Autoconfiguration Select the Stateless option from the drop-down menu. Type: Router Enter the Router Advertisement Lifetime (in minutes).
Section 3 - Configuration IPv6 Static IPv6 - Stateful To configure the Router to use a Static IPv6 Stateful connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Select the Stateful(DHCPv6) option from the drop-down Type: menu. IPv6 Address Range Enter the start IPv6 Address for the DHCPv6 range for your Start: local computers.
Section 3 - Configuration IPv6 Autoconfiguration (Stateless/DHCPv6) Select Static IPv6 from the My IPv6 Connection is drop-down menu if your Router will use a static IPv6 address to connect to the Internet. IPv6 DNS Settings: Select Obtain DNS Server address automatically or enter a specific DNS server address. LAN IPv6 Address Enter the LAN (local) IPv6 address for the router. Settings: LAN IPv6 Displays the Router’s LAN Link-Local Address.
Section 3 - Configuration IPv6 Autoconfiguration (Stateless/DHCPv6) - Stateless To configure the Router to use a Static IPv6 Stateless connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable automatic Check to enable the Autoconfiguration feature. IPv6 address assignment: Autoconfiguration Select the Stateless option from the drop-down menu. Type: Router Enter the Router Advertisement Lifetime (in minutes).
Section 3 - Configuration IPv6 Autoconfiguration (Stateless/DHCPv6) - Stateful To configure the Router to use a Static IPv6 Stateful connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable automatic Check to enable the Autoconfiguration feature. IPv6 address assignment: Autoconfiguration Select the Stateful(DHCPv6) option from the drop-down Type: menu.
Section 3 - Configuration IPv6 6to4 Select 6to4 from the My IPv6 Connection is drop-down menu if your Router will use a 6 to 4 tunnel to connect to the Internet. Primary DNS Enter the DNS Address supplied by your Internet provider Address: (ISP). LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. Click the Save Settings button to save any changes made.
Section 3 - Configuration IPv6 6to4 - Stateless To configure the Router to use an IPv6 to IPv4 tunnel stateless autoconfiguration connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable automatic Check to enable the Autoconfiguration feature. IPv6 address assignment: Autoconfiguration Select the Stateless option from the drop-down menu. Type: Router Enter the Router Advertisement Lifetime (in minutes).
Section 3 - Configuration IPv6 6to4 - Stateful To configure the Router to use an IPv6 to IPv4 tunnel stateful autoconfiguration connection, configure the parameters in the LAN Address Autoconfiguration Settings section as described below: Enable automatic Check to enable the Autoconfiguration feature. IPv6 address assignment: Autoconfiguration Select the Stateful option from the drop-down menu. Type: IPv6 Address Enter the start IPv6 Address for the DHCPv6 range for Range Start: your local computers.
Section 3 - Configuration IPv6 6rd My IPv6 Select 6rd from the drop-down menu. Connection: 6rd IPv6 Prefix: Enter the settings supplied by your Internet provider (ISP). LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router.
Section 3 - Configuration IPv6 6rd (Stateless) Enable automatic Check to enable the Autoconfiguration feature. IPv6 address assignment: Autoconfiguration Select the Stateless option from the drop-down menu. Type: Router Enter the Router Advertisement Lifetime (in minutes). Advertisement Lifetime: Click the Save Settings button to save any changes made.
Section 3 - Configuration IPv6 6rd (Stateful) Enable automatic Check to enable the Autoconfiguration feature. IPv6 address assignment: Autoconfiguration Select the Stateful DCHPv6 option from the drop-down Type: menu. IPv6 Address Enter the start IPv6 Address for the DHCPv6 range for Range Start: your local computers. IPv6 Address Enter the end IPv6 Address for the DHCPv6 range for Range End: your local computers. IPv6 Address Enter the IPv6 Address Lifetime (in minutes).
