User Manual
Table Of Contents
- Table of Contents
- About This Guide
- 1 Product Introduction
- 2 Hardware Installation
- 3 Getting Started
- 4 SmartConsole Utility
- 5 Configuration
- Smart Wizard Configuration
- Web-based Management
- Tool Bar > Save Menu
- Tool Bar > Tool Menu
- Tool Bar > Smart Wizard
- Tool Bar > Online Help
- Function Tree
- Device Information
- System > System Settings
- System > DHCP Auto Configuration
- System > Trap Settings (For SmartConsole)
- System > Port Settings
- System > SNMP Settings > SNMP Global State
- System > SNMP Settings > User/Group Table
- System > SNMP Settings > SNMP Group Access Table
- System > SNMP Settings > SNMP View Table
- System > SNMP Settings > Community Table
- System > SNMP Settings > Host Table
- System > SNMP Settings > SNMP Engine ID
- System > SNMP Settings > SNMP Trap Settings
- System > Password Access Control
- System > System Log Settings
- Configuration > Jumbo Frame
- Configuration > 802.1Q VLAN
- Configuration > 802.1Q Management VLAN
- Configuration > Auto Surveillance VLAN > Auto Surveillance VLAN Settings
- Configuration > Voice VLAN > Voice VLAN Settings
- Configuration > Voice VLAN > Voice VLAN OUI Settings
- Configuration > Link Aggregation > Port Trunking
- Configuration > Link Aggregation > LACP Port Settings
- Configuration > IGMP Snooping > IGMP Snooping Configuration
- Configuration > Multicast Filtering Mode
- Configuration > Port Mirroring
- Configuration > Power Saving
- Configuration > Loopback Detection
- Configuration > SNTP Settings > Time Settings
- Configuration > SNTP Settings > TimeZone Settings
- Configuration > Spanning Tree > STP Global Settings
- Configuration > Spanning Tree > STP Port Settings
- QoS > Storm Control
- QoS > Bandwidth Control
- QoS > 802.1p/DSCP Priority Settings
- Security > Trusted Host
- Security > Safeguard Engine
- Security > ARP Spoofing Prevention
- Security > Port Security
- Security > SSL Settings
- Security > 802.1X > 802.1X Settings
- Security > MAC Address Table > Static MAC
- Security > MAC Address Table > Dynamic Forwarding Table
- Security > DHCP Server Screening > DHCP Server Screening Port Setting
- Monitoring > Statistics
- Monitoring > Cable Diagnostics
- Monitoring > System Log
- ACL > ACL Configuration Wizard
- ACL > ACL Profile List
- ACL > ACL Finder
- PoE > PoE Port Settings (DGS-1210-10P only)
- PoE > PoE System Settings (DGS-1210-10P only)
- Time-Based PoE > Time Range Settings (DGS-1210-10P only)
- LLDP > LLDP Global Settings (DGS-1210-10P only)
- LLDP > LLDP Remote Port Information (DGS-1210-10P only)
- LLDP > LLDP MED Settings (DGS-1210-10P only)
- 6 Command Line Interface
- Appendix A - Ethernet Technology
- Appendix B - Technical Specifications
- Appendix C – Rack mount Instructions
- _
5 Configuration D-Link Web Smart Switch User Manual
2
2
5
5
Figure 40 – Tool Menu > Reboot Device
Configuration Backup and Restore
Allow the current configuration settings to be saved to a file (not including the password), and if necessary,
you can restore configuration settings from this file. Two methods can be selected: HTTP or TFTP.
Figure 41 – Tool Menu > Configure Backup and Restore
HTTP: Backup or restore the configuration file to or from your local drive.
Click Backup to save the current settings to your disk.
Click Browse to browse your inventories for a saved backup settings file.
Click Restore after selecting the backup settings file you want to restore.
TFTP: TFTP (Trivial File Transfer Protocol) is a file transfer protocol that allows you to transfer files to a
remote TFTP server. Specify TFTP Server IP Address and File Name for the configuration file you want to
save to / restore from.
Click Backup to save the current settings to the TFTP server.
Click Restore after selecting the backup settings file you want to restore.
Note: Switch will reboot after restore, and
all current configurations will be lost
Firmware Backup and Upgrade
Allow for the firmware to be saved, or for an existing firmware file to be uploaded to the Switch. Two methods
can be selected: HTTP or TFTP.
Figure 42 – Tool Menu > Firmware Backup and Upload