User Manual
Table Of Contents
- Table of Contents
- About This Guide
- 1 Product Introduction
- 2 Hardware Installation
- 3 Getting Started
- 4 SmartConsole Utility
- 5 Configuration
- Smart Wizard Configuration
- Web-based Management
- Tool Bar > Save Menu
- Tool Bar > Tool Menu
- Tool Bar > Smart Wizard
- Tool Bar > Online Help
- Function Tree
- Device Information
- System > System Settings
- System > DHCP Auto Configuration
- System > Trap Settings (For SmartConsole)
- System > Port Settings
- System > SNMP Settings > SNMP Global State
- System > SNMP Settings > User/Group Table
- System > SNMP Settings > SNMP Group Access Table
- System > SNMP Settings > SNMP View Table
- System > SNMP Settings > Community Table
- System > SNMP Settings > Host Table
- System > SNMP Settings > SNMP Engine ID
- System > SNMP Settings > SNMP Trap Settings
- System > Password Access Control
- System > System Log Settings
- Configuration > Jumbo Frame
- Configuration > 802.1Q VLAN
- Configuration > 802.1Q Management VLAN
- Configuration > Auto Surveillance VLAN > Auto Surveillance VLAN Settings
- Configuration > Voice VLAN > Voice VLAN Settings
- Configuration > Voice VLAN > Voice VLAN OUI Settings
- Configuration > Link Aggregation > Port Trunking
- Configuration > Link Aggregation > LACP Port Settings
- Configuration > IGMP Snooping > IGMP Snooping Configuration
- Configuration > Multicast Filtering Mode
- Configuration > Port Mirroring
- Configuration > Power Saving
- Configuration > Loopback Detection
- Configuration > SNTP Settings > Time Settings
- Configuration > SNTP Settings > TimeZone Settings
- Configuration > Spanning Tree > STP Global Settings
- Configuration > Spanning Tree > STP Port Settings
- QoS > Storm Control
- QoS > Bandwidth Control
- QoS > 802.1p/DSCP Priority Settings
- Security > Trusted Host
- Security > Safeguard Engine
- Security > ARP Spoofing Prevention
- Security > Port Security
- Security > SSL Settings
- Security > 802.1X > 802.1X Settings
- Security > MAC Address Table > Static MAC
- Security > MAC Address Table > Dynamic Forwarding Table
- Security > DHCP Server Screening > DHCP Server Screening Port Setting
- Monitoring > Statistics
- Monitoring > Cable Diagnostics
- Monitoring > System Log
- ACL > ACL Configuration Wizard
- ACL > ACL Profile List
- ACL > ACL Finder
- PoE > PoE Port Settings (DGS-1210-10P only)
- PoE > PoE System Settings (DGS-1210-10P only)
- Time-Based PoE > Time Range Settings (DGS-1210-10P only)
- LLDP > LLDP Global Settings (DGS-1210-10P only)
- LLDP > LLDP Remote Port Information (DGS-1210-10P only)
- LLDP > LLDP MED Settings (DGS-1210-10P only)
- 6 Command Line Interface
- Appendix A - Ethernet Technology
- Appendix B - Technical Specifications
- Appendix C – Rack mount Instructions
- _
5 Configuration D-Link Web Smart Switch User Manual
28
Function Tree
All configuration options on the switch are accessed through the Setup menu on the left side of the screen.
Click on the setup item that you want to configure. The following sections provide more detailed description
of each feature and function.
Figure 45 –Function Tree
Device Information
The Device Information provides an overview of the switch, including essential information such as firmware
& hardware information, and IP address.
It also offers an overall status of common software features:
RSTP: Click Setting to link to Configuration > Spanning Tree > STP Global Settings. Default is disabled.
Port Mirroring: Click Setting to link to Configuration > Port Mirroring. Default is disabled.
Storm Control: Click Setting to link to Configuration > QoS > Storm Control. Default is disabled.
Safeguard Engine: Click Setting to link to Configuration > Security > Safeguard Engine. Default is enabled.
IGMP Snooping: Click Setting to link to Configuration > IGMP Snooping. Default is disabled.
SNMP: Click Setting to link to System > SNMP Setting. Default is disabled.
802.1X: Click Setting to link to Configuration > Security > 802.1X > 802.1X Settings. Default is disabled.
802.1Q Management VLAN: Click Setting to link to Configuration > 802.1Q Management VLAN. Default is
disabled.
DHCP Client: Click Setting to link to System > System Setting. Default is disabled.
Figure 46 – Device Information