Section 3 - Configuration IPv6 IPv6 over IPv4 Tunnel My IPv6 Select IPv6 over IPv4 Tunnel from the drop-down Connection: menu. IPv6 over IPv4 Enter the IPv6 settings supplied by your Tunnel Broker. Tunnel Settings: IPv6 DNS Settings: Obtain a DNS server address automatically or enter a specific DNS server address. Primary/Secondary Enter the primary and secondary DNS server addresses. DNS Address: LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router.
Section 3 - Configuration IPv6 IPv6 over IPv4 Tunnel - Stateless Enable automatic Check to enable the IPv6 address assignment IPv6 address feature. assignment: Autoconfiguration Select Stateless. Refer to the previous page for Type: Stateful. Router Enter the Router Advertisement Lifetime (in Advertisement minutes).
Section 3 - Configuration IPv6 IPv6 over IPv4 Tunnel - Stateful Enable automatic Check to enable the automatic IPv6 address assignment IPv6 address feature. assignment: Autoconfiguration Select Stateful (DHCPv6). Refer to the next page for Type: Stateless. IPv6 Address Enter the start IPv6 Address for the DHCPv6 range for your Range Start: local computers. IPv6 Address Enter the end IPv6 Address for the DHCPv6 range for your Range End: local computers.
Section 3 - Configuration IPv6 Link-local Only Select Link-local Only from the My IPv6 Connection is drop-down menu if your Router will use the IPv6 link local method to connect to the Internet. LAN IPv6 Displays the LAN IPv6 Link-Local address of the router. Address Settings: Click the Save Settings button to save any changes made.
Section 3 - Configuration IPv6 PPPoE The DHP-1320’s IPv6 Firewall feature allows you to configure which kind of IPv6 traffic is allowed to pass through the device. The DHP-1320’s IPv6 Firewall functions in a similar way to the IP Filters feature. My IPv6 Select PPPoE from the drop-down menu. Connection: PPPoE: Enter the PPPoE account settings supplied by your Internet provider (ISP). Address Mode: Select Static if your ISP assigned you the IP address, subnet mask, gateway, and DNS server addresses.
Section 3 - Configuration IPv6 DNS Settings: Select either Obtain DNS server address automatically or Use the following DNS Address. Primary/Secondary Enter the primary and secondary DNS server addresses. DNS Address: LAN IPv6 Address: Enter the LAN (local) IPv6 address for the router. LAN Link-Local Displays the Router’s LAN Link-Local Address. Address: Enable Check to enable the Autoconfiguration feature. Autoconfiguration: Autoconfiguration Select Stateful (DHCPv6) or Stateless.
Section 3 - Configuration IPv6 Routing This page allows you to specify custom routes that determine how data is moved around your network. Routing List: Each Route has a checkbox next to it, check the box of the route you wish to enable. Name: Specify a name for identification of this route. Destination IP: This field identifies the portion of the destination IP in use. Metric: The route metric is a value from 1 to 16 that indicates the cost of using this route.
Section 3 - Configuration Tools Admin This page will allow you to change the Administrator password and configure the authentication settings. This window also allows you to enable Remote Management, via the Internet. Admin Enter a new password for the Administrator Login Name. Password: The administrator can make changes to the settings. User Password: Enter the new password for the User login. If you login as the User, you can only see the settings, but cannot change them.
Section 3 - Configuration Time The Time window allows you to configure, update, and maintain the correct time on the internal system clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be configured to automatically adjust the time when needed. Time Zone: Select the Time Zone from the drop-down menu. Enable Daylight Check this box if the country your are located in uses Saving: Daylight Saving time.
Section 3 - Configuration SysLog The Broadband Router keeps a running log of events and activities occurring on the Router. You may send these logs to a SysLog server on your network. Enable Logging Check this box to send the router logs to a SysLog Server. to SysLog Server: SysLog Server The address of the SysLog server that will be used to IP Address: send the logs. You may also select your computer from the drop-down menu (only if receiving an IP address from the router via DHCP).
Section 3 - Configuration Email Settings The Email feature can be used to send the system log files and router alert messages to your email address. Enable Email When this option is enabled, router activity logs are Notifications: e-mailed to a designated e-mail address. From Email This email address will appear as the sender when you Address: receive a log file or firmware upgrade notification via email. To Email Address: Enter the email address where you want the email sent.
Section 3 - Configuration System This section allows you to manage the router’s configuration settings, reboot the router, and restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created. Save Settings to Use this option to save the current router configuration Local Hard Drive: settings to a file on the hard disk of the computer you are using. First, click the Save button.
Section 3 - Configuration Firmware Use the Firmware window to upgrade the firmware of the Router and install language packs. If you plan to install new firmware, make sure the firmware you want to use is on the local hard drive of the computer. If you want to install a new language pack, make sure that you have the language pack available. Please check the D-Link support site for firmware updates at http://support.dlink.com.
Section 3 - Configuration Dynamic DNS The DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased (www.whateveryournameis. com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to your server no matter what your IP address is.
Section 3 - Configuration System Check Ping Test: The Ping Test is used to send Ping packets to test if a computer is on the Internet. Enter the IP Address that you wish to Ping, and click Ping. Click Stop to stop sending Ping packets IPv6 Ping The IPv6 Ping Test is used to send IPv6 Ping packets to test Test: if a computer is on the Internet. Enter the IPv6 Address that you wish to Ping, and click Ping.
Section 3 - Configuration Schedules Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm. Name: Enter a name for your new schedule. Days: Select a day, a range of days, or All Week to include every day. Time: Check All Day - 24hrs or enter a Start Time and End Time for your schedule.
Section 3 - Configuration Status Device Info This page displays the current information for the DHP-1320. It will display the LAN, WAN (Internet), and Wireless information. If your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use Release to disconnect from your ISP and use Renew to connect to your ISP. If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed.
Section 3 - Configuration Logs The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the router logs. You can define what types of events you want to view and the level of the events to view.
Section 3 - Configuration Statistics The screen below displays the Traffic Statistics. Here you can view the amount of packets that pass through the DHP-1320 on both the WAN, LAN ports and the 802.11n/g (2.4GHz) wireless band. The traffic counter will reset if the device is rebooted. Refresh: Click the Refresh button to refresh the Router’s traffic statistics. Reset: Click the Reset button to reset the Router’s traffic statistics.
Section 3 - Configuration Internet Sessions The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer.
Section 3 - Configuration Routing Table This page displays the routing details configured for your router.
Section 3 - Configuration Wireless The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless clients.
Section 3 - Configuration IPv6 The IPv6 page displays a summary of the Router’s IPv6 settings and lists the IPv6 address and host name of any IPv6 clients.
Section 3 - Configuration Support D-Link DHP-1320 User Manual 102
Section 4 - Security Wireless Connection Setup Wizard To run the Wireless Connection Setup Wizard, click the Wireless Connection Setup Wizard button in the Setup>Wireless Settings window.
Section 4 - Security Wireless Security Setup Wizard Check the Manually set 5GHz band Network Name... box to manually set your desired wireless network name for the 5GHz band. Type your desired wireless network name (SSID). Automatically: Select this option to automatically generate the router’s network key and click Next. Manually: Select this option to manually enter your network key and click Next. If you selected Automatically, the summary window will display your settings.
Section 4 - Security If you selected Manually, the following screen will appear. Enter the Wireless Security Password you would like to use for your wireless network and click Next to proceed to the next window. The summary window will display your settings. Write down the security key and enter this on your wireless clients. Click Save to save your settings.
Section 4 - Security Add Wireless Device with WPS Wizard From the Setup > Wireless Settings screen, click Add Wireless Device with WPS. Select Auto to add a wireless client using WPS (Wi-Fi Protected Setup). Once you select Auto and click Connect, you will have a 120 second time limit to apply the settings to your wireless client(s) and successfully establish a connection. If you select Manual, a settings summary screen will appear. Write down the security key and enter this on your wireless clients.
Section 3 - Configuration Configuration (AP Mode) This section will show you how to configure your new D-Link wireless router using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter http://dlinkrouter or the IP address of the router (192.168.0.1). Select Admin in the User Name field. Leave the password blank by default.
Section 3 - Configuration Wireless Setup Wizard To use our web-based wizard to assit you in connecting your DHP-1320, click Launch Wireless Setup Wizard to begin. Click Next to continue your wireless network setup. Select one of the two configuration methods. Select WPS if your wireless device support WPS and click Next to continue to the next step. Press down the Push Button on the wireless device within 116 seconds.
Section 3 - Configuration If you would like to setup your network manually, select Manual and click Next to continue. Enter the SSID (Service Set Identifier). The SSID is the name of your wireless network. Create a name using up to 32 characters. The SSID is casesensitive. Select Assign a network key and click Next. Once this screen appears, the setup is complete. You will be given a detailed summary of your wireless security settings. Click Save to continue.
Section 3 - Configuration Wireless Setup Enable Check this box to enable the wireless function. If you Wireless: would prefer not to use wireless, uncheck the box to disable all the wireless functions. You may also set up a specific time range (schedule). Select a schedule from the drop-down menu or click Add New Schedule to create a new schedule.
Section 3 - Configuration Channel Width: Select the Channel Width: Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices. 20MHz - Select if you are not using any 802.11n wireless clients. Wireless Security Locking the wireless security settings prevents the settings from being changed by any new external user using its PIN. Devices Settings: can still be added to the wireless network using Wi-Fi Protected Setup.
Section 3 - Configuration Network Settings - DHCP This section will allow you to change the local network settings of the access point and to configure the DHCP settings. LAN Connection Use the drop-down menu to select Dynamic IP (DHCP) Type: to automatically obtain an IP address on the LAN/private network. Device Name: Enter the Device Name of the AP. Changing the Device Name is recommended if there is more than one D-Link device within the subnet.
Section 3 - Configuration Network Setup - Static IP Select Static IP to manually enter the IP address, subnet mask, and default gateway addresses. LAN Connection Select Static IP from the drop-down menu. Type: IP Address: Enter the IP address of the access point. The default IP address is 192.168.0.1. If you change the IP address, once you click Apply, you will need to enter the new IP address in your browser to return to the configuration utility. Subnet Mask: Enter the Subnet Mask.
Section 3 - Configuration My IPv6 Select Link-local only from the drop-down menu. Connection is: LAN IPv6 Address This section displays the IPv6 address of the router. settings: My IPv6 Select static IPv6 from the drop-down menu. Connection is: LAN IPv6 Enter the LAN (local) IPv6 address for the router.
Section 3 - Configuration My IPv6 Select Autoconfiguration (Stateless/DHCPv6) from the Connection: drop down menu. IPv6 DNS Select Obtain IPv6 DNS Server automatically or enter a Settings: specific DNS Server address.
Section 3 - Configuration Configuration PLC Settings - AP Mode This section will show you how to configure your new D-Link PowerLine AV using the web-based configuration utility.
Section 3 - Configuration Network You can set the name of your network and to make it Name: either public or private. Make sure the Network Name of all of the devices within your PowerLine network is the same. Public Select this option if you would like to make your Network powerline network public with the default Network Name: Name of “HomePlugAV”. Since this is a commonly used Network Name, it is less secure than a private Network Name.
Section 3 - Configuration Status: This field shows the status of the device. If the field displays the word Connect, then the device is connected to your PowerLine network. If the field displays the word Disconnect, then the device has been added to the network but it is not ready. Please check its password and make sure the device is powered on. QoS Setting: You can configure your PowerLine AV devices to give priority to powerline network traffic accordingly.
Section 3 - Configuration Network Filter Use MAC (Media Access Control) Filters to authorize wireless clients to access your network by their MAC addresses. When enabled, any client not on the MAC filter list will not be able to access your network. MAC Address Select Enable or Disable from the drop-down Filter: menu. MAC Address: Enter the MAC address you would like to filter. To find the MAC address on a computer, please refer to the Networking Basics section in this manual.
Section 3 - Configuration Advanced Wireless Transmit Sets the transmit power of the antennas. Power: Note: Transmit power is regulated by international standard. Users are forbidden to change its maximum limit. WLAN Select this checkbox to enable WLAN partition. If this Partition: feature is enabled, then there is no barrier between communication among wireless stations connecting to the Access Point. If this is disabled, wireless clients are not allowed to exchange data through the Access Point.
Section 3 - Configuration Wi-Fi Protect Setup Wi-Fi Protect Enables the Wi-Fi Protected Setup feature. Setup: Reset to Restores the default Wi-Fi setup. Unconfigure: Current PIN: Shows the current value of the access point’s PIN. Generate New Create a random number that is a valid PIN: PIN. This becomes the access point’s PIN. You can then copy this PIN to the user interface of the user. Reset PIN to Restores the default PIN of the access Default: point.
Section 3 - Configuration Add Wireless Device with WPS Adding a Wireless Device Using the PIN Method Please select one of the following configuration methods and click Next to continue.
Section 3 - Configuration Adding a Wireless Device Using the PBC Method Select PBC to use Push Button Configuration in order to connect to your network. Click Connect to continue. Press the WPS Button on the wireless device that you are adding to your network to complete the setup.
Section 3 - Configuration User Limit Settings In this section, you may set a limit to the number of wireless clients to prevent heavy wireless traffic.
Section 3 - Configuration Admin This page will allow you to change the Administrator password. The administrator password has read/write access. Password: Enter a new password for the Admin User Name. The administrator account can change the configuration of the device. Verify Enter the same password that you entered in Password: the previous textbox in order to confirm its accuracy. System Name: Enter DHP-1320.
Section 3 - Configuration Time This page will allow you to change the Administrator password. The administrator password has read/write access. Time Zone: Select the Time Zone from the drop-down menu. Daylight To select Daylight Saving time manually, select Saving: enabled or disabled, and enter a start date and an end date for daylight saving time. Enable NTP NTP is short for Network Time Protocol. NTP Server: synchronizes computer clock times in a network of computers. Check this box to use a NTP server.
Section 3 - Configuration System Settings Save Settings to Use this option to save the current router configuration Local Hard Drive: settings to a file on the hard disk of the computer you are using. First, click the Save button. You will then see a file dialog, where you can select a location and file name for the settings. Load Settings Use this option to load previously saved router from Local Hard configuration settings.
Section 3 - Configuration Firmware You can upgrade the firmware of the access point from this page. Make sure the firmware you would like to use is on the local hard drive of your computer. Click Browse... to locate the firmware file to be used for the update. Please check the D-Link support site for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from the D-Link support site.
Section 3 - Configuration Schedules Schedules can be created for use with enforcing rules. For example, if you would like to restrict web access to Mon-Fri from 3:00 p.m. to 8:00 p.m., you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a StartTime of 3:00 p.m. and End Time of 8:00 p.m. Name: Enter a name for your new schedule. Days: Select a day, a range of days, or All Week to include every day. Time: Check All Days or enter a start and end time for your schedule.
Section 3 - Configuration Device Info This page displays the current information for the DHP-W306AV. It will display the LAN and wireless LAN information. General: Displays the access point’s time and firmware version. LAN: Displays the MAC address and the private (local) IP settings for the access point. Wireless LAN: Displays the wireless MAC address and your wireless settings such as SSID and Channel.
Section 3 - Configuration Logs The DHP-W306AV keeps a running log of events and activities occurring on the AP. If the AP is rebooted, the logs are automatically cleared. You can save the log files under Log Settings. Log Options: You can select the types of messages that you would like to display from the log: System Activity, Debug Information, Attacks, Dropped Packets, and Notice. Select the types you want to view and click Apply Log Settings Now.
Section 3 - Configuration Statistics The DHP-1360 keeps statistics of the traffic that passes through it. You can view the amount of packets that pass through the LAN and wireless portions of the network. The traffic counter will reset if the access point is rebooted. Refresh Statistics: Click the Refresh button to refresh the Access Point’s traffic statistics.
Section 3 - Configuration Wireless This section allows you to view the wireless clients that are connected to your wireless access point.
Section 3 - Configuration IPv6 This section will display all of your IPv6 Internet and network connection details.
Section 3 - Configuration Support D-Link DHP-1320 User Manual 135
Section 4 - Security Wireless Security This section will show you the different levels of security you can use to protect your data from intruders. The DHP-1320 offers the following types of security: • WPA2 (Wi-Fi Protected Access 2) • WPA2-PSK (Pre-Shared Key) • WPA (Wi-Fi Protected Access) • WPA-PSK (Pre-Shared Key) What is WPA? WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
Section 4 - Security Configure WEP It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2. Click on Setup and then click Wireless Settings on the left side. 3.
Section 4 - Security Configure WPA/WPA2-Personal (PSK) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2. Click on Setup and then click Wireless Settings on the left side. 3.
Section 4 - Security Configure WPA/WPA2-Enterprise (RADIUS) It is recommended to enable encryption on your wireless router before your wireless network adapters. Please establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the added overhead. 1. Log into the web-based configuration by opening a web browser and entering the IP address of the router (192.168.0.1). 2. Click on Setup and then click Wireless Settings on the left side. 3.
Section 5 - Connecting to a Wireless Network Connect to a Wireless Network Using Windows® 7 It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Click on the wireless icon in your system tray (lower-right corner). Wireless Icon 2. The utility will display any available wireless networks in your area.
Section 5 - Connecting to a Wireless Network 3. Highlight the wireless network (SSID) you would like to connect to and click the Connect button. If you get a good signal but cannot access the Internet, check your TCP/IP settings for your wireless adapter. Refer to the Networking Basics section in this manual for more information. 4. The following window appears while your computer tries to connect to the router.
Section 5 - Connecting to a Wireless Network 5. Enter the same security key or passphrase that is on your router and click Connect. You can also connect by pushing the WPS button on the router. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 5 - Connecting to a Wireless Network Configure WPS The WPS feature of the router can be configured using Windows® 7. Carry out the following steps to use Windows® 7 to configure the WPS feature of the router: 1. Click the Start button and select Computer from the Start menu. 2. Click the Network option.
Section 5 - Connecting to a Wireless Network 3. Double-click the DHP-1320. 4. Input the WPS PIN number (displayed in the WPS window on the Router’s LCD screen or in the Setup > Wireless Setup menu in the Router’s Web UI) and click Next.
Section 5 - Connecting to a Wireless Network 5. Type a name to identify the network. 6. To configure advanced settings, click the icon. Click Next to continue.
Section 5 - Connecting to a Wireless Network 7. The following window appears while the Router is being configured. Wait for the configuration to complete. 8. The following window informs you that WPS on the DHP-1320 has been setup successfully. Make a note of the security key as you may need to provide this security key if adding an older wireless device to the network in the future. 9. Click Close to complete WPS setup.
Section 5 - Connecting to a Wireless Network Using Windows Vista® Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows Vista® utility as seen below. If you receive the Wireless Networks Detected bubble, click on the center of the bubble to access the utility.
Section 5 - Connecting to a Wireless Network Configure Wireless Security It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used. 1. Open the Windows Vista® Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower right corner of screen). Select Connect to a network. 2.
Section 5 - Connecting to a Wireless Network 3. Enter the same security key or passphrase that is on your router and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the security settings are correct. The key or passphrase must be exactly the same as on the wireless router.
Section 5 - Connecting to a Wireless Network Using Windows® XP Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Section 5 - Connecting to a Wireless Network Configure WPA-PSK It is recommended to enable WPA on your wireless router or access point before configuring your wireless adapter. If you are joining an existing network, you will need to know the WPA key being used. 1. Open the Windows® XP Wireless Utility by right-clicking on the wireless computer icon in your system tray (lower-right corner of screen). Select View Available Wireless Networks. 2.
Section 5 - Connecting to a Wireless Network 3. The Wireless Network Connection box will appear. Enter the WPA-PSK passphrase and click Connect. It may take 20-30 seconds to connect to the wireless network. If the connection fails, please verify that the WPA-PSK settings are correct. The WPA-PSK passphrase must be exactly the same as on the wireless router.
Section 6 - Troubleshooting Troubleshooting This chapter provides solutions to problems that can occur during the installation and operation of the DHP-1320. Read the following descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a different operating system, the screenshots on your computer will look similar to the following examples. 1. Why can’t I access the web-based configuration utility? When entering the IP address of the D-Link router (192.168.0.
Section 6 - Troubleshooting • Configure your Internet settings: • Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their defaults. • Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK. • Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
Section 6 - Troubleshooting 3. Why can’t I connect to certain sites or send and receive emails when connecting through my router? If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail, we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc). Note: AOL DSL+ users must use MTU of 1400. To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to.
Section 6 - Troubleshooting 1452 was the proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480). Once you find your MTU, you can now configure your router with the proper MTU size. To change the MTU rate on your router follow the steps below: • Open your browser, enter the IP address of your router (192.168.0.1) and click OK. • Enter your username (admin) and password (blank by default).
Appendix A - Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able to enjoy the freedom that wireless networking delivers.
Appendix A - Wireless Basics What is Wireless? Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office network. Why D-Link Wireless? D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link delivers the performance you need at a price you can afford.
Appendix A - Wireless Basics Home • Gives everyone at home broadband access • Surf the web, check email, instant message, etc.
Appendix A - Wireless Basics Where is wireless used? Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public places is usually called “hotspots”.
Appendix A - Wireless Basics Wireless Modes There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless router. • Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network adapters on each computer, such as two or more DHP-1320 wireless network Cardbus adapters. An Infrastructure network contains an Access Point or wireless router.
Appendix B - Networking Basics Networking Basics Check your IP address After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below. Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.) At the prompt, type ipconfig and press Enter.
Appendix B - Networking Basics Statically Assign an IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1 Windows® 7 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Change Adapter Settings. Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network Connections.
Appendix C - Technical Specifications Technical Specifications Standards • IEEE 802.3 • IEEE 802.3u • IEEE 802.11b • IEEE 802.11g • IEEE 802.
Appendix C - Technical Specifications • L = 5.5 inches (139.7 mm) • W = 8 inches (203.2 mm) • H = 1.5 inches (38.09 mm) Weight • 1.068 lbs (484.43 g) Wireless Signal Rates1 IEEE 802.11n: 20MHz Channel: • 1Nss: 65/72.2 Mbps (max) • 2Nss: 130/144.44 Mbps (max) 40MHz Channel: • 1Nss: 135/150 Mbps (max) • 2Nss: 270/300 Mbps (max) IEEE 802.11g: • 54Mbps • 48Mbps • 24Mbps • 18Mbps • 11Mbps • 9Mbps • 36Mbps • 12Mbps • 6Mbps Wireless Frequency Range2 (North America) • 2.412GHz to 2.462GHz (802.
Appendix D - Contacting Technical Support Contacting Technical Support U.S. and Canadian customers can contact D-Link technical support through our web site or by phone. Before you contact technical support, please have the following ready: • Model number of the product (e.g. DHP-1320) • Hardware Revision (located on the label on the bottom of the router (e.g. rev A1)) • Serial Number (S/N number located on the label on the bottom of the router).
Appendix E - Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty: • Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and • Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Appendix E - Warranty Limited Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its documentation.
Appendix E - Warranty • After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not include any manuals or accessories in the shipping package. DLink will only replace the defective portion of the product and will not ship back any accessories.
Appendix E - Warranty IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT.
Appendix E - Warranty CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Appendix E - Warranty ICC Notice: Operation is subject to the following two conditions: 1) This device may not cause interference and 2) This device must accept any interference, including interference that may cause undesired operation of the device. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.
Appendix F - Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.
